"On arrival Cx states unit has a low bail arm and cant remove bucket. No ice, found loose connection at ice bucket detection switch, secured and tested, unit functions as designed."

"Found unit not connecting to Wi-Fi. Checked unit. Unit is operating as designed. Cx network is not the right one. Cx is suppose to have unit connected to 2.4 ghz network. Cx has some different internet. Only has one network available to choose from. Called techline, they said that I reached them after hours at 10 am. Referred client to internet provider. Issue is with servicer. All ops normal. Unit ok. Job complete."

"Found loose connection on fitting for water supply to door, hose not fully seated on fitting causing a small leak when dispenser is used, fully seated hose in fitting and all tested good"

"Installed control and console. Tested, unit functions as designed."

Replaced control. Tested unit all functions are working properly. Job complete

"On arrival Cx statess no hot water. Found loose connection at hot water valve. Tested, unit functions as designed."

Installed parts tested check out ok complete no dents or dings cause by tech

Removed and replaced motor and ice container. Tested unit. All ops checked good

Replaced broken lower spray arm unit ok after repair. Spray arm not turns smoothly.

"The customer received the fresh food compartment door by mail, upon inspecting the door, found it arrived damaged, dented on the upper right corner. Checked the door on the unit, and found the unit was not leveled properly, the gasket was deformed because it was not on properly. Removed the door gasket from the new door, and installed it on the units door, applied heat to the gasket to de wrinkle, and shape properly. The customer reports the unit freezes in certain areas in the fresh food compartment. Found the customer is blocking airways, by pushing the items against the rear wall, pointed that out and advised the customer not to block the airways to prevent cold spots, leading to food freezing. The customer does not agree that by blocking airways some items will freeze, she claims its not the first refrigerator she owns. Called the technical department, and documented issues and findings. SR 7735680884; used 1 W10838574 (Gasket FF) from stock"

Tested found dispensor not opening properly replaced tested working to spec; used 1 W11412300 (Dispensor) from stock

Replaced the shorted heating element and open thermal fuse. Tested after repair all ok.

"Unit making loud noise and not agitating or spinning. I tested unit and found that the actuator didnt fully engage and damaged cam assy. Removed and replaced actuator and cam. Tested unit. All tests good. ; used 1 W10913953 (ACTUATOR), and 1 W10721967 (Cam) from stock"

Cx issue is they were getting long dry times Installers installed a extremely long exhaust hose and then smashed it up so it could not vent properly I instructed cx to purchase a shorter hose and to make sure its not smashed cause the unit needs to vent properly in order to dry correctly Complete

Installed new console and appliance controller and tested unit working as designed

"Found basket engagement error codes f7 e4/f7 e3. Found issue with shifter, removed and replaced shifter, tested ops unit working as designed.; used 1 W11481722 (Actuator) from stock"

Replaced part and tested unit

Upon arrival cx stated oven has not been heating properly since thanksgiving. Found burner sleeve was very open creating too much gas pressure making which is causing the flame to extinguish itself. Adjusted sleeve and retested. Flame now connecting with burner properly. All other ops test normal at this time. Job complete.

Found unit not spinning found unit getting excessive suds. Removed the built up suds from inside unit and tested. Unit is working properly. Recalibrated unit and tested. Unit coded out speed basket error. Replaced actuator and tested. Unit is working properly.

cycle unit and found door hinge screw coming of right top corner. Secured door screws unit door now closing as designed

Cycled unit and found loose agitator causing unit to fail. Secured agitator and retested unit passed all tests at time of service job completed

Found unit not spinning. Found unit with a worn drive hub. Replaced hub and agitator. Had to break agitator to replace hub. Tested unit. Found unit not agitating. Replaced actuator wi5 old style actuator and tested unit. Unit is working properly. Customer approves function at this time. ; used 1 W10528947 ( Hub) from stock

Replaced gasket all tested good

Installed new parts and retested unit passed all tests at time of service. Job completed

Installed latch and ran diagnostic tests. Unit passed all tests. Job complete

Installed new water valve and control board retes unit passed all tests at time of service job completed

"Installed parts, tested, unit functions as designed."

Customer getting off balance load codes. I tested unit and found that the rotor bolt came loose and gave false code. I tightened rotor and tested with load of towels. All tests good.

Replaced selected part Unit working properly as designed

This Whirlpool commercial washer is not at this location.

Found no mechanical problem with unit at this time Run unit thru diagnostic all okNo error fault codes register Customer education on how to use and what to spect from unit

"Found unit making rattling sounds when heating, disassembled unit , checked diode and mag , found micro switch interlocks pushed in, reset interlock, Replaced fuse, unit operating as designed, found ducting open in cabinet, retapped duct work found open."

Installed new ui count roll and unit is working per design.

Replaced both water valves. Tested cold and hot water line. Both lines now filling at correct water pressure.

"Replaced the compressor , recharged the unit , tested ok now at this time"

"Removed and replaced motor, cam and belt. Tested unit with load. All tests good."

"Found hood working okWhen customer cooks bacon it smokes the house, unfortunately this unit will not suck all smoke out"

Customer stated unit has frost font refer door sits low added spacer and tested customer to defrost to start over tested all works good at this time.

"F7E9, Found loud gearcase bearing, gave estimate for gearcase replacement, replaced gearcase,, ran recalibration cycle, ran self diagnostic cycle, unit sounds & operates as designed."

Cx states that unit is not dispensing water Remove and install new filter Cx provided Tested unit working properly as designed

"Checked fridges functions, doors and their gaskets. Fridge meets factory specs. Nothing wrong with unit"

Replaced all selected parts Unit working properly as designed Not dispensing water water tub frozen Cx will defrost unit If cx again complaint regarding same issue please schedule next visit with Andrew confirmed

Called TAG and was told to dispense water about six times with the bypass filter to see if the unit will let you. If it is possible then the filter is the issue. Asked TAG about the set temperature and product temperatures I was seeing. The set temp is 38f and the product temp is ranging from 39f-42f. TAG says this is in range and that the product can range from -/+5F. Unit is operating as designed.

Replaced parts and tested unit

"Replaced motor pulley, belt, belt pulley, and support rollers. Checked units ops, the unit is now working as designed. Need to send invoice to collect for the repair."

Installed new valve and tested unit. Unit working as intend.

"Sealed system leak repair, found sealed system leak at between heat exchanger and dryer, replaced dryer and recharged unit all tested good ; used 1 WPW10143759 (Dryer) from stock"

Installed new blower wheel. Was able to salvage the motor. Returning new one. Unit is now operating as designed. Complete.

Installed part tested check out ok complete no dents or dings cause by tech.

Joe with tech line. The unit is filed under as unrepairable and do to how many parts plus compressor. Unit is still now working. File number sr 7734822634. Aug needs to be contacted and go from there. Unit is going through ext warranty. Sr number 7735570708 866-931-7390. 10 to 6 east coast time. Called aug and have a new claim number and customer is going to call in 2 to 3 days to see what happened.

Install the new door switch on the unit. Retest the unit and unit is working properly. Job complete

Replaced electrode all tested good

"Replaced all parts in the dryer repair kit, in order to fix loud clanking noise. Tested after repair all ok."

Installed gearcase tested no leaks working to spec

Customer stated that the other company came out and installed the ice level boards and that the icemaker began to function. No diagnosis was performed or given.

Installed the new motor on housing dryer OK; used 1 W10847984 (Switch) from stock

Replaced suspension kit Unit working properly as designed

Installed new Evap motor Previous one did seem to have any malfunctions once I got it pulled out but installed new one and cx was satesfied Complete

Installed new parts. Operation tested as designed. No gas leaks.

Found thermal fuse popped replaced tested working to spec; used 1 Wp339259 (Thermal fuse) from stock

Unit has shorted key on control. F2e1. Part Is discontinued. Contacted TECHLINE. Nate sr. 7735677252 directed customer to contact customer disservice for further actions.

Installed float. Standpipe and valve. Tested unit. Unit is working properly. Customer approves function at this time.

"Replaced the icemaker , tested operations ok now at this time"

Customer stated that the lid broke at the hinge. Removed and replaced lid tested all works good at this time.

Timer shaft was pulled out of timer. Due to a faulty timer color. Removed and replaced timer. Tested unit and it functions normally

Customer concerns. Freezer building up frost around upper right corner. Not sealing. I re-installed door gasket and adjust/leveled the refrigerator. Operation tested normal at time of service.

"Found loose wire on water valve, plugged in and tested unit working as designed"

"Installed temperature sensor and tested unit working as designed,advised customer to give it 24 hours to get to temperature"

Inspected unit and found failed capacitor. Replaced and unit passed all tests. Job complete

Installed part tested check out okcomplete no dents or dings cause by tech.

Installed control and latch. Tested unit. Unit is working properly. Customer approves function at this time. Passed auto test and recalibration.

Installed actuator and control. Tested unit. Unit is working properly. Unit passed both recalibration and auto test mode. Customer approves function.

"Found freezer defrost drain clogged Removed freezer drawer and rear panelUsed steam machine to clear drain and all ice around itReinstalled rear freezer panel and drawer, all ok now"

JB out 2/7/23. Install replacement HMI user interface assembly. Tested operation. OK. Reassembled unit and tested operation with customer. Unit now operates as designed. Tag both nameplate and appliance control. Unit as return and sent back not needed. No charge a customer. Job complete.

Upon arrival cx stated unit is not heating properly. The thermostat they have inside it is usually 100 degrees off. Ran unit through bake cycle and unit heated to 350. Cycled unit multiple times and it heated back up with no issues every time. Unit is operating as designed. Informed cx to allow 30-45 minutes for a proper preheat to allow everything inside to heat up to the desired temperature. Also informed cx that the metal thermostats they have are typically not very accurate and get more inaccurate as it heats up and cools down over time. Job complete.

Installed new pump and unit is now fully operational. Tested all components and everything checked out.

JB OUT 2/7/23. Customer states dryer runs but does not produce any heat. Upon arrival tested dryer verified no heat. Installed General Electric diagnostic smart HQ device. Verified no rise in temperature during heat circuit test. Tested outlet verified 120 VAC on L1 0 VAC on L2. Found and reset on tripped circuit breaker. Verified 240 V now available. Ran dryer. Found no increase in temperature. Tested outlet again. Tested 0 VAC on L2. Reset circuit breaker. Second time verified 240 V available and tested for proper ground. Unit is now operating verified increase in temperature when tested in time to dry cycle. Advise customer if heat function fails again to contact a qualified electrician to investigate the potentially failed circuit breaker. Circuit breaker is not physically tripping but not delivering volt 120 VAC to L2 leg of outlet. Advise customer of one time courtesy no charge on a no defect found service call visit under the manufactures warranty. Period. Tag pre I.D.d part heater and housing assembly part number WE11X21156 as returned and sent back not needed. No charge the customer. Job complete.

Installed components and unit is now working as intended.

Bob file number 86108338. Installed all new parts and recharged system. Unit was beginning to cool when I left.

Leak from drain hose pump to rear wall clamp came loose. Tightened clamp all tested good

Cycled unit and found clogged Waterville filter causing water restriction. Cleared filter and re-tested unit all test pass. Job completed.

Failed oven ignitor has 120v to it and will not come on. Replaced failed ignitor all tested good

Customer concerned that the burner caps and head fall off the cooktop when cleaning. Informed customer normal operations. And that the cap and burner heads are made for easy removal so cleaning the cooktop is much easier. Instructed on how to remove and install burner heads and caps.

Drain cap was loose causing unit to leak I tightened cap and unit began functioning as designed job complete

"JB out 2/7/23. Customer stated freezer temperature increased per the digital display. Upon arrival found all foods removed. Verified freezer is freezing properly at this time. Digital display indicated that a power loss had occurred. Reset digital alarm. Verified unit is set for Fahrenheit units. Unable to verify mechanical failure at this time (after resetting the power indicator alarm). No,parts used. No charge to customer. Job complete."

"Found .2 run cap, Replaced run cap, ran self diagnostic cycle,unit operating as designed."

Replaced inlet valve and ran cycle. Unit passed all tests and is operating as designed.

Replaced hinge all tested good

Installed module-spk DSI. Operation tested as designed.

Replaced parts and tested unit

Found fault code f8-e4 again Replaced drain pump

"JB out 2/7/23. Install replacement icemaker assembly part number 241642534. Cycled icemaker and verified water. Fill operation. Also verified proper operation of icemaker, feeler arm. No charge to customer. JOB COMPLETE"

"Replaced drain pump, tested fill, drain & spin functions, unit operating as designed"

Replaced element tested unit dryer is getting hot and all functions are working properly job complete

Cycled unit and found thermostat has failed. Installed new thermostat and re-tested unit all test pass. Job completed.

Installed part tested check out ok complete no dents or dings cause by tech.

Installed new door. Unit complete.

Customer stated unit is loud found suspension is worn out and Gear case is loud also dryer making noise. Quoted customer for gear case suspension and dryer repair kit. Customer declined collected service call.

Cx states that unit is making noise during spinning After running diagnostic test find that unit has a bad shifter Replaced all selected parts Unit working properly as designed

Replaced shorted heating element. Tested after repair all ok.