Installed new ice maker and inlet valve. All functions tested okay. Unit working as designed. Call complete

Fan motor making loud noise replaced motor fan is on and running loud noise is gone. Job complete

Replaced latch tested door is closing properly Job complete

Customer states that unit is not working properly After running diagnostic test find that unit has a bad sump motor Replaced all selected parts Unit working properly as required

Replaced moisture sensor from my stock Tested unit working properly as required

Replaced all selected parts Unit working properly as required

Customer states that unit is not draining After running diagnostic test find that air gap is clogged Unclogged air gap Tested unit working properly as required

"Diffuser stuck and making noise, Replaced diffuser , unit running to specs.Job completed"

"Unit was found leaking, clogged with liquid soap under dispenser,door lock was not working, replaced door lock, tested and run unit which is now working to specs. Job completed."

"Unit not responding, found defective door latch, replaced latch, tested and run washer now working as designed.Job completed."

"Unit has rollers making noise.Replace dryer kit, tested unit,runs good as designed, job completed."

"Found door latch broken, replaced, tested and unit runs properly. Job completed."

"Unit has a bad capacitor, replaced cap, tested and washer runs properly.Job completed."

Removed and replaced console. Tested unit. All tests good.

Installed suspension rods and tested unit. Unit is working properly. Customer approves function at this time.

"Replaced light modules working as per designed, customer approved. Job complete."

JB out 12/14/23.Installed replacement TOP WH10X33077.Reassembled unit and tested operation with customer.Unit now operates as designed. No Charge To Customer JOB COMPLETE

"JB Out 12/14/23.Customer states with the dryer has little heat and takes several hours to dry clothing.Upon arrival found newly installed dryer in laundry room connected with thin foil type ducting material going inside wall above kitchen to the exit of the house. Tested dryer with wet clothing. Found unit is heating but short cycling. Burner flame says on between 23: 45 and then cycles off. Remove the dryer from away from the wall and then remove ducting from dryer. Tested dryer again in timed dry cycle. Verified burner does not any longer short cycle. Counted 11 1/2 minute on interrupted burner duration with wet clothing and dryer. Advise customer no mechanical issue with dryer itself but ducting system inside wall to the exit of the house is partially restricted causing short cycle burner operation lead to very long dry time. Recommend customer replace existing thin foil, tight ducting material with rigid metal ducting material to prevent potential hazard of fire or loss of life. Also recommend customer have duct inside wall, professionally cleaned to remove any and all restrictions. No charge to customer. Job complete."

Tested unit found deffective float switch, fixed defective float switch tested unit and is working properly

"Tested unit and is working properly. Checked shut off valve. Checked dryer, gas valve and checked connection to dryer gas valve. No leaks found at this time."

"Found effective drum kinked to back of unit, fixed defective drum, tested unit and is working properly."

Fixed defective drain pump. Tested unit and is working properly.

"Installed dryer, slides and unit is quiet now."

Removed wall oven and Installed new ui and retested unit now working as designed job completed

Installed new parts and retested unit now working as designed job completed

Unit latch broken and will not lock. Installed new lock and unit is working as intended.

Installed ice maker and jumped connection t and h. Unit working at this time

Replaced front right burner base. While testing oven gfi on counter blew. Advised customer that unit must be on dedicated circuit.

Install evaporator cover panel on fridge worked OK

Installed the new couch assembly now door closest properly

Installed the new doors boot. Washer ok

Installed new control board and dryer worked OK

Replaced parts listed. There was a hair line crack on blower wouldnt come off. Replaced and tested. unit is now working properly and as designed. Job completed

Unit is not lock. F5e3 lock failure. Found and replaced lock mechanism and tested unit and made sure lock is functioning correctly. Passed test. Job completed

Found harness was bad. Replaced and checked out. Checked all functions and unit is working. Job completed

"Removed power rom washer, replaced suspension cam and belt. Assembled unit, restored power. Ran and passed calibration cycle. DONE."

"5.5z 134ARemoved charge from sealed system. Removed pre-cooler and filter drier. Installed pre cooler, filter drier and access stub. Vacc and charged the fridge to recommended level. Unit is holding charge. ALLOW 24 hrs for unit to settle temps. DONE."

Installed components test pass. No leaks door seals properly. DONE

"Moved and replaced units, rollers belt and rest of drive kit. Also secured loose blower wheel facia plate. Ran unit for five minutes. No noise customer approves function."

Installed new water valve product tested ok complete

Installed oven probe and bake igniter product tested ok

Replaced element that was grounded to box replaced thermostat cut off and high limit came with thermo cut off sending other high limit back product tested ok complete

Installed new drive motor belt actuator and cam kit product tested ok complete

Replaced failed pressure switch product tested ok failure code clear complete

"Uninstalled unit, removed and replaced fill valve, harness,and inlet water flow meter. Asked customer to monitor and report any issues"

"Checked unit found latch connector not fully inserted into control, re inserted and unit checked ok."

"Found metered wheels on bottom rack, removed and replaced rack unit now working properly."

"Found unit within model and serial number for led module replacement. Removed and replaced all led modules, unit now checking ok"

"Removed and replaced door, tested ops unit working ok. Customer will monitor ice production."

Install the new harness control board and thermistor on the unit. Retest the unit and now unit is working properly. Job complete.

"Upon arrival found unit no working properly on the door switch, check the and found the primary switch is bad, this because is no continuity on the normal close, causing the failure of the error message on the screen for the door. Install the new interlock assembly, retest the unit and now unit is working properly. Job complete"

"Upon arrival found unit with error codes F7E7, F6E3, F7E4 and F7E3, this about motor problem and clutch. Check the unit on test mode and the unit doesnt agitate or spin. Check the unit and found the harness is back and additional the control board as well. Replace this two components on the unit. Retest the unit and unit is working properly. Job complete."

Pulley was removed and replaced. Unit is working as intended. Job completed.

Replaced harness. Tested unit. Unit operating as designed. Job complete.

"Locked rotor. Replaced compressor, pressure tested, checked ok. Pulled vacuum, recharged 50g r600a. Refrigerator operating as designed at time of service."

Replaced oven console. Operation tested as designed.

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

"Unit had deformed freezer door gasket, used steamer to soften"

"Unit had bad water valve, replaced and tested unit , working as designed"

Removed and replaced Eva cover an air tower. Unit functions normal now

Lid was broken. Removed and replaced lid and tested unit. Unit functions normal now.

"Fixed- installed new parts (gasket, cntrl elec) temps are working at control- gasket is sealing to cabinet- customer ok repair"

Fixed- installed new part (compressor) pressure tested with nitrogen- pulled deep vacuum- charged unit with 68 grams of r600- unit has begun cooling- 12-24 hrs for temperature to stabilize- customer ok repair

Fixed- installed new parts (5 knobs) customer ok repair

Customer is still under 30 days from original job with concessions. Unit would not dispense ice. Faulty auger motor and yoke on ice container is worn. Installed new auger and ice container. Unit now dispensing ice with no issues. All functions now working as designed.

Found hi limit thermostat out of position with a loose connection. Re secured connector back to hi limit and installed to proper position. Unit now heating and functioning as designed.

"Found frozen fill tube for ice maker heeling ice maker from filling, cleared fill tube all tested good"

Repulsed gear case and wash plate tested good

Replaced evap fan motor all tested good

"Belt shredded got cough on cover, replaced belt tested good"

Replaced oven burner and retested. All gas is igniting

F1E2 and F3E3 present. Replaced control. The last control installed was defective. Recalibrated and ran diagnostic cycle. Faults did not return.

"Found the unit's compressor not working properly, replaced, cntrl-elec and inverter-box, check compressor,condenser and evaporator fan motors, unit start work"

"F7E4, Checked the unit the washer had a bad slider , replaced slider with truck stock one , tested operations ok now at this time ; used 1 W10734521 (SLIDER) from stock"

"Unit not heating water, removed unit from cabinet, Found no power to transformer, found mounting screw missing from left door microwave/ interlock assy, remounted micro switch assy on left side with screw, ran water heating test, unit operating a# designed."

"F2E1, F9E1, F8E1, F3E1, found pressure hose crimped at back of tub assy close to tub port, adjusted pressure hose location, ran self diagnostic cycle, unit operating as designed."

Customer stated that the unit is not washing. Removed and replaced sump assembly tested all works good at this time.

Customer stated unit makes noise. Found diffuser makes noise removed and replaced control motor tested all works good at this time.

"Replaced ACU, latch. Had f3e1 error code. Replaced pressure sensor. Console is working properly at this time. Locks/ unlocks, fills, washes, drains,,dispenses, and spins properly at this time. Complete."

"Ran diagnostics. Had f8e1, f0e3 error codes. Learned error codes. No cold water. Found cold water solenoid cracked. Replaced water inlet valve. Locks/ unlocks, fills, agitates, drains,,dispenses, and spins properly at this time. Instructed customer not to wash rugs, bath mats, comforters, drapes, curtains, pillows, dog beds, shoes, bed covers, sleeping bags in a domestic washer. Complete."

Replaced hub. Dishwasher working properly.

Replaced water valve. Washer now working properly.

Replaced bad lower harness causing intermittent power supply to the drain pump. Unit test ok. Complete

"Replaced led lights, unit works fine. Complete"

Replaced broken adjusters. Now upper rack rolls in and out properly. Unit ok after repair.; used 1 W10712395 (Adjusters) from stock

Replaced all lights in service kit. All ok all lights now working. Unit ok after repair.

Replaced broken door strike. Tested after repair all ok.; used 1 W11457841 (Strike) from stock

Found ui board not sending signal to control board F2E2 error replaced ui board retested unit unit working properly

Found faulty thermal fuse replaced fuse tested unit unit working properly

"No power to drain pumpHarness connection was not seated, repaired and reconnected with as designed operation returned."

Noisy Confirmed.reinstalled loose blower assembly..designed operation was restored.

"Returned, replaced defective part and as designed operation was restored. 1 W11590251 (Valve) and 1 W11590292 (Regulator)"

Starts then after approximately a minute machine advances to done With no wash action at all, Replaced broken slider. As designed op returned.

"Found after replacing the main control, sister board, and both user interfaces for the ovens. That restored the operation of both oven. The oven lights are also optional. Job completed."

"Upon arrival, inspected unit, found that the unit had a loose connection in the power box causing unit to stop running occasionally could not find a leak was able to put new wire nuts tested unit unit passed all tests job complete"

"Installed left rc door, tested, unit functions as designed."

Removed and replaced all parts. Tested now working as designed.

Found unit with loud wheels. Removed and replaced dryer repair kit. Now working as designed.

"UU panel, motor, water valves changed out. Removed listed parts. Installed new listed parts. Test ran unit. Unit operating as designed."

"Heater, defrost, control temp change out. Removed existing parts listed. Installed new parts listed. Unit operating as designed."