Near Fresno, CA 93722
Irvin
Job Details: 05/07/2019
LAUNDRY MAYTAG MVWB765FC3 "F0/E3- over load F8/E1-long fillUnit not completing cycles. Found the water supply for hot was off. Screens are clear. Test the valve water supply good. Connected hoses, turned in water. Water is flowing. CX INSTRUCT,HOT WAS OFF CAUSING ISSUE. LEAVE HIT WATER KN ALL THE TIME."
Near Oxnard, CA 93033
Hector Zuleta
Job Details: 05/07/2019
REFRIGERATOR WHIRLPOOL WRT111SFDM03 Refrigerator leaking through the supply/return air vents.I checked the unit and found the drain hole iced up. Manually defrosted and installed a heat probe. Tested ok.; used 1 819043 (HEAT PROBE) from stock
Near Camarillo, CA 93012
Hector Zuleta
Job Details: 05/07/2019
WASHER WHIRLPOOL WTW7300DW1 Unable to close completely the detergent drawer dispenser. I checked the detergent dispenser and it was stuck. Adjusted dispenser drawer. Tested ok.
Near Camarillo, CA 93012
Hector Zuleta
Job Details: 05/07/2019
OVEN WHIRLPOOL WOS92EC0AS03 "Replaced open thermal fuse and door gasket, also recalibrated. Tested ok."
Near Camarillo, CA 93010
Hector Zuleta
Job Details: 05/07/2019
DRYER MAYTAG MGDX655DW2 Hard to open or close the door. Replaced the catch and strike.also lubricated. Tested ok.
Near Oxnard, CA 93035
Hector Zuleta
Job Details: 05/07/2019
WASHER WHIRLPOOL WFW92HEFW0 "Washer not dispensing hot water. I set unit in diagnostic and found an F8E1 code (No water detected entering the washer, or water level sensor trip not detected).Removed top panel and found hot water solenoid unplugged, reconnected and tested ok."
Near San Luis Obispo, CA 93401
George
Job Details: 05/07/2019
WASHER WHIRLPOOL WFC7500VW2 Found washer not draining replaced drain pump tested check out ok complete. No dents or dings cause by tech.
Near San Luis Obispo, CA 93401
George
Job Details: 05/07/2019
REFRIGERATOR FRIGIDAIRE FFSS2615TS Installed parts tested check out ok complete. No dents or dings cause by tech.
Near Nipomo, CA 93444
George
Job Details: 05/07/2019
DRYER ELECTROLUX EFMG627UTT Found dryer working ok possibility clothes still to wet wen putting into dryer check air flow ok getting hot ok complete. No dents or dings cause by tech.
Near Covina, CA 91722
Andy
Job Details: 05/07/2019
RANGE JENN-AIR FCG20510B "Needs igniter ; ordrng 1 12400035 (igniter,oven)"
Near Lindsay, CA 93247
Erick
Job Details: 05/07/2019
FREEZER FRIGIDAIRE LFTR1814LB "Cycled unit and found unit with the sensor out of alignment which caused less cool time. Re installed and secured sensor. Set temperature to proper setting,fans is now running and unt is coo,in eith no errors. Job completed"
Near La Puente, CA 91744
Andy
Job Details: 05/07/2019
REFRIGERATOR KITCHEN AID KRMF706ESS01 No cool; ordrng 1 W10832994 (compressor) and 1 WPW10608485 (evaporator)
Near Delano, CA 93215
Erick
Job Details: 05/07/2019
WASHER MAYTAG MVWX700XL1 Cycled unit and found unit with pressure fault error. Found kink in hose causing failure. Removed and straighten hose. Recalibrated main control. Retested it through diagnostics and it passed all tests with no errors. Job completed If issue persists please order new control and cold valve. Job completed
Near Bakersfield, CA 93314
Erick
Job Details: 05/07/2019
REFRIGERATOR WHIRLPOOL WRX988SIBM01 Cycled uni and found unit with deli board not reading . Main control is not reading temp in deli which may be causing failure. Accessed control and re secure pin and to control. Re powered unit back on and deli board is now sending powering and sending signal back to control. Set temp to correct settings. If issue persists will need new deli door assembly. Job completed
Near Bakersfield, CA 93312
Erick
Job Details: 05/07/2019
DRYER WHIRLPOOL WGD7500GW0 Installed new gas burners. Retested unit. Unit cycled and heated with no gas or errors. Job completed
Near Bakersfield, CA 93305
Erick
Job Details: 05/07/2019
DRYER ROPER RGD4516FW Cycled unit and found 7nit not heating due to bad thermal fuse. Retested it and it no powers on. It cycled and heated. Job comp
Near Apple Valley, CA 92308
Darren
Job Details: 05/07/2019
DRYER MAYTAG MEDB835DW3 "Found noise to be idler pulley bushing failure, rollers and belt check okay, replaced pulley wheel and tested, checks out good.; used 1 4392067 (DRYER REPAIR KIT) from stock"
Near Hesperia, CA 92345
Darren
Job Details: 05/07/2019
LAUNDRY MAYTAG MVWB765FW1 "Checked unit for codes, no codes found, unplugged unit and tested, buttons working normally after resetting unit"
Near Bakersfield, CA 93308
Erick
Job Details: 05/07/2019
WASHER WHIRLPOOL MHW3505FW1 Found unit with f301 error indicating pressure fault. Cleared pressure hose and resecured connectors at pressure switch. Reprogram main control. Retested it through test cycle and it passed all tests with no errors. Job completed
Near Fresno, CA 93720
Chris
Job Details: 05/07/2019
REFRIGERATOR WHIRLPOOL WRF550CDHZ00 Customers issue is the temperature in the refrigerator was warm. On arrival I found thermostat was set as low as it can go and then in the freezer it was set to +3°. I went ahead and change the thermistor and set temperature to proper settings. All functions Are testing good Temperature in refrigerator was about 35° . Job complete
Near Clovis, CA 93612
Chris
Job Details: 05/07/2019
DISHWASHER FRIGIDAIRE FBD2400KW12B On today’s visit replaced the float and switch for dishwasher. Then cycle dishwasher on make sure there was no leaks . Everything checks out good. Job complete
Near Fresno, CA 93730
Chris
Job Details: 05/07/2019
DISHWASHER KITCHENAID KDTE234GPS0 Customers issue is that top rack of dishwasher kept on falling forward. I found the problem was the dishwasher was leaning forward way too much. I adjusted the legs to level the Dishwasher. Then tested upper and lower Rack. All functions tested good now customers happy. Job complete
Near El Monte, CA 91732
Andy
Job Details: 05/07/2019
RANGE WHIRLPOOL WFG515S0ES1 Replaced burner caps per techline
Near Tracy, CA 95376
William
Job Details: 05/06/2019
WASHER WHIRLPOOL WFW92HEFC0 "Replaced inner door glass & pressure sw., ran self diagnostics , error F8E0, instructed cx there is no hot water supply to washer. Have hot water restored to washer before continuing to use washer."
Near Tracy, CA 95304
William
Job Details: 05/06/2019
RANGE KITCHENAID KFGD500ESS04 "Found upper door gasket with detached clips, Replaced upper oven door gasket, reinstalled upper door, testedok"
Near Patterson, CA 95363
William
Job Details: 05/06/2019
WASHER WHIRLPOOL WFW72HEDW0 "Replaced leaking bellows, ran test cycle, checked for leaks, no leaks found"
Near Ripon, CA 95366
William
Job Details: 05/06/2019
DRYER WHIRPOOL MEDB765FW0 "Cx having keypad issues, Replaced main control brd, checked keypad functions, tested ok"
Near Modesto, CA 95354
William
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDF560SAFM2 "No codes found, ran diagnostics cycle, heater tested ok, instructed cx on rinse aid & drying dishes. Unit operating as designed"
Near Pomona, CA 91767
Tyler
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW8500DW0 Customer stated that the unit will not turn anymore. Found error codes for motor overheat and temp sensor fault. Found rotor was melted to drain pan. When replacing the rotor the shaft is stuck inside the gear case. Removed and replace gear case rotor and fill valve. Tested all works good at this time.
Near Modesto, CA 95355
William
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDT730PAHZ0 "Replaced rack end stops, found debris in airgap, unplugged airgap, ran self diagnostics cycle, unit operating as designed."
Near Pomona, CA 91767
Tyler
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW7500GC0 Customer stated that the unit was not spinning and has a long full error code. Check units error codes and found error code for temp sensor fault in spin and communication error. Removed and replaced control board and fill valve tested all works good at this time.
Near Claremont, CA 91711
Tyler
Job Details: 05/06/2019
OVEN KITCHEN AID KODC304ESS00 Customer stated that the oven shows and error code for a shorted temp sensor in the lower oven. Removed and replaced temp sensor and main control. Tested all works good at this time. Customer paid for sensor labor and service call. Please S code main control.
Near Claremont, CA 91711
Tyler
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRF757SDEM01 Customer stated that the refer is not cooling. Found evaporator is frozen over. Removed and replaced thermistor fan kit tested all works good at this time.
Near Rancho Cucamonga, CA 91737
Tyler
Job Details: 05/06/2019
ICEMAKER KITCHENAID KUIX305ESS2 Removed and replaced drain pump. Tested all works good at this time.
Near Fontana, CA 92336
Tyler
Job Details: 05/06/2019
DRYER WHIRLPOOL WGD7500GC Customer stated that the dryer takes too long to dry. Found vent restriction is causing long dry times. Calibrated unit and customer to have vent cleaned. All works good at this time.
Near Upland, CA 91784
Tyler
Job Details: 05/06/2019
REFIRGERATOR WHIRLPOOL WRF540CWHZ01 Customer stated that when he first got the unit he had a leak but hasn’t leaked since. Cycled ice maker and checked dispenser. No visible leaks at this time. All works good at this time.
Near Pomona, CA 91768
Tyler
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW5000DW1 Customer stated that the unit was not completing cycles. Found pump has voltage but is jammed. Removed and replaced pump. Tested all works good at this time.; used 1 W10876600 (PUMP-WATER) from stock
Near Upland, CA 91784
Tyler
Job Details: 05/06/2019
DRYER WHIRLPOOL WGD4815EW2 Customer stated that the timer knob broke off. Found shaft for timer broken. Removed and replaced timer tested all works good at this time.
Near Upland, CA 91784
Tyler
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDT970SAHZ0 Customer stated that dishwasher is not draining. Found clogged air gap. Fixed and calibrated all works good at this time.
Near Rancho Cucamonga, CA 91739
Tyler
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRX988SIBM01 Customer stated that the refer is not cooling in both compartments. When I arrived the lights were on but no activity from compressor or fans. Unplugged unit and plugged back in. Compressor and fans came on and frost pattern is visible. Removed and replaced controls. Tested all works good at this time.
Near Atascadero, CA 93422
Tom
Job Details: 05/06/2019
DISHWASHER KITCHEN AID KDTE704DBL0 "Found unit unable to start, reprogrammed unit, test okay. No damage to unit or home from tech, job complete."
Near Modesto, CA 95355
William
Job Details: 05/06/2019
FREEZER KITCHENAID KRMF706EBS01 "Found ice in freezer & ice at bottom of FF area ordered adapter kit for unit, instructed cx to defrost unit,; ordrng 1 W10864519 (adapter)"
Near Templeton, CA 93465
Tom
Job Details: 05/06/2019
DRYER WHIRLPOOL GEW9250PW1 "Installed Dryer Repair Kit, test okay. No damage to unit or home from tech, job complete."
Near Paso Robles, CA 93446
Tom
Job Details: 05/06/2019
REFIRGERATOR WHIRLPOOL WRS325SDHZ01 "Found refrigerator operating normally with optimal level of noise and vibration. Gap on left side of refrigerator to wall, suggested to customer insulating part of gap can reduce noise traveling from behind refrigerator, but not to stop air flow from behind unit."
Near Turlock, CA 95382
William
Job Details: 05/06/2019
MICROWAVE JENN-AIR JMC2430DP01 "F2E1, Replaced UI panel, programmed panel, new code after UI panel install error F6E6, ACU1 lost communication, ordered UI panel & ACU brd.; ordrng 1 W10815465 (cntrl-elec) and 1 W11229663 (panl-cntrl)"
Near Cambria, CA 93428
Tom
Job Details: 05/06/2019
REFRIGERATOR FRIGIDAIRE FFSS2615TS0 "Upon arrival, found IM making ice, full harvest, full bin. Customer concerned about too much ice production, customer instruct on ice maker functions. No ice maker arm flag for this model found to change IM arm detection more sensitive, customer instruct. No damage to unit or home from tech, job complete."
Near Atascadero, CA 93422
Tom
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW7500GW0 "Found error codes F0E3, F7E8, F9E2. Customer showed tech load that was last put in, large amount of towels, too heavy of a load. Error codes in sequence show and overload, rotor overheating, and drain issue, caused by large load and unit moving across floor. Cleared codes, ran diagnostic test, ran load calibration, test okay, no codes. Visual of basket in high speed optimal, no sway in basket. Customer instruct for load size and weight, also passed info to household personnel. No damage to unit or home from tech, job complete."
Near Manteca, CA 95337
William
Job Details: 05/06/2019
KITCHEN KITCHENAID KDTE104ESS1 "F7E1, ran diagnostics cycle, no heater functions, soap dispenser door gasket slipping out, ordered control, heater & soap dispenser; ordrng 1 W10703867 (heater) and 1 W10854225 (cntrl-elec) and 1 W10861000 (detergent dispenser)"
Near Fresno, CA 93722
Timothy
Job Details: 05/06/2019
WASHER GE HTW240ASK4WS Knocked on door after speaking with maintenance. No one answered even though the sliding door was open. Knocked and waited for 10 minutes. Maintenance showed up and knocked and the person inside answered. I was in front of the door and no one entered. Started working on the unit. Checked for faults. None stored. Replaced motor. Tested unit. Unit operating as designed. OFFICE READ NOTES ON RECALLS.
Near Fresno, CA 93727
Timothy
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDF520PADM7 Customer states the units console lit up when it was plugged in and then there was no function after that. Separated door and found the control was not flush against the console. Reset controls position and ran a service test. Unit checks ok. Unit had excess suds possible spill. The unit is not fully installed. The cabinet doesn’t not allow for any adjustment of the unit because the feet have ro be fully raised for the unit to fit in it. Kick plate is difficult to install because of this. Left off.
Near Fresno, CA 93726
Timothy
Job Details: 05/06/2019
DRYER MAYTAG MEDC215EW "Customer states the unit just stopped working. Customer states someone came and checked the outlets and the were ok. Checked power at the service block. I found the following measurements. L1-N=0 vac, L2-N 240 vac, L1-L2 240 vac . Called WPTS who stated the customer should consult an electrician about why the voltage supply changes when under load. Once this is addressed and there is still an issue with the unit to call back for service."
Near Clovis, CA 93611
Timothy
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRS588FIHV00 Customer had a recording of the sound . Identified the sound as the damper. Replaced with pre ID part. Tested with step 3. Unit operating as designed. No leaks noted.
Near Clovis, CA 93611
Timothy
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRS325FDAW04 Installed led assembly. Tested. Unit operating as designed.
Near Upland, CA 91784
Tyler
Job Details: 05/06/2019
WASHER WHIRLPOOL WFW72HEDW0 Customer stated the long drain code and pressure system code came back. Ordering pressure switch hose and air trap not in stock.; ordrng 1 W10903220 (trap) and 1 W11044558 (hose) and 1 WPW10448876 (switch-wl)
Near La Puente, CA 91746
Stephen
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRF535SWHV00 "Replaced right RC door gasket, damper control. Ran diagnostics. Damper is opening/ closing properly. Advised customer to leave RC doors closed at least 4 hours before opening. Unit is cooling properly at this time. Complete."
Near La Verne, CA 91750
Tyler
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW8500DW0 "Customer stated that the unit is not locking, found error code for lock. Lid is broken in the left rear corner at hinge. Ordering lid not in stock.; ordrng 1 W11101421 (lid)"
Near Duarte, CA 91010
Stephen
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDF520PADW7 "Ran diagnostics. Had 7-1 error code. Found wire off heater. ( had to pull DW to reconnect wire- sunk under floor). Reconnected wire to heater. Ran auto test cycle- passed. Fills, washes, drains, rinses, & dries properly. Advised customer to call plumber/ builder- no air gap. Complete."
Near San Gabriel, CA 91776
Stephen
Job Details: 05/06/2019
WASHER AMANA NTW4516FW3 "Ran diagnostics. Had f5e2 error code. Ran auto test cycle. Latch won’t lock. Found latch failed. Replaced latch assembly. Ran auto test cycle, calibration- passed. Fills, agitates, drains, rinses,& spins properly. Complete.; used 1 W11307244 (LATCH) from stock"
Near Covina, CA 91722
Stephen
Job Details: 05/06/2019
REFRIGERATOR KITCHENAID KBBR306ESS Found right frame rail warped caused by piece of wood too thick. Instructed customer to replace with thinner wood piece. Unit is cooling properly at this time. Complete.
Near Rialto, CA 92377
Tyler
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW8500DC Customer stated that the unit will not spin out the clothes. Found error code for fill valve temp sensor. Ordering valve in stock in San Marcos.; ordrng 1 W11165546 (valve)
Near Covina, CA 91723
Stephen
Job Details: 05/06/2019
RANGE- GAS WHIRLPOOL WEG745H0FS "Unable to put into diagnostics. No display. Found main control, display harness plug burnt. EST 721.27. Labor 150.00. Customer will call Whirlpool customer service. Needs W10885069 control and W10598169 display harness. 2 count job. Allow extra time. Complete."
Near West Covina, CA 91790
Stephen
Job Details: 05/06/2019
DRYER - GAS MAYTAG MGDB765FC0 Replaced overlay/ UI assembly. All functions are working properly. Tumbling and heating properly at this time. Ran diagnostics- ok.Complete.
Near Fontana, CA 92336
Rod
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRS325FDAMO4 "5/2/19 8:44: RO there 5/2 THU, 8:19 to 8:41, Lights in refer and ffd compartments not working.Confirmed Revealed shorted freezer light and replaced both fzr and ffd compartment boards to restore as designed operation.; pckd up 1 W10515057 (light board) and 1 WPW10515058 (light)."
Near Grand Terrace, CA 92313
Rod
Job Details: 05/06/2019
WASHER MAYTAG MHW5630HW0 "No water enters machine. FO E2. And F8 E2 Stored in memory. Indicates water valve failure and load detected when activating clean washer.Valves are humming and water was on at wall supply, properly connected.Product was not Used since installed by Lowe’s repsStacked under dryer.CONSUMER WOULD HAVE TO PAY LABOR TO SEPARATE PRODUCTS FOR ACCESSING VALES. DOES NOT WANT REPAIRED AND WIIL CONTACT LOWES FOR REPLACEMENT PRODUCT. VALES ARE SPECIAL ORDER."
Near Yucaipa, CA 92399
Rod
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDT780SAEM1 Seems too hot to the touch.Could not confirm any issues with heat circuits and ran diagnostics to reset control. Therms seem operating as designed.Found float stuck and freed
Near Highland, CA 92346
Rod
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDT730PAHZ0 Won’t drain waterConfirmed Found faulty pump As designed op returned after replacing defective pump
Near Santa Margarita, CA 93453
Tom
Job Details: 05/06/2019
REFRIGERATOR BO AMANA AFI2539ERM00 "Found right door gasket tearing, customer instruct on French Door gasket care and maintenance, order door gasket. Found IM not rotating, entered diagnostics and activated IM Harvest test, jumped contact points, no rotation. Ice level arm also unable to lock into “off” position, order IM.Icemaker - (W10882923)Right Gasket - (W10830055); ordrng 1 W10830055 (gasket-fip) and 1 W10882923 (icemaker)"
Near Highland, CA 92346
Rod
Job Details: 05/06/2019
DRYER WHIRLPOOL WGD8620HC0 "Leaking from under machine when. Thorough disassembly and examination revealed hos connections , valve integrity and supply to nozzle is not compromised.Further found leaking from between door panel.Leaking btwn door glass and seal inside doorResealed and glass at door making tighter mating surface corrected issue.As designed operation returned with no leaks."
Near Fresno, CA 93711
Timothy
Job Details: 05/06/2019
REFRIGERATOR KITCHENAID KRMF706ESS01 Customer states the unit stopped making ice. The ice melted and ran onto the floor from the dispenser. Today they noticed the unit has just started making ice again. I’m fault code is an E2(lost motor position. Ran a harvest cycle and found it passed without fault. Checked FC(22f)and RC temps (47f). The units sealed system is untapped. The unit is not cooling to capacity. Unit needs a dye drier to test.; ordrng 1 WPW10143759 (dryer)
Near Ridgecrest, CA 93555
Rich
Job Details: 05/06/2019
DISHWASHER MAYTAG MDB4949SDZ0 "Replaced/repair the harness wire . Run diagnostic test mode, passed test.operating us designed"
Near Acton, CA 93510
Rich
Job Details: 05/06/2019
WASHER WHIRLPOOL MVWB765FW2 F 3 E 2F 0 E 4F 8 E 3
Near Palmdale, CA 93551
Rich
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW85008C0 Removed obstruction from drain pump.Operating as designed.
Near Palmdale, CA 93550
Rich
Job Details: 05/06/2019
MICROWAVE AMANA AMV2307PFB2 "Replaced door assm fo cracked latch lever. Ran diagnostics, passed. Leak tested door, .01, passed. Operating as designed."
Near Rosemead, CA 91770
Stephen
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRT138FZDW00 "1 year additional warranty. Found ice ball on cap tube into evaporator, no frost pattern , no leaks visible.Sealed system issue. Ordering compressor, evaporator, unit cover,& drier. SEND SEALED SYSTEM TECH ONLY. 4 count job. Allow extra time.; rqstng P&A on 1 482801 (mount-tray) and 1 W10836706 (evaporator) and 1 W10843121 (drier-tube) and 1 W10919804 (duct-air) and 1 W11218693 (COVER- UNIT) and 1 WPW10507886 (compressor)"
Near San Gabriel, CA 91775
Stephen
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRR56X18FW02 "Found evaporator iced up. Ran diagnostics. Heater drawing 3.2 A. Needs control box, thermistor. 2 count job. Allow extra time. Unit MUST be completely defrosted for 2 days with door open before service.; ordrng 1 W11253231 (CONTROL BOX) and 1 WPW10383615 (thermistor)"
Near Los Angeles, CA 91605
Raymond
Job Details: 05/06/2019
WASHER MAYTAG MVWC416FW1 Installed agitator washplate and dispenser. Tested unit. Unit functions as design3d.
Near Rosemead, CA 91770
Stephen
Job Details: 05/06/2019
WASHER WHIRLPOOL WFW72HEDW0 "Not a recall.Ran diagnostics. Had f9e1, f3e2, & f0e1 error codes. Found worn drain pump, needs air trap per service pointer # W10803528, pressure sensor error. 2 count job. Allow extra time.; rqstng P&A on 1 W10903220 (trap)"
Near Los Angeles, CA 91352
Raymond
Job Details: 05/06/2019
DRYER WHIRLPOOL WGT4027HW0 upon arrival cx states unit is damaging clothes. Strings zippers and small shirts getting caught between drum and bulk head. Contacted Kevin 7724768982 and discussed. Unit is functions as designed. Cx needs to put smaller delicate clothing in garment bag.
Near Los Angeles, CA 91040
Raymond
Job Details: 05/06/2019
DRYER MAYTAG MGDB835DW4 "Upon arrival unit not heating. Found cracked igniter. Replaced igniter and tested, unit functions as designed.; used 1 279311 (IGNITOR KIT & BRACKE) from stock"
Near Los Angeles, CA 91342
Raymond
Job Details: 05/06/2019
COOK TOP WHIRLPOOL WCG55US6HS00
Near Santa Clarita, CA 91321
Raymond
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL KUID508ESS "Upon arrival cx states unit is making ice but ice production isn’t how it was before. Tested and found line to recirculating pump loose causing unit to make a half slab of ice. Secured line to pump and tested, unit now making full slab of ice. Unit functions as designed."
Near Santa Clarita, CA 91350
Raymond
Job Details: 05/06/2019
DISHWASHER MAYTAG MDB7749SBB "Upon arrival cx states unit not draining. Tested and found weak drain pump. Quoted cx for repair, cx approved. Replaced drain pump and tested, unit functions as designed."
Near Castaic, CA 91384
Raymond
Job Details: 05/06/2019
WASHER MAYTAG MHW6000XW1 "Upon arrival cx states unit not filling with water. Tested and found multiple fault codes for overflow, long drain, pressure switch. Ran through auto test and found drain pipe backing up causing unit to reverse siphon. This will cause the fault codes. Unit functions as designed cx needs plumber."
Near Santa Clarita, CA 91390
Raymond
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRS588FIHW00 "Upon arrival cx states unit has stuff floating in water when dispensed. Tested and found this is normal agitation of water, no particulates found in water. Informed cx this is completely normal. Unit functions as designed."
Near La Crescenta-Montrose, CA 91214
Raymond
Job Details: 05/06/2019
REFIRGERATOR JENN-AIR JFC2290VEP8 Picked up data loggers. Need to download data and call tech line.
Near Glendale, CA 91202
Raymond
Job Details: 05/06/2019
DRYER MAYTAG MGD6000AW1 Installed drum and dryer repair kit. Tested unit. Unit functions as designed.
Near Los Angeles, CA 91325
Randy
Job Details: 05/06/2019
OVEN WHIRLPOOL WOD51ES4ES01 Removed and replaced element. Unit did not heat. Removed and replaced thermistor tested now working as designed
Near Los Angeles, CA 91356
Randy
Job Details: 05/06/2019
OVEN KITCHENAID KODE500ESS02 Found unit with f2e1 and f1e0. Faulty ui. Removed and replaced now working as designed cx approves job at this time.
Near Los Angeles, CA 91423
Randy
Job Details: 05/06/2019
DISHWASHER JENN-AIR JDB8700AWP Removed and replaced pump. Now working with no noise no leaks cx approves job
Near Lancaster, CA 93534
Patrick
Job Details: 05/06/2019
RANGE WHIRLPOOL WGG745S0FS02 Removed and replaced valve and caps. Tested unit. All ops checked good
Near Lancaster, CA 93534
Patrick
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL WDT710PAHZ1 Removed and replaced stop. All ops checked good
Near Palmdale, CA 93551
Patrick
Job Details: 05/06/2019
REFRIGERATOR WHIRLPOOL WRS322FDAM04 "Removed Nd rpwlced control, harness and thermostat. Tested unit. All ops checked good"
Near Lancaster, CA 93536
Rich
Job Details: 05/06/2019
DISHWASHER WHIRLPOOL KUDP02FRSS2 "Broken links on springs, reroute for part.; ordrng 1 8535568 (link,door balance)"
Near La Crescenta-Montrose, CA 91214
Rich
Job Details: 05/06/2019
OVEN KITCHENAID KSDG950ESS1 "Replaced both Display Board and UI. Still has F2E1 code. No pin chart to test UI in Tech Sheet. Per previous repair, direct short. Suspect MRC2 control. Unable to contact Whirlpool techline....SENT NEW UI JUST IN CASE, NOT LIKELY NEEDED. ; ordrng 4 W10814133 (bezel-knob)s and 1 W10915031 (panl-cntrl) and 1 W11100515 (cntrl-elec)"
Near Tehachapi, CA 93561
Patrick
Job Details: 05/06/2019
DISHWASHER MAYTAG MDBH945AWS Found the unit needing rework kit. Removed and replaced heater from wpl tested unit. All ops checked good w10327037 was part used
Near Santa Clarita, CA 91351
Michael
Job Details: 05/06/2019
DRYER WHIRLPOOL MGD3500FW0 Cx states unit makes a loud noise when in use with a load in it.Tech started unit and heart no unusual sounds upon unit starting. Check lint screen light was illuminated then went off.Verified at dryer vent unit has flow but has build up of lint inside dryer vent. Showed cx issue and advised to get dryer vent serviced. House cleaner states clothing come out slightly damp after cycles. Removed front panel and removed blower housing. Found ball of lint clumped inside blower wheel spinning off bal.Emptied lint obstruction and put unit back together.Loaded a full load of towels and clothing and ran unit for approx 15 minutes while standing with husband and no further sounds. Unit ops as designed.Advised cx to service vent and Cx purchased vent cleaning kit and will service himself. Job complete and Cx is happy with products.
Near Canyon Country, CA 91387
Michael
Job Details: 05/06/2019
WASHER WHIRLPOOL WTW7300DW0 Tipped unit back and removed seized drain pump. No obstructions found inside pimp but impeller is seized. Installed new drain pump WPW10581874Rebooted unit and ran unit calibration successfully.Ran unit through auto service and passed all cycles as designed. Unit ops are now normal job complete.
Near Los Angeles, CA 91331
Michael
Job Details: 05/06/2019
DRYER WHIRLPOOL WGD4815EW2 Dryer rear seal is flapping inside drum.Removed drum. Installed new felt and glued in place. Installed drum and front panel. Drum spins as designed. Advised cx to wait 24 hrs to let adhesive dry. Job complete
Near Los Angeles, CA 91344
Michael
Job Details: 05/06/2019
DRYER MAYTAG MGDC215EW1 "Cx is a land lord, tenant states long dry times. Tech started unit and no unusual noises. Prompt ignition. Tech went outside to inspect vent and found 10% airflow at best. Showed cx issue and advised he clean his dryer vent. Cx will clean vent himself. Unit ops as designed job complete"
Near Perris, CA 92571
Kevin
Job Details: 05/06/2019
WASHER MAYTAG MVWB765FW1 OEM failure. Customer stated they were getting off balance codes when unit was level. I tested unit and heard a knocking sound from under unit. I tipped unit back and found rotor was slightly loose causing knocking sound and can also give false off balance codes. I tightened rotor and inspected slider. Tested unit. All tests good.