We serviced a
WHIRLPOOL OVEN
Model WFG320M0MS0
Near Littlerock, CA 93543
Jonathan B.
Job Details: 11/02/2023
JB out 11/2/23.Installed replacement oven igniterW11590294. Tested oven-ok.Reassembled unit and tested oven in Bake mode set to 350f.Unit now operates as designed.No charge to.JOB COMPLETE.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Los Banos, CA 93635
Jonathan
Job Details: 11/02/2023
Found thermal fuse open replaced tested working properly ; used 1 WP3390719 (THERMAL FUSE) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Firebaugh, CA 93622
Jonathan
Job Details: 11/02/2023
Found heater open quoted customer approved repair unit needs to be defrosted before it will work properly installed heater tested working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS586FLDW00
Near Los Banos, CA 93635
Jonathan
Job Details: 11/02/2023
Installed control and heater tested working properly
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Oxnard, CA 93030
Kenneth
Job Details: 11/02/2023
Installed gearcase and belt. Tested unit. Unit is working properly. Customer approves function at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Oxnard, CA 93033
Kenneth
Job Details: 11/02/2023
Found unit with defrost issues. Replaced wire harness and tested. Unit is working properly. Ensured unit is on 8 hour defrost.
We serviced a
AMANA REFRIGERATOR
Model ASI2175GRS08
Near Oxnard, CA 93033
Kenneth
Job Details: 11/02/2023
Installed thermistor and tested unit. Unit is working properly. Customer approves function at this time.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Camarillo, CA 93010
Kenneth
Job Details: 11/02/2023
Found unit with the foam blanket coming out of the side. Uninstalled dishwasher and taped blanket to the tub and pushed it in to ensure the foam did not pop out. Unit is working properly. Customer approves function at this time. Ensured blanket would not catch the hinges while door was opening and closing.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Moreno Valley, CA 92557
Kevin
Job Details: 11/02/2023
"Removed and replaced cover, fan motor, and pan kit. All tests good."
We serviced a
MAYTAG MICROWAVE
Model MVWP575GW1
Near Glendale, CA 91207
Leon
Job Details: 11/02/2023
Customer states that unit is not working properly After running diagnostic check get error code F2E1 Replaced main board Unit working properly as required
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Riverbank, CA 95367
Martin R
Job Details: 11/02/2023
Found cam locked up causing actuator to go bad Replaced cam and actuator tested unit washer is filling agitating draining and spinning properly Job complete ; used 1 W10913953 (Actuator) from stock
We serviced a
MAYTAG DRYER
Model MED5630HC2
Near Ripon, CA 95366
Martin R
Job Details: 11/02/2023
Found bad thermal fuse replaced fuse tested unit dryer is heating and tumbling properly job com
We serviced a
WHIRLPOOL RANGE
Model WFE320M0JS3
Near Oakdale, CA 95361
Martin R
Job Details: 11/02/2023
Replaced bad control tested unit surface burners are working and bake and broiler also working Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Atwater, CA 95301
Nathaniel C
Job Details: 11/02/2023
"Installed new motor damper, all functions tested okay. New motor damper opening and closing as designed. Call complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Winton, CA 95388
Nathaniel C
Job Details: 11/02/2023
Installed new capacitor and found grease on clutch. System. Tested unit with full load of clothes. Tested okay. Techline said possible control issue or wiring harness issue if recall. Sr#7737702514
We serviced a
KITCHENAID RANGE
Model KSGB900ESS4
Near Simi Valley, CA 93063
Paul M
Job Details: 11/02/2023
"Front burners were not igniting. Replaced all orfices on unit. After repair all burners worked as designed, check oven to see if temp was low, everything seems normal but calibrated unit 10 degrees above to help out with temp. Customer brought up that oven wasnt heating up as it was before. Job complete"
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ2
Near Los Angeles, CA 91325
Paul M
Job Details: 11/02/2023
"Plugged in unit, all buttons works. Drained unit and works as designed. Ran diagnostics mode and went through all stages as designed. Unit is now working as designed, job complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Simi Valley, CA 93063
Paul M
Job Details: 11/02/2023
"IM was broken, tray was out of place. Replaced broken IM and unit is now working as designed. Job complete"
We serviced a
KITCHENAID REFRIGERATOR
Model KBFN506EBS01
Near San Luis Obispo, CA 93405
Paul V
Job Details: 11/02/2023
Remove existing LED lights. Installed new LED lights. Unit operating as designed.
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model ZISS480DNGSS
Near Nipomo, CA 93444
Paul V
Job Details: 11/02/2023
Control/temp/icemaker/fan change out. Removed existing parts listed. Install new parts listed. Test ran unit. Unit operating as designed.
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT650SYV0FS
Near Morro Bay, CA 93442
Paul V
Job Details: 11/02/2023
Remove existing control/sensors/water valve. Installed new parts listed. Test ran unit. Unit operating as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHW04
Near Santa Clarita, CA 91350
Randy
Job Details: 11/02/2023
Found unit making loud vibration noise from cabinet. Warm to touch. Removed back cover and found loose connection at condenser fan. Plugged in all the way and now running as designed. Customer to wait 24 hours for proper temps. All ops working as designed.
We serviced a
FRIGIDAIRE RANGE
Model FGGH3047VFD
Near Santa Clarita, CA 91350
Randy
Job Details: 11/02/2023
F005 Unit panel randomly throws code Tested. Threw code. Removed and replaced control panel. Tested now working as designed. Job complete.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Bakersfield, CA 93307
Raymond
Job Details: 11/02/2023
"On arrival grinding noise when slowing down, found worn Splutch assembly. Replaced and tested, unit functions as designed.; used 1 W10721967 (Splutch) from stock"
We serviced a
FRIGIDAIRE RANGE
Model LFGH3054UFC
Near Arvin, CA 93203
Raymond
Job Details: 11/02/2023
"Installed spark harness, tested, unit functions as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFF507HPS04
Near Tehachapi, CA 93561
Raymond
Job Details: 11/02/2023
Installed door. Rectified cosmetic concerns.
We serviced a
WHIRLPOOL DRYER
Model WGD7500GC0
Near Thousand Oaks, CA 91362
Richard R
Job Details: 11/02/2023
"Upon arrival, replaced inner door of dryer, tested unit unit is working as intended. The gasket on the old inner door was torn."
We serviced a
WHIRLPOOL RANGE
Model AGR6303MMS0
Near Riverside, CA 92507
Robert U.
Job Details: 11/02/2023
Found the switchs checked ok so I replaced the spark module and that restored the operation of the cooktop. All other functions tested properly as well. Job completed
We serviced a
MAYTAG DRYER
Model MGDC465HW0
Near Riverside, CA 92507
Robert U.
Job Details: 11/02/2023
After replacing all parts ordered the drum is now rotating properly. All functions are working properly now. Job completed.
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model PVD28BYNFS
Near Riverside, CA 92509
Robert U.
Job Details: 11/02/2023
After installing the new slides and adjusting the cams the freezer door now closes properly. I verified all other operations in diagnostics and all tested ok. No f codes stored. Job completed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model KBSD602ESS00
Near Riverside, CA 92506
Robert U.
Job Details: 11/02/2023
After replacing the door the door is no longer leaking. All functions tested ok. Job completed.
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW0
Near Loma Linda, CA 92354
Robert U.
Job Details: 11/02/2023
After installing new pump I ran a diagnostic cycle and no more leaks found. All other functions are working properly. I checked for codes again and none stored. All test ok. Job completed.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Riverside, CA 92504
Ruben O
Job Details: 11/02/2023
File 7737703545.Tested unit in diagnostic cycle many times unit working fine every time. No error found in the memory of unit. Previously replaced drain pump. Unit is operating as designed per techline. Call complete
We serviced a
WHIRLPOOL WASHER
Model WGTLV27HW2
Near Riverside, CA 92503
Ruben O
Job Details: 11/02/2023
Replaced broken actuator and found the pressure hose disconnected from board. Installed pressure and tested after repair all ok.; used 1 W10913953 (Actuator) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Riverside, CA 92505
Ruben O
Job Details: 11/02/2023
Replaced faulty actuator and cam in order to fix loud grinding noise issue.
We serviced a
WHIRLPOOL DRYER
Model WGD85HEFC0
Near Los Angeles, CA 91326
Sean W
Job Details: 11/02/2023
Replaced dryer repair kit.dryer working properly.
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW2
Near Los Angeles, CA 91325
Sean W
Job Details: 11/02/2023
Replaced thermal fuse and motor.dryer working properly.
We serviced a
WHIRLPOOL REFRIGERATOR/TOP
Model WRT518SZFW02
Near McFarland, CA 93250
Shane g
Job Details: 11/02/2023
Old unit was over freezing. Removed old unit and installed new unit and new unit is operating as designed. Job complete
We serviced a
MAYTAG DRYER
Model MGD5630HW0
Near Monrovia, CA 91016
Stephen
Job Details: 11/02/2023
"Unit is stacked in small room. Replaced support rollers, idler pulley, and belt. Cleaned shafts, base and motor. Replaced console/ ACU kit per service pointer W11395626A. Found loose connector on HMI. Corrected connector. Replaced door hinge. Tumbling and heating properly at this time. Instructed customer to call duct cleaning service."
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near East Los Angeles, CA 90022
Stephen
Job Details: 11/02/2023
"Had to break agitator Replaced gear case, splutch, shifter, capacitor, belt, and agitator. Locks/ unlocks, fills,,drains, rinses, and spins properly at this time. Instructed customer NOT to use powdered detergent. Complete."
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model HPS16BTNJRWW
Near Dinuba, CA 93618
Timothy
Job Details: 11/02/2023
Installed evaporator fan and defrosted ducting. Unit checks ok.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FPRU19F8WF1
Near Salida, CA 95368
Timothy G
Job Details: 11/02/2023
Replaced compressor and checked for leaks. No leaks present. Charged with 48 grams r600. Unit seems to be cooling per design. Job complete
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GYE22GYNJFS
Near Ontario, CA 91762
Tyler
Job Details: 11/02/2023
Customer stated that unit is still not cooling in freezer. Called tech line file number 11367827. Found leak on cap tube. Removed and replaced compressor and charged with R600. Tested all works good at this time.
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Fresno, CA 93706
Irvin
Job Details: 11/01/2023
"Over load, and stuck keyF2/E1, F0/E3CHECKED VALVE, allowing water into the unit. The washer in normal mode is washing and no water in the unit. The hot valve is buzzing with little or no water to the unit. Replaced the valve. Ran and pass DLMS cycle, unit fills correctly. Set the unit up for clean washer, unit filling properly. All ops normal. DONE."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Fresno, CA 93706
Irvin
Job Details: 11/01/2023
"Replaced gearcase, latch strike, main control and other components. Completed assembly. Powered unit, ran calibration Cycle. All ops normal. DONE."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Madera, CA 93638
Irvin
Job Details: 11/01/2023
"The unit is not showing any errors. There is ice build up. Cleared ice replaced the dampner. Removed rear panel in freezer, released all ice. Assembled unit, all ops normal. DONE."
We serviced a
SPEEDQUEEN WASHER
Model AWN632SP116TW02
Near Ventura, CA 93003
Isidro
Job Details: 11/01/2023
"Bad inlet water valve not opening, not get enough water coming in, Installed new water valve unit is now getting water and operating properly as designed, customer approved repairs"
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GZS22IYNXHFS
Near Oxnard, CA 93036
Isidro
Job Details: 11/01/2023
"Installed new ice maker and main control board, 18;hours to regulate, unit should operate as designed at this time of service"
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Ventura, CA 93003
Isidro
Job Details: 11/01/2023
"Broken adjusters feet, I installed new adjusters, and tracks , unit is now operating properly as designed, customer approved repairs"
We serviced a
MAYTAG WASHER
Model MVWP575GW0
Near Covina, CA 91722
Jaime
Job Details: 11/01/2023
Found a bad hub. Had it replace. Washer ok; used 1 W10528947 (Hub) from stock
We serviced a
WHIRLPOOL DRYER
Model MGDB850WQ1
Near La Verne, CA 91750
Jaime
Job Details: 11/01/2023
"No heat at all, no ignitor ignitor and thermostas too. Replaced a heat kit along with coils."
We serviced a
WHIRLPOOL WASHER
Model WTW8000DW5
Near La Verne, CA 91750
Jaime
Job Details: 11/01/2023
Installed the new latch assembly washing machine works OK
We serviced a
KENMORE WASHER
Model 110.20702991
Near Covina, CA 91724
Jaime
Job Details: 11/01/2023
Installed the new transmission drain pump coupler clutch and Basket Dr Drive. Washer OK
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Bakersfield, CA 93314
James
Job Details: 11/01/2023
Defrosted evaporator and replaced harness.Tested ok
We serviced a
GENERAL ELECTRIC WASH/DRY COMBO
Model GFW850SPN3RS
Near Bakersfield, CA 93309
James
Job Details: 11/01/2023
Replaced defective drain pump and door lock. Also removed obstruction from drain hose. Updater firmware.Tested ok
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW2
Near Delano, CA 93215
James
Job Details: 11/01/2023
"Installed new wire harness, calibrated and tested. Unit now working as intend3d."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Delano, CA 93215
James
Job Details: 11/01/2023
Installed new components as instructed by techline. Calibrated and tested. Unit working as intended.
We serviced a
WHIRLPOOL WASHER
Model MHW8630HC4
Near Bakersfield, CA 93304
James
Job Details: 11/01/2023
Installed new components and tested unit. Unit working as intended.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Springville, CA 93265
J.E.
Job Details: 11/01/2023
Cycled unit and found bad capacitor causing unit to fail installed new capacitor and retested unit now working as designed job completed. Capacitor and labor covered by whirlpool. Scode S17538; used 1 W11162560 (Capacitor) from stock
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS09
Near Visalia, CA 93292
J.E.
Job Details: 11/01/2023
Installed new parts and retested unit now working as designed job completed
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Tulare, CA 93274
J.E.
Job Details: 11/01/2023
Cycled unit and found bad motor. Installed new motor retested unit now working as designed job completed
We serviced a
WHIRLPOOL REFRIGERATOR
Model KBFN502ESS01
Near Exeter, CA 93221
J.E.
Job Details: 11/01/2023
Installed new lights and retested unit lights now working as designed job completed
We serviced a
AMANA RANGE
Model AGR6303MMS0
Near Strathmore, CA 93267
J.E.
Job Details: 11/01/2023
Installed new parts and retested unit now working as designed job completed
We serviced a
JENN-AIR REFRIGERATOR
Model JS48NXFXDE01
Near Los Angeles, CA 90272
Jim
Job Details: 11/01/2023
"Replaced board, thermistor, and deli board"
We serviced a
MAYTAG WASHER
Model MHW8630HW0
Near Los Angeles, CA 90077
Jim
Job Details: 11/01/2023
Complaint is unit not draining properly. The spin cycle was turned off
We serviced a
WHIRLPOOL DRYER
Model WGD6620HW0
Near Beverly Hills, CA 90210
Jim
Job Details: 11/01/2023
Replaced thermal fuse and flame sensor. Unit tested OK.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Beverly Hills, CA 90210
Jim
Job Details: 11/01/2023
Replaced outer tub. Unit tested ok
We serviced a
AMANA DRYER
Model NGD4655EW4
Near Lancaster, CA 93536
Jonathan
Job Details: 11/01/2023
Found unit with insufficient airflow remove blockage tested unit is working properly
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC2
Near Palmdale, CA 93552
Jonathan
Job Details: 11/01/2023
"Found defective fabric softener dispenser, fixed dispenser, tested unit and is working properly"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT665SSN8SS
Near Lancaster, CA 93536
Jonathan
Job Details: 11/01/2023
Found unit working properly. No error codes at this time. Client is not using rinse aid. Customer education on use and care of unit
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Palmdale, CA 93552
Jonathan B.
Job Details: 11/01/2023
"JB Out 11/123Customer states lid will no longer lock so washer does not wash. Upon arrival found lid strike broken. Replaced lid. Strike part number W11457841 from truckstock. Tested operation with customer. Washer now operates as designed. Recommend customer use HE only detergent and very, very small amounts typically maximum of one Measured Teaspoon. No charge to customer. Job complete ; used 1 W11457841 ( STRIKE) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Mendota, CA 93640
Jonathan
Job Details: 11/01/2023
Found drian pump shorted replaced tested working properly
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Firebaugh, CA 93622
Jonathan
Job Details: 11/01/2023
Installed hub and agitator tested working properly
We serviced a
GENERAL ELECTRIC DISHWASHER
Model CDT845P2N5S1
Near Dos Palos, CA 93620
Jonathan
Job Details: 11/01/2023
Found connection at door switch reinstalled tested working properly no leaks
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Firebaugh, CA 93622
Jonathan
Job Details: 11/01/2023
"Found actuator and cap bad replaced tested working properly ; used 1 W11158830 (Cap), and 1 W10913953 (ACTUATOR) from stock"
We serviced a
WHIRLPOOL COOKTOP
Model WCC31430AB03
Near Camarillo, CA 93010
Kenneth
Job Details: 11/01/2023
Found unit working as designed. Informed customer of the Thermo protected elements. Informed customer try and insure the pots or pans are not bigger the the silver drip tray. Tested elements and found them cycling on and off as designed.
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT665SSN8SS
Near Fillmore, CA 93015
Kenneth
Job Details: 11/01/2023
Installed rollers and carrier. Tested unit. Unit is working properly.
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDF630PMM3ES
Near Fillmore, CA 93015
Kenneth
Job Details: 11/01/2023
Installed control board and tested. Found unit leaking due to over filling. Not draining. Found drain pump was unplugged. Not alllowing unit to drain. Plugged in drain pump and tested. Unit is working properly. Customer approves function at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Nuevo, CA 92567
Kevin
Job Details: 11/01/2023
Removed and replaced ice maker. All tests good.
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW1
Near Moreno Valley, CA 92555
Kevin
Job Details: 11/01/2023
Customer stated that the unit is turning off before clothes are dry and running too long. I removed and replaced sensor harness and gas coils. Tested unit. All tests good.
We serviced a
KITCHENAID DISHWASHER
Model KDPE334GPS0
Near Los Angeles, CA 91607
Leon
Job Details: 11/01/2023
Customer states that unit is not washing properly Replaced sump motor Unit working properly as required
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Burbank, CA 91505
Leon
Job Details: 11/01/2023
Customer states that unit is not working properly After running diagnostic test find that unit has a bad sump motor Replaced all selected parts Unit working properly as required
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEYM01
Near Atwater, CA 95301
Nathaniel C
Job Details: 11/01/2023
All functions tested okay. Unit working as designed upon arrival. Informed customer to leave gap open on the back inside fridge for better cooling. Sr#7737696259
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Atwater, CA 95301
Nathaniel C
Job Details: 11/01/2023
"All functions tested okay found customer floor to have slope, with is causing the washer to be off. Unit has no issues."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Merced, CA 95348
Nathaniel C
Job Details: 11/01/2023
"Found ice maker not operating properly. Installed new icemaker, all functions tested properly. Informed customer to wait 72 hours to have full bin of ice. Call complete"
We serviced a
MAYTAG DRYER
Model MED6630MBK0
Near Atwater, CA 95301
Nathaniel C
Job Details: 11/01/2023
installed new dryer repair kit and wheel blower. All functions tested OK after part install unit working as designed. call complete; used 1 Wp697772 (Wheel blower) from stock
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Burbank, CA 91505
Oscar L
Job Details: 11/01/2023
A new drawer seal has been replaced and the light switch was defrosted and it worked fine.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Simi Valley, CA 93063
Paul M
Job Details: 11/01/2023
"Unit is not producing ice, replaced ice maker and was given a defective IM. Came back with a new one today and part looked fine. Troubleshoot IM and water came in as designed. Ran is again and nothing was stuck. Unit should now be able to produce ice without issues."
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Los Angeles, CA 91325
Paul M
Job Details: 11/01/2023
"Unit was not draining, connection to the drain pump was cut. Replaced wire harness, unit is now working as designed. Job complete."
We serviced a
KITCHENAID RANGE
Model KFGD500ESS04
Near Pismo Beach, CA 93449
Paul V
Job Details: 11/01/2023
Remove existing igniter. Installed new igniter. Test ran unit. Unit operating as designed
We serviced a
WHIRLPOOL WASHER
Model Wtw7120hw0
Near Santa Clarita, CA 91351
Randy
Job Details: 11/01/2023
Not registering latch. Removed and replaced lid latch. W11394572Tested now working as designed. ; used 1 W11394572 (Latch) from stock
We serviced a
KITCHENAID MICROWAVE
Model KOCE500ESS22
Near Santa Clarita, CA 91354
Randy
Job Details: 11/01/2023
Removed and replaced parts. Tested now working as designed
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Santa Clarita, CA 91351
Randy
Job Details: 11/01/2023
Found led lights not working. Removed and replaced led module from truck stock. Now lights working as designed ; used 1 W11484836 (Module) from stock
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Santa Clarita, CA 91390
Randy
Job Details: 11/01/2023
Unit has leak from heater. Found unit falls under Technical Service Pointer #: W11540964Removed and replaced heater. Installed and tested. No more leaks. Ran diagnostics passed. Customer approved. Customer has floor damaged. Referred to manufacture. Definitely caused by heater. Unit passed all tested now working as designed.
We serviced a
MAYTAG DRYER
Model MGD6230HW0
Near Santa Clarita, CA 91350
Randy
Job Details: 11/01/2023
Removed and replaced cam and belt. Tested now working as designed Removed and replaced dryer repair kit on dryer. Tested now working as designed.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KBS02
Near Bakersfield, CA 93308
Raymond
Job Details: 11/01/2023
"Installed fan motor, tested, unit functions as designed."
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Bakersfield, CA 93308
Raymond
Job Details: 11/01/2023
"Installed control, tested unit functions as designed."
We serviced a
UNKNOWN RANGE
Model JGBS15GER3WH
Near Bakersfield, CA 93308
Raymond
Job Details: 11/01/2023
"Installed ignitor and thermostat, tested, unit functions as designed."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near San Bernardino, CA 92404
Robert U.
Job Details: 11/01/2023
Found no error codes stored at this time. Found the fabric softener dispenser full and not dispensing. I removed the console and found a loose connection at the fabric softener valve. After reconnecting all functions were restored. All functions are now working properly. Job completed
We serviced a
MAYTAG WASHER
Model MVWB765FW0
Near San Bernardino, CA 92404
Robert U.
Job Details: 11/01/2023
Found two issues one the unit had a f2e1 error code. I removed the error and ran a user interface test and all functions tested ok in that test. I then ran a diagnostic cycle and noticed the motor not operating properly. I tilted the unit back and found the bolt that holds the rotor in place dropped down so the motor was not secured. I removed the motor and checked the clutch and slider and all tested ok. I reinstalled the bolt and ran a diagnostic cycle and finished with a recalibration cycle on step 52 in diagnostics. All functions were restored job completed.