Ice maker not producing ice. The will buy new unit.

"Customer concerns: washer does not stop washing ( re-start by itself). Installed central electric. Performed calibration. Operation tested as designed. No leaks. I was unable to document with techline ( waited 30 minutes on hold, no answer). different issue from last visit."

"Checked for error codes. No error codes present. Drain pump is operational. Upon inspection, found drain hose installed without a high loop. Installed high loop. Tested u it. Unit operating as designed."

Removed rear panel. Burner assembly support bracket was misaligned. Adjusted bracket. Tested unit. Unit operating as designed. Job complete.

Replaced and shaped gasket. Tested unit. Unit operating as designed. Job complete.

Replaced thermistor kit assmbly. Retested it and unit is properly cooling. Job com

"Remove replace compressor. Pulled vacuum, recharged system. Inspected for leaks, unit is now cooling."

Found unit with low amp draw indicating low charge or leak. Replaced unit filter dryer assembly. Pulled vacuum. Inspected for leaks and found none. Recharge system. Inspected for leaks and unit held pressure. Unit passed all test. Job complete.; used 1 Wpw10143759 (Drier) from stock

Installed a new damper on the unit. Retest the unit and now unit doesnt have the noise anymore. Additional customer want me to apply the brakes on the on the unit. Job complete.

"Upon arrival check the unit and found unit has a bad igniter causing the failure. Replaced the igniter on the bake burner and now unit is working properly. Job complete ; used 1 12400035 (IGNITER,OVEN) from stock"

"Removed air gap it is clear, removed and replaced inlet, tested ops unit working as designed. Asked cx to test and report any issues."

"Oven bottom latch is having intermittent issues, light wont turn on, verified in diagnostics that the board will turn off the light. Customer has to turn off breaker so the light is not on. Latch assembly # W10883049 Customer wants to contact customer service to request repair cost assistance. Customer feels there may be intermittent issues with the control boards. Ran the top oven, top oven reached 350 degrees, lower oven would not heat, can be due to the latch failure. Will document with techline asap."

Installed parts tested check out ok complete no dents or dings cause by tech.

Installed part tested check out ok complete no dents or dings cause by tech.

White to red and then white to blue 12 volts. Fan replacement issue. Possibly a fan issue. Garret tech line. Checked out harness to fan. Brown and orange wire was not plugged in all the way not sure why or how but pin was sticking out of the brown wire not in all the way. Connection made and fan is now working correctly. Tested and checked out. Job completed. Wire in fan was the issue.

Found refrigerator control not responding replaced control retested check out ok complete no dents or dings cause by tech.

Installed part tested check out ok complete no dents or dings cause bytech.paid with I wallet.

Reworded lower heat element and replaced high limit produced ok note told customer to have vent cleaned before using dryer took picture of blower housing full of limit customer cleaned housing complete

Installed new drain pump all tested ok complete

Replaced water valve part#w11165546 product tested ok complete truck stock part#w11165546

Installed new auger motor and coupler also replaced ice container put so old ice in container no noise tested ok complete

"Replaced belt, and inlet valve. Assembled unit restored power, ran calibration cycle. Passed. All ops normal."

CX says the unit is making a noise. Confirmed the noise. The cam and belt is making the noise. Removed power replaced components. Restored power ran calibration cycle passed. All ops normal.

"The freezer door allowing in ambient air. Causing frosting. Installed gasket correctly into the unit, allowing gasket to form properly. Unit is sealing properly."

"M17S6Z0APL1-concessionF2/E1-STUCK KEY, F9/E1-LONG DRAIN, CLEARED ERROR CODES. Found drain motor was blocked with debri. Cleared out, ran calibration cycle passed. All ops normal."

"CX says the washer lock is clicking and unit is not operating. Found error code for stuck key. Cleared code, ran test cycle. The latch not operating properly. Replaced latch. Restored power, test passed. All ops good."

No answer at the door. Took photo. Office called CX. CX called house. Door opened. CX says the washer is not completing cycles. F9/E1 LONG DRAIN. TEST drain in components test failed. The 7nit needs replacement drain motor.

"Installed and secured parts listed,unit is now operating properly as designed at this time of service"

"Installed and secured parts listed, calibrated unit, ran diagnostics test, unit is now agitating and spinning properly as designed, customer approved repairs ; used 1 W11239857 (Belt), and 1 W10721967 (Cam kit) from stock"

Running a diagnostics test to see whats going on. Running test smart hq. Over suds. F31 out of balance l f27 water acc. Low. Suds f29. F19 ui state times out. Unit needs to be cleaned out. A lot of suds. Ill call tech line and ask them about there bleach section. But unit is now ran a full diagnostics test and calibration test. Customer is running a clean cycle and should be able to be back up and going. Passed all the tests on smart hq. No more codes. Job completed

Replaced parts needed. Checked out and ran a full diagnostics test. Unit is now working as designed. Ran one more test and fills washes spins and drains. Job completed.

Replaced parts needed. Tested and unit is now working as designed. All the burners are working correctly. Job completed

Replaced part listed and unit is sealed now. Customer should not have any ice build up or frost. Job completed.

Ran a full diagnostics test and lid lock showed up and f71 and f82. Customer is doing a clean cycle. Ran test and sud showed up. Unit passed and working correctly now. Drain was being blocked and checked out. Unit drains correctly now. no parts needed.

New display control is better and working as designed. Customer tried it and functions are working correctly. Job completed

"Note: On First visit was drum replaced, because it was pealing insideTHIS TIME Found the left hand wheels rubber damaged. Installed a repair kit"

Had user interface replaced. Fridge ok

Installed the new icemaker on this one cycle properly

Removed debris from drain pump. Washer tested ok

"Replaced defective, board and right rear base and igniter.Tested ok"

Installed heavier springs on door.

Replaced defective start device on compressor.Tested ok

Replaced defective turntable motor.Tested ok

Replaced right front valve and igniter harness.Tested ok

Reset lower switch hook.Tested ok

Installed new tub ring and unit is now complete.

Installed new ice maker and unit filled right away. Unit complete

Installed new suspension unit complete.

"Cycled unit and found broken strike. Installed new strike, and re-tested unit now working as Designed job completed; used 1 W11457841 (Strike) from stock"

Cycled unit and found different issue. This is not a recall. Icemaker not working. Ran diagnostics on icemaker and found fill tube is frozen. Cleared fill two and rent icemaker test. Icemaker not working as designed job completed.

"Cycled unit and found freezer door staying open. Made adjustments to bottom freezer door hinge retested door, not opening and closing as designed job completed."

"Installed new lightbulb, and re-tested unit now working as designed job completed"

"Found unit with defective dispenser, fixed dispenser, tested unit and is working properly, customer education on use and care."

"Tested unit and is working properly. Unit had sheet stuck in agitator, tested all ops are are working fine

"Replaced defective cap, tested unit and is working properly."

Found unit with electrical issue from home also found unit on blocks.informed client of block issue and anti tip bracket.

JB out 7/18/23. Installed replacement Machine Control Board WD21X31739 and Screw WD02X10220. Tested unit. Dishwasher now operates as designed. JOB COMPLETE

"JB out 7/18/23. Customer states that the washer Will intermittently shut off mid cycle and the only way to get it to operate again is to unplug it from the outlet and plug back in. Upon arrival found washer in wash mode with laundry as required. Observed washer fill to correct water level and wash properly. After 25 minutes, canceled wash cycle to test drain and spin functions. Tested drain and spin. Verified correct function. Ran diagnostics extract two stored error code. Both are F0E5 indicating Off Balance condition detected. Cleared stored error codes. Unable to very complaint or any mechanical defects today. Recommend customer to load clothes in loose heaps evenly around the outer part of the WASHPLATE as outlined in the supplied use and care guide. Tested in Rinse & Spin mode. Observed F7E8 error. Fold is displayed when the main control determines the motor temperature is too high.. inspected motor rotor fell covered in linden dust. Brush, clean cooled off motor and re-tested unit now operate properly. No parts used. No repair made.NOTE: suggest customer replace existing black rubber inlet fill hoses to prevents potential flood. These hoses should be replace every 4-5 years regularly.No charge to customer.JOB COMPLETE"

Found slider stripped replaced tested working properly ; used 1 W10734521 (SLIDER) from stock

Tested icemaker cycles half bucket of ice customer not happy with iceproduction called tech sr7736679473Per tech line unit is working as designed and no work is needed

Installed control board tested working properly

Found drian pump and cap bad replaced tested working properly

Found valves bad replaced tested working properly

"Unit door is broken off looks as if door is not able to put right back and will need the whole assembly to be fixed price quote was given to Cx . Cx will call wp see if they can do anything regarding issue, job completed.

"All 12 led module lights where replaced which turned back on all lights, now all lights working no further issues, job completed."

"Cx called about some black streaks coming out of little holes where soap detergent goes in through, when diagnosed unit did service test there was no error codes passed. Checked inside in bottom of detergent holes and found some mold and gunk Cx said was not staining clothes but did see the dark streaks, Cx will have to clean it in order for issue not to be happening anymore will buy brush to clean it no further issues, job completed."

"Unit was not draining, noticed both wires on bottom that go connected to drain pump where not making contact on wire ,once adjusted wires, tested now draining left washer with clean with affresh cycle since water was old and unit smelled, job completed."

"Both parts where replaced tested after repair and temp reached 350 right away explained to Cx about pre heating cycle as well, no further issues job completed."

Bellows moldy. Customer wanted to replace. Customer approves

Installed damper and thermostat. Tested unit. Unit is working properly. Customer approves. Will call if problems continue.

Found unit not properly spinnning tub. Found unit with stripped drive hub. Replaced with RKSTK and tested unit. Unit is working properly. Customer approves function at this time.

Found unit with an F8E1 long fill error code. Found unit with a faulted water valve. Replaced valve and tested. Unit is working properly. Customer approves function at this time.

Found unit not filling. Canceling cycle due to not spinning properly. Found slider worn causing gears not to properly engage. Replaced slider with TRKSTK and tested. Unit is working properly. ; used 1 W10734521 ( Slider) from stock

Unit not draining. I found that the dishwasher was draining normal. The air gap at the sink is clogged. Instruct customer on clogged air gap. All tests good.

Unit making noise during bake cycle. I found that the convection fan motor was making noise. Removed and replaced fan motor blade and tightened panel. All tests good.

Removed and replaced sensor harness and coils. All tests good.

Replaced the ice maker and installed the adapter kit tested ops ok now at this time

Replaced the middle mullion rail operations will be ok when turned on

"Replaced the dispenser soap pump and cold water valve , tested operations ok now at this time"

Old unit was in the garage. Installed new unit in the kitchen. New unit operating as designed. Evaporator and compressor.

Installed all new parts and was able to correct the issue. Unit now working as designed.

Installed all new parts. Re-tested unit. Unit is now operating as designed.

Installed new rails and verified drawers is opening and closing without issue.

F0E5 F7E5 Found debris stuck in slider which was causing poor shifting. Cleaned the area and retested. Unit is now shifting without issue.

Installed both parts. New diffuser is testing good.

"Found failed lock strike causing unit not to run, replaced strike all tested good"

Replaced vent and lock all tested good

Replaced evaporator fan motor all tested good

"Cabinet has dents 1 on each side towards the back bottom of the cabinet and 1 on the rear, per GE TECH 2 side dents are cosmetic and the rear dent cold be popped out file # 10596292Popped out rear dent to the best of my ability see pics"

"Found worn rollers and belt pulley, installed kit replacing all worn out parts all tested good"

"Found failed module in fresh food compartment, replaced module all tested good ; used 1 W11462342 (Module) from stock"

"F0e4, f1e2, f9e1, f8e1, f5e1.Removed pump and flushed out impeller. Reinstalled and unit now draining with no issues. Calibrated main control. All functions now working as designed."

Confirmed bad icemaker.Cx does not want to go through with repair.

Installed new parts. All ops now working as designed.

"Fixed- installed new parts (harness, pan) checked- cooling, temperature, lights, fans, gaskets, are all working as designed- cx ok repair"

Fixed- installed new part (cntrl elec) auto test pass- no leaks- no errors- heater is working- cx ok repair.

"Found unit making contact with gas line, re adjust lines and leveled unit. It is now working ok"

He led unit found unit would shut off when attempting to use. Found open ground on outlet also found loose incoming power connector. Re secured connection and tested ops unit worked ok. Also advised cx fixing outlet for proper function.

"Ran spin cycle, customer had concerns with the drain hose shaking during spin, advised customer that this is normal due to the force water in the hose and the spin. Tub is not shaking excessively, only normal wash movement and noises is present. Washer is functioning as designed."

"Found the RC defrost drain blocked, defrosted drain with my steamer, unclogged drain and verified water is flowing. Unit is functioning as designed"