We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Bakersfield, California 93311
Randy
Job Details: 03/07/2025
Gasket is not repairable without replacing whole door. Needs freezer door. ; ordrng 1 W11436967 (Door)
We serviced a
MAYTAG WASHER
Model MVWB865GW1
Near Bakersfield, California 93313
Randy
Job Details: 03/07/2025
Would not fill and shakes violently. Wont lock all the time. Found bad lid and wont read lid. Cracked on edges. Needs new lid. For water filRemoved and replaced valve. Same issue. Removed and replaced board. Now working and fills. Sounds rough when agitating. Removed agitator. Checked for damage. Has damage where meets Gearcase. No spanner nut on unit From last repair was not installed. This is not good for the machine. Need to rebuild and fix worn out parts. **********Requesting autho. Unit is in the second floor. Need 5 call count on return visit. ***********; rqstng P&A on 1 W10909670 (Nut spanner) and 1 W11550891 (Agitator) and 1 W10811960 (Basket) and 1 W11259006 (Lid) and 1 W11393685 (Gearcase) and 1 W11130356 (Suspension) and 1 W10915701 (Rotor)
We serviced a
KITCHENAID RANGE
Model KSGG700ESS7
Near Bakersfield, California 93313
Randy
Job Details: 03/07/2025
F2e1. Bad ui. Tested cannot remove code. Needs new ui. ; rqstng P&A on 1 W11029431 (Panel)
We serviced a
KITCHENAID RANGE
Model KSGG700ESS1
Near Thousand Oaks, California 91320
Richard
Job Details: 03/07/2025
"Tech support 7741026699 Brandon upon arrival inspected unit pumped out temperature sensor at room temp it owned at 1100 K which is good top burners were not sparking during my inspection of that. I found spark switches not connected correctly. Reconnected them all top burners are working now after that contact the tech-support ran a average temp. Check on the unit. Unit reached 425° got down to 297°. You could hear the valve open, but the spark module would never spark again at this point tech-support advised me to order a DSI board for the unit this job will need to be scheduled during the week. All parts are ordered by the office but will need to be during the week so I can re-document with tech-support.; O-emld tckt"
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM6175DK6BB
Near Bakersfield, California 93314
Aaron
Job Details: 03/07/2025
Checked the unit noises turntable motor and shaft order one for this unit; ordrng 1 WB26X10226 (motor ac synchronous) and 1 WB06X10873 (shaft turntable)
We serviced a
KITCHENAID M/W OTR
Model KMHS120ESS11
Near Bakersfield, California 93311
Aaron
Job Details: 03/07/2025
Needs 2 call count Complaint is that the turntable motor no longer works after the hearing of pop noise and no power going to turntable motor from the board order parts to correct tissue ; ordrng 1 W11545876 (Main board) and 1 W10642989 (motor-turn)
We serviced a
SPEED QUEEN WASHER
Model AFNE9BSP117TW13
Near Bakersfield, California 93308
Felipe S
Job Details: 03/07/2025
Upon arrival found unit leaking water on the dispenser door again. Call tech line and after inspection found unit needs some restrictions washer for the water supply line. SR: 2501012947 Pat ; ordrng 2 802254 (Water restric)s
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Los Angeles, California 91367
Richard
Job Details: 03/07/2025
"Upon arrival, inspected unit and diagnostics ran unit icemaker harvest unit never finished harvest checked test 56 unit gave an E5 error code bad icemaker ordering a new icemaker for the unit. Customer would like Friday the 14th in the afternoon.; ordrng 1 W11658802 (Ice maker aaymbley)"
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Bakersfield, California 93306
ERICK H
Job Details: 03/07/2025
"Cx states clothes are went at the end of quick wash cycle. Cx has no issues with any other cycle. Checked drain pump for obstructions. No obstructions on drain pump or coin catch. Cx has clothes in washer, ready for testing. Performed a full quick wash cycle with the clothes Cx had in unit. Unit completed cycle with no functional failures. Clothes is damp but not soaked. Cx also confirmed that it was acceptable and not too wet. After a more in depth conversation with the Cx, stated that they like to use the quick wash cycle for their clothes because of the short length of quick wash cycle. Cx is having clothes too wet at end of cycle due to the load size being too large. Cx is washing jeans, bath towels, and other bulky items with quick wash cycle. I explained to Cx that the quick wash cycle is designed for light and small loads. Bigger and heavier loads will not wash properly on quick wash cycle. Unit operating as designed. Will pseudo call for Tuesday to document with WPL techline. ; schdld next appmnt for 3/11 TUE !"
We serviced a
WHIRLPOOL DISHWASHER - BUI
Model WDF332PAMS0
Near Riverbank, California 95367
Andrew
Job Details: 03/07/2025
Cx complaint DW leaking under. Upon arrival. Ran diagnostics. Found leaking 8269144a hose. ; ordrng 1 8269144a (Hoses)
We serviced a
MAYTAG DRYER
Model MDG5500AWW
Near Los Angeles, California 91326
Sean W
Job Details: 03/07/2025
"Drum not turning and pulley,belt and rollers are intact,motor has no resistance and is shorted out,parts list has two motors available and no explanation of the difference between the two,ordered both motors.; ordrng 1 W10410997 (Motor) and 1 WP33002795 (Motor number two)"
We serviced a
WHIRLPOOL DRYER
Model MGD8630HC3
Near Bakersfield, California 93312
Joe P
Job Details: 03/07/2025
"Code F3E5, moisture sensor is open. Ordering moisture sensor will return to install and re-diagnose.; ordrng 1 W10906551 (Moister sensor)"
We serviced a
GENERAL ELECTRIC DRYER - GAS
Model PFD87GSPV0RS
Near Santa Margarita, California 93453
Leo
Job Details: 03/07/2025
"Opened up dryer andReplaced hi limit, backup,outlet and safety thermostat, also outlet thermistor, gas valve assembly and igniter, close it all up and still unit is not heating,Calling tech line tomorrow. SENSOR WE04X10189, GAS VALVE WE11X29741, IGNITER FLAT WE04X10183 and ; ordrng 1 WE04X10189 (FLAME SENSOR) and 1 WE11X29741 (GAS VALVE) and 1 WE04X10183 (IGNITER FLAT)"
We serviced a
GENERAL ELECTRIC RANGE - ELECTRIC
Model PSA9120SP1SS
Near San Luis Obispo, California 93401
Leo
Job Details: 03/07/2025
"Cx reached out to notify not being available, will try and try getting job done tomorrow if at all possible.; schdld next appmnt for 3/8 SAT !"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Los Banos, California 93635
David
Job Details: 03/07/2025
Found door heater malfunctioning ordering door; ordrng 1 W11566705 (Door)
We serviced a
GENERAL ELECTRIC RANGE - ELECTRIC
Model PTS7000SN4SS
Near Chowchilla, California 93610
David
Job Details: 03/07/2025
Found failed high limit switch ordering switch; ordrng 1 Wb24t10164 (High limit switch)
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRMC2285AF
Near Fresno, California 93727
Timothy
Job Details: 03/07/2025
The main water line out of the primary valve is broken. This is the manifold assembly I am replacing the inlet valve and supply line too.; ordrng 1 5304532655 (Supply tube) and 1 5304536607 (Valve) and 1 5304533202 (Manifold)
We serviced a
GE REFRIGERATOR
Model ZISS360DHBSS
Near Madera, California 93637
David
Job Details: 03/07/2025
Will need drain pan update ordering drain pan$370.14 CC Auth# TCF3V3; ordrng 1 WR17X29775 (Drain pan)
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFUE2022AW
Near Gustine, California 95322
Nick D
Job Details: 03/07/2025
"Tested defrost heater no ohms found, unit was completely defrosted and left unplugged; ordrng 1 5304533259 (Control board)"
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Patterson, California 95363
Nick D
Job Details: 03/07/2025
Gear case making loud noise error code F7E9 locked rotor needs new bearing and agitator replaced; ordrng 1 W11393685 (Gear case) and 1 W11550891 (Agitator)
We serviced a
GENERAL ELECTRIC RANGE - ELECTRIC
Model JBS160DM4BB
Near Dinuba, California 93618
J.E.
Job Details: 03/07/2025
Cycled unit broken thermostat. Quote for just parts and labor 351.41 customer agreed. Ordering part; ordrng 1 WB24X21192 (Thermostat)
We serviced a
WHIRLPOOL LAUNDRY
Model WTW8127LC1
Near Lathrop, California 95330
Andrew
Job Details: 03/07/2025
Water leaking causing property damage. Cx complaint. Upon arrival. Ran diagnostics. Found valve W11595805 assembly faulty. Leaking. Ordered part. W11621181; ordrng 1 W11621181 (Valve assembly) and 1 W11595805 (Valve)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ01
Near Los Angeles, California 91405
Oscar
Job Details: 03/07/2025
"Visual and physical inspection shows a freezers door that was left open for a long while and frosted up even the evaporator fan motor also, some water has been dripping from freezers to fridge. Replacing tagged parts and components recommended. ; ordrng 1 W11390538 (Controller) and 1 W11466252 (Wire jumper with fuse)"
We serviced a
MAYTAG WASHER
Model MHW6630HW0
Near Apple Valley, California 92307
Cesar
Job Details: 03/07/2025
Replaced control tested unit all checked good
We serviced a
KITCHENAID OVEN
Model KEBS279BSS00
Near Los Angeles, California 91316
Oscar
Job Details: 03/07/2025
"As all predisposed components and parts were replaced, a functional testing was conducted on bake and broil to customers satisfaction."
We serviced a
WHIRLPOOL RANGE
Model WFES3030RW0
Near Baywood-Los Osos, California 93402
Leo
Job Details: 03/07/2025
"Removed and replaced glass coocktop, tested all 4 burners and they all worked correctly,Job complete."
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Santa Clarita, California 91354
Felipe S
Job Details: 03/07/2025
"Remove old gear case and tub from the unit. Install the new ACU, slider, outer tub, gear case, drain pump and lower harness. Retest the unit and now is working properly. Job complete"
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS01
Near Los Angeles, California 91403
Tim B
Job Details: 03/07/2025
Replaced door and tested. Unit functions as normal. Cx will see ice by tomorrow.
We serviced a
MAYTAG WASHER
Model MVWC565FW0
Near Riverside, California 92508
Robert U.
Job Details: 03/07/2025
I replaced all parts ordered and took photos of the entire process. After repair I recalibrated the control and ran a diagnostic cycle. All functions are now restored and working. Job completed.
We serviced a
WHIRLPOOL DISHWASHER
Model DU1345XTVB0
Near Bakersfield, California 93306
James
Job Details: 03/07/2025
Transferred components to new racks and installed into unit. Unit complete.
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JW4
Near Turlock, California 95380
Cruz
Job Details: 03/07/2025
"Fixed- installed all new parts (2 switches, 2 burners, 2 receptacles) tested unit, everything is working per design- cx ok repair"
We serviced a
ZLINE REFRGERATOR
Model RFM-W-36-BS
Near Riverside, California 92509
Robert U.
Job Details: 03/07/2025
I removed and replace the inverter for the compressor. It took a little while there most be a delay but the compressor and condenser fan turned on. I then reinstalled control cover and compressor compartment cover. I checked the temp in the refrigerator and started at 50-50 degrees and before I left it was at 43. The unit is a triple evaporator so it will take 24-48 hours for temps to normalize. Customer is aware. Job completed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHV04
Near Rialto, California 92376
Francisco
Job Details: 03/07/2025
Removed braided line and installed pex line. No damage or leaks at this time. Cx will flush out 2 gallons of water and dump out two buckets of ice to clear it outSr#7741096922
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Littlerock, California 93543
Jonathan B.
Job Details: 03/07/2025
"JB OUT 3/7/25Installed replacement interlock replacement ACU W11513246 as ordered (after installation of replacement Lower Harness (Last visit).Reassembled control panel. Tested unit in Drain and spin. Unit successfully drained waterfront washtub and did spin.Cancelled cycle.Tested operation in NORMAL cycle.Verified correct water fill and agitation functions.Cancelled cycle. Tested again in Drain and Spin. Again verified correct Drain Pump and Spin functions.Unit is now operating as designed.NOTE: During Drain portion of cycle, water DID BACK UP FROM STANDING HOSE (BLUE HOSE BEHIND WASHER).Advised (2nd Time) for customer to install an AIR GAP DEVICE located where washing machine drain hose enters drain pipe (Blue Hose behind washer) AND VERIFY THAT THE BLUE HOSE GOING OUTSIDE THE HOUSE IS NOT BLOCKED OR RESTRICTED.NO CHARGE TO CUSTOMER JOB COMPLETE"
We serviced a
MAYTAG DRYER
Model MGD6230HW3
Near Bakersfield, California 93314
Joe P
Job Details: 03/07/2025
"Install driver repair kit and exhaust, tested unit no longer making squealing noise. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Montclair, California 91763
Jaime
Job Details: 03/07/2025
Had main control replaced. Washer Ok
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model GFE28GYNHFS
Near Bakersfield, California 93312
Joe P
Job Details: 03/07/2025
"Install defrost heater with harness check system after done defrost heater is working, unit is cooling and operating correctly to manufacture specs. Job complete."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Patterson, California 95363
Nick D
Job Details: 03/07/2025
"Start button replaced, started dryer 3x all working well and heating"
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW2
Near Oxnard, California 93033
Ian Y
Job Details: 03/07/2025
"Removed and replaced units splutch, shifter, agitator, gearcase, and drive hub. Tested, unit no longer leaking and performing as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Merced, California 95340
Manuel B
Job Details: 03/07/2025
Wash plate broken and slider out.install new wash plate slider.test washer working good.; used 1 W10734521 (Slider) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ00
Near Los Angeles, California 91405
Oscar
Job Details: 03/07/2025
"After replacement of all pre diagnosed parts and components were installed, dispenser resumed to normal operation, and consumer was asked to allow 24-48 hours for temperatures to stabilize and ice maker to harvest."
We serviced a
KITCHEN AID RANGE
Model KSGG700EBS1
Near La Crescenta-Montrose, California 91214
Oscar
Job Details: 03/07/2025
The light bulbs have been replaced and oven lights are back to normal operation.
We serviced a
GE CAFE RANGE
Model CGS750P2M3S1
Near Paso Robles, California 93446
Jack
Job Details: 03/07/2025
Replacing control board. Ran a test and unit is reading error 200. Dillon with tech line. 15900842. Found upper harness for sensor was lose at the sensor. Not board. All together unit is now functioning and working as designed. Job completed
We serviced a
WHIRLPOOL UNV
Model WRQA59CNKZ
Near Lancaster, California 93534
Samson
Job Details: 03/07/2025
"Replaced bad light module, unit test ok. Complete"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Livingston, California 95334
Cruz
Job Details: 03/07/2025
"Fixed- installed new parts (stator, ACU, harness) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"
We serviced a
ZLINE RANGE
Model RG36
Near Santa Paula, California 93060
Isidro
Job Details: 03/07/2025
"I tested the CO with Carbon0.590 to 0.640on the bake cycle, and 0.460 on broil when reached max temperature unit is operating as designed at this time of service"
We serviced a
WHIRLPOOL DRYER
Model WED8000DW4
Near Merced, California 95341
Manuel B
Job Details: 03/07/2025
Dryer no heating bad heat element.install new heat element test heater work good.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Santa Paula, California 93060
Ian Y
Job Details: 03/07/2025
"Removed and replaced unit water valve assembly, and main control. Tested unit no longer spilling water on the floor. Explain to customer while using heavier loads its possible for a small spray of water to hit between the cabinet and basket therefore getting small amount of water on floor."
We serviced a
WHIRLPOOL DRYER
Model WGD5010LW3
Near Tehachapi, California 93561
Samson
Job Details: 03/07/2025
"Replaced broken pad sensor, unit tested ok. Complete"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Bakersfield, California 93313
Randy
Job Details: 03/07/2025
Loud during use. Every cycle. Found bad cam. Stripped due to actuator not working correctly. Removed and replaced actuator and pulley. Tested now working as designed
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Bakersfield, California 93308
James
Job Details: 03/07/2025
"Installed new vent fan and tested unit. Unit drained, filled and washed as intended."
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Bakersfield, California 93306
Brandon
Job Details: 03/07/2025
Installed new control board and ran calibration.
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Baywood-Los Osos, California 93402
Leo
Job Details: 03/07/2025
"Removed and replaced main control board, calibrated and tested unit and it works properly,Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Turlock, California 95380
Cruz
Job Details: 03/07/2025
"Fixed- installed new parts (cntrl elec, tub ring, latch) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC704FPS04
Near Colton, California 92324
Francisco
Job Details: 03/07/2025
Removed and replaced ice maker tested ops unit working properly no damage by tech
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Oxnard, California 93035
Kenneth
Job Details: 03/07/2025
Applied gasket material under the door gasket per tech line request. Customer will call back if condensation still forms. If customer calls back. Please order me more gasket material so I can apply it to the bottom of the door as well as Im calling tech line.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Stevinson, California 95374
Nick D
Job Details: 03/07/2025
"Found lid lick not making contact, lid pushed down, popped lid got washer to start normal."
We serviced a
KITCHEN AID REFRIGERATOR
Model KBFN402ESS02
Near Templeton, California 93465
Jack
Job Details: 03/07/2025
Running a test to see why no cool. Now unit is cooling now. Unit is freezing and fresh food is good also. Running temps to see were we are at. Unit is now reading 2 degrees in freezer and customer is putting ice cube tray in there and fresh food area is now reading 37.6 degrees. Unit is now cooling and working as designed. Took a little bit for it to cycle. Job completed.
We serviced a
FRIGIDAIRE DISHWASHER
Model GDSP4715AF0A
Near Camarillo, California 93012
Isidro
Job Details: 03/07/2025
"I found the unit with stuck button or loose wire harness, I reinstalled wire harness, unit is now responding and washing as designed at this time of service"
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Gustine, California 95322
Nick D
Job Details: 03/07/2025
"Actuator, capacitor,splutch kit replaced, ran washer for agitator movement."
We serviced a
WHIRLPOOL DRYER
Model WED8000DW4
Near San Bernardino, California 92407
Francisco
Job Details: 03/07/2025
Removed and replaced element u it now working properly
We serviced a
ZLINE REFRIGERATOR
Model RBIV-30
Near Los Angeles, California 91406
Oscar
Job Details: 03/07/2025
"Upon arriving, consumer presented me with a new main controller sent to him by Zline, and also said that Zline instructions were to replace it. so I have installed new board as per Zline instructions to customers.Also, asked customer to please allow at least 24 hours for unit to resume normal operation."
We serviced a
KITCHENAID OVEN
Model KOEC527PSS01
Near Delano, California 93215
Esteban
Job Details: 03/07/2025
"File number 7741099023 called tech line tested recommended pulling unit out and check for independent ground wire not bonded to neutral. Replaced UI. Unit passed all test. Unit is working as intended. Unit is working as designed. Job took an hour to complete, asking for 2 job count."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Simi Valley, California 93065
Paul
Job Details: 03/07/2025
"Unit was not spraying, replaced motor and ran diagnostics unit is now working properly."
We serviced a
GENERAL ELECTRIC RANGE
Model JGRP1 6GEP3BG
Near Oxnard, California 93035
Kenneth
Job Details: 03/07/2025
Installed igniter and tested unit. Unit is working properly. Customer approves function at this time. Collected $440.61 via CC on iWallet (Autho# 4VL4YT)
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Thousand Oaks, California 91362
Richard
Job Details: 03/07/2025
"Upon arrival, removed bad filter housing installed new one tested unit unit is working as intended. Unit is making ice now advised customer to only use factory recommended water filters. All operations are normal now job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Turlock, California 95380
Cruz
Job Details: 03/07/2025
"Fixed- found strike to be broken, causing unit not to start- look at pictures- removed and replaced (strike) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1835VBB
Near Tulare, California 93274
Enrique
Job Details: 03/07/2025
Installed defrost timer. Refrigerator operating as designed. No leaks.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Atwater, California 95301
Cruz
Job Details: 03/07/2025
"found burnt terminal block, found melt wire from power cord to terminal block- look at pictures- cx will not continue with repair-"
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Delano, California 93215
Esteban
Job Details: 03/07/2025
UI not responding when rotating knob UI was removed and replaced. Unit is working properly now. Unit passed all test. Unit is working as intended.
We serviced a
WHIRLPOOL REFRGERATOR
Model WRF560SEHW03
Near Oak View, California 93022
Kenneth
Job Details: 03/07/2025
Installed damper. Sealed around the cover. Covered some holes around the damper wires. Defrosted the ice in reservoir. Unit is working properly.
We serviced a
WHIRLPOOL DRYER
Model WGD4890XQ1
Near Port Hueneme, California 93041
Isidro
Job Details: 03/07/2025
"I cut off the old broken blower wheel, installed and secured new motor, brackets and blower wheel, unit is now blowing and operating as designed at this time of service, cx approved repair and service"
We serviced a
GENERAL ELECTRIC WASHER
Model PFQ97HSPV0DS
Near Acton, California 93510
Jonathan B.
Job Details: 03/07/2025
"JB OUT 3/7/25Customer states that the error code 353 displayed and dryer did not completely dry clothes.Upon arrival connected Smart HQ diagnostic tool and found No Saved Error Codes.Ran Test 15 and found Compressor and all 4 NTSs passed.Ran Test 18 (Blower test) and it passed.Unable to duplicate complaint or error code.Unit currently has passed all diagnostic tests, unable to verify complaint on this visit."
We serviced a
KITCHENAID M/W OTR
Model KMHC319LSS00
Near Arroyo Grande, California 93420
George
Job Details: 03/07/2025
Installed parts tested check out ok complete.
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Delhi, California 95315
Cruz
Job Details: 03/07/2025
"Fixed- found bolt to rotor had pop off causing loud clicking noise and balancing issues- add Loctite to bolt, reseated, tested, calibration trst pass- no leaks- no errors- cx ok repair"
We serviced a
KITCHENAID M/W OVEN WALL
Model KOCE500ESS23
Near Perris, California 92570
Kevin
Job Details: 03/07/2025
Unit is giving error code for communication error. I removed control panel and found roaches in console. Failed console. Customer declined at this time.
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Arroyo Grande, California 93420
George
Job Details: 03/07/2025
Installed part tested check out ok complete .
We serviced a
MAYTAG DRYER
Model MGD6230HW3
Near Bakersfield, California 93314
Aaron
Job Details: 03/07/2025
"Replaced the Ui board , asm tested operations ok now at this time"
We serviced a
GENERAL ELECTRIC WASHER
Model GTW585BSV2WS
Near Hanford, California 93230
Enrique
Job Details: 03/07/2025
"Installed Gearcase, speed sensor, agitator base and auger. Washer operating as designed."
We serviced a
MAYTAG WASHER
Model MVW6230HW1
Near Riverside, California 92503
Robert U.
Job Details: 03/07/2025
Found the cam assembly dropped down and was making contact with the shield. I replaced the cam assembly and the belt and ran a diagnostic cycle. All functions returned to normal. No error codes were stored. All functions restored and working after repair. I took photos of the process. Job completed. ; used 1 W11239857 (Belt) from stock
We serviced a
WHIRLPOOL DISWASHER
Model WDTA50SAKZ3
Near Calabasas, California 91302
Richard
Job Details: 03/07/2025
Replaced low spry arm tested unit all operations are normal operating as complete.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Victorville, California 92395
Cesar
Job Details: 03/07/2025
Found unit not draining found pump will not run pump is getting 120v determined failed pump replaced pump all tested good
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Visalia, California 93291
J.E.
Job Details: 03/07/2025
Cycled unit and found worn hub installed new hub and retested unit now working as designed job completed ; used 1 W10528947 (Cam) from stock
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LFTR2045VF
Near Santa Maria, California 93458
George
Job Details: 03/07/2025
Installed part tested check out ok complete.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Bakersfield, California 93314
Randy
Job Details: 03/07/2025
Unit is nott draining. Tested and found faulty pump. Removed and replaced drain pump. Tested and now working as designed
We serviced a
WHIRLPOOL DRYER - ELECTRIC
Model MGD4500MW0
Near Los Angeles, California 91343
ERICK H
Job Details: 03/07/2025
"Blower wheel has separated from motor, causing clothes not to dry. Reinstalled blower wheel. Unit operating as designed. Job complete."
We serviced a
WHIRLPOOL WASHERHER
Model WTW5010LW0
Near Tulare, California 93274
Enrique
Job Details: 03/07/2025
"Installed lower harness, performed calibration. Washer operating as designed. No leaks."
We serviced a
GENERAL ELECTRIC WASHER
Model PTW600BSR1WS
Near Wasco, California 93280
Esteban
Job Details: 03/07/2025
Rods were removed and replaced. Unit passed all test. Unit is working as intended.
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Modesto, California 95355
Andrew
Job Details: 03/07/2025
Vibrating/shaking/walking Teh unit is walking across the floor. Cx complaint. Upon arrival. Ran diagnostics. Found loose shocks. Reattached shocks. Tested components out. Okay. Operation as according to protocol designed.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHT1835VW
Near Porterville, California 93257
J.E.
Job Details: 03/07/2025
Cycled unit and found faulty evaporator fan motor. Installed new motor and retested unit now working as designed job completed ; used 1 242219206 (Evaporator fan motor) from stock
We serviced a
MAYTAG WASHER
Model MVWB865GC0
Near Manteca, California 95337
William
Job Details: 03/07/2025
"F3E2, F0E4, F8E1, found low water flow thru water valve, replaced water valve, ran self diagnostic cycle, unit operating as designed d cx xo"
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Los Angeles, California 91344
Sean W
Job Details: 03/07/2025
"Fabric softener not dispensing and being flushed into tub upon arrival,Ui displaying F5E2,called tech line and was advised to check for obstructions and replace water valves,found no obstructions and replaced both water valves,successfully ran diagnostic cycle,washer no longer displaying error codes and is working properly.Sr # 7741097386"
We serviced a
MAYTAG WASHER
Model MVW5430MW2
Near Azusa, California 91702
Stephen
Job Details: 03/07/2025
Water tested washer. No leaks from washer. Found water stain on hose coupling and under hot water hose connection to water inlet valve. Advised customer to call dealer( Home Depot ) to replace both hot and cold fill hoses( not part of washer ). Washer is working properly as designed. Complete.
We serviced a
MAYTAG WASHER
Model MHW6630HW2
Near Oxnard, California 93030
Ian Y
Job Details: 03/07/2025
"Removed and replaced hot and cold valve. Tested, unit now performing as designed."
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Rancho Cucamonga, California 91701
Jaime
Job Details: 03/07/2025
Replaced cam assembly. Washer machine Ok
We serviced a
KITCHEN AID DISHWASHER
Model KDTM354DSS5
Near Los Angeles, California 91345
ERICK H
Job Details: 03/07/2025
"Cx states dishwasher leaks intermittently. Leak starts at beginning of cycle. Cx states they use 2 detergent pods. There was trash in filter and 2 pods in rear of unit. Pics provided. Ran dishwasher for 15 minutes. Could not replicate issue. I did see a lot of detergent buildup inside of the tub and suds. Cx is using too much detergent, causing unit to leak. Unit operating as designed. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW0
Near West Covina, California 91790
Stephen
Job Details: 03/07/2025
"Ran diagnostics. Cycle goes to done. Found belt slipping, weak capacitor, and worn splutch. Replaced control, splutch, capacitor, and belt. Locks/ unlocks, fills, agitates, drains, rinses, dispenses, and spins properly at this time. Complete. ; used 1 WPW10006384 (Belt), 1 W11395618 (Capacitor), and 1 W10721967 (Splutch) from stock"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Orange Cove, California 93646
J.E.
Job Details: 03/07/2025
Cycled unit and found loose pulley. Tightened and secured pulley retested unit now working as designed job completed
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Fontana, California 92337
Francisco
Job Details: 03/07/2025
"Checked unit found multiple codes for pressure and drain issue. Found pump running but not draining properly. Found broken impeller. Removed and replaced pump, calibrated and tested ops unit working properly. Advised Cx checking pockets before running it. No damage by tech.. F9 e1F3 e2F7 e9"
We serviced a
GENERAL ELECTRIC DRYER
Model GTD33EASK0WW
Near California City, California 93505
Samson
Job Details: 03/07/2025
"Replaced bad door switch, unit test ok. Complete"