Service History 100 - Appliance Repair Specialists

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHV01

Near Moorpark, CA 93021

Paul M

Job Details: 02/01/2025

"Unit was leaking from filter head, replaced filter head and added sealer gum to close air gap where water line is. Replaced bad led lights in the refrigerator section. Unit is now working properly. Job complete; used 1 212643 (Seal gum) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SNHM09

Near Riverside, CA 92503

Robert U.

Job Details: 02/01/2025

Found the unit making a rattling sound and I found two screws for the back panel loose so the panel was not guiding the air properly and making noise. So I adjusted the panel and tightened the loose screws. All functional issues were now addressed. As for the door. The door does have rust on it and is only covered for the first 30 days of ownership. I recommend the customer contact whirlpool to get a concession pl1. So we can get this resolved for the customer. All functions however are now working after repair. Job completed.

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Riverside, CA 92503

Robert U.

Job Details: 02/01/2025

Found the unit not draining and leaving water in the tub. I removed the water and found the black wire going to the drain pump broken. I replaced the entire lower wiring harness and all functions were restored and working. I ran a diagnostic cycle to check all other components and all functions restored and working as designed. Job completed.

We serviced a

WHIRLPOOL DRYER

Model WGD5050LW3

Near Victorville, CA 92392

Brian G

Job Details: 02/01/2025

Diagnosed open thermal fuse. Removed and replaced thermal. Advised customer that their vent is restricted and needs to be serviced. Unit Tested good

We serviced a

MAYTAG WASHER

Model MVWB855DC

Near Hanford, CA 93230

Enrique

Job Details: 02/01/2025

"Customer concerns: washer making loud noise during spin cycle. Faulty slider. Installed slider assembly, performed calibration. Washer operating as designed. No leaks.; used 1 W10734521 ( Slider) from stock"

We serviced a

WHIRLPOOL WASHER

Model WFW4720RW0

Near Riverside, CA 92509

Robert U.

Job Details: 02/01/2025

Found leak coming from the hose that goes from the tub to the pump. At the pump side. I reinstalled the clamp and made adjustments to the hose and the unit is no longer leaking. I ran a diagnostic cycle and recalibrated the unit. All functions tested ok and unit is no longer leaking. Job completed.

We serviced a

GENERAL ELECTRIC WASHER

Model GFW850SPNRS

Near Fresno, CA 93722

David C

Job Details: 02/01/2025

Found faulty control replaced control tested unit unit it unit working as designed

We serviced a

MAYTAG WASHER

Model MVW6500MBK

Near Salida, CA 95368

Andrew H

Job Details: 02/01/2025

Cx complaint. making grinding noise. AGITATOR AND DRUM ARE SPINNING OPOSITE DIRECTIONS - MNIMAL WATER LEVEL. Upon arrival. Ran diagnostics. Found drive pulley fault. Actuator failed. Installed actuator. Installed driver pulleys. Tested components out okay okay. Operation as according to protocol designed.

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Modesto, CA 95351

Timothy G

Job Details: 02/01/2025

Testing reviled a failed capacitor. Had one in truck replaced and unit passed all tests. Job complete ; used 1 W11428524 (Capacitor) from stock

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS3

Near Thousand Oaks, CA 91360

Richard R

Job Details: 02/01/2025

"Upon arrival, removed faulty wash motor assembly. Replaced it with new one tested unit. Unit is now working as intended job complete cleared all error codes in diagnostics."

We serviced a

GENERAL ELECTRIC WASHER

Model PFW870SPV0RS

Near Santa Maria, CA 93454

George

Job Details: 02/01/2025

Found washer testing out ok customer concern exexively shaking put smart h q out of balance loads removed item reposition tested thrue a full quick wash completed ok complete.

We serviced a

WHIRLPOOL DRYER

Model LGB6300PW0

Near Riverside, CA 92503

Robert U.

Job Details: 02/01/2025

Found the thermal fuse open and reason for heating failure. I replaced the thermal and verified operation of the valve and the valve is now working properly. All functions restored and heating. Job completed.

We serviced a

WHIRLPOOL DRYER

Model WGD8127LW1

Near Bakersfield, CA 93306

James

Job Details: 02/01/2025

Was able to remove blower wheel without removing motor. Replaced blower wheel and installed repair kit. Tested unit. Unit now working as intended.

We serviced a

ZLINE WALL OVEN

Model AWS-30

Near Paso Robles, CA 93446

Jack

Job Details: 02/01/2025

Found original cooling fan is bad. Took apart and tested. The fan is not aligned properly. Checked out and now the new fan is working as designed. Job completed. Tested while a part and tested while in wall. All checked out. Zline sent customer the cooling fan.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FPS06

Near Calabasas, CA 91302

Richard R

Job Details: 02/01/2025

Upon arrival inspected unit customer stated that unit was not shutting correct inspection I found that fresh fruit door gasket was not seated correctly was able the gasket and adjust the door up and down with the leveling screw that it has on the right hand door tested unit. Unit is now ceiling and working as intended. are normal job complete

We serviced a

MAYTAG DRYER

Model MGD7230HW3

Near Bakersfield, CA 93304

James

Job Details: 02/01/2025

Panel buttons not responding to touch replaced ui panel and unit now working as intended.

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Bakersfield, CA 93312

Chase

Job Details: 02/01/2025

Customer is concerned about sound of the shifter between agitation and spin cycles. This is a normal operating sound. Removed and reinstalled shifter. Explained operation to cx. Unit is working as designed.

We serviced a

WHIRLPOOL DRYER

Model WGD6120HW3

Near Hesperia, CA 92344

Brian G

Job Details: 02/01/2025

Inspected unit as necessary. Diagnosed control board dropping out causing unit not to run intermittently. Removed and replaced control board. Tested operation. All OK. If problem persists customer will need dryer motor and blower wheel.

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Keyes, CA 95328

Timothy G

Job Details: 02/01/2025

Replaced damaged harness and unit wire is good. Found pump shorted and humming after repair of harness. Replaced pump and unit is now draining per design. Job completed.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ1

Near Merced, CA 95348

Cruz

Job Details: 02/01/2025

Complete- power cord is not covered under warranty- found power cord and receptacle to be burned- look at pictures- cx will need to replace power cord first- then give as us a call for diagnostic testing-

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Riverside, CA 92503

Robert U.

Job Details: 02/01/2025

Found the door latch defective and not allowing the unit to start a cycle. There is only one error code stored and that is a f5 code for a bad door latch. After replacing the latch assembly the door is now able to be locked and continue with the cycle. All functions restored and working. Job completed.

We serviced a

MAYTAG WASHER

Model MVW7230HW1

Near Ceres, CA 95307

Timothy G

Job Details: 02/01/2025

"Inspected unit and found clicking noises in agitator. Removed and found plastic piece from agitator. Replaced and reassembled, unit is now working per design"

We serviced a

WHIRLPOOL OVEN

Model WOS51EC0HS20

Near Madera, CA 93636

David C

Job Details: 02/01/2025

Replaced ui tested y it unit working as designed

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Highland, CA 92346

Robert U.

Job Details: 02/01/2025

After replacing both main control and pump and motor assembly the wash motor is now operating. I verified the operation of all other components and all components are functioning properly. After diagnostic no error codes were stored and the heater is operating. I verified no leaks during operation. All functions are now working. Job completed.

We serviced a

MAYTAG WASHER

Model MVW6200KW2

Near Bakersfield, CA 93311

Chase

Job Details: 02/01/2025

Installed new control and harness. All functions now working as designed.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN3WW

Near Baywood-Los Osos, CA 93402

Jack

Job Details: 02/01/2025

"Checking out unit. Running smart hq first. 5 codes. F9 f1 f32 which is active. F31 out of balance and f23. Unit also had over loading, replaced lock mechanism assembly. WH08X37938 came with everything that was needed for repair. Ran diagnostics test and everything thing is working as designed now. Job completed"

We serviced a

MAYTAG WASHER

Model MVWC565FW3

Near Manteca, CA 95337

William

Job Details: 02/01/2025

"F7E6, F7E7, checked splutch functions, replaced lower wire harness, ran self diagnostic cycle, ran test agitate & spin cycle several times, tested ok, unit operating as designed."

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN9WW

Near Grover Beach, CA 93433

George

Job Details: 02/01/2025

Installed parts tested check out ok complete.

We serviced a

JENN-AIR COOKTOP

Model JED3430GB01

Near Manteca, CA 95336

William

Job Details: 02/01/2025

"Replaced glass cooktop & gromets, checked all cooktop functions, unit operating as designed"

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near San Fernando, CA 91340

ERICK H

Job Details: 02/01/2025

Inspected hinges. No damage to hinges. Replaced lid and bezel. Unit operating as designed. Job complete.

We serviced a

GENERAL ELECTRIC DGOS

Model GFW550SSN2WW

Near Planada, CA 95365

Cruz

Job Details: 02/01/2025

"Fixed- installed new parts (inverter, main cntrl) reprogram unit, all trst pass- no leaks- no errors- cx ok repair"

We serviced a

GENERAL ELECTRIC DRYER - ELECTRIC

Model GTD48GASW0WB

Near Madera, CA 93637

David C

Job Details: 02/01/2025

Replaced idler arm tested u it unit working as designed

We serviced a

GENERAL ELECTRIC DRYER - GAS

Model GTX33GASK1WW

Near Monrovia, CA 91016

Stephen

Job Details: 02/01/2025

Found front bearing slide popped out of bearing housing. Reinstalled slide. Tumbling and heating properly at this time. Advised customer foil duct is fire hazard. Advised customer to have semi flexible aluminum ( not foil ) duct with 2 90 degree elbows installed by appliance installer or duct cleaning service. Complete.

We serviced a

MAYTAG WASHER

Model MVWP575GW0

Near La Puente, CA 91744

Stephen

Job Details: 02/01/2025

"3 count job. Allow 2 1/2 hours. Replaced gear case, splutch, belt, shifter, and hub. Fills, agitates, drains, rinses, locks/ unlocks, and spins properly at this time. Complete."

We serviced a

WHIRLPOOL RANGE

Model WFES3530RS0

Near Manteca, CA 95337

William

Job Details: 02/01/2025

"Checked voltage to unit, Ran bake cycle, checked current draw, unit draws 14 amps max in bake cycle, bake element resistance at 23.6 ohms , after 2 breaker resets able to get unit to preheat to 350 degrees, unit operating as designed. Service pointer # W11525530, no tech line available."

We serviced a

WHIRLPOOL OVEN

Model WOS51EC0HS20

Near Riverside, CA 92507

Robert U.

Job Details: 02/01/2025

After replacing both the panel and main control the panel is now responding to touch properly and is also heater properly. There are no error codes stored at this time. All functions restored and operating after repair. Job completed.

We serviced a

GE DRYER

Model GFD65GSSN0WW

Near Paso Robles, CA 93446

Jack

Job Details: 02/01/2025

Replacing main board. Programming new board into system. Tested and working. Unit is not showing anymore codes. Tested again and worki. Job completed

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model GNE27JYMWFFS

Near Planada, CA 95365

Cruz

Job Details: 02/01/2025

"Fixed- installed all new parts (door ss, mullion, 3 gaskets, 2 sliders) freezer door is now sealing to cabinet- gaskets, fans, are now working- cx ok repair"

We serviced a

ELECTROLUX WASHER

Model ELFW7637AT0

Near Modesto, CA 95356

Timothy G

Job Details: 02/01/2025

Tech damaged dispenser tray handle. This should not be billed. I was unable to call and see what exactly to do. Follow up scheduled for ; ordrng 1 5304515293 (Dispenser handle)

We serviced a

MAYTAG REFRIGERATOR

Model MSS25C4MGZ08

Near Modesto, CA 95350

Timothy G

Job Details: 02/01/2025

Unit has a bad plug for evaporator heater. Need to follow up with new heater with harnesses Follow up scheduled for Thursday ; ordrng 1 W11650661 (Heater with harness)

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Keyes, CA 95328

Timothy G

Job Details: 02/01/2025

"Inspected unit and found errors for motor voltage and also communication error, need to follow up to repair. Tuesday pm call preferred ; ordrng 1 W11513246 (Control) and 1 W11026785 (Motor)"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FRSS2623ASA

Near Armona, CA 93202

Enrique

Job Details: 02/01/2025

Customer concerns: both compartments not cooling correctly. Evaporator frosting up. Defrost system issue. CUSTOMER WILL SHUT REFRIGERATOR OFF 2 DAYS PRIOR TO SERVICE. ; ordrng 1 5304526032 (Heater) and 1 5304532557 (Motor) and 1 5304525990 (HARNESS ASSEMBLY)

We serviced a

GE DRYER - GAS

Model GFB55GSSN3WW

Near Hanford, CA 93230

Enrique

Job Details: 02/01/2025

Dryer is making loud rattling noise. ; ordrng 1 WE16X33977 (BLOWER WHEEL) and 2 WE03X10016 (ROLLER ASM WHEEL)s and 1 WE03X30657 (IDLER ARM)

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Oakdale, CA 95361

Andrew H

Job Details: 02/01/2025

Cx complaint. Not heating. Ordered W10900067 cut off. Open sensor. Upon arrival. Ran diagnostics. Found open sensor. Re route for parts. Error code 2*1. 240 volt to unit.; ordrng 1 W10900067 (Cut off)

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW4

Near Simi Valley, CA 93063

Paul M

Job Details: 02/01/2025

"Unit was not heating properly, when unit goes from low to high unit will not heat. Will need to replace temperature switch and timer. Order sensors incase I still need them. ; ordrng 1 W11050715 (Temperature switch) and 1 WPW10185981 (Timer) and 1 WPW10117655 (Push start)"

We serviced a

WHIRLPOOL DRYER

Model WGD5050LW3

Near Simi Valley, CA 93063

Paul M

Job Details: 02/01/2025

"Gas valve, unit has a small leak. Can smell it at very low but was hard to detect. ; ordrng 1 W11652257 (Gas assembly)"

We serviced a

MAYTAG WASHER

Model LA610

Near Riverside, CA 92506

Robert U.

Job Details: 02/01/2025

Found several issues with the washer. As for shaking it is caused by a few thing. First the damper pads are all gone. Also the front panel is missing the screw for the front left so the machine itself is not sturdy as a result when operating. Also the motor shield is missing and water is getting on the wires connecting to the motor. The brake is squealing and moving machine when unit stops during spin. Ordering all parts needed several parts are nla. ; ordrng 1 203956 (Damper pads) and 1 215098 (Motor shield) and 1 WPW10346892 (Screw motor mount) and 1 204439 (Screw and fastener) and 1 12112425 (Belt) and 1 201190 (Brake assembly) and 1 Maytagbreaktool (Maytag break tool)

We serviced a

WHIRLPOOL DRYER

Model WED7120HW1

Near Modesto, CA 95355

Andrew H

Job Details: 02/01/2025

2*1 cx complaint. Not heating. Upon arrival. Ran diagnostics. Found 2*1. Open heating element ; ordrng 1 WP3387747 (Heating element) and 1 280148 (Cut off)

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near San Luis Obispo, CA 93401

Jack

Job Details: 02/01/2025

Sensing spin done/ done. Sensing/rinse done. F3e1 pressure sensor. W11603810 main board with pressure sensor. ; ordrng 1 W11603810 (Main board)

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ1

Near Burbank, CA 91506

Tim B

Job Details: 02/01/2025

Found console adhesive peeling from plastic causing buttons on ui to fail. Will need to replace both ui and console together.; ordrng 1 W11460908 (Console)

We serviced a

KITCHENAID REFRIGERATOR

Model KRSF705HPS05

Near Madera, CA 93636

David C

Job Details: 02/01/2025

Repair was unable to fix unit will have to Texh Monday; schdld next appmnt for 2/3 MON !

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Merced, CA 95348

Cruz

Job Details: 02/01/2025

Need work- found pump to be running continuously- causing unit not to start- lights on panel flashing- will need to order part - ; ordrng 1 W11603810 (Cntrl elec)

We serviced a

KITCHENAID DISHWASHER

Model KUDS01FLSS6

Near Simi Valley, CA 93065

Paul M

Job Details: 02/01/2025

"Unit is leaking from striker and door latch. Aligned unit properly and did not have any complications closing door. After repair unit still leaked from door late he, door looks bent in on the top which is where it seems to be coming from. Will need to replace door but door is unavailable. ; ordrng 1 8530900 (Inner door) and 1 8530900 (Tub) and 1 W10864081 (Seal)"

We serviced a

GENERAL ELECTRIC DISHWASHER - BUI

Model GDF510PSR6SS

Near Santa Maria, CA 93454

George

Job Details: 02/01/2025

Found dishwasher door not closing broken latch.need this part to complete service.unit 205; ordrng 1 WD01X29878 (Doorlatch)

We serviced a

WHIRLPOOL DRYER

Model WGD5605MW1

Near Santa Maria, CA 93455

George

Job Details: 02/01/2025

Found dryer screaching wen in used need this parts to complete service.; ordrng 1 W11364931 (Motor) and 1 WP697772 (Blower)

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS01

Near Santa Maria, CA 93455

George

Job Details: 02/01/2025

Found refrigerator with no errors not filling need this parts to complete service.; ordrng 1 WPW10341329 (Valve) and 1 W11658802 (Ice maker)

We serviced a

GENERAL ELECTRIC DRYER - ELECTRIC

Model DSKS333ECWW

Near Los Alamos, CA 93440

George

Job Details: 02/01/2025

Installed cover need knob for timer assistance to order correct knob; saved tckt

We serviced a

WHIRLPOOL DRYER

Model WGD5620HW

Near Arroyo Grande, CA 93420

George

Job Details: 02/01/2025

Found drum warp need this part to complete service.; ordrng 1 W10508188 (Tub)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ13

Near Los Angeles, CA 91367

Richard R

Job Details: 02/01/2025

"On arrival inspected unit found unit dispensing ice and the icemaker mold but not dispensing water when asked for inspected valve found water dispense valve not opening bad solenoid, ordering a water valve assembly; ordrng 1 W11645245 (Water valve assembly)"

We serviced a

GENERAL ELECTRIC WASHER

Model GFW850SPN5RS

Near Santa Paula, CA 93060

Isidro

Job Details: 02/01/2025

"I found a broken dispenser on arrival, reordering part ; ordrng 1 WH42X29542 (Dispenser kit)"

We serviced a

KITCHENAID REFRIGERATOR

Model KBSD606ESS00

Near Riverside, CA 92506

Robert U.

Job Details: 02/01/2025

Found the shaft for the ice dispenser feel out of position again. Will need to replace the shaft. Ordering part needed. ; ordrng 1 WP2318082 (Shaft)

We serviced a

KITCHENAID REFRIDGERATOR

Model KRMF706ESS01

Near Riverside, CA 92503

Robert U.

Job Details: 02/01/2025

Found the unit has a few issues going on first the unifies not cooling. I found two broken wires going to the left pantry. Also the top refrigerator leds are flickering and not staying on properly. There is also an issue with the front control panel not excepting commands. Will need to replace that as well. Because of the cooling issues there was water in the pantry user interface so the seal on the door is bad and needs to be replaced. Will order all parts needed to resolve issues. Pantry door is on back order so the office will be reaching out to reschedule. ; ordrng 1 W11170612 (Harness wire) and 1 W10815668 (Door pantry) and 1 W11683244 (Led modules) and 1 W11330971 (Control electric) and 1 W11026418 (Trivet)

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Bakersfield, CA 93306

James

Job Details: 02/01/2025

"Unit has pressure system error and long drain error. Ordering new drain, harness and control. ; ordrng 1 W11399437 (Drain pump) and 1 W11513246 (Control) and 1 W11643701 (Wire harness) and 1 W11755726 (Clip)"

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Santa Clarita, CA 91354

ERICK H

Job Details: 02/01/2025

Lid was locked due to washer not draining. Unit isnt draining due to damaged lower harness. I was able to wiggle lower harness and get washer to drain water. Lower harness will need to be replaced. Will bring control back with me just in case unit is permanently stuck in emergency drain mode. ; ordrng 1 W11643701 (Lower harness)

We serviced a

WHIRLPOOL RANGE

Model KGRS505XSS01

Near Los Angeles, CA 91344

ERICK H

Job Details: 02/01/2025

Cx states gas smell when bake cycle in upper oven is in use. Confirmed issue. Only right side of burner is igniting. Issue only occurs with bake baffle and shield installed. Burner has full ignition when baffle and shield are uninstalled. Will call tradecare team Monday to report findings. ; schdld next appmnt for 2/3 MON !

We serviced a

WHIRLPOOL REFRIGERATOR

Model MRT711SMFZ00

Near Los Angeles, CA 91342

ERICK H

Job Details: 02/01/2025

Cx states frost in freezer and water in rc. Fc door gasket is damaged and falling off. There is also damage to the liner at the bottom of the rc. Pics provided. Liner is a non-serviceable part. Will have to pseudo call for Monday to document with WPL. ; schdld next appmnt for 2/3 MON !

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ18

Near Morro Bay, CA 93442

Jack

Job Details: 02/01/2025

Picking up data loggers for info of fridge temp issues. ; snapped 1 QuickPics

We serviced a

BOSCH REFRIGERATOR

Model B36CT80SNS/08

Near Nipomo, CA 93444

Jack

Job Details: 02/01/2025

Round unit not working were fan is dead. Ice buildup on back wall. Calling tech line to document issue. Freezer door is also not shutting properly. Took out ice buildup and helped a little on door closing. But still an issue. ; schdld next appmnt for 2/3 MON !

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ2

Near Bakersfield, CA 93311

Chase

Job Details: 02/01/2025

Cannot test unit due to a glitched out ui. Will need to replace ui and console. Will have parts needed incase there is a leaking issue. ; ordrng 1 W11460908 (Console) and 1 W11632709 (Ui)

We serviced a

GENERAL ELECTRIC DRYER - ELECTRIC

Model HTX26GASW0WW

Near Bakersfield, CA 93313

Chase

Job Details: 02/01/2025

Diagnosed dryer not heating. Found open safety thermostat now allowing cycle of heat to come through. Ordering safety and hi limit thermostats. ; ordrng 1 WE04X26138 (Hi limit) and 1 WE04X25199 (Safety thermostat) and 1 WE04X25201 (Inlet thermostat)

We serviced a

GENERAL ELECTRIC DRYER - ELECTRIC

Model GTD48GASWWB

Near Hesperia, CA 92345

Brian G

Job Details: 02/01/2025

"Inspected unit as necessary. Diagnosed flame sensor failure. Ordering flame sensor, gas valve and igniter. Parts ordered.; ordrng 1 WE4X448 (Flame Sensor) and 1 WE11X35317 (Valve Assembly) and 1 WE4M449 (Igniter)"

We serviced a

WHIRLPOOL DRYER

Model LG7001XMN2

Near Clovis, CA 93619

David C

Job Details: 02/01/2025

Will need help locating parts; schdld next appmnt for 2/3 MON !

We serviced a

MAYTAG WASHER

Model MVWC465HW2

Near Bakersfield, CA 93301

James

Job Details: 02/01/2025

"No error codes, ran diagnostic cycle. Unit not shifting out of agitation causing drag on belt. Belt sliding. Needs cam, belt and actuator Cam w10721967 $53.27Belt w11239857 $70.96Actuator w10913953 $83.58Parts: $207.81Service Charge: $145.00FRL: L14 - $187.92 Additional Labor: $0.00Other: $0.00Subtotal: $540.73Tax: $15.59Job Rate: $556.32Customer denied repair and will look into a new unit. Collected service 145.00 via cc$145.00 CC Auth# ML3XPR"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ07

Near Bakersfield, CA 93305

James

Job Details: 02/01/2025

Unt has torn right and left door gaskets. Also has large led light in FF dim and flickering. Replaced gaskets with pre Id parts and used heat to form seal. Ordering large led module. ; ordrng 1 W11527432 (Large led)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WSR57R18DM02

Near Los Angeles, CA 91316

Tim B

Job Details: 02/01/2025

Wrong service ordered for unit. Will need correct service kit to complete repair.; ordrng 1 W10812028 (Service kit)

We serviced a

WHIRLPOOL WASHER

Model MVW7230HW1

Near Hanford, CA 93230

Enrique

Job Details: 02/01/2025

"Power button was not working. Installed new UI, programmed control. Washer operating as designed. No leaks."

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW3

Near Simi Valley, CA 93063

Paul M

Job Details: 02/01/2025

"F7E1 basket speed faultUnit was not going into spin or agitate, checked capacitor and found it was not working properly. Replaced with new capacitor unit is now working properly.; used 1 W11395618 (Capacitor) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT518SZFW04

Near Oakdale, CA 95361

Andrew H

Job Details: 02/01/2025

"Freezer door POPS OPEN WHEN FRDIGE DOOR CLOSED, RUBS AS ITS CLOSING. LOOSE GASKET. Upon arrival. Ran diagnostics. Found door hinges loose faulty. Attached door hinges tightened. Tested Clarence out okay okay. Operation as according to protocol designed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ08

Near Modesto, CA 95351

Timothy G

Job Details: 02/01/2025

"Was able to get proof of purchase see photo. Inspected unit and found unit clogged with ice. Removed panel and was unable to access components, Advised Cx to defrost and get unit cooling again. Cx approved and will defrost unit for 24 hrs and then plugg in and wait 24 more hrs for unit to get to temps. Advised Cx to reset ice maker. Cx will call back if unit has any issues after complete defrost"

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Riverbank, CA 95367

Andrew H

Job Details: 02/01/2025

"AIG Washer making loud metal grinding metal sound, still present. Cx complaint. Upon arrival. Ran diagnostics. Found loose motor connections.attached motor bolt to unit."

We serviced a

JENN-AIR REFRIGERATOR

Model JFX2897DRM02

Near Thousand Oaks, CA 91362

Richard R

Job Details: 02/01/2025

"Upon arrival inspected unit customer stated that unit intermittently would lose power and stop cooling upon my arrival. Inspected the unit. Customer stated the unit has been working for the past couple days correctly checked for frost buildup on evaporators could not see anything. Compressor and condenser fan are running correctly possible short inevaporator fans gave customer quote for both fresh food and freezer evaporator fan motors with harnesses. at this moment, she is going to think on repairing it advise her."

We serviced a

FRIGIDAIRE WASHER

Model ELFW7637AT1

Near Bakersfield, CA 93313

Chase

Job Details: 02/01/2025

Ran through a test cycle and confirmed there is a major buildup of sides. Customer using too much detergent. Flushed sides out from basket. Ran through rapid cycle. All functions now working as designed with no leaks.

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW1

Near Modesto, CA 95356

Andrew H

Job Details: 02/01/2025

"will not start, HAS POWER LIGHTS UP, ERROR CODE F7 E1, UNIT. F9*1. Cx complaint. Not draining. Upon arrival. Ran diagnostics. Found error code. Drain pump faulty. Installed drain pump. Tested components out okay. Operation as according to protocol designed ; used 1 W11578225 (Drain pump) from stock"

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Thousand Oaks, CA 91360

Richard R

Job Details: 02/01/2025

Upon arrival found broken lid lock replaced lid lock tested unit unit is now locking and working as intended. All operations are normal job complete also ran a factory calibration on the unit and reprogrammed central control board.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS3

Near Bakersfield, CA 93312

Chase

Job Details: 02/01/2025

"Open float switch, installed new float switch. Programmed and tested, all functions now working as designed."

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Hanford, CA 93230

Enrique

Job Details: 02/01/2025

"Broken pump harness. Installed new harness, performed calibration. Washer operating as designed. No leaks.; used 1 W11643701 ( Harness) from stock"

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near Santa Paula, CA 93060

Isidro

Job Details: 02/01/2025

"Unit going straight to done when starting cycle, I installed new capacitor and actuator then calibrated unit. Tested and its now washing and operating as designed at this time of service, cx approved repair"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDHV08

Near Los Angeles, CA 91335

Tim B

Job Details: 02/01/2025

Replace door gasket and unit functions as normal

We serviced a

WHIRLPOOL WASHER

Model MVW6500MBK

Near Bakersfield, CA 93309

Chase

Job Details: 02/01/2025

Broken strike. Installed new strike. All ops now working as designed. ; used 1 W11457841 (Strike) from stock

We serviced a

WHIRLPOOL RANGE

Model KSGG700ESS3

Near Apple Valley, CA 92307

Brian G

Job Details: 02/01/2025

Inspected unit as necessary. Diagnosed obstruction in front right burner orifice causing burner not to light. Technician removed burner orifice and removed obstruction. Reassembled unit and tested operation. All OK

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Manteca, CA 95337

Andrew H

Job Details: 02/01/2025

OUR WASHING MACHINE IS NOT WORKING PROPERLY. IT DOESN'T FINISH THE CYCLE - NEEDS DRAIN PUMP. Cx complaint. Ill plan on arrival. Ran diagnostics. Found error code. Long drain. Found error code suds. Bubbles in pump assembly. Installed new drain pump. Checked out components OKAY . operation as according to protocol designed.

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Santa Clarita, CA 91350

ERICK H

Job Details: 02/01/2025

Replaced control. Performed diagnostic cycle. Unit completed cycle with no functional failures. Unit operating as designed. Job complete.

We serviced a

JENN-AIR REFRIGERATOR

Model JS48PPDBDA

Near Los Angeles, CA 91403

Tim B

Job Details: 02/01/2025

Units evaporator fan motor making loud grinding noise until door is opened. As well as icemaker not producing ice no parts available for this unit. Customer will proceed accordingly.

We serviced a

GE WASHER

Model GTW330ASK0WW

Near Bakersfield, CA 93305

Brandon

Job Details: 01/31/2025

Agitator is broken at the base and wont spin wont the transmission. Quoted Cx on agitator replacement. She said they probably wont repair it. Collected service fee.; ordrng 1 WH43X30957 (Agitator)

We serviced a

MAYTAG WASHER

Model MVW5035MW2

Near Simi Valley, CA 93065

Paul M

Job Details: 01/31/2025

"F8E1 long fillUnit was shaking when bulky items are used, replaced belt on unit and calibrated. Unit is now working properly. ; used 1 W11239857 (BELT) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT138FFDW01

Near Livingston, CA 95334

Cruz

Job Details: 01/31/2025

"File # 7740859799 from WP tech- support- need to replace compressor, evaporator, possibility of a leak- no frost pattern- look at pictures- ordering parts for unit. ; ordrng 1 W11578004 (Evaporator) and 1 W11635510 (Compressor)"

We serviced a

KITCHEN AID DISHWASHER

Model MODEL

Near Bakersfield, CA 93311

Randy

Job Details: 01/31/2025

Unit is not filling. Found unit had some item stuck under the float switch. Tested unit now fills and drains. Tested and now working as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WUI75X15HZ01

Near Turlock, CA 95380

Cruz

Job Details: 01/31/2025

"SR # 7740858643 from WP tech line- unit is making ice, but over flows with ice will not stop, tech- support said to replace bin thermistor- ordering part for unit. Q; ordrng 1 WPW10511923 (Bin thermistor)"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAKZ3

Near Lompoc, CA 93436

Kash S

Job Details: 01/31/2025

"Found unit leaning forward causing the drawers to push the door open during operation and stop cycle, tech leaned unit back, verified unit is starting cycles, cx has no further questions/concerns, unit is fully operational at this time"

We serviced a

GENERAL ELECTRIC WASHER-DRYER COM

Model GUD24ESSM1WW

Near Reedley, CA 93654

Joe P

Job Details: 01/31/2025

"Heating element came in contact with drum, damaged drum and heating element, ordering drum and heating element. ; ordrng 1 WE21X28956 (Drum) and 1 WE11M61 (Heating element)"