Near Bakersfield, CA 93306
Patrick
Job Details:
02/19/2021
OVEN MAYTAG MEW9630FZ03
7729902248 only getting half power. Needs electrician
Near South El Monte, CA 91733
Stephen
Job Details:
02/19/2021
DISHWASHER KITCHENAID KDTE254ESS2
"Replaced drain motor. Cleaned filters. Fills, washes, drains, rinses, and dries properly at this time. Air gap backing up. Instructed customer to call plumber, use affresh DW cleaner. Complete."
Near Rosemead, CA 91770
Stephen
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRF535SWHZ04
"Ran diagnostics. Found FC drain iced up, overflowing. Deiced FC drain, floor. FC drain is draining properly at this time. Instructed customer not to put open packages in FC. Unit is cooling properly at this time. Complete."
Near Los Angeles, CA 90049
Isidore
Job Details:
02/19/2021
WASHER MAYTAG MHW8200FW0
"Found no codes and detergent set to 6x concentration, set to 3x.Customer states no detergent coming out and detergent drawer handle not staying on.Reinstalled detergent handle, and test detergent pump.Found detergent pump working at this time."
Near Los Angeles, CA 90049
Isidore
Job Details:
02/19/2021
DRYER ELECTRIC WHIRLPOOL WED97HEXR0
"Removed top and front panel, drum, old roller and belt.Installed new dryer repair kit 4392067( 4 rollers, 1 idler pulley and belt).Reinstalled panels and test dryer operation, dryer working at this time as designed."
Near Topanga, CA 90290
Isidore
Job Details:
02/19/2021
RANGE AMANA AGR5330BAS3
"Needs to have range conversion NG to LP W11379310 kit if needed, explained to customer conversion is not covered by warranty . Customer to call propane service to do conversion. Thinks warranty covers this"
Near Los Angeles, CA 90042
John
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRT112CZJZ00
"whirlpool technician. SR7730027924. The drain trough was iced over below the evaporator in the freezer. Defrosted all the ice, secured the defrost heater into the drain hole properly. The refrigerator tested good at this time."
Near Los Angeles, CA 90041
John
Job Details:
02/19/2021
REFRIGERATOR KITCHENAID KRFF507HPS00
"The light in the freezer section has failed, and the light module inside the refrigerator has failed. Replace the light inside the refrigerator section ceiling, And the freezer section. Tested good at this time."
Near Fresno, CA 93711
Irvin
Job Details:
02/19/2021
WASHER AMANA NTW4516FW
"Removed power from unit. Installed components. Assembled unit. Calibrated unit, passed. All ops normal."
Near Fresno, CA 93710
Irvin
Job Details:
02/19/2021
WASHER MAYTAG MVW7230HW0
"Removed power replaced HMI, and MAIN CONTROL. powered washer. Followed procedures for calibration, passed. Unit started cycle, all ops normal."
Near Los Angeles, CA 91436
Danny
Job Details:
02/19/2021
DISHWASHER WHIRLPOOL KDTE334GPS0
Unit is washing the dishes Found faulty motor assy Replaced motor sump assy Reinstall and power up and ran a self test cycle and unit completed with no leaks and no issues Unit is working properly
Near Westlake Village, CA 91361
Danny
Job Details:
02/19/2021
MICROWAVE KITCHENAID KMBS104ESS02
Unit is not heating Pulled unit out and place microwave in top of floor protection Replaced magnetron and diode and microswitchesReinstall and power up No floor or cabinet damage Test unit and unit is heating and cycling properly ; used 2 W10269457 (Micro switches) from stock
Near Los Angeles, CA 91042
Leon
Job Details:
02/19/2021
WASHER MAYTAG MVWB835DC4
Replaced all selected parts After running diagnostic check unit working properly as designed
Near Baldwin Park, CA 91706
Andy
Job Details:
02/19/2021
WASHER WHIRLPOOL WTW5005KW0
"Not filling, found loose wire to water valve,repaired connection and tested unit working properly, found no error codes after test"
Near Duarte, CA 91010
Andy
Job Details:
02/19/2021
DRYER WHIRLPOOL WGD5100HW0
"Not drying good and makes noise, found blower wheel Stripped causing noise and causing the dryer not to drive fast enough. Replaced blower wheel and tested unit working properly"
Near Azusa, CA 91702
Andy
Job Details:
02/19/2021
DISHWASHER WHIRLPOOL KDTE104ESS0
"Customer saidt was not heating, ran test and checked heater was working no error codes tested unit working properly at this time"
Near Glendora, CA 91741
Andy
Job Details:
02/19/2021
WASHER WHIRLPOOL WTW4955HW1
"Not filling, found water valve not working, removed hoses and tested lines had water reinstalled hoses and tested unit working properly at this time"
Near Pomona, CA 91768
Andy
Job Details:
02/19/2021
WASHER MAYTAG MVWC565FW2
"Shifter not working, replaced shifter and tested unit working properly"
Near Walnut, CA 91789
Andy
Job Details:
02/19/2021
WASHER WHIRLPOOL WTW5000DW0
"Customers said was unit was making a knocking stripping noise. Ran unit in test mode found no error codes checked wash plate was not stripped, looked at lower part of gear case no signs of noise or where tested unit working good no noise at this time"
Near Mariposa, CA 95338
Kenneth
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRX735SDHZ03
Customer was concerned with ice getting jammed in container. Informed customer that once done dispensing crushed ice to switch it to cubed to dispense out all the built up crushed ice. Custoner noticing ice inside her meat bags. Informed customer that unit is trying to pull moisture out of the bags. And it has no where to go so it freezes inside bags. Door alarm normal. Informed customer I was unable to increase the sound volume. Unit is working properly. Adjusted temperatures to allow the pantry drawer to be slightly cooler for customer.
Near Madera, CA 93638
Marshall
Job Details:
02/19/2021
DRYER WHIRLPOOL WED6620HC1
Installed UI and main control board test run complete everything working properly job complete.
Near Madera, CA 93637
Marshall
Job Details:
02/19/2021
WASHER MAYTAG MVWB835DW4
Installed main board UI and lid lock test run complete everything working properly job complete.
Near Madera, CA 93637
Marshall
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRF767SDEM01
Installed freezer led light test run complete everything working properly job complete.
Near Madera, CA 93637
Marshall
Job Details:
02/19/2021
DRYER ROPER RED4640YQ
Installed thermal fuse from truck stock test run complete everything working properly job complete.; used 1 WP3392519 (Thermal fuse) from stock
Near Visalia, CA 93291
Chase
Job Details:
02/19/2021
DRYER MAYTAG MGDC215EW2
Cx saiding unit still making thumping sound. Ran through cycle. Found felt unaligned. Realigned felt. Sound is now eliminated. Job complete.
Near Bakersfield, CA 93314
Chase
Job Details:
02/19/2021
DRYER MAYTAG MEDB855DC4
Per DTB not charging for part. Installed dryer kit. All functions now testing normal. Complete.
Near Bakersfield, CA 93311
Chase
Job Details:
02/19/2021
OVEN WHIRLPOOL WOS51EC0HS01
Control keeps loosing time and will not chime. This is an ongoing issue cx has been dealing with. Installed new ui board. Programmed and all functions are now testing out normal. Please bill for double labor for removing built in oven.
Near Montebello, CA 90640
Juan
Job Details:
02/19/2021
WASHER WHIRLPOOL WFW5620HW0
"Replaced main control board. Ran diagnostics, all units ops check fine."
Near Bakersfield, CA 93311
Chase
Job Details:
02/19/2021
WASHER GE GTW845CPN0DG
Cx said that smart dispense is not working. Found connector to control came loose not allowing control to detect input from smart dispense. Reconnected and retested. All functions now testing out normal. Job complete.
Near Bakersfield, CA 93313
Chase
Job Details:
02/19/2021
WASHER WHIRLPOOL WFW5620HW0
Cx saidt that unit is leaking coming from the front. Ran through test cycle found unit is leaking coming from out of the front. Found bellow not properly adjusted allowing for leak to come out from bellow. Removed bellow and re applied. Unit no longer leaking. All functions now testing out normal. Job complete.
Near Bakersfield, CA 93309
Chase
Job Details:
02/19/2021
DRYER WHIRLPOOL WED4950HW0
"Cx saidt that unit will not heat properly. Tested unit, and found that dryer is in fact heating up properly how it should be. This is a venting issue. Instructed cx to clean out vents. All functions are testing out normal with this machine. Job complete."
Near Bakersfield, CA 93309
Chase
Job Details:
02/19/2021
DISHWASHER KITCHEN AID KDTE334GPS0
"Cx not happy with performance of machine. 5-1, switch error. Found loose connector to latch. All functions now testing out normal. Instructed cx on Lemi shine product to help clean out inside. Unit working by design. Job complete."
Near Bakersfield, CA 93309
Chase
Job Details:
02/19/2021
DRYER WHIRLPOOL WED4850HW0
Found stuck push to start button. Reset button. All functions now testing out normal. Job complete.
Near Bakersfield, CA 93309
Chase
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRS571CIHZ01
Adjusted dispenser housing. Unit no longer leaking. All functions now testing normal. Job complete.
Near Ceres, CA 95307
Cruz
Job Details:
02/19/2021
ELECTRIC RANGE WHIRLPOOL WFE505W0JS0
"Fixed- installed new parts (3 coils) tested all element burners and found them to be working as designed, the appliance is at RAC in Ceres"
Near Winton, CA 95388
Cruz
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRS325SDHZ05
"Fixed- installed new part (diffuser) found cooling and temps to be working fine, diffuser is opening/closing as designed, cx ok repair"
Near Squaw Valley, CA 93675
Timothy
Job Details:
02/19/2021
WASHER WHIRLPOOL WGT4027HW0
Found both valves have the same resistance. Both valves operate in service mode. Called WPTS(7730027021) and explained what I was seeing. In the deep fill cycles the unit would use only hot water when selected but in normal cycles there would be a mixture of hot and cold. This is normal operation.
Near Fowler, CA 93625
Timothy
Job Details:
02/19/2021
WASHER MAYTAG MVWB765FW3
Installed lid. Tested unit. Unit checks ok.
Near Reedley, CA 93654
Timothy
Job Details:
02/19/2021
WASHER MAYTAG MHW5630HC
"Inspected unit and found a small leak at the gasket. Gasket was twisted, reset gasket."
Near Dinuba, CA 93618
Timothy
Job Details:
02/19/2021
REFRIGERATOR JENN-AIR JS48CSDBDA
Customer states the unit was dripping from the evaporator area and was not cooling as effectively as normal. Checked drain pan and found it looked ok. The heaters and thermostat had continuity. Noted the ice door was not sealed. This could be the source of the dripping and cooling issues. The IM does not work and the ice door never needs to open or close. Closed the ice door manually and told the customer to monitor the unit and call if needed.
Near Caruthers, CA 93609
Timothy
Job Details:
02/19/2021
WASHER MAYTAG MVWC565FW1
Installed control. Calibrated unit. Ran a service test. Unit operating as designed.
Near Porterville, CA 93257
J.E.
Job Details:
02/19/2021
WASHER GE GTW335ASN0WW
Installed new lid lock and re-tested unit get it filled and started washing with no issues. Job completed
Near Porterville, CA 93257
J.E.
Job Details:
02/19/2021
RANGE WHIRLPOOL WFG320M0BS3
Cycled unit and found control board not responding to any commands and display flashing and dim. Installed new control board and retested unit passed all test at time of service. Job completed
Near Visalia, CA 93292
J.E.
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRV986FDEM01
Installed new parts and re-tested unit unit passed all test at time of service. Job completed
Near Clovis, CA 93619
Matthew
Job Details:
02/19/2021
WASHER WHIRLPOOL WTW5000DW3
Checked washer for not working found control wire harness not completely connected repaired connection all tests passed.
Near Clovis, CA 93619
Matthew
Job Details:
02/19/2021
OVEN WHIRLPOOL WOS51EC0HS01
Installed new control panel and tested all passed.
Near Clovis, CA 93619
Matthew
Job Details:
02/19/2021
DRYER MAYTAG MGD6630HC1
Installed new belt and tested operation all tests passed.
Near Fresno, CA 93730
Matthew
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRF767SDHZ02
Installed new Im and water valve all tests passed.
Near Fresno, CA 93730
Matthew
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRT311FZDW01
Installed new ice maker and cycled all tests passed.
Near Fresno, CA 93720
Matthew
Job Details:
02/19/2021
WASHER KENMORE 11044832200
Found front tub boot not installed properly another company replaced the boot. Reinstalled boot all tests passed.
Near Clovis, CA 93619
Matthew
Job Details:
02/19/2021
REFRIGERATOR KITCHENAID KRFC704FPS04
Installed l side fresh food door sent to customer all tests passed.
Near Delano, CA 93215
Erick
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRT138FZDW00
Installed new parts on unit. Re-tested unit and unit passed all test with no faults at the time of service.
Near Shafter, CA 93263
Erick
Job Details:
02/19/2021
WASHER MAYTAG MVWB865GW
Install new parts on unit. Re-tested unit and unit is now filling with no faults. Job complete
Near Bakersfield, CA 93314
Erick
Job Details:
02/19/2021
FREEZER GENERAL ELECTRIC FUF21DLRCWW
Installed new parts on unit. Re tested unit and board stop chiming .Set temperatures to correct settings. Unit passed all tests. Job complete
Near Bell Canyon, CA 91307
Danny
Job Details:
02/19/2021
FREEZER KITCHENAID KBSD618ESS
No lights Found faulty led modules Replaced modules and reinstall and power up All lights are working properly Advised client to allow 24hrs for unit to reach proper temp
Near Los Angeles, CA 91304
Danny
Job Details:
02/19/2021
OVEN WHIRLPOOL KODC304EBL
Unit is not heating properly Found faulty sensors Replaced sensor and main control Test unit and ovens are now heating and cycling properly No floor or cabinet damage Unit is now working properly
Near Taft, CA 93268
Mitch
Job Details:
02/19/2021
WASHER MAYTAG MVWB835DW4
Upon arrival customer stated unit is making noise and unit is leaking water found unit to be making noise caused by coins stuck in between impeller and basket causing unit to make noise. I removed impeller to remove coins. removed coins and reinstalled impeller tested unit is no longer making noise. Tested in cycle unit is not leaking found customer to have water coming from behind wall informed customer to call a plumber the unit is functioning properly and not leaking at this time of service.
Near Taft, CA 93268
Mitch
Job Details:
02/19/2021
RANGE WHIRLPOOL WFG525S0JZ0
Upon arrival I removed and replaced control tested unit is functioning properly at this time of service.
Near Bakersfield, CA 93307
Mitch
Job Details:
02/19/2021
DRYER MAYTAG MGDC465HW0
Upon arrival customer stated unit is making noise tested u it found unit to be making noise caused by bad rollers unit needs new dryer repair kit removed and replaced rollers and pull-ups tested unit is functioning properly at this time of service.
Near Bakersfield, CA 93306
Mitch
Job Details:
02/19/2021
OVEN WHIRLPOOL WOS51EC0HS01
Upon arrival I removed and replaced console tested unit is now heating and is functioning properly at this time of service.
Near Port Hueneme, CA 93041
Isidro
Job Details:
02/19/2021
WASHER MAYTAG MVW6230HW0
"On arrival I ran diagnostics found error codes F7E7, motor unable to reach target RPM, F0E2 over suds, I advised customer to not use much soap she was using over a cup, found shifter off, reinstalled shifter, calibrated unit,tested unit, unit is now spinning and operating properly as designed at this time of service...job complete"
Near Camarillo, CA 93010
Isidro
Job Details:
02/19/2021
WASHER WHIRLPOOL WFW6620HC2
"On arrival I replaced , installed and secured the outer door, tested unit, unit is now as designed...job complete"
Near Camarillo, CA 93012
Isidro
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRX735SDHV01
"On arrival I found unit getting stuck with ice in the chute, installed plastic square, tested unit, unit is now dispensing water and ice properly as designed...job complete"
Near San Luis Obispo, CA 93405
Brandon
Job Details:
02/19/2021
DRYER GENERAL ELECTRIC GUD24GSSM1WW
Changed out igniter and thermostats. Reassembled and re-tested unit. Unit is now igniting and heating as intended at time of service. Job complete
Near Porterville, CA 93257
J.E.
Job Details:
02/19/2021
FREEZER WHIRLPOOL WRF767SDHZ00
Cycled unit and found Freezer light receiving voltage but not operating. Also check UI and Spencer all checked OK. Installed new light module and re-tested unit all operations test normal at time of service. Job completed
Near Porterville, CA 93257
J.E.
Job Details:
02/19/2021
DISHWASHER WHIRLPOOL WDF330PAHS3
Cycled unit and found gasket slipping off. Try to reinstall the gasket seems loose. Installed new gasket and re-tested unit unit now working as designed. Job complete
Near San Bernardino, CA 92405
Rod
Job Details:
02/19/2021
DRYER MAYTAG MGDB765FW0
Door catch adjustment off. Confirmed adjusted door catch as designed operation returned
Near San Bernardino, CA 92407
Rod
Job Details:
02/19/2021
WASHER MAYTAG MVWB765FW4
Machine wont operate. Confirmed from stored fault code that a stuck button was experienced.After assessing issue found code was temporary. Recalibrated and as designed op returned with noo recurring faults.
Near Paso Robles, CA 93446
Jack
Job Details:
02/19/2021
RANGE HOOD GENERAL ELECTRIC CV936EK1DS
Customer received the filters. Installed and ready to go. Job completed.
Near Cambria, CA 93428
Jack
Job Details:
02/19/2021
ELECTRIC RANGE ELECTROLUX EI30EW48TSA
Switch was installed. Unit is now working. Fans are running witch the never worked. Unit is preheating. So unit hit the 350 mark and it works. Lower oven works also. Job completed.
Near Cambria, CA 93428
Jack
Job Details:
02/19/2021
DISHWASHER KITCHEN AID KDTM404EBL0
Unit starts goes to wash cycle and no water. Pump motor assembly was bad. Needed to be released
Near Morro Bay, CA 93442
Jack
Job Details:
02/19/2021
DRYER GENERAL ELECTRIC GTD42GASJ2WW
Unit still not heating. Replaced 3 thermostats and unit is up and heating. Tested and went through unit one more time. Checked vent also. Job completed
Near Acton, CA 93510
Jonathan
Job Details:
02/19/2021
RANGE GE JTD5000SN1SS
120 black to white. Red to black 60w red to white 5w. Not correct power to unit
Near Hesperia, CA 92344
Cesar
Job Details:
02/19/2021
WASHER WHIRLPOOL WTW6120HC0
Belt came off reinstalled tested good
Near Santa Maria, CA 93455
George
Job Details:
02/19/2021
WASHER WHIRLPOOL WTW5000DW3
Installed part testing ok complete no dents or dings cause by tech.
Near Orcutt, CA 93455
George
Job Details:
02/19/2021
RANGE JENN-AIR JGRP436WP01
Installed part tested check out ok complete no dents or dings cause by tech.
Near Los Angeles, CA 91343
Joe
Job Details:
02/19/2021
DISHWASHER WHIRLPOOL KDTE334GBS0
Console was cracked and would not allow you to turn on delay start options. Replaced console and unit began to function as designed. Job complete
Near Modesto, CA 95355
Cruz
Job Details:
02/19/2021
WASHER AMANA NTW4516FW3
"Fixed- installed new part (water pump) tested the appliance in diagnostic test mode it completed filled, wash, drain, spin, no codes, no leaks, the appliance is working fine at this time, cx ok repair."
Near Modesto, CA 95355
Cruz
Job Details:
02/19/2021
DRYER MAYTAG MEDC215EW
"Fixed for fcc- found drum to be out of position causing dumping sounds, removed front panel and reposition drum reassemble front panel and tested the appliance in a high heat cycle it heated fine, no thumping sound, cx ok repair send cx a survey please thanks."
Near Colton, CA 92324
Rod
Job Details:
02/19/2021
REFRIGERATOR MAYTAG MFX2876DRE00
"Door alarm inop and cooling in freezer insufficient Confirmed inop door alarm with as designed cooling in freshfood compartment. Deli monitor in op due to spillage into it. Deli monitor is no longer avail even for this product. Certain features will not be functional as a result, ie: icemaker and some other low voltage functions.
Near Hanford, CA 93230
Andrew
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL KRSC703HPS00
Found unit not cooling. Checked all joints and found no leaks. Did find leak at the valve stem on dryer. Removed and replaced valve stem. Pulled vacuum on unit and unit held vacuum. Recharged unit with 5.75 ounces of 134A. Unit is cooling fine
Near Porterville, CA 93257
J.E.
Job Details:
02/19/2021
WASHER MAYTAG MVW6230HW0
Cycled unit and found unit not shifting. Checked shifter shifter receiving voltage but not responding. Replaced shifter and re-tested unit unit passed all test at time of service. Job completed
Near Riverside, CA 92509
Kevin
Job Details:
02/19/2021
WASHER MAYTAG MVWB865GW0
Unit not filling to correct water level. I tested unit and found it under filling on the water level. I put unit into diagnostic and recalibrated the water level. Retested unit. Water levels are now filling to proper levels.
Near Riverside, CA 92503
Kevin
Job Details:
02/19/2021
REFRIGERATOR KITCHENAID KRFC704FBS00
Sealed system under warranty through manufacture. Removed and replaced evaporator and compressor. Vacuumed system down. Charged with 4.65 oz of Freon. Tested unit. All tests good.
Near Riverside, CA 92507
Kevin
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRS325SDHW05
Removed and replaced ice maker. Tested unit. All tests good.
Near Burbank, CA 91505
Leon
Job Details:
02/19/2021
WASHER MAYTAG MVWX655DW1
Replaced motor driveAfter running diagnostic check unit working properly as designed Dispatch to collect from the Cx remaining balance
Near Adelanto, CA 92301
Darren
Job Details:
02/19/2021
WASHER ROPER RTW4640YQ1
"Replaced faulty drain pump, recalibrated washer, cycle tested unit, checked out okay."
Near Ridgecrest, CA 93555
Patrick
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL WRF560SEHZ00
Removed and replaced defrost thermistor. Heater checked good. Tested unit. All ops checked good
Near Ridgecrest, CA 93555
Patrick
Job Details:
02/19/2021
WASHER MAYTAG MVWC465HW2
Removed and replaced belt. Tested unit. All ops checked good
Near Porterville, CA 93257
J.E.
Job Details:
02/19/2021
WASHER MAYTAG MVWX655DW1
"Cycled unit F0E2, F9E1 error codes indicating over suds also f8e1 long drain. Checked control board and found control board is faulty also found drain pump is weak and no working properly. Installed new pump and control retested uni and unit passed all tests at time of service. Job completed."
Near Camarillo, CA 93012
Isidro
Job Details:
02/19/2021
DRYER WHIRLPOOL WGD4950HW0
"On arrival I removed broken igniter, installed and secured new igniter, tested unit, unit tested okay and operating properly as designed...job complete"
Near Topanga, CA 90290
Isidore
Job Details:
02/19/2021
RANGE WHIRLPOOL WFE320M0ES0
"Removed range to access rear range control panel and removed old front right infinity switch. Installed new right front infinity, reinstalled panels.Test range operation, range is working at this time as designed."
Near Perris, CA 92571
Kevin
Job Details:
02/19/2021
WASHER WHIRLPOOL WFW7590FW0
Removed and replaced main control and pressure switch hose. Tested unit. All tests good.
Near Moreno Valley, CA 92551
Kevin
Job Details:
02/19/2021
REFRIGERATOR WHIRLPOOL KRMF706EBS01
Removed and replaced control boards and ice maker. Tested unit. All tests good.
Near Moreno Valley, CA 92555
Kevin
Job Details:
02/19/2021
DRYER WHIRLPOOL WGD5000DW3
Unit making noise. I removed lint duct and found blower wheel rubbing on lint duct. I adjusted motor to allow blower wheel to sit straight. Tested unit. All tests good.
Near Moreno Valley, CA 92557
Kevin
Job Details:
02/19/2021
WASHER MAYTAG MVWX655DW2
Removed and replaced drain pump and main control at the same time. Tested unit. All tests good.
Near Bakersfield, CA 93314
Erick
Job Details:
02/19/2021
ICE MACHINE KITCHEN AID KUIX535HPS00
Cycled and found rear upper circulating coming off causing it to fail and not make ice. Removed and properly secured tubing. Retested it and unit is now cycling with no faults. Job complete
Near Yucaipa, CA 92399
Rod
Job Details:
02/19/2021
WASHER MAYTAG MVW6200KW0
Returned to replace defective part and as designed op returned consumer had parts shipped direct to home. 1x W11406492 and 1x W11481108
Near Los Angeles, CA 91401
Danny
Job Details:
02/19/2021
REFRIGERATOR MAYTAG MSS26C6MFZ00
Unit is not making ice Found faulty ice maker Replaced and install new ice maker Ran a test and ice maker cycles and filled up with water Collected payment by card
Near Thousand Oaks, CA 91320
Isidro
Job Details:
02/19/2021
DRYER MAYTAG MGD7230HW0
"On arrival customer stated unit was not working or drying properly, installed new burner coils, tested unit, unit is igniting for over 50 sec at a time , unit is now operating properly as designed...job complete"