Found unit unplugged and evaporator clear. Plugged unit in and ran through diagnostics. Unit passed all tests. Called techline and went over finding. Techline suggested replacing the control. SR#7739487048; ordrng 1 W11035836 (Control)

Freezer door wire harness faulty. New door ordered W11536873 ; ordrng 1 W11536873 (Door)

Gas pressure 13' Case#13608037Spoke with Ge Techline. Techline advised to check gas pressure at wall if gas pressure is good to check for 120 V at gas valve. If all is present remove and replace gas valve assembly again. Part ordered ; ordrng 1 We03x29303 (Gas Valve)

"JB out 7/12/24.Customer states the refrigerator section is not cold enough also freezer. No ice production.Upon arrival, found Mullion divider burning hot to the touch.Pulled unit away from wall. Removed unit cover. Fount condenser fan blade worked its way off the motor shaft (over time) until it became blocked from turning causing condenser fan motor failure. Estimate to replace both Condenser Fan Motor and Fan Blade isCondenser fan motor part # 242018301. $136.20Fan Blade is. $. 23.41Tax on parts. $. 11.57Labor. $217.92Service call/Diagnostic charge $145.00TOTAL REPAIR ESTIMATE IS. $534.10Estimate has been approved 7/12/24Collected Parts, Tax and Service Charge ($316.18) Paid by CC on 7/12/24Authorization code 9T39 VM, transaction ID 1371672BALANCE DUEON COMPLETION OF JOB IS $$217.93ORDERING PARTS; ordrng 1 242018301 (CONDENSER FAN MOTOR) and 1 241639502 (FAN BLADE)"

"File number 7739488648.Called techline they wanted me to try to seal behind gasket in order to retainer gasket better. But groove fits into is too wide not making a good fit. Will need to replace the fresh food door. Door seal has a tear at the top, will order and replace both parts.; ordrng 1 W11449026 (Rr ff door) and 1 W10917313 (Door gasket)"

Ordering pre cooler leak seems to be coming from it. Ordering part; ordrng 1 W11189542 (P cooler)

Wrong part. Did not come with burner & valve assembly as per diagram. Need the one with gas pipe.; ordrng 1 WE11X35317 (VALVE & BURNER)

Right side door gasket is ripped and ice maker is dripping into ice bucket in the rear. Ordering ice maker and right side door gasket. ; ordrng 1 W10830274 (gasket-fip) and 1 W11548540 (Ice maker)

When I diagnosed unit the drain pump was draining normally and the cycles were completing I had ordered suspension due to customer stating that the clothes were left wet. I arrived today and the drain pump is not draining and just humming with no obstruction indicating that the pump was failing intermittently. Need to order drain pump. Will use valve and suspension on return. ; ordrng 1 W10919003 (pump-water)

Removed and replaced drain pump. Unit now draining and Im able to test unit. I found that the wash motor is locked up causing no wash movement. Ordering sump assy and will install console on return. ; ordrng 1 W11416363 (Sump assy)

Checked unit found bad led module in rc. Also Cx experienced po code intermittently about 3 times. Ordering parts for repair ; ordrng 1 W11321365 (Main board) and 1 W11387579 (Led module)

Found unit not finishing spin cycle; ordrng 1 WH22X37220 (Control board)

Need more time to install parts; schdld next appmnt for 7/15 MON !

Both cabinets are totally hot and compressor is seized. Will need sealed systems tech for repair.; ordrng 1 WPW10507886 (Compressor) and 1 W10843121 (Drier)

"Found refrigerator deli light off Ui all lights on called manufacture need Ui drawer.case#87409848. Board dispenser control and mother board per manufacture sending correct partnumbers .; (created new UIS, deleted prior attachment to UisID 443875)"

Found dishwasher not responding power ok .; ordrng 1 WD21X24676 (Control) and 1 WD21X32839 (Ui) and 1 WD34X24733 (Cover)

"Case #87410522. Found refrigerator on demo mode removed retest out ok complete.; (created new UIS, deleted prior attachment to UisID 443514)"

Found dispenser assembly leaking cracked will order; ordrng 1 W11524105 (Dispenser assembly)

"Washer turn on by itself, cant ran any test,control board not responding.reroute for parts.; ordrng 1 W11608056 (Cntrl board)"

Cycled unit and found bad LED. Ordering part for repair.; ordrng 1 W11602886 (Led module)

Not drainingFound bad pump after clearing. Unit is stacked. Dryer on top. Need help removing Need two techs 4 call count *****; O-emld tckt

"Shawn with tech support, recommended to look up Service bulletin # REF 03-24 regarding fill tube heat tube kitWR49X45545Water valve, Main board and Ice maker; schdld next appmnt for 7/13 SAT !"

Tested unit found sound coming from defective drum and pulley.; ordrng 1 WE21X23869 (Drum asm) and 1 WE03X27417 (Pulley)

"7816 Isaak Ln Bakersfield Ca 93314 is correct addressF2E1 stuck key and thermistor sensor code tested both , operating ok now at this time , prior to coming out, the unit would run for five minutes and shut off on its own no matter what setting you put it on estimate to replace the user interface console is $ 788.01 Mrs declined to have anything done , unit tested ops ok now at this time paid $145.00 trip charge by card ; ordrng 1 W11419056 (Console)"

Tech was assigned as a helper;

Installed new pump and new latch. Unit is still having problems trying to start a cycle. Confirmed we are losing voltage at pump. This indicates a short in the wiring harness or faulty control. Instructed customer they will need to get washing machine moved out and have somewhere more accessible for us to be able to do this repair. Ordering components needed.; ordrng 1 W11591637 (Harness) and 1 W11633362 (Cntrl)

Confirmed broken wire to pump. To short to repair. Will order and replace lower harness. ; ordrng 1 W11643701 (Lower harness)

Found that units hinges were defective not allowing lid to shut properly. Defective hinges put stress on lid and damaged lid. Customer had unit completely installed advised customer they would have to have unit hooked up next time for me to test.; ordrng 1 W11128305 (Hinge left) and 1 W11128306 (Hinge right) and 1 W11128271 (Lid)

Guard let me in with a name. Address entered in incorrect. Called customer via 3CX no answer. Called office who also called with no answer. This community is set up by village numbers. Example: village 6 unit ****. Will need to be rescheduled. ; saved tckt

Reordering data loggers to ensure no further cooling issues. If temps are in fact in range then ice maker and fill tube heater should be replaced. ; ordrng 1 Datalogger

Needs compressor as well. ; ordrng 1 5304530688 (Compressor)

Ordering correct sump motor.; ordrng 1 W11460946 (Motor)

Called Frigidaire tech line to help verify the issue with the noise complaint. Unable to verify the noise complaint. I was able to verify the power outage issue and that was the main control. As soon as I pulled it out and started charging the connections the power outage came on the display. I replaced the main board and the display board. We will see if that takes care of the noise and power outage issue. There are two new doors to install but only one gasket and the right side door has no name plate. Will order and replace on return. 87410623. ; ordrng 1 241778307 (Gasket) and 1 5304512150 (Nameplate)

Actuator was removed and replaced. Unit will need additional part. Capacitor shorted out. Part on order follow up required. ; ordrng 1 W11428524 (Capacitor)

Unit will not start; ordrng 1 W11627517 (ACU) and 1 W11700916 (Latch)

"Compressor is locked up, send out sealed system tech.; ordrng 1 W11580057 (Compressor) and 1 W11504415 (Coupler) and 1 W11504431 (Coupler) and 1 W11506619 (Coupler)"

Will reschedule call unit did not need Yvette fan motor towed customer that unit will need defrost thermostat due to ice buildup put unit in diagnostic mode and ran test number two which show that the heater turned on and I also ran test 15 which showed me that the fan motor turned on; ordrng 1 5304522323 (Defrost thermistor)

"Upon arrival found unit with noise coming form the back of the unit. Check the unit and compressor is running with normal noise, check the condenser fan and dont run at all. Run a test 4 and condenser fan never kicked on, check voltage and is no present the 120 DCV. Call tech line and after inspection, DC voltage is no going out from the control board. Recommendation is replace the control board and ui. SR: 7739488166; ordrng 1 W11620204 (Cotrol board) and 1 W11608967 (Ui) and 1 W11127829 (Motor fan) and 1 W11608966 (Fan assembly)"

"Upon arrival found unit with door no closing properly, causing the door in uneven position, check the unit and found the lid is damaged in right front corner causing a sharp edge, and is dangerous. Additional the hinges on the unit dont work properly and is causing the door bags down, this unit will need new lid and hinges. ; ordrng 1 W11404468 (Lid) and 1 W11551369 (L hinge) and 1 W11551369 (R hinge)"

Broken wires on pantry door.; ordrng 1 W10815669 (Pantrydoor)

Installed parts tested unit still winding need transmission.; ordrng 1 WH03X34937 (Transmission) and 1 WH43X31240 (Auger) and 1 WH43X34257 (Assembally)

Ice maker e5 error code and damper noise. Needs ice maker fill tube heater sealer and damper; ordrng 1 WP505587 (Sealer) and 1 WPW10479155 (Damper) and 1 W11087201 (Heater) and 1 W11658802 (Icemaker)

"Noise when agitate , needs Gearcase ; ordrng 1 W10902814 (Wash plate) and 1 W11449841 (Gearcase) and 1 W10734521 (Slider)"

Fan not working ice melting. ; ordrng 1 W10846539 (Ice fa n) and 1 W11578030 (Fan freezer) and 1 W10864518 (Fan kitn)

"No error codes found, same scenario from last visit, Cerama Bryte Washer Cleaner and Brush set are recommended for ease of usage by Cx and proper cleaning of unit.; schdld next appmnt for 7/15 MON !"

"Ice maker slow to cycle , freezer temp is 1 degree at this time determined failed ice maker ; ordrng 1 W11700250 (Ice maker)"

"Replaced compressor, dryer, installed low side access port, leak checked with nitrogen, recharged unit, unit cooling at this time. Seal system warranty job."

"The washer has a long fill code. Test the valve, confirmed slow filling from the valve. Replaced the valve. Restored power confirmed repair, running diagnostic cycle. All functions normal. FIN"

"Not cooling, found 110 plug to inverter loose , reinstalled plug and tested unit working properly"

Install the new compressor and dryer

Replaced faulty damper was making a clicking noise. Tested after repair all ok.

"A new drain plum and hose were replaced, functional tests was conducted while the house sitter was observing."

"Fresh food section damper control damper making noise , remove damper and install new one reset unit so it can resume normalizing temperature for proper operation, job complete."

"Replaced inner oven door panel, checked door functions,unit operating as designed."

"Support for bracket was broken, replaced with new one. Unit working properly"

Fixed- found broken coupler causing ice not to dispense- removed bad one and then installed new one (coupler) ice is now dispensing- cx ok repair

"Replaced drain pump, checked & removed obstruction from drain hose, ran self diagnostic cycle, unit operating as designed"

"Main board and defrosting element will need replacing and steaming out ice behind back wall in freezer section Job complete."

Installed new components. All ops now working as designed.

"Installed drawer, tested, unit functions as designed."

Found obstruction in pump causing F9E1. Removed obstruction. All tests good.

"Fixed- found right side door gasket to be ripped, magnet has fallen out causing closing problems- removed bad one and then installed new one (gasket) removed wrinkles with heat gun- door is now sealing to cabinet- cx ok repair"

"Replaced control board, found a broken wire to drain pump, spliced it and now unit is draining, Cx cleaning unit as needed, tested and washer is now working properly,Job complete."

Replaced control. Tested unit. Unit operating as designed. Job complete. $353.68 CK Auth# 49HLJM

Unit is not draining and giving F9E1 code. I found voltage to drain pump but pump not responding. Failed drain pump. Removed and replaced drain pump. All tests good.

"Installed Icemaker, verified unit is operating as designed"

Install the new chute and coupling on the unit. Retest the unit and now is dispensing ice correctly. Job complete

Installed new wheels. Unit complete.

Over suds. Leaking into tray and reading water w suds. Cleared and tested. Confirmed too much soap. Ran and cleared about 6 times to remove soap build up. Cx instruct on use and care. Unit working as designed.

"Washer out off balance.suspension hits bottom, replaced suspension test cycle ok"

Ice maker was removed and replaced. Unit passed all test. Unit is working as intended.

Replaced timer. Tested unit. Unit operating as designed. Job complete.

"Ice maker,was removed and replaced. Unit I passed all test. Unit is working as intended"

Replaced defective ice maker and cycled unit.

"The main freezer rails have become jammed. The door were hard to close, and seal. Removed rails, installed replacement. Assembled unit, test the door. Door open/closes properly and seals. Done."

"Customer stated unit is making noises, I secured back panel and lines to the condenser , unit is now operating more quietly as designed, cx approved adjustments at this time of service"

Replaced switch all tested good

Replaced led modules. Unit operating as designed. Job complete.

Found breaker left side open reset break product tested ok complete

"F0/E2-over sudsCleared the error code. Ran the components test. All check good. Ran calibration cycle completed, but has a loud noise when the unit shifts. And agitates. Removed power, replaced the belt, cam and actuator. Assembled the unit restored power. Calibrated the washer, passed. Filled unit and allowed to agitate, all functions and sounds normal. DONE. ; used 1 W10006384 (Belt), 1 W10913953 (Actuator), and 1 W10721967 (Cam) from stock"

"Control not responding, repaired control connections and tested unit on fill, wash ,drain and spin tested properly"

"Cx states dw leaking from left side of door. Cx had pictures and video. Tub seal has soap build up, preventing it from making a proper seal. Cleaned tub seal and mating surface on door. Tested unit. Unit operating as designed. Job complete."

"Codes F0E2 over suds.Customer complaint is it sticking in add agitation mode for hours, they have to shut unit and restart. Changed main board. Ran diagnostic cycle test passed all test . Job complete."

Installed the new user interface and dryer OK

"Job complete found piece of ice stuck on the icemaker arm, not allowing it to return to home position which is why the unit did not produce any ice after removal. Ran test number 25 and everything checked out OK customer saw everything that I did job complete."

Wont spin or lock. Unit broken latch and strike. Removed and replaced now working as designed

Upon arrival inspected unit found unit not cooling correctly. Inspected compressor. Found his compressor replaced compressor. Pressure tested unit at 213 psi unit held pressure for over 30 minutes charged unit with 66 g of our 600 a advised consumer to give unit at least 48 hours for the unit to get back to temperature. All ups are normal job complete.

"Not heating and seal bad, replaced seal,adhesive,switch tested unit working properly"

Unit became unleveled causing door not to close properly. Leveled unit and fixed door closing issue. Now opened and closing as designed. Unit working as designed

Slide has fallen down. Replaced slider.Ran diagnostic cycle test all passed . Job complete.

CX says the mullion is not striking properly. Found the door needed adjustment upwards. Installed correct door setting. Mullion is activating properly. Done.

"Checked the unit repaired the latch asm , tested ops ok now at this time"

"Noise from blower . Found blower wheel loose on motor shaft. Retorqued blower wheel. Tumbling and heating properly at this time. Instructed customer to replace gas connector used, too short, and flexible duct with semi-flexible aluminum ( not foil ) duct with elbow. Complete."

"Tested unit and found defective door seal on freezer door and right freezer door glide damage, fixed freezer door glide and freezer door seal, tested unit and is working properly, customer instructed on use and care of unit"

Found a bed in a minute lunch assembly had it replaced washer ok

"Cx stated unit doesnt lock or start cycles. No error codes stored on unit. Performed diagnostic cycle. Diagnostic cycle completed successfully. Started and canceled a quick wash, normal wash, and bulky items cycles. Washer started all cycles. Unit tested lid lock, began sensing, locked lid and then began to fill. Cx was not holding the start button down long enough to begin cycle. Start button must be pressed and held until all lights are lit. Unit operating as designed. Job complete."

Found loose start device connection so I replaced start device and all fans kicked on. Unit functions as normal.

Cycled unit and found bad connection.Two heater connector black wires period secured connection and retested unit.Now working as designed job completed

Found dryer screeching found back left foot loose reposition retest ok complete.

Unit not starting. Ui panel peeling off. Requires control and ui panel. ; ordrng 1 W11460962 (Ui)