Local Reviews
Powered by Fluid LOCAL
Kenneth M.
REFRIGERATOR WHIRLPOOL WRX988SIBM03 Found unit wi5 issues with the in freezer. Found brackets for freezer door thumping while rolling door out. Bearings on brackets falling off. Ordering new brackets. Top rack brackets are broken not allowing top rack to stay stationary. Ordering brackets. Rescheduled customer for 3-20-19; ordrng 1 W10625067 (bracket) and 1 W10625068 (bracket) and 1 W10850332 (bracket) and 1 W10858092 (bracket) and 4 WP67006908 (screw)s
Jim S.
RANGE BOSCH NGM8055UC/02 Installed all five ignitor; used 5 00189345 (IGNITOR) from stock
Jim S.
REFRIGERATOR WHIRLPOOL KFIS29PBMS00
Jim S.
DISHWASHER WHIRLPOOL GU2455XTSQ1 Replaced open heater.
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFHB2740PP5A
Jim S.
DISHWASHER WHIRLPOOL WDT720PADM2 Installed new wash motor
Jesus C.
WASHER WHIRLPOOL WTW4800BQ1 Unplugged unit and removed remaining water from unit. Removed drain pump and installed new pump. Assembled unit and ran auto test. Unit is now working as design.
Jesus C.
REFRIGERATOR KITCHENAID KFIS20XVMS11 "Customer states that unit is leaking from freezer section. Found ice build up in the lower section of the freezer. Pulled unit out and removed compartment cover. Removed drain kit and installed new drain tube. Assembled and pushed unit back in. Removed door and drawers. Removed iced build up and defrosted ice. Cleaned out water and assembled unit. Unit is now working as design.; used 1 8201711 (ADHESIVE), and 1 W10619951 (TUBE DRAIN) from stock"
Jesus C.
WASHER MAYTAG MVWB765FW1 Customer states that unit is not Filling. Ran test and found several error codes. Unplugged unit and remove UI panel. Turned off water and removed hoses. Removed valve and assembled unit. Calibrated unit and ran auto test. Unit is now working as design.F3-E2. Inlet water tempF0-E4 spin limited by water temperatureF2-E1. Stuck button
Jesus C.
RANGE JENN-AIR JES9800CAS01 Unplugged unit and removed panel. Removed control board and disconnected. Installed new panel and assembled unit. Plugged unit back in and tested. Unit is now working as design.
Jesus C.
REFRIGERATOR KITCHENAID KBFC42FTS08 Turned unit off at main panel. Removed icemaker bin and freezer drawer. Removed optics and installed new. Assembled unit and turned power on. Unit did not cycle. Turned unit back off and inspected optics and icemaker. Removed icemaker and checked proper connection.
Jim S.
WASHER WHIRPOOL WFW6620HW0 F8E1According to the customer the delivery guys removed the locking bolts and then placed the unit on its back to install the pedestal. This causes the spring to stretch and the struts to pull apart. The drain hose was pushed down the drain so far it was causing the water to symphonic out.; ordrng 2 W11314394 (SPRING)s and 4 W11316766 (STRUTS)s
Jim S.
REFRIGERATOR THERMADOR T30BB910SS/03 Board was not ordered
Jesus C.
MICROWAVE WHIRLPOOL WMH31017HS2
Jim S.
REFRIGERATOR WHIRLPOOL WRX986SIHV00 12 volts out of the board to the lights but it looses voltage down the line; ordrng 1 W11205083 (L.E.D.) and 1 W11239944 (HARNESS W/LIGHTS)
Jesus C.
REFRIGERATOR KITCHENAID KRMF706ESS01 "Customer states that unit is making loud noise. Ran tests and found the freezer making noise. The evaporator has ice build up that it’s hitting fan blade. Removed door, drawers and evaporator cover. Defrosted all the ice and assembled unit. Also found the melted ice coming out from bottom. Pulled unit out and removed compartment cover, removed drain tube and found it clogged. Cleared tube abs assembled unit. Unit is now working as design."
Jim S.
REFIRGERATOR KITCHEN AID KRMF706EBS01
Jesus C.
DISHWASHER KITCHENAID KUDE60HXSS1 Customer states that unit is not turning on. Ran diagnostics and found error code. Removed power and lower kick plate. Removed motor connector and reseated. Plugged unit back in and ran diagnostics. Unit filled and ran. Unit is working as designed.
Jesus C.
REFRIGERATOR KITCHENAID KRFC704FPS00 Customer had unit defrosted upon arrival. Removed drawers and evaporator cover. Placed thermistor in proper location per service pointer W11033419C. Assembled unit and pulled unit. Removed control board cover and replaced control. Assembled unit and tested. Unit is now working as design.
Jesus C.
REFRIGERATOR KITCHENAID KRFC300EBS00 Customer states that unit is leaking water. Checked unit and also found water leaking from icemaker. Replaced icemaker and also found the freezer gasket not sealing properly. Heated gasket and conformed to unit. Cycle icemaker and it’s working properly. Unit is now working as design.
Jesus C.
DRYER WHIRLPOOL WTW8500DC5 Customer states that unit is not filling properly. Ran test and found error codes. Removed liver and UI panel. Removed valve and installed new valve. Calibrate unit and ran auto test. Unit is now working as design.F7-E0. Loss of powerF0-E3 OverloadF8-E1. Long fill.
James M.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Replaced hose and tested unit. No leaks at this time and hose clamps are good. Job complete. Customer not home. Contractor signed.
James M.
DISHWASHER MAYTAG MDB4949SHW
James M.
DISHWASHER WHIRLPOOL WDT720PADM2 F3e3 owi error. Removed owi and cleaned sensor and filter. No more error. Replaced cntrl electric and tested u it. Unit is functioning properly at this time
Jesus C.
DISHWASHER KITCHENAID KDTE234GPS0 Customer states that unit is not latching and open during cycle. Checked unit and inspected latch mechanism. Removed front panel and checked for any obstructions. Assembled and unit is not latching. Removed upper rack and unit is not closing properly.5-1 door lock error ; ordrng 1 WPW10544004 (door latch strike) and 1 WPW10653840 (door latch)
Jesus C.
WASHER WHIRLPOOL WFW9550WWOO Customer states that unit is not working. Ran diagnostics and found several error codes. Ran auto tested and unit would not drain them afterwards would give error code F-01. After error code unit would not allow any selections. F-21. Long drainF-26. Door lock errorF-01; ordrng 1 W10251767 (CONTROL) and 1 WPW10253483 (latch) and 1 WPW10730972 (pump-water)
James G.
DISHWASHER GE PDF820SGJ0BB Replaced listed parts Tested ok PLEASE MAIL COPY OF RECEIPT PLEASE MAIL COPY OF RECEIPT
James G.
REFRIGERATOR GE ZISS420DXCSS Found drain tube from evaporator not in drain pan behind compressor. Properly routed and secured drain tube
Jesus C.
REFRIGERATOR KITCHENAID KFIV29PCMS Customer states that unit has ice build up on back wall. Checked unit and found ice build up behind icemaker housing. ; ordrng 1 W10878992 (cntrl-elec) and 2 W11085027 (switch)s and 1 W11199439 (CNTRL-ELECT) and 1 WPW10764668 (ice maker)
James G.
MICROWAVE WHIRLPOOL WOC75EC0HS00 Replaced listed part due to erratic operation Tested ok
James G.
WASHER MAYTAG MHW6000XG2 Cleared drain holes in bellow
James G.
DISHWASHER GE GDT625PGJ6BB Unit still not working. Tech line says correct part number for board is WD21x24250 which supersedes to WD 21X24498. Tech line says part number should not change however everywhere I look it changes to the 24498.Customer is contacting GE for replacement.
James G.
FREEZER GE GTS21FGKDWW "Replaced listed part, unit still not freezing bread or ice cream. All fans running and frost pattern is perfect."
Jesus C.
DRIYER WHIRLPOOL WGD8500DC4 Customer states that unit is leaking after when steam cycle is on. Checked unit and found the left side lower part of door not closing all the way. Ordering parts. ; ordrng 1 W10614960 (door) and 1 W10850024 (hinge) and 1 W10850044 (hinge)
James G.
WASHER GE GFW450SPM1DG "Replaced listed part and raised front for balance,Tested ok"
James M.
DISHWASHER KITCHENAID KDFE104DSS5
James M.
MICROWAVE WHIRLPOOL WOC75EC7HS00 Upon opening new parts. found edges of glass chipped and customer would like repaired.
James G.
WASHER MAYTAG MHW5500FW0 Replaced listed parts due to no drain and erratic operation Tested ok
James G.
WASHER MAYTAG MVWX655DW1 "Removed and replaced the drive hub. Found debris by the drain pump. Removed piece of metal from drain pump, Tested ok"
James G.
OVEN WHIRLPOOL WFG515S0ES1 "Right hinge not seated properly Removed and replaced the hinge, ajusted the door and tested ok"
James M.
REFRIGERATOR FRIGIDAIRE FFSS2614QP U it has water valve that leak a small amount after every ice fill causing ice blockage build up in ice tray. Ordering new water valve. Will return 9-12 to install. ; ordrng 1 242252702 (valve)
James M.
RANGE JENN-AIR JGRP536WP01
James G.
OVEN WHIRLPOOL KODE507ESS03 customer syayes there is a loud popping noise during preheat. Both ovens reached temperature with out any unusual noise.
James G.
REFIRGERATOR JENN-AIR JS48SSDUDE01 Replaced listed part
James M.
REFRIGERATOR WHIRLPOOL KRMF706ESS01 permagum gasket is needed to correct ice buildup. Ordered part; ordrng 1 W10688359 (sealer-gum)
James G.
DRYER WHIRLPOOL LCQ9508LW0 Reconnected ventTested ok
James G.
RANGE - ELECTRIC FRIGIDAIRE NOT AVAILABLE There is no model number available due to extreme build up of stuff under main top. I was able to get all four burners working (documented) however if problem persists unit will need to be replaced
James G.
FREEZER FRIGIDAIRE LFFH17F3QWC Replaced listed part Tested ok
James G.
STOVE GAGENAUL VG330811
Isidore A.
OVEN KITCHENAID KODC304ESS01 "Upon arrival, removed and replaced control. Test oven no codes. Test oven operation upper and lower at 350 degrees F., ok .Customer instruct on starting bake or broil cycle. Note; customer didn’t understand why temp would go to “lo” when pre heating"
Isidore A.
DISHWASHER KITCHENAID KDTM404EBL3 removed drain motor Found obstruction in drain motor reinstalled drain test ok at this time.
James G.
MICROWAVE GE PEB2060SM2SS Bad mag tube part number WB27X26081 no one at location to make decision or pay service call
James G.
WASHER FRIGIDAIRE FFLG3900UW0 Fill hose leak and lid switch buzzes; ordrng 1 137353302 (lock) and 1 137513710 (striker) and 1 5304488479 (clamp) and 1 5304508358 (fill hose)
Isidore A.
REFIRGERATOR WHIRLPOOL WRS321SDHZ01 Customer states refrigerator making noise, especially noticeable at night. Noises not verified. Found drier vibration hitting frame moved drier . Noise can be condenser fan noise or compressor noise.
Isidore A.
DRYER MAYTAG MGD8200FW0 "Removed top panel and old control board, installed new control board and test drier operation ok at this time"
James G.
WASHER GE GTW330ASK2WW Installed listed parts got unit to drain however no motor functions at all; rqstng P&A on 1 WH18X28176 (CONTROL ) and 1 WH49X25376 (1/3 hp motor and nut)
Isidore A.
MW OVEN COMBO KITCHENAID KOCE500ESS02 "Found display not working on microwave part of display. removed front panel, removed wire harness plug to panels found connector not properly inserted in terminal on board .Reinstalled connector and touch panel test microwave. Microwave working at this time."
James G.
CONVECTION OVEN GE n/a Erc failure ; ordrng 1 WB27T10204 (oven control erc3h)
Irvin F.
REFRIGERATOR WHIRLPOOL WRF535SMBW00 ICE IS MAKER BAIL ARM IS OUT OF POSITION. IM NOT MAKING ICE. The bail arm is hanging from rear holder. Inserted into arm into motor head. The bail arm is not moving. Bypassed motor the motor will not cycle or advance. Replaced IM. Bypassed door switch observed cycling and fill. All ops normal.
Irvin F.
DRYER MAYTAG MEDC465HW0 "CX say the unit is not heating, and making a loud noise. Powered the unit ran dryer, the noise is confirmed. The unit heats. Left roller is being shaved in operation. Installed dryer kit. Noises are normal. All ops normal. ; used 1 4392065 (DRYER REPAIR KIT) from stock"
Irvin F.
DISHWASHER KITCHENAID KDTE104ESS4 "Main door gasket on right side lower tub will not stay in place. CX says it pops out, and the door sticks. The gasket will not stay seated. Removed gasket, in stalled replacement. Test, good all ops normal."
James G.
REFRIGERATOR KITCHEN AID KUIS18PNZW0 No show confirmed
Isidore A.
DRYER WHIRLPOOL WGD92HEFW0 "Ordering touch panel W10919216 and control board W10875487 allow 2 hoursFound touch control not operating correctly in test mode, dryer working intermittent, parts ordered; ordrng 1 W10875487 (cntrl-elec) and 1 W10919216 (panel-cntl)"
Irvin F.
WASHER MAYTAG MVWC415EW2 "Installed replacement parts. Powered unit, ran calibration, passed. Unit is fully operable. All ops normal. ; used 1 W11124822 (CONTROL) from stock"
Irvin F.
WASHER HOTPOINT HTW200ASK1WW "CX says the washer will not start. Checked found couple errors, DOOR LOCK. TEST LOCK LED FAILED TO MOVE. Installed replacement lock ran test check, passed. All ops normal."
Irvin F.
DRYER MAYTAG MEDB835DC4 "CX reports odd noises from the unit. Removed and replaced the sensor. Hooked unit to power, checked errors none. observed during operation, unit is heating properly. All sounds are normal. Unit fully operational."
Isidore A.
DISHWASHER KITCHENAID KDFE104DWH4 Detergent door coming apart and upper rack adjuster broken rack falling. Detergent dispenser door W10888684 kit upper rack adjusters WPW10546503 parts ordered.; ordrng 1 W10888684 (cover) and 2 WPW10546503 (adjuster)s
Irvin F.
WASHER WHIRLPOOL WTW5000DW2 "The unit is dead. The main control has no 5dc LED. removed power, replaced control. Powered the unit, test components passed. Calibrated the unit, passed. All ops normal."
Isidore A.
WASHER WHIRLPOOL WFW85HEFC1 "No codes found, customer states user interface W10903217times out intermittently note needs 2nd man allow 2hours.; rqstng P&A on 1 W10903217 (panel-cntl)"
Irvin F.
REFRIGERATOR KITCHENAID KRMF706EBS01 "Replaced mullion. Test for operation, good. All ops normal. Done."
Isidore A.
DRYER WHIRLPOOL WGD9400SW0 "Found belt came off motor pulley broken ordering motor 279787, blower wheel WP697772 and dryer repair kit 4392067; rqstng P&A on 1 279787 (motor 124.38) and 1 4392067 (dryer repair kit) and 1 WP697772 (wheel 22.33)"
Irvin F.
FREEZER FRIGIDAIRE FFHT2032TP2 Noise issue. The fan blade is not rotating properly. The shaft is bouncing in the housing motor. Replaced motor and blade. Powered unit fan runs smooth and properly. All ops normal.
Isidore A.
DISHWASHER KITCHEN AID KUDC03IVBL0 Found water inlet valve W10648041 leaking. Customer unsure of having dishwasher repaired ; rqstng P&A on 1 W10648041 (valve-inlt 60.89)
Hector Z.
DISHWASHER MAYTAG MDB4949SHZ0 Customer Spence burning smell on the drying cycle. Set unit in diagnostic and found no error code. Ran the rest of the diagnostic test and it pass. The burning smell is coming from the heating element when it get energized. Tested ok.
Hector Z.
REFRIGERATOR KITCHENAID KBSD608EBS00 "Control panel not accepting commands. Checked unit and removed power for few minutes to reset the controls. Restart power, tested ok."
Hector Z.
RANGE MAYTAG MGR8700DS0 Replaced control. Tested ok.
Irvin F.
MICROWAVE KITCHENAID KEMS308SSS04 During operation of the microwave there is a buzzing pulsing noise.
Hector Z.
DRYER MAYTAG MGDB765FC0 Replaced door switch. Tested ok.
George Y.
WASHER MAYTAG MVWB955FW1 There should be pictures on first original job.
Irvin F.
REFRIGERATOR KITCHENAID KRMF706ESS01 In the FREZER section. The middle drawer on left side is catching the upper drawer rail. The middle drawer left roller is catching. Need to replace the bin. ; ordrng 1 W11122881 (bin-freezr)
Irvin F.
WASHER WHIRLPOOL WTW4950HW1 "Ordered part not ordered, tech issue. ; ordrng 1 W11256105 (CONTROL)"
George Y.
WASHER WHIRLPOOL WFW75HEFW0 "Found washer bellow came off reposition. Removed and replaced the bellow, retested check out ok, will no longer fall out of place, complete. No dents or dings cause by tech."
Irvin F.
REFIRGERATOR FRIGIDAIRE FFHS2611PFCA
Irvin F.
REFRIGERATOR WHIRLPOOL WRS315SDHZ00 The condenser motor is out. Compressor is hot drier is hot. The Fresno is too warm to cool. Need new con motor; ordrng 1 W10854034 (motor-cond)
George Y.
MICROWAVE JENN-AIR JMW2430WS02 Found oven with error f6e0 error turn power off rebooted retested check out ok complete. No dents or dings cause by tech.
George Y.
WASHER AMANA NTW4516FW2 Found washer working ok no leaks told customer to run more loads to give me a call if any signs of leaking complete.
George Y.
DRYER WHIRLPOOL WED9290FC0 Installed part tested check out ok complete. No dents or dings cause by tech.
Irvin F.
DRIYER GE GTD75ECSL0WS "Dryer is dead. He led power @ outlet supply is correctly wired. Checked connection at terminal block, good connection. Checked orange to white J101 getting power. Checked from J101 NEUT TO gas coils and relay coilsall receiving power. No voltage dc going to 8nferface. 7nit had bad contr9ol. ; ordrng 1 WE04X28084 (CONTROL)"
Irvin F.
DRYER WHIRLPOOL MDG8757AWW Noisy dryer. Scraping Front slides are completely worn. Needs replacement slides. ; ordrng 2 306508 (TUMBLER KIT)s
George Y.
COOKTOP JENN-AIR JES9800CAB01 Installed parts tested check out ok complete no dents or dings cause by tech.
Hector Z.
WASHER MAYTAG MHW5100DW0 Stuck detergent dispenser and slow cold water fill. Ordered both parts and rescheduled.; ordrng 1 W10575334 (DETERGENT DISPENSER ) and 1 W10599356 (WATER VALVE)
George Y.
WASHER WHIRLPOOL WTW4616FW2 Found washer working ok draining ok customer instruct possibility customer using too much soap not letting unit going into fast spin too much soap testing ok complete. No dents or dings cause by tech.
George Y.
DRYER WHIRLPOOL WED4616FW0 "Upon arrival, customer informed concern of long dry time. tested unit, thermal fuse was not making connection. Removed and replaced the fuse. tested unitn now function properly. Customer instruct unit and its functions. unit ops as design. No dents or dings cause by tech."
George Y.
MICROWAVE WHIRLPOOL WMH31017FS2 "Found microhood wen in used electrical smell order found capacitor swollen need to replace dial and capacitor ok to order parts.; ordrng 1 W10850446 (capacitor,HV) and 1 W11256462 (diode,HV)"
George Y.
OVEN JENN-AIR JMW3430WS02 Need to order hall sensor ok to order part customer ok.; ordrng 1 W10460457 (sensor)
George Y.
RANGE JENN-AIR JGRP548WP01 Front right burner has small tip tried to adjust still the same need to replace right front valve ok to order part.; ordrng 1 WPW10371235 (valve-brnr)
George Y.
COOKTOP JENN-AIR JES9800CAB01 Top was not order . Order top ok.; ordrng 1 W10239357 (cooktop)
George Y.
REFRIGERATOR WHIRLPOOL WRF757SDEM01 Found refrigerator not getting as cold found not a full frost pattern only upper part makes a rock of ice need to replace compressor and evaporator and dryer and ice maker ok to order parts near a seal tech for completion of job.; ordrng 1 W10832994 (compressor) and 1 WPW10608485 (evaporator)
George Y.
DISHWASHER WHIRLPOOL WDT750SAHZ0 Need stopper on right side of rail ok to order part.; ordrng 1 WPW10508950 (stop)
George Y.
WASHER WHIRLPOOL WET4027HW0 Board not in ok to reorder.per Robert reordering ok
George Y.
DISHWASHER MAYTAG MDBH955AWS Found washer when washing excessively loud bad sump pump customer did not want to go with repair do not order parts job complete.
Erick S.
REFRIGERATOR WHIRLPOOL WRT311FZDW "Found heater not engaging causing frost build up and no airflow torc. Defrosted all air channels, replaced bimetal. Retested it snd it now cooling in both sections with no errors, job complete"
Erick S.
WASHER AMANA NTW4516FW3 "Cycled unit and found units drain not to correct height level causing water fill error and unit not to advance. Secured drain hose to correct height. Reprogrammed main board and control. Retested it through tests cycle and it passed all, tests with no errors."
Erick S.
REFRIGERATOR HAIER HA10TG31SW Found unit not cooling in either compressor due to bad compressor. Compressor windings are out of range. Units compressor will need to be replaced. COMPRESSOR is not a serviceable part due to small refrigerator. Compressor to available to repalce.Job complete
Erick S.
WASHER MAYTAG MVWC465HW2 "Cycled unit and found it with shifter error. Accessed shifter and found belt uninstalled from motor causing failure. Reinstalled ,secured belt,motor and pulley. Retested it and it passed diagnostics with no errors. Job complete"
Erick S.
REFRIGERATOR WHIRLPOOL WRS325FDAW Cycled unit found cooling intermittently. Found bad thermostat causing error. Replaced thermostat. Unit is now cooling in both sections with no errors. If issue persists please order new defrost board.Job complete
Erick S.
WASHER AMANA NTW4516FW3 "Upon arrival, removed and replaced the control board. Cycled unit and found it not spinning. Found over loaded code. Reprogrammed main control. Retested it and it passed al, tests with no errors. Job complete"
Erick S.
DRYER GE DPGT650EHWW Installed new parts on unit. Retested unit with customer and it passed all tests with no noise or errors. Job complete
Erick S.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 "Cycled unit and found with an E2 error indicating motor out o position causing unit not to mask proper ice. Replaced ice maker ,retested,it cycled and filled with no errors. Job complete"
Erick S.
FREEZER WHIRLPOOL WRT541SZDW00 Found unit full of frost and blocking air channels causing unit not to cool. Defrosted ice. Found heater not turning due to bad bimetal. Replaced bimetal . Retested it and heater is turning on. Units is no cooling in both sections. Job complete
Erick S.
WASHER MAYTAG MVWC565FW "Cycled unit and found it off balance error causing unit tangled clothes. Ran unit through diagnostics testing and it passed all tests with no errors. Instructed customer on proper loading,soap usage, and additional functions. Unit tested normal ops. Job complete"
Erick S.
REFRIGERATOR FRIGIDAIRE FFHS2611LB Found unit with frozen fill tube causing unit not to make ice. Defrosted tube and cleared all obstruction. Retested ice maker and it cycled and filled with no errors. Job complete
Erick S.
WASHER MAYTAG MVWX655DW "Found unit leaking oil causing it to make noise. Job replaced gearcase,wash plate,hub,and actuator. Retested it snd it passed all tests with no errors. Job complete"
Erick S.
REFRIGERATOR WHIRLPOOL WRS325FDAW Cycled unit And found both compartments not lighting. Replaced lights and now they lighting. Found unit leaking due to clogged drain. Cleared drain . Unit is no longer leaking . Job complete
Erick S.
RANGE FRIGIDAIRE FGEW3065PF Installed new console on unit. Set clock on unit. Unit passed all tests with no errors. Job complete
Erick S.
WASHER GE GTW330ASKWW Upon arrival found control not sending any voltage to engage. Randomly while testing lid would lock with out any engagement. Did find belt ripped and stuck between shifter and pulley. Both will need to be repalced; ordrng 1 WH01X24697 (BELT) and 1 WH05X25036 (SHIFTER) and 1 WH18X28174 (CONTROL )
Erick S.
DRYER GE DPGT650EHWW Cycled unit and found it making noise with nothing side drum. Accessed unt snd found bad Bearing on roller causing noise and will need to be replaced; ordrng 1 WE03X10008 (roller assm)
Erick S.
DRYER WHIRLPOOL MGDB765FW0 Previous events states to replace burner assembly. Ordering part; ordrng 1 280119 (gas burner)
Erick S.
WASHER MAYTAG MVWB835DW1
Erick S.
UPRIGHT / CHEST FRIGIDAIRE LFFH20F3QW "Unit has leak at heat exchanger causing unit not to cool. Unit will need new heat exchanger and compressor replaced. Double seal system labor required for repair, ; ordrng 1 297217900 (heat exchanger) and 1 297414054 (compressor) and 1 WPW10143759 (dryer)"
Dane K.
DRYER WHIRLPOOL WGD75HEFW0 Cx has no pop and was not willing to pay for service. Actual goods issue date is 6/9/2016.
Dane K.
DRYER - ELECTRIC MAYTAG MEDB980BG 1Upon arrival the unit would not start. Found the unit giving an F for F4 fault code. Found the thermal fuse open. Removed and replaced thermal fuse and tested unit. Unit functions normal now; used 1 WP3390719 () from stock
Dane K.
MW OVEN COMBO GE JKP90DP1WW Upon arrival microwave portion was dead. Remove microwave from oven and cavity and found thermostat open. Removed and replaced thermostat and tested and reinstalled microwave onto oven in cavity. Tested unit unit functions normal now
Dane K.
WASHER MAYTAG MVWC555DW Upon arrival the unit would not wash. Found the wash plate striped. Removed and replaced washplate and calibrated and tested unit. Unit functions normal now
Dane K.
BUILT IN MICRO WHIRLPOOL WMH32519FS Removed and replaced 20 amp fuse and interlock kit and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR KITCHEN AID KRMF706ESS Removed freezer led and found a loose connection causing dim light in fresh side and no light in freezer. Secured connection and tested unit. Unit functions normal now.
Dane K.
REFRIGERATOR ELECTROLUX EW23BC85KS "Removed and replaced icemaker, fill tube and installed fill tube insulation. Unit functions normal now."
Dane K.
WASHER GE GTW460A Upon arrival the cx stated unit was unit not filling. Found water valve not opening. Removed and replaced valve and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR GE GFE29HSDSS Removed and replaced main control and user interface and tested unit. Unit functions normal now
Dane K.
FREEZER WHIRLPOOL WRX986SIHV Upon arrival the freezer LED would not work and the fresh side LEDs on the top. Damn. Removed and replaced freezer LED assembly and tested unit. Unit functions normal now
Dane K.
WASHER GE GTW330ASKWW Removed and replaced transmission and agitator and tested unit. Unit functions normal now
Dane K.
DISHWASHER MAYTAG MDB4949SDZ0
Dane K.
DISHWASHER WHIRLPOOL WDTA50SAHZ0 cx states that the unit ran over night. Filled the unit up with water and found the water ice cold. Instructed customer on proper use and care of unit. Tested all functions of unit three times. Unit functions normal
Dane K.
WASHER MAYTAG MVWC415EW0 Upon arrival unit was making a rattling noise in the spin cycle. Found the impeller blade inside the drain pump was broken. Removed and replaced drain pump and tested unit. Unit functions normal now; used 1 WPW10661045 (PUMP-WATER) from stock
Dane K.
REFIRGERATOR FRIGIDAIRE KSRT25CRMS01 Tech support and went through trouble shooting steps; ordrng 1 8201672 (cntrl-elec)
Dane K.
OVEN ELECTROLUX EW30EW65GS "Remove and replace control board. Code returned. Uninstalled oven and took on reading off of temperature sensor. Wires and temperature sensor were not making good connection. Unit needs new harness and new sensor; ordrng 1 318572779 (harness) and 1 5304504897 (sensor)"
Dane K.
MICROWAVE GE JKP90DP1BB "Upon arrival the microwave screen was blank and there was no light inside the microwave. Found the thermostat open. Removed and replaced thermostat and tested unit. Unit functions normal now; ordrng 1 WB24X10034 (fan tco (60/70)), used 1 WB24X10034 (FUSE) from stock"
Dane K.
DRYER - GAS ELECTROLUX EIMGD60LT3 Unit had open limiter and shorted igniter. Unjt needs new igniter and and limiter.; rqstng P&A on 1 134711401 (limiter) and 1 137524000 (igniter)
Dane K.
WASHER MAYTAG MVWB765FW Upon rival the lid and hands were broken. Unit needs new lid and hinge; ordrng 1 W11259006 (LID)
Chris M.
REFRIGERATOR WHIRLPOOL KSSC36QMS02 On return visit replaced ice dispenser motor shaft and all other Parts listed for the ice dispenser assembly. Then reinstalled ice container and checked for proper function customer can I’ll get crushed and cubed ice from door.Job complete
Chris M.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 Customer had noise concerns regarding the refrigerator also icemaker was not functioning properly and water dispenser calibration was off. Found Bella I’m on ice maker not inserted properly Reinserted bail arm Icemaker is now functioning properly. As far as the water dispenser just needed calibration so I went ahead and did that. And as far as the noise customer is experiencing all fans compressors everything sounds normal. Refrigerator is kind a built-in to a cabinet so the noise of the compressor And condenser fan is echoing.
Chris M.
REFRIGERATOR WHIRLPOOL WRS571CIDM02 On return visit removed and reinstalled icemaker. Went through diagnostics checked for proper function everything checks out good. Job completed
Chris M.
DRIYER ELECTROLUX EIMED60LT4 Customers issue dryer would shut off/E 64 code. I remove front door to access heater and all other Components. Found black wire heading to heater was melted and broke off. Proceeded to cut wire back and put a fresh connector on there and also replaced heater. Reassembled Dryer all functions tested good. Job completed
Chris M.
WASH/DRY COMBO GE DSKP333EC5WW upon arrival removed and replaced timer. Reassembled dryer tested for proper function everything checks out good. Job completed
Chris M.
WASHER MAYTAG MVWX655DW1 Upon arrival removed to replaced control board Water valve housing And also lid latch. Then calibrated unit and ran system test. All functions are testing normal. Leaving washer and clean mode customer added affresh . Customer is going to monitor wash cycle to see if it completes.
Chris M.
REFRIGERATOR WHIRLPOOL WRX988SIBM01 upon arrival removed all shelving and drawers. Deiced evaporator In refrigerator compartment. Removed and replaced fan motor and thermistor. Also replace control board and you ui panel.Reassembled refrigerator set the proper settings everything is functioning properly now job complete
Chris M.
COOKTOP WHIRLPOOL W5CE3024XB00 Upon arrival removed cooktop replaced and installed new glass. Tested for proper function and wiped all fingerprints off job completed
Chris M.
REFRIGERATOR KITCHENAID KBBL306ESS01
Chase F.
WASHER WHIRLPOOL WTW5000DW1 "Installed new motor and drive belt. Calibrated unit, unit now running complete cycle and working by design."
Chase F.
REFRIGERATOR WHIRLPOOL WRF954CIHZ00 "Installed new valve and filter cover. Also did a defrost job on RC evap, cleared drain plug with steamer and removed ice. Unit tested ok. Now working by design."
Chris M.
DRYER MAYTAG MEDX655DW1 cx states dryer is not functioning. Found door switch to be broken ordering doors switch; ordrng 2 WPW10569603 (switch-dor)s
Chase F.
REFRIGERATOR FRIGIDAIRE LGHD2369TF1 I stalled both ice makers. All other specs tested ok. Unit now running complete cycles. And working by design.
Chris M.
COOKTOP KITCHENAID KICU509XSS00 Upon arrival I replaced both front and back right side elements. Also replaced fuse that blew I ended up going through three of my fuses. I powered unit on enter the required information. Unit started to function on the left side again and then all of a sudden blew the fuse and now nothing works; used 3 W10138793 (FUSE) from stock
Chris M.
REFRIGERATOR KITCHENAID WRV986FDEM01 Customer is having temperature concerns in the refrigerator compartment. I toggle through diagnostics found fan for icebox not functioning also dampener is not opening and closing all the way.Also ordering a more accurate thermistor; ordrng 1 W10846539 (evaporator fan blade) and 1 W10902214 (thermistor) and 1 WPW10248595 (control)
Chase F.
WASHER WHIRLPOOL WTW8540BW0 "Installed new bearings, calibrated unit. Ran unit through test cycles. Unit now running complete cycle and working by design."
Chris M.
REFRIGERATOR WHIRLPOOL WRF555SDFZ00 Cx states icemaker is not producing ice. Found icemaker have a broken gear
Chase F.
REFRIGERATOR WHIRLPOOL WRT311FZDW01 Found drain line frozen up. Cleared blockage with steamer. Unit now getting proper air flow. And now working by design.
Chris M.
DISHWASHER WHIRLPOOL WDF330PAHB0 Customers states Dishwasher quit functioning. Upon arrival and after running diagnostics found pump motor to be bad also fill valve is not opening; ordrng 1 W10872255 (valve)
Chase F.
DRYER WHIRLPOOL MGDB955FC0 "Diagnosed a whirlpool dryer, received an F4e3 error code indicating restricted air flow. Confirmed that airflow system is not blocked, checked lint screen and exhaust duct. Everything is clear and blowing through with no problems, cleared error code. Checked all other specs, and unit is running a complete cycle and heating with no problems. Unit working by design."
Chris M.
WASHER MAYTAG MVWX655DW1
Chase F.
WASHER MAYTAG MHW6630HW0 "Diagnosed a Maytag washer, received an F8E1 error code indicating a valve failure. Ran unit through manual test mode to check that valves are working properly. Valves are working properly. Cleared error code. Ran unit through calibrations. Unit is now calibrated with no error codes, running a complete cycle, and working by design."
Chase F.
RANGE WHIRLPOOL WFG515S0ES1 "Installed new parts. Unit now lighting with no problems and working by design, all other specs tested ok."
Chase F.
WASHER GE GTW220ACKWW
Chase F.
WASHER GE GTWN4250DWS Installed new magnet assembly. Unit started right up. Now running complete cycle and working by design.
Chris M.
WASHER MAYTAG MHW5500FC1
Chase F.
REFRIGERATOR WHIRLPOOL WRX735SDHZ01 Installed new ice maker. Unit now working by design. All other specs tested ok.
Chase F.
REFRIGERATOR WHIRLPOOL WSF26C2EXW01 Installed new diffuser. Unit now getting proper air flow. Unit now running complete cycle and working by design. All other specs tested good.
Chase F.
WASHER GE GTW330ASK4WW Installed new lid lock. Unit now draining with no problems. Running a complete cycle. And working by design.
Chris M.
COOKTOP KITCHENAID KICU509XSS00
Chase F.
WASHER WHIRLPOOL WTW4855HW0 "Diagnosed a whirlpool washer, received an F2E1 error code indicating a stuck key, ran through key activation test and unit passed test with no problems. No stuck buttons, cleared the error code. Ran unit through a calibrations cycle. Ran through automatic test cycle and unit passed all cycles with no problems. Unit now calibrated and working by design."
Cesar H.
DRYER MAYTAG MGD3500FW0 Found worn idler pulley installed dryer kit unit tested good
Chase F.
REFRIGERATOR FRIGIDAIRE FFHB2740PPAA "Diagnosed a refrigerator, found ice frozen up to motor evap fan. Ordering parts for repair. ; ordrng 1 5303918784 (air handler housin) and 1 5304493604 (fan & gasket kit)"
Cesar H.
WASHER WHIRLPOOL WTW5000DW0 Replaced part ordered by previous tech. During repair I noticed capacitor had expanded indicating failure replaced cap as well calibrated and tested all checked good
Chase F.
WASHER MAYTAG MVWX655DW0 "Found a bad gear case seized up. Needs new transmission and hub. Ordering parts.
Chase F.
DRYER MAYTAG MGD6630HW0 "Installed new ignitor. Repaired broken wire harness. Needs new board, shorted out to the relay. Ordering new board. Part is not listed as Available in marcone please EXPART .; ordrng 1 W11170772 (CONTROL ACU)"
Cesar H.
DRYER MAYTAG MGDB765FW0 "Unit will not always start when start is pressed and turns off mid cycle before finishing. checked unit found communication error between UI and motor control removed console and found wire harness connector between ui and control not fully seated at main control connection is damged on the harnes, when unit start vibrations cause loss of communication. Removed and replaced the harnes and tested, all tested good"
Cesar H.
REFRIGERATOR WHIRLPOOL WRF535SMBM00 Installed shims on components to make things fit all checked good
Cesar H.
DRYER ROPER RGD4516FW0 No heat tested units components found thermal fuse ohms open. Replaced failed fuse all tested good ; used 1 WP3392519 (THERMAL FUSE) from stock
Cesar H.
OVEN KITCHENAID KOCE507ESS06 Microwave door not engaging right hand door switches door looks be closing fine I find the problem to be in the switch and switch holder. Replaced switch assembly unit tested good
Cesar H.
WASHER WHIRLPOOL WTW8100BW0 Replaced latch and console tested good
Chase F.
WASHER AMANA NTW4605EW0 Diagnosed an Amana washer and found that the agitator is seized up to the gear case. Ordering parts for transmission repair, need to remove basket and tub. ; ordrng 1 W10908289 (agitator) and 1 W11255272 (GEARCASE)
Cesar H.
DISHWASHER BOSCH SHX84AYD5N-01 Replaced lock checked good
Cesar H.
WASHER WHIRLPOOL WTW5000DW1 Found failed shifter not able to find position unit will not run do to error also found screws holding belt cover stripped routed for screws and shifter ; ordrng 1 W10913953 (actuator) and 2 WP22001995 (screw)s
Cesar H.
RANGE WHIRLPOOL KFGG500ESS2 When oven gets hot and it’s time to relight the clicking of the spark can be heard and and the gas valve is open but gas fails to light when unit is cold it will light every time routed for ignition components ; ordrng 1 W10764654 (burnr-oven) and 1 WPW10324262 (igntr-oven) and 1 WPW10511278 (module-spk)
Billy J.
REFRIGERATOR WHIRLPOOL WRF535SWHZ00 Removed and replaced ripped gasket retested job complete
Cesar H.
WASHER WHIRLPOOL WTW5000DW1 Failed wash plate splines on wash plate that engages drive are stripped shaft turn but wash plate doesn’t move. Found pump slow to drain water out and long drain codes in unit. Inspected pump found missing fins on the pump; ordrng 1 W10752283 (washplate) and 1 W10876600 (drain pump)
Billy J.
REFIRGERATOR WHIRLPOOL WRF535SWHW00 Upon arrival removed and replaced both freezer rails lowered legs retested job complete
Billy J.
WASHER AMANA NTW4516FW2 Upon arrival cx stated unit not operating found unit had long fill found unit has defective hot water valve removed and replaced retested job complete
Billy J.
WASHER MAYTAG MVWB835DW3
Cesar H.
REFRIGERATOR GE GSHS3KGZBCSS Unit leaking found 2 Broken water lines one to the door and one coming in to water tank routed for parts to correct the problem ; ordrng 1 WR17X11440 (water tank assm) and 1 WR17X2891 (plastic tube)
Billy J.
WASHER AMANA NTW4516FW2 Upon arrival unit was completly dead but had correct power. removed and replaced main contro,l recalibrated and tested job complete
Billy J.
DRYER WHIRLPOOL WGD8500DW0 Upon arrival cx states unit has been working since I left still advised the control needed to be replaced unit so intermittent not even techline knew what it could be removed and replaced control retested job complete unit heating as designed
Cesar H.
DISHWASHER FRIGIDAIRE FFBD2406NS9B Failed door latch not recognizing door closed.burnt switch on latch rerouted for latch ; ordrng 1 5304517278 (LATCH )
Billy J.
MICROWAVE WHIRLPOOL WMH32519HZ-1 Removed and replaced capacitor and magnetron cap blew up and was all melted retested job complete unit now working as designed and heating as designed job complete
Billy J.
REFRIGERATOR IKEA IRS335SDHM00 Upon arrival found diffuser door was jammed open and defective removed and replaced retested job complete
Billy J.
DISHWASHER WHIRLPOOL KDFE104HPS0 Upon arrival unit is completly dead. cx states this is the 4th time this happened to their dishwasher in ten years. unit found there was no voltage at control inspected main box and hot wire came out of wire but resecured retested job complete
Billy J.
WASHER WHIRLPOOL WTW8500DW5
Cesar H.
DISHWASHER MAYTAG MDB4949SHZ0 "Customer instruct water supply to dishwasher was not opened all the way. Ran test on unit found wash motor grinding pretty loud, ; ordrng 1 WPW10591570 (pump&motor)"
Billy J.
WASHER MAYTAG MVWB835DW1 W11165546 removed and replaced valve retested job complete
Billy J.
REFRIGERATOR WHIRLPOOL WRX988SIBB00