We serviced a
FRIGIDAIRE DISHWASHER
Model FGID2468UF
Near Palmdale, CA 93550
Jonathan
Job Details:
12/20/2021
Replaced defective ui and latch. Tested unit and is working properly
We serviced a
MAYTAG WASHER
Model MVWC565FW
Near Bakersfield, CA 93309
Patrick
Job Details:
12/20/2021
Unit not spinning. Checked errors. None stored. Checked level and the unit was wobbly. I leveled and checked suspension. Left front and right rear suspension rods not installed proper. Reinstalled and tested unit. All operations checked good
We serviced a
KITCHENAID RANGE
Model KSGG700ESS2
Near Los Angeles, CA 90049
Isidore
Job Details:
12/20/2021
"Found right side of door handle end cap, came off handle and door.Removed oven door, outer door panel and installed end cap too door handle and secured to outer door panel, on both sides.Reinstalled oven door, test oven operation.Range is is working at this time, as designed."
We serviced a
MAYTAG DRYER
Model MGD7230HW0
Near Los Angeles, CA 90049
Isidore
Job Details:
12/20/2021
"Found vent is a metal foil has obstruction and is torn, customer advised to have professional duct cleaning service correct and install rigid or flexible metal vent.Customer also advised that dryer should not be used as it is a fire hazard."
We serviced a
WHIRLPOOL ICE MACHINE
Model KUID508ESS1
Near Los Angeles, CA 90272
Isidore
Job Details:
12/20/2021
"Found water filter not working, customer has new filter install icemaker working at this time"
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DBL4
Near La Cañada Flintridge, CA 91011
Leon
Job Details:
12/20/2021
customer states that unit is not working properly After running diagnostic check find that wire harness is burned next to main board Disconnected wire for safety Parts W10909702l,.
We serviced a
WHIRLPOOL WASHER
Model WFW8620HC2
Near Los Angeles, CA 90272
Isidore
Job Details:
12/20/2021
"Removed top panel, old touch panel and installed new touch panel. Reinstalled top panel and test washer operation.Washer working at this time as designed."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LFSS2612TF
Near Visalia, CA 93291
J.E.
Job Details:
12/20/2021
Cycled and found unit not leaking. Customer concern is drip try does not stay in place. Explain to customer that drip tray just sits on there theres no screws or anything holding it. Unit is working as designed call tech line to document. Job completed sr#85068972.
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Camarillo, CA 93010
Isidro
Job Details:
12/20/2021
"On arrival I found a unresponsive unit or UI panel, called tech line to let them know about the on going issue with the UI panel giving out, was advised to change UI panel, tested unit, unit is now operating properly as designed at this time of service"
We serviced a
WHIRLPOOL WASHER
Model WFW6620HC0
Near Oxnard, CA 93036
Isidro
Job Details:
12/20/2021
"On arrival I ran diagnostics and couldnt find the noise, I advised the customer to record the noise its making, unable to find a problem with unit, unit is operating properly as designed at this time of service"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ11
Near Sanger, CA 93657
Timothy
Job Details:
12/20/2021
"Installed reservoir,control and FC door switch."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Templeton, CA 93465
Jack
Job Details:
12/20/2021
Customer states that this unit is really noisy. Ran a diagnostics test and checked out and calibration test. No codes and unit passed all the test. Unit sounds a little loader then some. It passed every test. Job completed
We serviced a
GENERAL ELECTRIC WASHER
Model GFW550SSN1WW
Near Morro Bay, CA 93442
Jack
Job Details:
12/20/2021
Found the unit didnt have power also. Checked and it was popping on and off. Checked for codes there were none other then a stuck key code. Ran cycle and unit works correctly. Cleared code. Job completed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Orange Cove, CA 93646
Timothy
Job Details:
12/20/2021
Customer has to leave the RC at its warmest setting or items in the unit freeze. Siliconed around the liner and replaced the thermistor and damper.
We serviced a
GE WASH/DRY COMBO
Model WCVH4800K2WW
Near Paso Robles, CA 93446
Jack
Job Details:
12/20/2021
Replaced locking assembly. Running test. Ran full cycle and unit is working correctly. Job completed.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LGHX2636TF
Near Dinuba, CA 93618
Timothy
Job Details:
12/20/2021
Found the filter is clogged. Used a bypass filter to test the water system.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Reedley, CA 93654
Timothy
Job Details:
12/20/2021
Installed actuator ordered last visit (in June) .Washer was unplugged upon arrival. Plugged in unit and it began to drain. Let unit drain for 5 minutes until it stopped. Checked for faults. None stored. Ran a service test and found the cold water was off. Turned on cold water and found the valve leaked. Tightened valve to stop the leak. This is the only place I could find a leak. The unit did not leak during the service cycle or when I started a normal load. Unit finished its service test without fault. Started a normal cycle and found the unit operating as designed .
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Riverbank, CA 95367
Timothy G
Job Details:
12/20/2021
Inspected unit and found ice tray popped out of holder. Reinstalled and unit passed all test..job complete.
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Santa Paula, CA 93060
Aaron
Job Details:
12/20/2021
"Checked operations. Found that the drain line is tapping up against the back wall and thats the Noises the customer was hearing. Secured drain line. Unit is working as designed "
We serviced a
WHIRLPOOL DRYER
Model WED9400SW2
Near Modesto, CA 95350
Timothy G
Job Details:
12/20/2021
Inspected unit and found idler wheel seized. Repaired with 4392067 kit. Job complete
We serviced a
KITCHEN AID REFRIGERATOR
Model KBSD608ESS01
Near Rancho Cucamonga, CA 91737
Jaime
Job Details:
12/20/2021
"Installed freezers drawers panel. Also, adjusted freezers door top hinge and spring it made noise when opening"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Riverbank, CA 95367
Timothy G
Job Details:
12/20/2021
Inspected unit found drain hose popped off of Phil tube. Reinstalled and unit pass all test
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW1
Near Rancho Cucamonga, CA 91701
Jaime
Job Details:
12/20/2021
"Ran diagnostics and there was no error codes stored. Checked functions, and washer meets factory specs"
We serviced a
MAYTAG DISHWASHER
Model MDB8969SDM0
Near Turlock, CA 95380
Timothy G
Job Details:
12/20/2021
Installed new adjusters and job complete.
We serviced a
MAYTAG DRYER
Model MGDC465HW0
Near Ontario, CA 91762
Jaime
Job Details:
12/20/2021
279311 ignitor. Replaced a shattered ignitor. Dryer ok; used 1 279311 (Ignotor) from stock
We serviced a
GENERAL ELECTRIC DRYER
Model GTD42GASJ2WW
Near Glendora, CA 91740
Jaime
Job Details:
12/20/2021
Black/yellow wire to doors switch came off. Reconnected wire dryer runs ok
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW2
Near Rancho Cucamonga, CA 91701
Jaime
Job Details:
12/20/2021
Checked washers functions and it meets factory specs. Washer A OK
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near Modesto, CA 95355
Timothy G
Job Details:
12/20/2021
Installed new shifter and clutch. Unit passed all testing. Job complete.
We serviced a
MAYTAG WASHER
Model MVW6230HW1
Near Modesto, CA 95355
Timothy G
Job Details:
12/20/2021
Installed new suspension rods and unit passed all tests. Job complete
We serviced a
MAYTAG WASHER
Model MVW7230HC0
Near San Dimas, CA 91773
Jaime
Job Details:
12/20/2021
Found rotors screw loose. Applied lock tide to screw and tighten it up. Retested washer and passed factory test
We serviced a
WHIRLPOOL RANGE
Model WFC150M0EW0
Near Oakdale, CA 95361
Timothy G
Job Details:
12/20/2021
undefined
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Oakdale, CA 95361
Timothy G
Job Details:
12/20/2021
Unit passed all test. Empty drum and spins fine. I believe Customer is having balance issue with clothes. Job complete
We serviced a
WHIRLPOOL COOKTOP
Model KFGU766VSS03
Near San Dimas, CA 91773
Jaime
Job Details:
12/20/2021
Had burners electrode cleaned. Then it worked ok. Charged 175.00
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Fontana, CA 92335
Tyler
Job Details:
12/20/2021
Connector is bad at drain pump. Removed and replaced harness tested all works good at this time.
We serviced a
KITCHEN AID OVEN
Model KOSE500ESS05
Near Rancho Cucamonga, CA 91737
Jaime
Job Details:
12/20/2021
Installed the convection fan motor
We serviced a
JENN-AIR RANGE
Model JGRP436HL00
Near Glendora, CA 91741
Bob S.
Job Details:
12/20/2021
Removed old unit installed new unit tested new unit operating as designed
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW0
Near Fontana, CA 92337
Tyler
Job Details:
12/20/2021
Customer stated that the unit is giving a long fill code. Cycle tested unit and found hot water valve not working. Found valve jammed. Fixed and tested all works good at this time.
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Pomona, CA 91768
Jaime
Job Details:
12/20/2021
Installed the striker. Washer works now
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Rialto, CA 92376
Tyler
Job Details:
12/20/2021
Customer stated that the unit is making noise in spin. Found belt is slipping. Removed and replaced belt tested all works good at this time.; used 1 W11239857 (BELT) from stock
We serviced a
WHIRLPOOL WASHER
Model LSR8233EQ0
Near Lake Isabella, CA 93240
James
Job Details:
12/20/2021
"Replaced defective motor, coupler and agitator dogs.Tested ok"
We serviced a
KITCHENAID OVEN
Model KODE500ESS04
Near Rancho Cucamonga, CA 91739
Tyler
Job Details:
12/20/2021
Customer stated that the unit popped fuse when using self clean. Removed and replaced fuses tested all works good at this time. Please bill out double labor for removal of unit.
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW1
Near Rancho Cucamonga, CA 91739
Tyler
Job Details:
12/20/2021
Customer stated that the unit worked one time. Found intermittent flame sensor. Removed and replaced tested all works good at this time.; used 1 338906 (]) from stock
We serviced a
GENERAL ELECTRIC RANGE
Model ZGP486LDN1SS
Near Apple Valley, CA 92308
Cesar
Job Details:
12/20/2021
Customer instruct on function and use unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Victorville, CA 92392
Cesar
Job Details:
12/20/2021
Found clogged softener dispenser causing water to aver flow when unit is dissecting softener. Cleared dispenser all tested good
We serviced a
GENERAL ELECTRIC DRYER ELECTRIC
Model GTX52GASP0WB
Near Lake Isabella, CA 93240
James
Job Details:
12/20/2021
Replaced defective idler pulley and lubricated Tested ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHZ1
Near Fontana, CA 92336
Tyler
Job Details:
12/20/2021
Removed and replaced sump tested all works good at this time.
We serviced a
JENN-AIR REFRIGERATOR
Model JFX2897DRM02
Near Victorville, CA 92395
Cesar
Job Details:
12/20/2021
Found failed freezer LED causing fresh food lights not to come on. Replaced LED ALL TESTED GOOD ; used 1 W10695459 (Pod) from stock
We serviced a
KITCHENAID RANGE
Model KFGG500ESS0
Near Wofford Heights, CA 93285
James
Job Details:
12/20/2021
Replaced defective user interface and tested.Tested ok
We serviced a
GE DISHWASHER
Model GDF530PGM6WW
Near Phelan, CA 92371
Cesar
Job Details:
12/20/2021
Found solenoid on water valve not fully seated causing water valve not to open
We serviced a
WHIRLPOOL REFRIGERATOR
Model MODEL
Near Hesperia, CA 92345
Cesar
Job Details:
12/20/2021
Sealed system failure compressor runs no frost pattern on evaporators unit has a leak decline at this time
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ05
Near Bakersfield, CA 93301
James
Job Details:
12/20/2021
Found unit with ice maker not functioning. Inspected and found power switch to ice maker had been hit and moved to a neutral position between on and off. Turned on ice maker and reset. Ice maker now working as intended. Ice maker harvested and filled as intended.
We serviced a
GENERAL ELECTRIC WASHER
Model gtw845cpndg
Near Bakersfield, CA 93311
Chase
Job Details:
12/20/2021
"Customers complaint that unit is getting out of balance. Received off balance error code. Cleared code and ran through calibration cycle. Tested unit, unit no longer getting off balanced and is now working by design. Job complete."
We serviced a
AMANA WASHER
Model NTW4516FW
Near Bakersfield, CA 93308
James
Job Details:
12/20/2021
Found unit with long fill error code and hot water valve turned off. Customer instruct on water level and loading techniques. Unit now working as intended.
We serviced a
MAYTAG WASHER
Model MHW8630HC4
Near Bakersfield, CA 93313
Chase
Job Details:
12/20/2021
Customer states that unit is not dispensing soap. Took apart dispenser and found path to valve clogged with detergent. Cleaned out dispenser assembly and housing. Ran through calibration cycle. Tested unit, all functions now checking out normal."
We serviced a
MAYTAG WASHER
Model MVW7230HC0
Near Bakersfield, CA 93313
Chase
Job Details:
12/20/2021
Customer states that hinge rubbing up. Adjusted hinge. Hinge no longer rubbing up. Instructed customer this is a normal design for it to rub up a little bit. All functions now checking out normal.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ04
Near Bakersfield, CA 93309
Chase
Job Details:
12/20/2021
Found foam blocking air path causing unit not to cool properly in FC. Remove foam and adjusted temperatures. All functions now checking out normal.
We serviced a
MAYTAG DRYER
Model MGD8630HC3
Near Bakersfield, CA 93313
Chase
Job Details:
12/20/2021
Found loose connection to moisture sensor not allowing unit to heat properly. Reconnected. All functions now checking out normal.
We serviced a
JENN-AIR COOKTOP
Model JGC7636BS01
Near Bakersfield, CA 93311
Chase
Job Details:
12/20/2021
Found loose gas line to valve connection. Corrected this issue and applied Teflon tape. All functions now checking out normal with no sign of any leaks.
We serviced a
WHIRLPOOL DISHWASHER
Model MDB4949SKZ0
Near Rosemead, CA 91770
Juan
Job Details:
12/20/2021
"F8e4. Customer is not using the proper inlet water hose, it is leaking at the inlet water valve connection. Water is leaking onto the float switch drain pan, activating the overflow switch. Unit is currently connected to a cold water source. Instructed customer to use the proper inlet water hose, and to connect the unit to a hot water source, for the unit to work properly."
We serviced a
WHIRLPOOL REFRIGERATOR
Model GD25DFXFB02
Near Bakersfield, CA 93309
Chase
Job Details:
12/20/2021
Installed new parts. All functions now checking normal. Job complete.
We serviced a
UNKNOWN RANGE
Model MODEL
Near Bakersfield, CA 93309
Chase
Job Details:
12/20/2021
Found two burner is not coming on. Took off element cleaned out connection and reconnected. All functions now checking out normal. Job complete.
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW1
Near Porterville, CA 93257
J.E.
Job Details:
12/20/2021
Cycled unit and found moisture sensor not connected causing unit to fail. Also level do you need for a customer. Secured connection and retested unit passed all test at time of service job completed
We serviced a
MAYTAG WASHER
Model MVW6230HW
Near Visalia, CA 93291
J.E.
Job Details:
12/20/2021
Cycled unit and found unit making very loud noise. Checked components and found drive pulley coming loose causing noise. Secured pulley and re-tested unit all test past time of service. Job completed
We serviced a
GENERAL ELECTRIC DRYER
Model UKNW
Near Visalia, CA 93291
J.E.
Job Details:
12/20/2021
Cycled unit and found unit not heating at all. Checked components and found heating element had a connection issue. Secured connection and re-tested unit all test pass the time of service. Job completed
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Visalia, CA 93291
J.E.
Job Details:
12/20/2021
Cycled unit and found unit not leaking. Fully inspected unit for leaks no signs of water. Customer states it was a very small leak and only Happened once. Unit is not leaking and working as designed. Job completed
We serviced a
MAYTAG WASHER
Model MVWB865GC1
Near Lindsay, CA 93247
J.E.
Job Details:
12/20/2021
Cycled unit and found unit not powering on. Check components and found loose connection to UI. Causing unit to fail. Secured connection and re-tested unit all test pass at time of service. Job completed.
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Visalia, CA 93292
J.E.
Job Details:
12/20/2021
Cycled unit and found unit not shifting properly. Checked components and found loose connection to shifter causing unit to fail at times. Secure connection and re-tested unit passed all test at time of service. Job completed
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US
Near Porterville, CA 93257
J.E.
Job Details:
12/20/2021
Cycled unit and found unit not starting. Checked components and found loose connection to control board causing unit fail. Read tested unit passed all test a towel service. Job completed
We serviced a
MAYTAG DRYER
Model MED6230HW0
Near Visalia, CA 93277
J.E.
Job Details:
12/20/2021
Cycled unit and found unit working as designed. Fully tested unit all tests passed. Instructed customer on properly loading and cycle selection. Job completed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ05
Near Modesto, CA 95357
Cruz
Job Details:
12/20/2021
Customer states water from dispenser and ice cubes do not taste right- I then test water and found it to be clear look at pictures- water filter has been changed out per customer- flush system out (8 cups) per whirlpool- other solution is to add a copper water line per whirlpool- cooling and temps are working fine.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Turlock, CA 95382
Cruz
Job Details:
12/20/2021
"Fixed for fcc- error code f8e4 possible leak- removed kick plate and found water leaking from brass elbow to inlet valve- i then tighten brass elbow removed water from drip tray- tested the appliance in a diagnostic test mode it completed filled, wash, drain, heated, no leaks from brass elbow- no error codes- customer ok repair."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FGHG2368TF2
Near Modesto, CA 95355
Cruz
Job Details:
12/20/2021
Rodney from Frigidaire tech line- need to get thinner wire leads- my wire leads are too big will fit into connector- customer is still having intermittent issues with ff compartment freezing food and drinks- damper test pass in diagnostic- Frigidaire thinks there might be a air leak somewhere- Frigidaire want to get resistance checks from damper harness- cooling and temps are working fine at this time-
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB01
Near Modesto, CA 95351
Cruz
Job Details:
12/20/2021
"Fixed for fcc- found damper to be iced over- damper is stuck open causing food, drinks to freeze over- removed bad one and then installed new one (diffuser) damper is opening/closing as designed- customer ok repair"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ
Near Tulare, CA 93274
J.E.
Job Details:
12/20/2021
Installed new parts and re-tested unit all test pass the time of service. Job completed
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Visalia, CA 93292
J.E.
Job Details:
12/20/2021
W 03 affected-Special Project S17304 Heater Bushing W11537778 Parts and Labor. Installed new updated heater and tested unit passed test at time on
We serviced a
WHIRLPOOL DRYER
Model WGT4027HW1
Near Rancho Cucamonga, CA 91739
Bob S.
Job Details:
12/20/2021
Removed old unit hauled off for scrap
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Modesto, CA 95355
Cruz
Job Details:
12/20/2021
Fixed for fcc- found top rack adjusters to be broken causing rack to hang down causing door not to close properly- removed bad ones and then installed new ones (adjusters) top rack is now rolling in/out as designed- door is now closing properly as well- customer approved repair.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW
Near Kingsburg, CA 93631
Timothy
Job Details:
12/20/2021
House venting severely restricted. Element open. Instructed customer to get this fixed ASAP because of the possibility of more damage to the unit or fire. Unit checks ok. Vent restricted.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ12
Near Grand Terrace, CA 92313
Jim
Job Details:
12/20/2021
Removed shipping tape from the back wall. Leveled and locked the legs. Moved the condenser away from the ceiling to prevent vibration noise.
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC0
Near San Bernardino, CA 92410
Jim
Job Details:
12/20/2021
Replaced user interface and unit tested ok
We serviced a
GENERAL ELECTRIC DRYER
Model GTD42GASJ2WW
Near Apple Valley, CA 92308
Drew M.
Job Details:
12/20/2021
Replaced parts and ran cycle. Unit passed all tests and noise is gone.
We serviced a
WHIRLPOOL RANGE
Model WFG515S0JS1
Near Calabasas, CA 91302
Joe
Job Details:
12/20/2021
"Unit is displaying that it cannot reach a temperature above 100 found igniter ignite but unit is not getting enough gas. The only other things that can cause this would be a control or sensor if customer keeps having issue we will replace control and sensor, at this moment, calibrated system, tested, unit opas as deasign"
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0HB02
Near Calabasas, CA 91302
Joe
Job Details:
12/20/2021
Found that the power supply to the bake element had touched the metal cavity causing unit to short every time its plugged in. Replaced terminal unit is functioning as designed job complete
We serviced a
WHIRLPOOL DRYER
Model MGD5500FW1
Near Tulare, CA 93274
Enrique
Job Details:
12/20/2021
"Customer concerns, dryer not drying completely on sensor cycles. In diagnostics found, f3e6- moisture sensor open. Installed new sensor (truck stock), ran normal dry cycle, used wet towel. All functions worked as designed at time of service.; used 1 WPW10298258 ( Moisture sensor) from stock"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ04
Near Simi Valley, CA 93063
Joe
Job Details:
12/20/2021
Found unit is not dispensing ice. On inspection found unit is not dispensing ice due to the ice in being shoved in unit crooked. Corrected ice bin and unit began to function as designed job complete
We serviced a
GENERAL ELECTRIC DRYER
Model GTDP520GDWW
Near Tulare, CA 93274
Enrique
Job Details:
12/20/2021
"Customer concerns, dryer not tumbling. Belt came loose from motor. Reinstalled belt, ran test. All functions worked as designed."
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS
Near Visalia, CA 93291
Enrique
Job Details:
12/20/2021
"Customer concerns, ice maker stopped making ice. Found frozen fill tube. Removed frost, ran test #57 & #45 . All functions worked as designed, no leaks."
We serviced a
GENERAL ELECTRIC GAS RANGE
Model JGB735SP1SS
Near Hanford, CA 93230
Enrique
Job Details:
12/20/2021
"Customer concerns, range burners sometimes look orange. Burners flame were too high. I adjusted the flames, tested all burners . At time of service, flames were blue ( took quick pics )."
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW0
Near Los Angeles, CA 91344
Joe
Job Details:
12/20/2021
Replaced rods and tested unit job complete
We serviced a
MAYTAG WASHER
Model MVW6230HC2
Near Calabasas, CA 91302
Joe
Job Details:
12/20/2021
Customer complaining about unit shaking during use. Found error code for off balanced load. Ran diagnostic test found machine to work fine informed customer to not overload unit. Customer is also complaining about her water lines vibrating when the units water valve calls for water this is normal function
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ11
Near Simi Valley, CA 93063
Joe
Job Details:
12/20/2021
Units damper control wasnt closing enough so the unit was freezing food. Replaced damper unit is functioning as designed job complete
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Tulare, CA 93274
Enrique
Job Details:
12/20/2021
"Customer concerns, washer not responding to start wash cycles, keeps making grinding noise. In diagnostics found, oversuds and also belt making very loud squeaky noise. Performed calibration, installed new belt ( truck stock ). All functions tested normal, no leaks.; used 1 WPW10006384 ( Belt) from stock"
We serviced a
MAYTAG WASHER
Model MVWB855DC3
Near Lancaster, CA 93535
Jonathan
Job Details:
12/20/2021
"Found loose connection to valve, fixed connection, tested unit and is working properly"
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Palmdale, CA 93551
Jonathan B.
Job Details:
12/18/2021
JB Out 12/18/21 customer says while washing machine is filling with water it makes a high-pitched squealing sound intermittently. Tested washer in normal cycle. Verified intermittent high-pitched whining noise caused by defective Cold water faucet. Unable to adjust faucet. Customer will need to replace cold water faucet. Tested washer operation with customer. Unable to verify any other mechanical issues. No parts used. No charge to customer. Job complete
We serviced a
CROSLEY WASHER
Model VAW3584GW1
Near Lancaster, CA 93535
Jonathan B.
Job Details:
12/18/2021
JB Out 12/18/21. Found water inlet valve assembly cracked. Installed at water valve part number W11210459. Reassemble. Customer will connect water supply hoses to washing machine. No charge to customer. Job complete
We serviced a
ELECTROLUX DRYER
Model EIMGD55IIW2
Near Bakersfield, CA 93312
Erick
Job Details:
12/18/2021
"Kb@philbranch.comInstalled new parts on unit, re-tested it and unit is now heating and cycling with no faults. Job complete"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Bakersfield, CA 93314
Erick
Job Details:
12/18/2021
Attempted to install new board but board not responding. Found it to be defective. Customer decided not to move forward with repair at this time. Job complete
We serviced a
WHIRLPOOL RANGE
Model JJW9830DDP
Near Bakersfield, CA 93314
Erick
Job Details:
12/18/2021
Install new parts on unit. Re-tested it and unit passed all test with no errors at the time of service. Job complete
We serviced a
MAYTAG REFRIGERATOR
Model MFI2067ABW
Near Bakersfield, CA 93312
Erick
Job Details:
12/18/2021
Installed new parts on unit. Retested it and unit passed all tests at the time of service. Job complete
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF707ESS01
Near Bakersfield, CA 93314
Erick
Job Details:
12/18/2021
Installed new parts on unit. Set temperatures back to factory settings. Units is cooling in both sections. Job complete