"Installed and secured new freezer door, tested unit for leaks, no leaks visible, unit should make ice and operate properly as designed at this time of service, customer approved repairs"

"F10e1. F6e6. F6e1. F3e3. Cleared the error codes, ran diagnostics, the units wash motor is not pumping properly, the spray arms are hardly moving. The customer reports when the rinse aid compartment is filled, it only takes a couple of days for it to empty out. The sump and motor assembly, and dispenser need to be replaced. Provided an estimate to the customer, they decline the repair, will replace the unit instead. Charged for the service call fee on the second appliance at home ( refrigerator)."

"Because of a rattle noise and drum not stopping even when dryer was off, a complete new dryer repair kit along with a blower wheel have been replaced, Also, a yearly maintenance has been performed.; used 1 WP697772 (Blower wheel) from stock"

Upon arrival found unit with no lights on the freezer section causing failure. Install the new LEDs on the unit. Retest the unit and now unit has properly light on. Job complete

Installed heater tested unit needs to be defrosted before use

Found wheel stripped replaced tested working properly ; used 1 WP697772 (Wheel) from stock

"Found the unit, not cooling, unit not have refrigerant, replace service and charge nitrogen verify leak in discharge line in condenser, repair leak make a vacuum,charge refrigerant 69g R600a check compressor condenser and evaporator fan motors work normal ; used 2 W11506635 ( Service valve) from stock"

Installed new light module. Lights in unit are no longer strobing. Instructed customer on how to reset filter light. Instructed customer on how to remove ice bin so they can be sure to dump ice after long periods of not using.

"Upon arrival found unit with bottom drawer no working. Check the unit and unit has a bad control board. This unit need a new control board, unfortunately this part is no longer available. Inform this to the customer. Job complete"

"Pulley sticking and want rolling smoothly. Replaced belt, pulley, and rollers. Dryer no longer squeeking."

"Replaced slider. Then, ran calibration, and factory test. Washer checked; used 1 W10734521 (Slider) from stock"

Replaced main board ok now

Installed part tested check out ok complete no dents or dings cause by tech.

Replaced control ran unit through diagnostics cycle all functions are working properly job complete

Replaced shelf and bin all tested good

"Replaced the main board and dampener control , asm tested operations ok now , allow 48 hrs to get back to normal temps"

Customer concerns. Refrigerator not powering on. Power cord was disconnected from cabinet harness. I re-connected harness. Operation tested as designed.

After replacing the faulty door gasket it is now staying in place and sealing well. All tested ok. Job completed.

"Removed defective unit. Installed new unit. Tested new unit, works as designed."

Found water in the area where the detergent. Replaced drawer and tested. Unit is working properly. Customer approves. Ran test cycle and found all functions working as designed.

Found water in the area where the detergent. Replaced drawer and tested. Unit is working properly. Customer approves. Ran test cycle and found all functions working as designed.

"Removed and replaced rear bulkhead, motor, clamp, blower and repair kit. Tested unit. All tests good."

"Removed and replaced coil valve, tested ops unit now working as designed."

"Installed and secured parts listed, tested unit, unit is now heating up and operating properly as designed at this time of service, customer approved repairs"

After replacing all parts ordered the u it is no longer making the abnormal noise and the blower was cracked and caused the motor bearing to ware. All tested ok after repair. Job completed.

"No fault codes were present, ran diagnostics cycle, diagnostics cycle completed with no errors. Verified that the heating element is functioning. Verified that the drain pump is functioning properly. Customer stated that they use rinse aid. Customer has an issue with water droplets and water condensation that is still present after two days of the dishwasher sitting with no use. Advised customer that I would document this issue with the manufacturer. Unit is functioning as designed. Sr# 7735891614, documented with trade care also."

Removed and replaced drain pump and lid lock. Tested. Now drains and locks as designed Job complete

Replaced led module with correct lights. Service pointer listed on issue.service pointer W11606409 and s code S84638

Installed new door. All functions now checking normal.

Cleaned out a bunch of coins from inside the dryer. Tested unit is sounding good all functions are working properly

Customer stated that spring is missing and bezel came off. Removed and replaced bezel and spring tested all works good at this time.

"Unit was not putting in hot water only cold water last visit ordered valve and this visit replaced it, issue was fixed tested after repair and both water cold and hot where coming out, no further issues, job completed."

Found unit clicking on low. Found front left and front right burner head swapped causing the flames not to be directed properly. Swapped burner heads and tested. Unit is working properly.

Upon arrival found unit with gasket on the fresh food section fell on the top part causing failure. Apply silicon on the gasket so that way they can be proper install. Inform the customer day and night they need to put something heavy against the door on the fridge so that way the silicone can glue it correctly. Returns the unit and now unit is working properly. Job complete.

Install the new parts on the unit. Retest the unit and unit passes all test at this time. Job complete

"Unable to duplicate complaint. Tested operation, ran diagnostics. All ok! Advised customer of proper operation"

Upon arrival found unit with long periods of time for drying. Check the unit and found the vent is clogged causing the failure. Inform this to the customer. They need clean the vent in order to the unit work back properly. Job complete Additional found gas leak on the left side of the washer inform this the customer so they can call gas company. The dryer dont have any leaks on the connections.

Replaced grill and modules. Fridge ok

Selector switch is faulty Part no longer available

Installed parts could not test unit with out gas customer needing 220 dryer no gas called there office aware complete ok to be billed per r office .

"Removed and replaced door and ice container, tested ops unit working ok"

"Replaced valve, dryer, Access port , also replaced evap cover, recharged system with 4.5 oz of 134A still no flow to fresh food evaporator, set valve to fresh food evap, cut at dryer and pressurized system to 149 psi still no flow to evap determine restriction in capillary tube to fresh food evap contacted tech line sr# 7735892029"

Cx exhaust that goes out to house was completely blocked and exhaust was crushed and extremely long Advised cx to clean that out and get short hose Complete

"Checked the unit dead , customer self cleaned , then cooled off ,then the control fuse went bad - cx approved , tested operations unit now heats correct at this time

Found the unit had a loose connection at the gas coils. After reinserting the coil connector that restored the heat. I ran a vent test as well and recommended the customer have it cleaned out. Dryer isolated passed the tested. Heat cycling test passed. Job completed.

"Checked the Left front power burner was not igniting when cold , aligned up the power burner correct and and widened the upper left port , ops now work correct, power burner now ignite correct at this time"

"When I was closing the door I noted some of the LEDs were lit. I checked for fault codes and ran a service test. The unit had no faults and passed its service test without generating any new faults. Found the end of the power cord connected to an adapter that was loose when I disconnected the power. Checked for secure wire nuts. Both lines were secure and there is no evidence of overheating. Opened panel and removed the door latch. During inspection, when I was actuating the latch, something flew out of it. I could not find what that might have been. I lubricated the latch and reinstalled it. I checked all the harness connections and applied a dielectric compound to the connections for better conductivity. Reassembled unit and ran another service cycle. The unit completed the cycle without fault. Started a normal cycle to make sure the unit works in consumer mode. Aligned the door to the latch for better closing. The strike was forcing the door slightly left. Currently the unit is operating a s designed. Informed the customer the service charge is valid for 30 days and off the unit should act up they could recall service without another service charge. The unit seems to be in good condition. I focused on the latch and connections since this was the most likely issue other than a control failure . Both are checking ok currently."

"On arrival unit has no ice, found broken wires at lower hinge of fc door. Needs door. Advised Cx to seek assistance as repair is costly. Cx paid service fee."

"Installed the sump and motor assembly. Ran diagnostics, diagnostics completed with no errors present. Verified that No leaks are present. Unit is functioning as designed. Did not install the board and drain pump.

Repositioned drain line. Drain line longer hitting tub during spin cycle and making clicking sound.

"Replaced freezer door, checked ice maker functions, unit operating as designed."

"Heater is drawing .9 amps, water valves are .4 amps, unit in run cycle drawing .3 amps. Polarity and ground is all correct. Called tech line and theyre only willing to write a report but not will not condemn the unit. Received a service number 7735748056"

Customer stated that the unit is not washing the dishes. Found sump is not working. Quoted customer for replacement.

Upon arrival found unit with cover for the motor and belt fell into the ground cows in the noise when the unit was agitate. Readjust the cover and return the unit and now unit is working properly. Job complete.

Removed and replaced heater assembly. All OK.

Installed new drain pump

"Assembly oven bottom was replaced because old one was bended, also cap was replaced because of smaller size, no further issues, job completed."

Off balance load error. Removed and replaced slider. Tested operation. All ok!

Replaced faulty capacitor has zero microfarads. Tested after repair all ok.

Installed liner kit. All functions now working as designed.

"The rotor was replaced because when put on a drain and spin the rotor was not spinning or agitating, once replaced retested with drain and spin and this time saw rotor move correctly no further issues, job completed."

Found actuator bad replaced tested working properly

Removed and replaced main control and coin interface. I calibrated unit in diagnostic. Unable to test coin mech due to keys for washer not being at apts at this time.

Removed and replaced main control and coin interface. I calibrated unit in diagnostic. Unable to test coin mech due to keys for washer not being at apts at this time.

Replaced control board. Washer now working properly.

Unit not cooling. Tested unit and found evaporator fan not running. Removed and replaced fan motor. Tested unit. All tests good. ; used 1 WP2315549 (EVAP FAN MOTOR) from stock

Found idler bad replaced with dryer kit tested working properly ; used 1 4392065 (Kit) from stock

Removed old unit installed new unit tested new unit new unit operating as designed had a nice wide path for the refrigerator to get through. It was just move forward and out the door.

"JB out 3/7/22 customer states washing machine does not spin, clothing, dryer, efficiently and clothes are left wet at the end of the cycle which requires more time in the dryer. Upon arrival found test wash load just ending and verified small amount of laundry quite wet. Found customer had selected casuals cycle. Explain to customer casual cycle will not spin at a high rate of speed as towels, bulky items, heavy duty or whites cycles. Recommend customer select one of these cycles for a higher spin speed which will extract more water requiring less dry time in the dryer. Also advise use of HE detergent only and very, very small amounts typically that of 1 teaspoon maximum. No mechanical issue found. No repair made or needed. Advise customer of one time courtesy no charge on a no defect. Sound service call visit. No charge to customer. Job complete."

Installed new pump and unit now functions as designed Complete

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

Cycled unit and found bad slider. Installed new slider. Retested unit passed all tests job completed.; used 1 W10734521 (Slider) from stock

Installed all parts listed no leaks working properly

Replaced thermistor and main control.

Replaced parts and tested unit job complete

Replaced all refrigerator and freezer light modules ok now

Removed and replaced main harness and main control at the same time. Tested unit. All tests good to 350 on bake and broil working normally. All tests good.

Installed new parts. Operation tested as designed. No gas leaks at time of service.

Removed and replaced board cam cap and actuator. Ran test. Now working as designed. Job complete

Found defective blower wheel. Fixed blower wheel. Tested unit and is working properly. Found dam vent informed client

Installed new drive hub and capacitor. Recalibrated and unit is working per design. Job complete

F9E1 error code. Found unit had a kinked drain hose. Removed kink and tested. Unit is working properly. Customer approves function at this time.

"Unit was tested with service test gave no issues and there was no error codes although did see some installation issues with Cx drain hose there where not using original one and the one that was there was extremely long and on the floor this would be Cx issue why she having problems, Cx will have to correct issue and fix drain hose, no issues with unit, job completed."

JB out 3/7/23. IVerified top 6 LED modules in RC non functional. Also FC LED non functional. Installed replacement LED module (W11601310) in FC restoring all LED modules functions.Tested operation with customer. No charge. JOB COMPLETE

Installed new sump. All functions now working as designed.

Replaced bulb and main board due to lite keeps blowing out.Tested ok

Found dishwasher not washing found bad sump pump replaced retested check out ok complete no dents or dings cause by tech.

"On arrival unit not draining, quoted Cx to clear filter, Cx approved. Cleared filter from front seal and tested, unit functions as designed."

Inspected unit found cutoff blown. Replaced and found heat element only half heat. Replaced and unit passed all tests. Job completed

Installed part magnetron giving small vibration rethighten retested check out ok complete no dents or dings cause by tech.

Installed springs

Installed transmission tested working properly

Checked out and ran diagnostics test. Ran cycle and found shipping rod was still in and causing major noise. Unit is now working as designed. Unit now washes filled and is working like it should. No noise. Test passed and working. Job completed

"Found the unit, not cooling, verify problem compressor not running, replace compressor, service valve, capacitor and relay, make a vacuum, charge refrigerant 48g R600a check compressor condenser and evaporator fan motors unit work normal ; used 1 W11506635 ( Service valve) from stock"

Installed new suspension rods and tested unit working as designed

Installed new keypad and knobs retested unit all tests passed pass. Job completed.

Found the gearcase leaking. Also valve not closing on the hot side. And capacitor not allowing motor to start.

Not cooling fresh food compartment. Unit is making ice. No air flow in ffc. Removed fan cover. Fan not spinning. Removed and replaced evap fan motor. Installed fan blade. Now working properly. Cx to wait 24 hours for proper temps. Job complete.

Replaced broken door glass. Testing door and is working properly.

"Upon arrival found unit with error codes F8E5 and F10E2, causing failure on the water valve and the vent. Erase the codes, retest the unit and water valve has a test according with the tech sheet, and the vent was passing the test to. This unit is working properly. Job complete."