"Top drawer on unit was misaligned, reinstalled top rack and unit is now working as designed, job complete"

"Ran diagnostics and found F5E4 F7E4 error codes. Found failure in the actuator, cam and belt worn out. Replaced belt, cam, and actuator. Ran cycle and unit passed all tests. Unit is now operating as designed.; used 1 W10913953 (Actuator), 1 W10721967 (Cam), and 1 W11239857 (Belt) from stock"

"Found effective door lath, replace door latch tested unit is working"

Unit wont driain. Throws code. Removed and replaced pump n motr cleared drain now working as designed

Replaced gaskets. Heatre treated job complete.

"Remove the from tub, and install the new out front tub. Retest the unit and now unit doesnt have any leaks. Job complete Maintenance is going to stack the dryer back on place."

"Replaced all parts, unit is now not making noise. Or normal noise. Temp is heating, unit is working as designed, job complete."

Found the basket not spinning freely and getting hung up on the slider. I replaced the slider and verified operation and all functions are now working as designed. Job completed. ; used 1 W10734521 (Slider) from stock

Customer concerns: washer not spinning water out. F9E1 fault. Removed obstruction from drain pump. Initiated drain & spin cycle. Washer operating as designed. No leaks.

UI has failed. Replaced UI. Unit operating as designed. Job complete.

Installed part tested check out ok complete no dents or dings cause by tech.

Installed parts tested check out ok complete no dents or dings cause by tech

Customer says all loads go off balance despite carefully loading washer. Unit was not leveled. Leveled and tested unit. Unit operating as designed. Job complete.

Installed motor and fan tested working properly

Replaced faulty compressor and leaking evaporator. Vacuumed and charged to spec. Unit ok after repair.

Found faulty lid latch. Removed and replaced parts . Retested it and it passed all tests . Job com

"Unit has no drive motor function, locked rotor at start up , Replaced drive motor, ran test dry cycle, unit operating as designed."

Replace defective cap tested unit is working properly

Customer concerns: high flame on range cooktop. Needed burner conversion orfices to propane. Parts came with range.

Found a small ice cubes and also icemaker was leaking had icemaker valve replaced

Replaced ACU Unit working properly as required

Customer states that unit is not working properly After running diagnostic test find that shield cover was out of position Remove and reinstalled shield cover properly Unit working properly as required

Customer states that unit is not heating up properly After running diagnostic test find that airflow hose was kinked Remove and reinstalled airflow hose properly Tested unit working properly as required

Installed new repair kit and cleaned roller posts. Tested and unit is now working as intended.

Found unit with loose wire nut reinstalled tested working properly

Freezer door not sealing due to blockage. Removed blockage and door is sealing as intended.

"Replaced the control, and valve. Restored power programmed board, passed. All ops good. DONE."

"Customer was having defrost issue. Put unit into diagnostic mode. Compressor, Evap fan and condenser fans operational. Heater turns on during diagnostic mode. Defrost issue cause by improperly installed heater. Heater extension was not in drain causing ice plug and water to spill out of front of freezer. Properly installed heater extension into drain. Unit operating as designed. Job complete."

Found loose wire to timer also unit has vent restriction needs venting cleaned

"Installed new ice maker and tested unit, working as designed"

Removed and replaced pump. Now working as designed

Installed parts tested check out ok complete no dents or dings cause by tech.

Install a News lighter on the washing machine worked OK; used 1 W10734521 (Slider) from stock

Replaced faulty pressure sensor and main control in order to fix f3 e1 error. Tested after repair all ok.

"Customer says the DW just installed is not draining. Standing water in the unit. Customer informed me the disposal was replaced prior to the new DW. checked the disposal, the knock out was not removed. Corrected the issue. Cleared error codes, ran test cycle passed. All ops normal. DONE."

Customer states that unit is not working After running diagnostic test get error code F8E4Replaced water level switch Unit working properly as required

Inspected unit and found door not closing all the way. Adjusted hinges and unit is now working per design.

"Replaced pressure sensor. Cleaned air trap, pump filter. Cleared error codes. Locks/ unlocks, fills, washes, drains, rinses, dispenses, and spins properly at this time. Advised customer to run clean cycle with affresh cleaner 2 times before using washer. Complete."

"Removed and rpqlced new compressor. Pulled vacuum, recharged system, inspected for leaks and found none. Unit is now cooling job com"

Installed part tested check out ok complete no dents or dings cause by. Tech.

Installed door tested working properly

Ran cycle and unit did not heat up. Found 240v across L1 and L2. Power was good. Opened unit and found a connection to the high limit thermostat hanging off. Reestablished the connection and ran cycle. Unit heated up and passed all tests. Unit is now operating as designed.

"Replaced cooktop, tested all burner functions, unit operating as designed."

Replaced all selected parts Unit working properly as required

"Found actuator and drive pulley bad replaced tested working properly ; used 1 W10913953 (ACTUATOR), and 1 W10721967 (DRIVE PULLEY) from stock"

Found long fill code tested unit found failed #1 cold water valve has power not fully opening. Replaced valve all tested good ; used 1 W11316256 (Valve) from stock

"Found the unit, not cooling, verify problem compressor not working, replaced compressor,service valve and cntrl-elec, charge nitrogen not verify leaks, make a vacuum, charge refrigerant 4.50 oz R134a, check compressor,condenser and evaporator fan motors unit work normal"

"Returned, replaced defective partsdesigned operation was restored"

Replaced valve. Refrigerator operating as designed. No leaks.

Upon arrival found unit with rack falling down this because one of the wheels on the left side is broke. Replace the adjuster kit on the unit. Retest the rack and now everything is working properly. Job complete.

Installed new mullon. Also tighten all handles. Job complete.

Nut spanned and gear case were removed and replaced. Unit is working as intended. Job completed.

Replaced burner cap and flame spreader.cooktop working properly.

Install the new glass on the unit. Job complete.; used 1 WPW10188327 ( Glass) from stock

Fixed- installed new parts ( 2 cntrl elrc) all lights are now working per design- customer ok repair

"JB out 11/10/23.Customer states unit shakes and vibrates badly every cycle, during wash (tumble) portion and especially in the spin portion of the cycle. Verified unit has been installed on the CORRECT pedestal intended for this model Washer/Dryer combo.Also verified Unit is level and the shipping bolts have been removed. However, the installer neglected to remove the (2) Brackets on the rear of the washer as outlined in the provided Installation Instructions.Ran diagnostics, specifically test #11 (Spin) without clothes in the wash tub and verified proper spin operation. No shaking even at highest spin speed.Spoke with Corey at GE TAG WHO CONFIRMED THE TWO BRACKETS ON THE REAR OF THE MACHINE SHOUD BE REMOVED AND THE (4) washing machine feet SHOULD BE INSTALLED TO INCREASE STABILITY. INSTALLER DID NOT INSTALL THESE FEET AND ARE NOT HERE. REFER CUSTOMER TO INSTALLER TO RETURN AND CORRECT INSTALLATION.PER GE, THE 4 Bolts and Spacers MUST BE REINSTALLED BEFORE TILTING OR TIPPING WASHER OR SUSPENSION SPRINGS WILL BECOME DISLODGED. Installer must return to correct the installation. The four missing washing machine feet must be installed between the washer, and the pedestal tightened between the washer and pedestal and the lock that must be tightened as well for each of the 4 feet. Installation corrections are not covered under the General Electric, manufactures warranty, and the responsibility for correctly Escalation falls upon the installer. No charge to the customer. No Parts used. Job complete."

"Installed belt, rollers and idler, tested unit functions as designed."

Swapped out unit control board. Unit is no longer shutting off prematurely. Job complete.

Fixed- found ice maker to be slowing down on ice production- temperature @ 2°- installed new (ice maker) ice maker harvest and water filled mold- allow 12-24 hrs for ice production- customer ok repair

Replaced cracked blower wheel and motor mount. Tested after repair all ok. No more loud noise.

Installed new UI and retested unit now working as designed job completed

"Checked the unit the slider was separating, replaced the slider , customer has coins in basket, tested ok now at this time"

Removed and replaced pump n motor n sensor. Tested now working as designed.

Thermostat was removed and replaced. Unit is working as intended.

Ice maker was removed and replaced. Unit is working as intended. Job completed.

Icemaker bail arm was making contact with tray and causing it to stop the harvest. Replaced with preID icemaker. Unit now working as designed.

Cycle unit and found unit working as designed informed customer of finding. Job completed

Replaced thermal cutoff and thermal fuse.dryer working properly.

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

"Checked the unit , dampener is noisy , replaced the dampener asm , tested ops ok now at this time"

"Unit was not draining, had error code F9E1, F8E6. Checked drain pump and noticed cable had came off. Reinstalled connection and unit began to drain. Cleared out error codes, calibrated unit, and ran diagnostics. Unit is now working as designed, job complete"

Found broken door switch replaced switch tested unit dryer is tumbling and heating properly Job complete

Installed start relay and tested unit working as designed

Installed part tested check out ok complete no dents or dings cause by tech.

Air channel going to fresh food section was iced up not allowing air in removed ice air is flowing properly Job complete

Installed drain hose. All functions tested okay no leaks found after parts installed. Unit working as designed. Call complete

Heating element was removed and replaced. Dryer is working as intended. Job completed

Cleared plugged defrost drain. Heater and thermal fuse ohm out ok. Drain is flowing properly at this time. Unit is cooling properly at this time. Instructed customer to allow 24 hours before loading food. Complete.

Light switch arrived broken for client. Not cosmetic issue. Functional problem. Removed and replaced switch now working as designed

Installed brackets.

"Used water tube, cleared drain, tested, unit functions as designed."

"Installed difuser, tested, unit functions as designed."

"Middle spray arm asm came apart, replaced it with a new one, operations ok now at this time"

Installed part tested check out ok complete no dents or dings cause by tech.

"Removed and replaced compressor. Pulled vacuum, recharged system, inspected for leaks and found none. Unit is now cooling job com"

Installed new lid retested unit now working as designed job completed

Unit not cooling in both compartments. I found locked up compressor causing no cool. Removed and replaced compressor. Vacuumed system down and charged with r600. All tests good.

"Because of a heavy leaking at the doors bottom, a new bellow gasket has been replaced."

Replaced evaporator motor and harness. Refrigerator operation checked normal at time of service. Customer will allow 24 hrs to confirm refrigerator works.

Door was not opening right. Found foot pedal loose. Secured foot pedal and tested unit. Unit functions normal now.

Found after replacing the suspension kit the suspension test now passed but the belt is making a squealing noise. After replacing the belt the unit no longer makes the squealing noise. All other functions are working properly Job completed. ; used 1 W11239857 (Belt) from stock

Found the high temp alarm on. Found temp at 38 degrees in fresh food. Reset alarm. Display went to 37. Unit functions normal now.

"Checked temps, found 0 & 38 degrees, unit producing ice now, unit operating as designed."

Found failed door switch stuck in the closed position replaced switch all tested good

Unit not going into defrost. Defrosted unit. Removed and replaced control and thermistor and turned defrost heater on. Unit functions normal now

Replaced drain tube Unit working properly as required

"Because of an error code F1 E2, a new clock board has been installed."

Left front burner was not igniting. Spark would sound and work but spark connection was broken. Replaced orfice and unit is now working as designed job complete.

Installed new ice guide and retested unit now working as designed job

Found pulley making sound. Removed and replaced pulley and tested unit. Unit functions normal now.