"Fixed- found refrigerator to be sagging causing gasket not to seal to cabinet. I then removed refrigerator door and adjusted lower hinge- reassembled refrigerator door, gasket is now sealing to cabinet, door is not sagging. Cx ok repair"

"Fixed- installed new parts (ice maker, valve) ice maker harvest and water filled mold- cooling and temperature are working fine as well- cx ok repair"

Fixed- error code f2e1 stuck key- cleared code- ran diagnostic test it pass- key test pass as well- all keys are now working as designed- cx ok repair

"Fixed- installed new parts (basket, 6 screws, slider, rotor, stator, clutch, gear case) calibration test pass, auto test pass- no leaks- no errors - unit working per design- cx ok repair"

"Fixed- installed new part (cap) cap is now secured, customer OK to repair"

Fixed- installed new part (bulb) freezer light in now working per design- cx ok repair

"Removed and replaced parts listed, left unit unplugged. Cx will report any issues after fully defrosting unit"

"Found a hose to the water inlet channel was not fully inserted, fully inserted the hose and clamp. Ran a normal cycle and Verified no leak is present anymore. Unit is functioning as designed."

Removed all led modules and installed the upgraded modules. Verified that they all function. Unit is functioning as designed

"Found an F2E1 code present, cleared code, disconnected power to the oven, removed old ui panel, all connections are intact, removed old and installed the new ui panel. Reconnected power and Verified the oven is functioning and the code is no longer present."

Ran the dryer for over 30 minutes while I was inspecting the washer and I was not able to duplicate any noise with the dryer. Unit is functioning as designed

"I found the ventilation with90% obstruction making unit take long dry times, removed large obstruction, I also adjusted the door, unit is now sealing properly as designed at this time of service, customer approved repairs"

Cycled unit and found Door not fully closing. Inspected unit and found customers floor is unlevel causing issue. Adjusted leveling feet as best as I could. Unit is working as designed. Job completed.

Installed new water tube retested unit now working as designed job completed

Installed new parts and re-tested unit now working as designed job completed

"Installed new evaporator and new compressor recharge system with 64 g of r600. It tested units and checked for leaks, all tests good. Unit now cooling working as designed to job completed"

"JB out 7/29/23. Customer states dishwasher is inoperative. It does not power up. Upon arrival found dishwasher recently installed without using under counter. Mounting brackets and junction. Box cover is not installed leaving in unsafe situation. Test the dishwasher found no power further inspection. found power cord installed correctly, plugged in the outlet under the kitchen sink, but out with under kitchen sink is governed by the wall-mounted switch for the garbage disposer cutting off the power to the dishwasher outlet as well as the garbage disposal. installer needs to be contacted to return to properly level the dishwasher and install the junction box cover, and the tow panel cover an electrician will need to come out and properly wire The Outlet saw that one plug is controlled by the wall switch. this will be for the garbage disposer and the other outlet is hot. 24 hours so that the dishwasher has constant power supply to it. Test the dishwasher verified fill, wash and drain functions. Also found left-hand side upper rack dish rack stop is missing. Advise customer manufactures warranty does not cover missing parts. In this part needs to be installed to prevent upper rack from sliding out completely when use this is a safety issue and must be taken care of. Advise customer of one time courtesy no charge on a no defect. Found service call visit. No charge to customer. Job complete."

JB out 7/29/23. Customer states newly installed double wall oven displays F3E0 when upper oven is used. Verified code. Removed oven from wall installation. Installed replacement Oven Sensor W11598120. Reassembled unit and reinstalled into wall cavity.Tested both upper and lower ovens set to Bake 350f.No charge to customer. JOB COMPLETE

"JB out 7/29/23. Install replacement lid, Assembly. Tested Lid dissembly in unit locks and unlocks as designed. found garments stuck under agitator. Removed stuck agitator remove garment. Reinstall agitator. Tested in normal wash cycle. No charge the customer. Job complete."

Installed compressor and recharged system with 5.75OZ of R134A refrigerant and tested unit. Unit is working properly. Customer approves function at this time.

Found unit making noise during agitation. Sounds like a dolphin. Found cam pulley nut backed out causing the pulley to drop and gears to rub. Removed the nut and applied loctite adhesive and reinstalled. Tested unit. Unit is working properly. Customer approves function at this time.

Valve stuck open. Causismg tub to fill with water. Replaced valve and tested unit. Unit is working properly.

Installed gasket and inner door. Tested. Unit is working properly. Customer approves function at this function

Installed drawer. Tested unit. Unit is working properly

Found buzzing noise coming from condenser rattling on the ground. Adjusted condenser and put unit on its feet just a hair to give condenser a little more clearance from ground. Unit is working properly. Customer approves. Will call back if problem continues.

Unit making noise during cycle and not cleaning clothes properly. I found that the noise was coming from the slider. Removed and replaced slider. Tested unit and gave tips for better performance. All tests good.; used 1 W10734521 (SLIDER) from stock

Removed and replaced main control and fill valve. Tested unit. All tests good.

"Customer is concerned with temps in RC, temp of water from dispenser and ice production being too slow. I took temps in both compartments. FC was at 4 degrees and RC was at 42. The ambient temp in kitchen was 95+ and a large family. I cycled ice maker, ice maker cycled normal. All tests good. Gave customer tips on not opening the door as much when kitchen is hot and gave customer expected ice production numbers. All tests normal."

Unit not draining and giving f9e1 error code. I verified voltage to drain pump but pump not responding. Failed drain pump. Removed and replaced drain pump. Tested unit. All tests good.

Customer unable to remove water filter from filter head. I found that the water pressure is too high to remove easy. I instructed customer on how to turn off water and release the pressure before replacing filter. All tests good with refrigerator.

Removed and replaced ignitor. Tested unit. All tests good.

Removed and replaced drain pump. Tested unit. All tests good.

Replaced all selected parts Unit working properly as required

Lid is broken Replaced lid door Unit working properly as required

Replaced evap fan motor fan is now turning on. Job complete

This unit was recently installed and install areas did not install any of the handles or set the temperatures .I having saw all three handles and set up the freezer and fresh food section temperatures to normal operation

"Visual and physical inspection was performed and also went underneath and inspected all the water related components to no avail, no water leaks were spotted."

"Because of a normal wear out physical damage, a new right side FF Section door sea has been replaced."

Ice maker was running as operated but water was not filling up the tray. Causing small cubes to get stuck and stop the ice maker. Cleared out ice and replace internal water valve to get proper water flow to the ice maker. Water flow to the unit is working as operated. ; used 1 W11043013 (Valve) from stock

Replace main pcb as it had error code. Unplugged and put new board. Everything is working as designed.

"Loud noise coming from pulley. Did not having barring to spin. Replaced with part #4392067. No noise, working as designed.; used 1 4392067 (Repair dry) from stock"

"Replaced manifold, burners had stripped nuts. Completed job, everything is working as designed."

Optical sensor change out. Removed existing optical sensor. Installed new optical sensor. Unit operating as designed

Control board change out. Removed existing control board. Installed new control board. Unit operating as designed.

Diagnostic check. Visual inspection. Unit had water coming out from underneath unit. Set down floor protector/pulled unit from wall. Waterline is made out of vinyl tubing connected to a for 34 miles 15 foot lane located in garage. Connected to filter and shut off valve. Unit leaking from supply hose connection at brass fittings. Shut valve off. instructed customer to make repairs to water supply line

Removed and replaced compressor drier precooler tubing and service stub. Installed and charged w. Nitrogen at 140 psi. Wont hold. Sprayed all joints down with micro leak detector. No visible leaks at joints. Called techline. Spoke w garret at techline. File number #7736971520 Informed of issue. Documented and forwarded me to master tech Master tech informed me they going to send in for review

Removed and replaced ui. Tested now working as designed. Job complete Collected balance

"Removed and replaced control ui, door ice, and diffuser. Now working as designed. Cx instruct on proper airflow. Job complete"

Ice cubes are small. Found unit wont dispense water w enough pressure. Cx bought unit in December. Never changed filter. Removed filter now water pressure returned to normal but cx needs new filter. Unit is working as designed. Job complete

"On arrival, customer states no ice production or low ice production tested and found clogged filter filter is defective. Customer had new filter, replaced and tested unit now has the proper dispensing volume. Unit functions as design."

"On arrival unit located outside installed user interface fan, scroll and Thermist or kit tested unit function does designed needs to regulate to temperatures"

"Installed valve and tested, unit functions as designed."

"On arrival unit unplugged. Cx states PO shown when unit goes into defrost. Ran loads could not duplicate, possible defrost or control issue. Display on UI has weird outline on background possible dc short. Quoted for HV and LV board but advised Cx to monitor unit and inspect if any frost shows up. All defrost sensor show passed in diagnostic. Cx will call back if unit fails again."

Install suspension in Hub tested unit functions as designed.

"installed latch and control, tested, electrical supply fixed. Tested, unit functions as designed"

Upon arrival replaced sump motor assembly tested unit unit passed all tests job complete

Found the water to the unit I. The off position so the entire unit was not receiving water. I turned on the water and now the dispenser is getting water and the ice maker is as well. I advanced the ice maker and it called for water. Recommend leaving the unit on for several days and seeing if it continues with the ice production. Customer will call back with any issues.

After replacing all parts related to the ice maker I ran a cycle to check for leaks and none found. All tested ok. Customer will call back if issues persist. Job completed.

Found the unit had two error codes stored at this time. One was a f8e1 long fill and a f0e3 overloaded. I ran several diagnostic test with the valve and checked the pressure hose and all checked ok. Not to sure what caused the error but I removed the code and recalibrated the unit. After further inspection found the cold water valve in step on in diagnostics failed. It was receiving 122 but no water coming into the unit. I replaced the valve and all tested ok. I recalibrated unit again after repair.

After replacing all parts ordered the unit is operating properly. All functions tested ok. Job completed.

After replacing the slider and the rotor the unit is now able to rotate the basket and continue with the cycle. Job completed. All functions tested ok after repair.

Greeted cx cx said veggies would freeze and old unit have condition build up put old unit skid plate to remove small space remove old unit installed new unit pluged new unit in new unit worcking as designed

Found the suspension rods worn and the hub loose. Customer declined estimate for repair.

Replaced broken door switch and faulty evaporator fan motor. Unit ok after repair.

Replaced listed parts unit ok after repair. Original door was dented.

Thermistor not making good contact with harness. Reconnected thermistor.fridge working properly.

Replaced capacitor and ran diagnostic cycle.washer now working properly.

Installed filter.fridge working properly.

Tested hot and cold water valve and they are opening and closing as intended. Cx concern is that the tap cold is at a lower temperature at other water supplies in home even with washer functioning properly. Referred cx to GE cx service number 888-345-4671

Cx having trouble closing drawers but fridge is functioning properly.

Replaced pressure switch and found that leak is coming from water valve in wall and obstruction in drain.this is plumbing issue.

Replaced dispenser.dishwasher now working properly.

Ran ice maker diagnostics. Harvesting and filling properly at this time. Per customer ice maker not dumping cubes.

Replaced dog assembly and unit working per design. Job completed

Inspected unit and found missing serial tag. CX is going to contact whirlpool to get replacement tag then we can repair unit. Unit needs suspension rods and water valves when returned job complete for now.

Inspected unit and found belt not completely on pulley. Rubbing on guard. Unit now working per design. Job complete

Inspected unit and found major ice build up cleared ice out and advised Cx to check for water leaking into freezer building ice. Possible drain hole issues. Unit is cooling per design. Job complete

Inspected unit and found pulley worn causing belt to slip. Replaced pulley and unit passed all tests. Job complete. If recalled unit will need new belt.

Inspected unit and found Cx was having balance issues with the clothes. Machine passed all tests for me. Advised Cx about proper settings and loading. Unit working per design.

Unit had change in washplate binding and wedged in. Removed and unit passed all tests. Job complete

"Added wood block to floor under unit, adjusted leveling, tested door closing function, unit operating as designed, referred cx to WP for any cosmetic concessions ."

"Replaced center burner head, tested all burner functions, unit lighting & operating as designed."

"Replaced left side deli area led light module, tested all light functions, unit operating as designed; used 1 W10695459 (Led module) from stock"

"Checked the unit water dripping at the water valve and hose bib you would get with a install kit at Lowes , customer is going to get a new one and install it"

Removed old unit. Installed new unit. New unit operating as designed. Shaking and flow flat.

Installed new compressor and condenser. Recharged with 4.5oz or r134a. Unit is running without issue and beginning to cool. Parts and labor covered through limited warranty.

Installed new control and tested. Unit is now operating without issue.

Re established connection to infinite switch. All burners now coming on and heating with no issues.

Installed new parts. All functions now working as designed.

Installed new housing. All functions now working as designed.

Installed new board. All functions now working as designed.

"Fixed- installed new parts (3 coupling, 1 compressor) pressure tested, pulled vacuum - charged unit with 50 grams of r600a- unit has begun cooling, allow 12-24 hrs for temperature to stabilize- cx ok repair. A"

"Fixed- installed new parts (filter cup, wash motor) auto test pass- no leaks- no errors- unit working per design"

"Fixed- installed new parts (case, slider, rotor, agitator, clutch) calibration test pass- auto test pass- no leaks- unit now working per design- cx ok repair"

Installed door lock assembly. Recalibrated board tested unit operating properly.

"F7e4 basket re engagement failure , unit had bad actuator,replaced from truck stock and tested unit working as designed ; used 1 W10913953 (Actuator) from stock"

Installed new bezel and tested unit working as designed

"Customer didnt approve repair ,unit has bad control board"

Replaced belt and ran cycle. Unit passed all tests and is operating as designed.

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.