Service History 770 - Appliance Repair Specialists

We serviced a

MAYTAG WASHER

Model MVW6200KW1

Near El Monte, CA 91733

Juan

Job Details: 10/29/2021

"Upon arrival error code F2e3 was displayed. Cleared error code. Electrical outlet needs to be repaired, when checking with the meter, it checks fine, but when the power cord is connected, no voltage comes through to the unit. Connected unit to a different outlet. Ran diagnostics, all units operations checked fine. Found a few coins stuck between the wash plate and spin basket, pointed them out to the customer, and advised to check all the pockets. The unit is working properly.

We serviced a

MAYTAG WASHER

Model MVWB835DC4

Near El Monte, CA 91733

Juan

Job Details: 10/29/2021

"Upon arrival error code F8e6. F0e3. F2e1 were displayed. Cleared error codes, reset main control board, calibrated machine. Ran diagnostics, all operations working as designed. Ran a normal cycle, the unit is working as designed. Advised customer to continue to use the unit, to run the clean washer cycle with AFFRESH at least once a month."

We serviced a

AMANA WASHER

Model NTW4516FW1

Near Rosemead, CA 91770

Juan

Job Details: 10/29/2021

"Unit was in cancellation mode, drain pump running continuously. Cancelled cycle, calibrated machine, no error codes stored, ran diagnostics, all operations working as designed. Unit filled, agitated, drained, and spun as designed."

We serviced a

MAYTAG WASHER

Model MVWX655DW2

Near Montebello, CA 90640

Juan

Job Details: 10/29/2021

"Replaced actuator and splutch assembly. Calibrated machine, ran diagnostics. All operations working as designed. The unit is working as designed."

We serviced a

JENN-AIR REFRIGERATOR

Model JFFCC72EHL01

Near Modesto, CA 95355

Cruz

Job Details: 10/29/2021

Upon arrival installed new part (ice maker) . Ice maker cycled and water filled. Cooling and temps are working fine as well on unit. Customer is satisfied with repair.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ03

Near Modesto, CA 95355

Cruz

Job Details: 10/29/2021

Upon arrival installed new door. Door is now opening and closing as designed. Gasket is sealing to cabinet. Sutomer satisfied with repair.

We serviced a

MAYTAG WASHER

Model MVWC465HW3

Near Modesto, CA 95355

Cruz

Job Details: 10/29/2021

Upon arrival error code f5e7 appeared which is an actuator fault code. Top loader washer not agitating due to faulty actuator. Removed bad one and installed new one (actuator). Calibration test pass as well as auto test pass. The appliance is now agitating as designed. Customer satusfied with repair.

We serviced a

AMANA WASHER

Model MVWC565FW2

Near Fresno, CA 93702

Irvin

Job Details: 10/29/2021

No errors found in the system. Customer says the washer is not agitating or spinning. Confirmed issue. Found a bad shifter. Installed replacement shifter. Calibration passed. All operations working as designed.

We serviced a

WHIRLPOOL DISHWASHER

Model WDTA50SAKZ0

Near Cambria, CA 93428

Jack

Job Details: 10/29/2021

Unit is not draining. Ran cycle. F9e1. Found the air gap was clogged. Cleaned out and drains really good. Running another cycle. Doing 3 more add one. Stove and microwave and fridge. Customer needed help with these. Job completed

We serviced a

FRIGIDAIRE DISHWASHER

Model FFID2426TD5A

Near Arroyo Grande, CA 93420

Brandon

Job Details: 10/29/2021

The left side of the cabinet had a slight warp. I used a him and heat gun to correct it and fix the leak. Complete

We serviced a

BOSCH DISHWASHER

Model SHPM65W55N

Near Tollhouse, CA 93667

Marshall

Job Details: 10/29/2021

Installed drain pump test run complete everything working properly job completed.

We serviced a

MAYTAG WASHER

Model MVWX655DW2

Near Orange Cove, CA 93646

Timothy

Job Details: 10/28/2021

Replaced suspension and tested. Unit checks ok.

We serviced a

WHIRLPOOL WASHER

Model WTW7000DW4

Near Fresno, CA 93711

Irvin

Job Details: 10/28/2021

"Removed washer power. Replaced gearcase clutch, and slider. After assembly. Ran calibration cycle passed. Unit operates properly."

We serviced a

MAYTAG DRYER

Model MGDX655DW2

Near Glendora, CA 91741

Andy

Job Details: 10/28/2021

"Unit makes noise, found rollers bad, replaced roller kit tested unit working as designed."

We serviced a

WHIRLPOOL WASHER

Model WFW6620HW2

Near Glendora, CA 91741

Andy

Job Details: 10/28/2021

"Upon arrival found drain house needed to be repaired. Repaired drain hose and tested unit. Unit working good at this time. No error codes"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706EBS01

Near Glendora, CA 91741

Andy

Job Details: 10/28/2021

"Not cooling, replaced compressor and evaporator tested unit working as designed"

We serviced a

FRIGIDAIRE ELECTRIC RANGE

Model FGEH3047VF0

Near Fresno, CA 93710

Irvin

Job Details: 10/28/2021

"Customer states that the units oven control is not operating properly. Customer states that the unit displays random information on the screen. After removing power, replaced control board. Installed unit into place. Tested for operation. Unit passed and operates as designed."

We serviced a

AMANA REFRIGERATOR

Model ART318FFDS07

Near Fresno, CA 93704

Irvin

Job Details: 10/28/2021

Gasket came out of channel. Installed adhesive and installed gasket. All operations normal. ; used 1 8201711 (Adhesive) from stock

We serviced a

MAYTAG WASHER/COMMERCIA

Model MVWP575GW0

Near Fresno, CA 93703

Irvin

Job Details: 10/28/2021

"Removed power from washer. Removed gearcase from unit. Replaced component. Assembled unit after installing gearcase. Ran calibration cycle passed. Spin agitate and drain ,all pass."

We serviced a

FRIGIDAIRE DISHWASHER

Model FGID2466QF

Near Fresno, CA 93727

Irvin

Job Details: 10/28/2021

The unit is operating. Replaced strike. Test failed. The inner door had too much material causing the door and strike to mid align. Removed the intrusive plastic. Unit is operating properly. All operations good.

We serviced a

CROSLEY REFRIGERATOR

Model XRS16BGAWP

Near Fresno, CA 93706

Irvin

Job Details: 10/28/2021

"Unit not cooling. The fan motor is not operating. Removed frezer rear panel. Checked power to the motor. Getting 120v. Replaced motor, powered unit.,fan is on unit is cooling. Compressor is running. All operations normal."

We serviced a

MAYTAG DRYER

Model MGD6230HW0

Near Palmdale, CA 93552

Jonathan

Job Details: 10/28/2021

"Found defective sensor, fixed sensor. Tested unit and is working properly"

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Santa Maria, CA 93454

George

Job Details: 10/28/2021

Installed parts tested check out ok complete no dents or dings cause by tech.

We serviced a

WHIRLPOOL WASHER

Model MVWB765FC3

Near Manteca, CA 95337

William

Job Details: 10/28/2021

"Replaced rotor & slider, ran self diagnostics, unit operating as designed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB322DMBM03

Near Fresno, CA 93726

Marshall

Job Details: 10/28/2021

Found unit had a bad icemaker installed one from truck stock test run complete everything working properly job completed.; used 1 W11556926 (Icemaker) from stock

We serviced a

WHIRLPOOL DRYER

Model MGDB835DW4

Near San Bernardino, CA 92407

Rod

Job Details: 10/28/2021

"Returned, replaced defective parts and as designed operation was restored. 1 279640 idler"

We serviced a

MAYTAG WASHER

Model MVWC465HW2

Near Oxnard, CA 93036

Isidro

Job Details: 10/28/2021

"On arrival I found a broken drain pump, I replaced and secured new drain pump, tested unit, unit is now draining and operating properly as designed , Concession auto MZKY600APL1"

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ0

Near Oxnard, CA 93035

Isidro

Job Details: 10/28/2021

"On arrival I found error codes f8e4, I replaced and installed new float switch erased error code, tested unit, unit is now operating properly as designed"

We serviced a

KITCHENAID DISHWASHER

Model KDTM354DSS5

Near Oxnard, CA 93035

Isidro

Job Details: 10/28/2021

"On arrival I found the unit with the control lock on , I unlocked unit , tested unit, unit is operating properly as designed at this time of service"

We serviced a

GENERAL ELECTRIC DRYER

Model GTD84GCSN1WS

Near Oxnard, CA 93035

Isidro

Job Details: 10/28/2021

"I found the unit not heating, broken igniter at delivery, I installed and secured new igniter, tested unit, unit is now heating and operating properly as designed"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ04

Near Lancaster, CA 93536

Jonathan

Job Details: 10/28/2021

"Replaced broken ice bucket and found temps of fridge at 33f, put temps back to recommend temps.. tested unit and is working properly"

We serviced a

GENERAL ELECTRIC DISHWASHER

Model PDT715SYNFS

Near Oxnard, CA 93035

Isidro

Job Details: 10/28/2021

"I found a disconnected heating element at the harness , I reinstalled and secured wire harness to the element, tested unit, unit is now heating and operating properly as designed at this time of service , also customer instruct"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KRMF706EBS01

Near Oxnard, CA 93035

Isidro

Job Details: 10/28/2021

"On arrival I removed ice maker assembly, cleared out ice buildup in the ice maker are by the ice fan near the the back wall, thawed out gaskets, reinstalled and secured,unit is leak free at this time of service"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAHZ0

Near Los Angeles, CA 90049

Isidore

Job Details: 10/28/2021

"Removed outer door panel, old detergent dispenser and installed new detergent dispenser. Reinstalled door pane and test for leaks and operation.Dishwasher working at this time as designed."

Near Los Angeles, CA 91344

Leon

Job Details: 10/28/2021

undefined

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW2

Near Rancho Cucamonga, CA 91730

Jaime

Job Details: 10/28/2021

Installed control and water valve washer ok

We serviced a

KITCHENAID DISHWASHER

Model KDFM404KPS0

Near Atascadero, CA 93422

Jack

Job Details: 10/28/2021

"Unit is not responsive at all. Will go into diagnostics but thats it. No control. 91 code. Found drain was clogged and no were to drain to, needs a new air gap. Customer knows. Dishwasher works and drains correctly now. Job completed"

We serviced a

JENN-AIR RANGE

Model JGRP436WP01

Near Atascadero, CA 93422

Jack

Job Details: 10/28/2021

Upon arrival found control board defective. Replaced Control. Unit tested good. Working as designed. Customer will keep tabs on whats goin on with their unit. Job completed.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF507HPS01

Near Rancho Cucamonga, CA 91701

Jaime

Job Details: 10/28/2021

Installed freezers light module

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SNHM06

Near Upland, CA 91784

Jaime

Job Details: 10/28/2021

Made adjustments on the low and high side lines. Tighten condenser motors housing

We serviced a

WHIRLPOOL WASHER

Model MVWB766FW1

Near Templeton, CA 93465

Jack

Job Details: 10/28/2021

Replacing parts listed. Ran a diagnostics test and calibration test with new main board and ui board. Unit passed and all checked out. Job completed

We serviced a

WHIRLPOOL RANGE

Model DGRSC366

Near Lompoc, CA 93436

George

Job Details: 10/28/2021

We dont service dynasty brand .

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT518SZFW00

Near Lompoc, CA 93436

Alejandro

Job Details: 10/28/2021

"Found the unit, not cooling, verify leak in evaporator, replace evaporator, service valve and drier-uv, charge refrigerant 4.3 oz R134a check compressor condenser and refrigerator fan motors running normal ; used 1 W10913906 ( Service valve), and 1 WPW10143759 ( Drier -uv) from stock"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FGHF2366PFBA

Near Grover Beach, CA 93433

Brandon

Job Details: 10/28/2021

Installed new kit according to instructions. Unit is operating as designed now. Complete

We serviced a

WHIRLPOOL FREEZER

Model ASI2575GRS

Near Los Angeles, CA 91306

Randy

Job Details: 10/28/2021

Found ice build up at freeer. Under fill tube. Removed ice. Fill tube was misaligned. Fixed and aligned. Now working no more leaks. Job complete.

We serviced a

THERMADOR RANGE HOOD

Model HDDB36WS

Near Los Angeles, CA 91423

Randy

Job Details: 10/28/2021

Removed and replaced ui. Tested now working as designed

We serviced a

WHIRLPOOL WASHER

Model WFW5620HW0

Near Los Angeles, CA 91423

Randy

Job Details: 10/28/2021

Found unit not working properly. Obstruction in pump. Removed and now working great. Job complete

We serviced a

WHIRLPOOL DRYER

Model WGD4950HW0

Near Moreno Valley, CA 92557

Kevin

Job Details: 10/28/2021

Removed and replaced inner door and door seal. Tested unit. All tests good.

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Moreno Valley, CA 92557

Kevin

Job Details: 10/28/2021

Lid broken and not starting cycle. I removed and replaced lid and strike. Tested and calibrated. All tests good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHV04

Near Moreno Valley, CA 92555

Kevin

Job Details: 10/28/2021

Removed and replaced pads and interface. Tested unit. All tests good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ03

Near Moreno Valley, CA 92555

Kevin

Job Details: 10/28/2021

Removed and replaced ice maker. Tested ice maker. All tests good.

We serviced a

KITCHENAID DISHWASHER

Model KDTE334GPS0

Near Marcel, CA 93561

Cruz

Job Details: 10/28/2021

"Customer said that the appliance is working fine at this time- I was able to ran a diagnostic test it completed fill, wash, drain, heated, no error codes, no leaks, customer satisfied with repair."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ02

Near Moreno Valley, CA 92553

Kevin

Job Details: 10/28/2021

Removed and replaced ice maker. Tested unit. All tests good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model KFCS22EVMS0

Near La Cañada Flintridge, CA 91011

Leon

Job Details: 10/28/2021

Replaced door mullion Unit working properly as designed

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ11

Near Burbank, CA 91505

Leon

Job Details: 10/28/2021

Replaced main board. Unit working as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRV986FDEM00

Near Los Angeles, CA 91352

Leon

Job Details: 10/28/2021

Customer states that unit is still not producing ice. After running diagnostic check. I found that IM wire connector in freezer section was disconnected. Reconnect IM connector. Unit working as designed.

We serviced a

JENN-AIR COMPACTOR

Model TC607X4

Near Los Angeles, CA 91411

Randy

Job Details: 10/28/2021

Found kept making noise. Found loose pedal. Not hitting button. Removed foot pedal and adjusted. Tested now working great. Job complete.

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW2

Near Los Angeles, CA 91401

Randy

Job Details: 10/28/2021

Customer stated that the unit shakes n vibrates. Checked unit and foudn that it was unbalanced. Banalanced. Advised customer on use and load. All operations normal job complete.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHW08

Near Modesto, CA 95356

Cruz

Job Details: 10/28/2021

Fixed- installed new part (ice maker) ice maker cycled and water filled- cooling and temps are working fine as well

We serviced a

ELECTROLUX WASHER

Model EFLS627UIW2

Near Modesto, CA 95358

Cruz

Job Details: 10/28/2021

"Found clamp to pump not tighten hard enough causing water to leak out during filling- tighten clamp ran diagnostic test it completed filled, wash, drain, spin, no leaks, customer satisfied with repair."

We serviced a

MAYTAG WASHER

Model MVWC465HW2

Near Modesto, CA 95358

Cruz

Job Details: 10/28/2021

Upon arrival found customer stated that the appliance is not working properly and soap is not dissolving. Found that customer was not using proper water level setting and was overloading. Checked for any error codes found none. Informed customer to use bulky/ sheet cycles from water and how to load wash basket. Ran a calibration test and the unit passed. Unit auto test passed as well. Found the appliance to be working as designed. Customer satisfied with repair.

We serviced a

WHIRLPOOL REFRIGERATOR

Model KRMF706ESS04

Near Fontana, CA 92336

Tyler

Job Details: 10/28/2021

Customer stated that the unit is not making ice. Found error code for ice maker thermistor. Removed and replaced ice maker tested all works good at this time.

We serviced a

WHIRLPOOL MICROWAVE

Model WOC54EC0HS04

Near Fontana, CA 92336

Tyler

Job Details: 10/28/2021

Customer stated that the clock adjusts too fast. Removed and replaced console tested all works good at this time.

We serviced a

MAYTAG WASHER

Model MVW6230HW0

Near Fontana, CA 92336

Tyler

Job Details: 10/28/2021

Customer stated that the unit is making noise in the spin. Found gear case is leaking oil. Removed and replaced gear case belt and cam tested all works good at this time.

We serviced a

WHIRLPOOL DISHWASHER

Model KDTE334GPS0

Near Covina, CA 91724

Jaime

Job Details: 10/28/2021

Found no leak at all at the time of service. 125.00 charge

We serviced a

FRIGIDAIRE RANGE

Model LFGH3054UF

Near California City, CA 93505

Patrick

Job Details: 10/28/2021

Found the units oven not switched to propane conversion. Adjusted the regulator and tested unit. All operations checked out.

We serviced a

MAYTAG REFRIGERATOR

Model MFI2670XEM0

Near Ridgecrest, CA 93555

Patrick

Job Details: 10/28/2021

Filter not in all the way. Installed filter and tested 7nit. All operations checked good. Charged service call

We serviced a

GENERAL ELECTRIC WASH/DRY COMBO

Model GUD27GSSM2WW

Near Ridgecrest, CA 93555

Patrick

Job Details: 10/28/2021

Removed and replaced burner valve. Tested unit. All operations checked out.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEHZ

Near Ridgecrest, CA 93555

Patrick

Job Details: 10/28/2021

Customer having issues with the ice maker. Bail arm uninstalled causing no operation. Reinstalled and secured. Tested unit. All operations checked out

We serviced a

MAYTAG WASHER

Model MVWC565FW0

Near Searles Valley, CA 93562

Patrick

Job Details: 10/28/2021

Removed and replaced motor. Calibrated and ran automatic test. All operations checked good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHZ04

Near Pasadena, CA 91107

Francisco

Job Details: 10/28/2021

Customer stated door wouldnt close on its own when swinging it closed. Informed customer I could raise front legs to get the door to swing back. Adjusted legs unit now closes. Customer also wanted doors flush I used heat gun to get them as even as possible but they are fully closing. Appliance operating as designed.

We serviced a

WHIRLPOOL DRYER

Model WGD5620HW

Near Sierra Madre, CA 91024

Francisco

Job Details: 10/28/2021

"Retested everything found coils failing under load after 20 mins run time. Removed and replaced coils and unit now checks ok.; used 1 279834 (Gas coils) from stock"

We serviced a

WHIRLPOOL WASHER

Model CAE2745FQ1

Near Pasadena, CA 91103

Francisco

Job Details: 10/28/2021

"Removed and replaced tub ring,adapter,and shifter. Leveled unit. Calibrated and tested operations. Unit now working as designed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Monterey Park, CA 91754

Francisco

Job Details: 10/28/2021

Found high side pressure tubing making contact with card board base causing vibration. Adjusted tubing and pushed refrigerator back in and tested. No abnormal noise. Leveled door to the best of my ability due to uneven ground leveing. Customer approved leveling. Unit now working as designed.

We serviced a

WHIRLPOOL WASHER

Model MVWC565FW2

Near Malibu, CA 90265

Isidore

Job Details: 10/28/2021

"Found actuator not seated in cam, top load washer well not agitate. Removed old actuator and installed new actuator W10913953.Test washer operation, washer working at this time as designed ; used 1 W10913953 (Actuator) from stock"

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW3

Near Malibu, CA 90265

Isidore

Job Details: 10/28/2021

"Found F3E2 water inlet temperature fault, removed top control panel, old water valve and installed new water valve assembly. Reinstalled top panel and test for leaks and operation, washer working at this time as designed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Rosemead, CA 91770

Juan

Job Details: 10/28/2021

"Customer reports the unit was not producing ice at one point. Checked ice bin on arrival, the bin was full. Ran icemaker harvest test, it went through it and filled as designed. Advised customer to monitor the ice production. All units operations check fine at the time of service."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT112CZJW00

Near West Hollywood, CA 90046

John

Job Details: 10/28/2021

The freezer section was full of ice. The drain was plugged with ice. Removed all the ice and unplugged the drain. I did not find any debris in the drain system. Tested good at this time.

We serviced a

WHIRLPOOL RANGE

Model WFG320M0BW2

Near Colton, CA 92324

Rod

Job Details: 10/28/2021

Outer glass shattered VerifiedReplaced defective glass panel and as designed condition was restored.

We serviced a

WHIRLPOOL WASHER

Model WTW8127LW0

Near Phelan, CA 92371

Cesar

Job Details: 10/28/2021

We serviced a

AMANA DRYER

Model NGD4655EW3

Near Riverside, CA 92504

Kevin

Job Details: 10/28/2021

"Unit making noise during operation. I found failed rollers and belt. Removed and replaced rollers and be,t with repair kit. All tests good."

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Riverside, CA 92504

Kevin

Job Details: 10/28/2021

Unit not draining. Removed and replaced drain pump that whirlpool had sent to customer. Tested unit. All tests good.

We serviced a

KITCHENAID REFRIGERATOR

Model KRSC703HPS01

Near Manteca, CA 95336

William

Job Details: 10/28/2021

"Ran ice maker test 44 , ice maker failed to w find home, Replace ice maker, ran ice maker test, unit operating as designed.; used 1 W10873791 (Ice maker) from stock"

We serviced a

MAYTAG DRYER

Model MED5630HC1

Near Manteca, CA 95336

William

Job Details: 10/28/2021

"Replaced motor , blower housing & blower wheel , ran test dryer cycle, unit sounds & operating as designed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Los Banos, CA 93635

Nick D

Job Details: 10/28/2021

"Freezing over everything. Replaced with new unit, new unit working as designed"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAHZ0

Near Los Angeles, CA 91307

Devon W.

Job Details: 10/28/2021

Instructed customer when raising the top rack the rack must lock into place before trying to load or it wont line up and the door wont close. I Showed customer where there issue was and unit is now functioning as designed. Job complete.

We serviced a

KITCHENAID REFRIGERATOR

Model KSSC42QMS03

Near Calabasas, CA 91302

Devon W.

Job Details: 10/28/2021

Installed coupler and shaft unit function as designed job complete Did not collect payment

We serviced a

WHIRLPOOL DRYER

Model WET4024HW

Near Los Angeles, CA 91367

Devon W.

Job Details: 10/28/2021

Instructed customer that unit fails to reach its full heat ability when on air dry. I put the unit on very dry and it gets heat. Upon further inspection the exhaust hose had water in it due to a blockage toward the roof. Notified customer that they would have to get the vents cleaned.

We serviced a

WHIRLPOOL ICE MACHINE

Model WRS555SIHZ

Near Visalia, CA 93291

J.E.

Job Details: 10/28/2021

Cycled unit and found in an out producing in the ice. Checked icemaker and found icemaker Has failed Installed new icemaker and re-tested unit Ill just pass the time of service. Job completed; used 1 W10873791 (Ice maker) from stock

We serviced a

MAYTAG WASHER

Model MVWB865GW0

Near Livingston, CA 95334

Kenneth

Job Details: 10/28/2021

Installed valve and tested unit. Unit is working properly. Customer approves function at this time.

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Visalia, CA 93291

J.E.

Job Details: 10/28/2021

Installed new washbay re-tested unit all test pass the time of service. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW2

Near Visalia, CA 93292

J.E.

Job Details: 10/28/2021

Cycled unit and found long fill error code checked valve and found filters clogged with what looks to be sand. Cleaned filters and retested unit passed all test at time of service. Instructed to checked filters frequently because home water supply is Well water. Will charge service fee if we have to come back out for same reason

We serviced a

WHIRLPOOL WASHER

Model MVW6200KW

Near Exeter, CA 93221

J.E.

Job Details: 10/28/2021

Cycled unit and found worn belt causing noise as for the smell customer House washer drain into sink located in laundry room that causing the smell. Installed new belt and re-tested unit unit passed all test of time of service. Job completed; used 1 W11239857 (Belt) from stock

We serviced a

WHIRLPOOL FREEZER

Model WRF757SDHZ00

Near Tracy, CA 95376

William

Job Details: 10/28/2021

"Unit already serviced by other service provider, Cx canceled job at door."

We serviced a

MAYTAG M/W OTR

Model MMV1175JZ00

Near Tracy, CA 95376

William

Job Details: 10/28/2021

"Found blower motor installed in the wrong Configurations with duct mounting screws locking blower wheel, remounted blower motor in unit, replaced screws with shorter screws, reinstalled in cabinet, tested blower motor functions, unit operating as designed"

We serviced a

GE DRYER

Model GTD42GASJWW

Near Lindsay, CA 93247

J.E.

Job Details: 10/28/2021

Cycled unit and found broken belt. Installed new belt and re-tested unit all test pass at time of service. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW

Near Strathmore, CA 93267

J.E.

Job Details: 10/28/2021

Installed new agitator and re-tested unit all test pass a time of service. Job completed

We serviced a

KITCHENAID FREEZER

Model KRFF507HWH00

Near Turlock, CA 95380

Kenneth

Job Details: 10/28/2021

Ibstalled icemaker. Tested unit. Unit is now working properly. Customer approves function at this time.

We serviced a

JENN-AIR REFRIGERATOR

Model JFFCC72EFP02

Near Turlock, CA 95382

Kenneth

Job Details: 10/28/2021

Ibstalled cover and control. Tested. Unit is working properly. Customer approves function at this time.

We serviced a

GENERAL ELECTRIC REFRIGERATOR

Model GNE27JYMNFFS

Near Winton, CA 95388

Kenneth

Job Details: 10/28/2021

Handle popping off easily. Replaced mount brackets and tightened down really well. Secured handle. Tested. Unit is working propelty.