A mouse chewed through the drain hose. Issues caused by rodents are not covered under the manufacture warranty. ; ordrng 1 WD24X29378 (High loop hose)

Unit oval burner sputters on most at any level. The unit has the right orifice for natural gas and it appears clean.; ordrng 1 WB16X47253 (Oval burner) and 1 WB21X20471 (Valve) and 1 WB28X47138 (Orifice holder)

Door was left open for a while so temps are off. I am ordering an IM and will return to check temps. Customer states the ice cream is usually firm as an indication it is cooling well.; ordrng 1 W11692144 (IM)

"Found inner door liner not sealing on door gasket properly, see pics, ordered inner door liner for unit. Unit does also need ui panel replaced. Did not receive panel part.; ordrng 1 W11637956 (Inner core linner)"

"Gear case is noisy and leaking, ordering gear case , wash plate and slider. Will install suspension on return.; ordrng 1 W10902814 (Wash plate) and 1 W11449841 (Gear case) and 1 W10734521 (Slider)"

"The washer has oil underneath. Capacitor failed. Buzzing during agitation, not moving at all. Oil is all over the components under the unit. 7739830070/ dell; ordrng 1 W11449840 (Gearcase) and 1 W10721967 (CAM) and 1 W11239857 (Belt) and 1 W11395618 (Cap) and 1 W11026785 (Motor) and 1 W11481722 (Actuator) and 1 W11396716 (Suspension)"

"The washer needs an update, did the update. The lock is intermittently not locking. During test the spin was operating with door unlocked. Left rear suspension is failed. Unit need lock, main control and suspension. After update ran test on fill spin and agitate it operates but door remains unlocked. ; ordrng 1 WH22X35757 (Main board) and 1 WH08X32657 (Lock) and 1 WH16X26911 (Left wht rod) and 1 WH16X26910 (Rear right suspension) and 1 WH47X27014 (Dispenser) and 1 WH03X30517 (Shifter) and 1 WH05X24185 (Clutch)"

The putter tub needs to be replaced. The tip for the pressure hose broken off. The gearcase is oily. Bad suspension. The unit is in poor condition. Needs more parts. ; ordrng 1 W11219115 (Outter tub) and 1 W11396716 (Suspension) and 1 W10902814 (Wash plate) and 1 W11449840 (Gearcase) and 1 W10721967 (Cam)

"Installednswitch,test same. Ordered incorrect part ; ordrng 1 WP694419 (Buzzer)"

"JB out 9/26/24Customer states five times in one month the machine did not drain or complete cycle and left water standing in dishwasher sump. Tested fill and drain operation 5 times. Per TSP W11482561B, Ordering replacement drain pump covered under the extended warranty at no charge to the customer extended drain pump is part number W11497943. ; ordrng 1 W11497943 (DRAIN PUMP)"

Found refrigerator not cooling in both compartments compressor relay clicking need this parts.; ordrng 1 5304526183 (Timer) and 1 5304529507 (Relay)

"Broken lint filter, idler arm dragging, noise during operation from idler pulley. ; ordrng 1 WE03X23881 (Lint filter assembly) and 1 WE03X27417 (Idler arm)"

Unit has ice maker that stopped harvesting but kept filling with water. Ice bin frozen solid. Ice tray in ice maker had overflow ice. Ordering new ice maker and valve. ; ordrng 1 W11557001 (Ice maker) and 1 W11535162 (Duel valve)

Small crack on corner of board told cx it would not Affect bored she wants to re-order board. Please check new board when it comes in. Thank you.; ordrng 1 W11620562 (Control elec)

"Found FF top liner light assy out, ordered light assy for unit.; ordrng 1 W11470191 (Top light assy) and 2 W11438525 (Led module)s"

Cx states that unit is making rattling noise After running diagnostic test find that unit has a bad diffuser; ordrng 1 W11175955 (Diffuser)

Found the unit is making a noise and its coming from the damper motor. Opening and closing. Ran test on unit and its even getting stuck a little bit when closing were its allowing a little air come out so it keeps cooling. Little it of the food is frozen also. WPW10479155 damper. ; ordrng 1 WPW10479155 (Damper)

Case14248383. Found oven completely shutting off after 12 minutes need this parts check voltage ok .; ordrng 1 WB27X33412 (Powercontrol) and 1 WB27X33404 (Relayboard)

#87581716Hinge is still popping up when open and closing door called tech line they said to replace hinge and closer at the same time ; ordrng 1 5304524644 (Closer) and 1 5304524637 (Hinge left upper)

Drum is out of round. Unit still shaking violently after leveling. Drum is factory order. Part ordered ; ordrng 1 W11513244 (Inner Basket)

"Ran diagnostics with HQ scanner, locked rotor error. Unit would not spin during spin test.Called tech line tested unit, motor wining checked good, was advised to replace speed sensor correcting issue by; ordrng 1 WH03X32158 (Speed sensor)"

Customer made modification to drain hose took picture. Also tested unit water temp OK water level OK found pump not pushing of water up to the lower wash arm will order parts.; ordrng 1 Wpw10591570 (Pump motor asm) and 1 W10803178 (Lower spray arm) and 1 Wpw10348269 (Pump drain)

Tech was assigned as a helper;

Installed new ice maker water valve working head filter still leading will reorder part filter ok; ordrng 1 W11346623 (Head filter)

Found stackable washer motor exexively loud need motor kit .; ordrng 1 WH49X27319 (Motor)

Found dishwasher not draining power ok need drain pump .; saved tckt

The customer is concerned about out getting burned while using the oven if a rack should fall. The new rack fits the same as the other two. Applied downward pressure on multiple positions I do not see specs on weight limits. Customer locked her shoulder put her weight into a corner by the front RH portion of the rack and forced it to pop under the rail. I dont know what kind of item that is intended to be cooked would create that sort of force so I will need to call WPTS to see how they want me to address this issue.THIS UNIT NEEDS WPTS.; saved tckt

Called techline needs lid lock; ordrng 1 WH08X37937 (Lid lock) and 1 WH03X30517 (Mode shifter)

Leakin sump area. Ordering new sump assembly ; ordrng 1 W11416362 (Sump)

"Needs thermostats , kit; ordrng 1 964P3 (Elment kit) and 1 D504515 (Thermostat)"

F11 error code. Stuck key. Tested UI. And found it pressing the timer and randomly selecting 3s. And turning on the timer. Unable to turn off the timer or get unit to do anything. Ordering UI. Defective and under warranty. ; ordrng 1 5304524332 (UI)

"Control board not working correctly will not take firmware update. Ordering board. Had multiple codes tested unit pump ,heater and fill valve working. ; ordrng 1 WD21X33685 (Main control board)"

"Wire harness broken going to drain pump, , will return with parts.; ordrng 1 W11643701 (Harness)"

Found transmission leaking oil and has bearing noise ordered parts; ordrng 1 W11393685 (Transmission) and 1 W11550891 (Agitator)

Part was not in my parts bin. Messaged SY to let her know. ; schdld next appmnt for 9/18 WED !

"Customer that unit will be needing suspension due to uncontrollable, shaking and noise issue. Customer will wait for parts to come in in order for unit unit to be fixed properly. They stated that they want me to be the one to come back and fix the unit that they only feel comfortable with me coming back.; ordrng 1 W11130359 (Suspenion) and 1 W10752187 (Screw) and 1 W10754161 (Rotor)"

Case#87581897 found refrigerator not powering up door display lights on customer has cacroches called manufacture not covered customer liable for parts and labor complete.; ordrng 1 5304526068 (Ui) and 1 5304526011 (Board)

Found washer exexively loud oil out of gear need this parts.; ordrng 1 W11449840 (Gearcase) and 1 W11550891 (Agitator) and 1 W11481722 (Actuator)

Part came out defective compressor missing rubber fitting also leaked oil out; ordrng 1 W11580057 (Compressor)

"Not cooling, needs compressor ; ordrng 1 5304537795 (Compressor) and 1 5304529285 (Relay)"

"Case#14251451, when pushing filter status Error comes on , was advised by tech line to order filter chip and main control ; ordrng 1 WR55X35485 (Filter chip board) and 1 WR55X40526 (Main control board)"

W11478526The time on the user interface was not working. Unit needs ; ordrng 1 W11478526 (Ui)

Tech was assigned as a helper;

Installed UI and found the control was not needed. Tested with a bake cycle.

Installed parts tested fill wash and drain ok complete.

Installed evap fan test working to spec

"Installed new led light unit is now lighting as designed, cx approved repair and service"

"JB out 9/16/24Customer states oven and broiler fishers do not work. No ignition. Upon arrival tested oven in bake mode. Verified failed of an igniter. Estimate has been approved.Install replacement oven igniter part number W11176454. Tested operation verified bake burner operation and ignition. Reassembled unit and tested operation again with customer. Unit is now as designed, oven and burner heats oven to set temperature in this case of 350°F. Job complete"

Tested found cracked filter housing replaced tested working properly

"The suspension is bottoming out. CX says all washes go off balance. Replaced suspension. Calithe washer, all ops normal."

JB out 9/16/24.Install replacement door gasket part under WD08X23476. Tested dishwasher and allowed to run for eight minutes verifying unit filled with water washes and drain water without leaking any water on the floor. No charge to customer. Job complete.

The housing complex is running on 208VAC. Replaced control board.

Replaced magnetron control and panel tested unit all functions are working per design Job complete

Installed control and thermistor. Noted items on most shelves were pushed to the back. This greatly affects air flow in the unit causing pockets of air to hang in certain areas.

Replace actuator. Tested unit. Unit operating as designed. Job complete.

Replaced broken oven glass. Unit functions as normal.

Diagnosed timer failure. Removed and replaced timer assembly. Tested operation. All OK

Found washer not agitating or washing found actuator clicking Replaced part tested on a fill wash and drain tested ok completepaid thrue I wallet for labor and service per office part covered for 1 year complete.

"On arrival temperature in FF was 24F. Replaced thermistor and diffuser, checked operating to manufacture specs. Job complete."

"Upon arrival, replaced evaporator compressor and a dryer evacuated 5.5 ounces of R1 34A pressure tested unit 150 psi held pressures also held vacuum refilled unit with 5.5 oz of r134a unit I now running as intended advised customer to give at least 24 hours for unit to reach recommended temps job completed"

Replacing part listed. Checked out and ui and main board are responding. Checked out functions on fridge and everything is working as designed. Icemaker should start performing properly now were it should start making more ice. Job completed

"Replaced valve, tested unit working to manufacture spec . Steam is working. Job complete."

Replaced ice maker and inlet water valve. Ice maker now filling with water and working to manufacture specifications. Job complete.

"JB out 9/16/24Verify date of purchase as August 18, 2024 from Lowes. Customer states washing machine does not feel good enough water and the report does not run this site. Tested washing machine is normal. Cycled water setting. Verified water is trickling in from the cold water faucet. Shut off cold and hot water faucets. Removed cold water faucet from back of washer and found a screen Installed a the end of Coldwater hose allowing settlement for water supply to fill and greatly reduce our flow. Removed Coldwater hose from faucet and reverse the direction of hose restriction. Flush cold water through hose remove restriction and reinstall Coldwater hose on washing machine and water faucet. Inspected hot water hose and found no screen and no restriction.Reinstalled hot water hose. Open both hot and cold faucets. Tested washer in normal cycle and verified water flow in the washing machine. Washer is filling designed low water setting. Verified washing machine set for deep water wash is filling with the correct water level. She was also agitating as designed. Cancel cycle and verified proper drain operation. Selected drain and spin cycle. Verified unit properly drains water and spins correctly. Observed cycle end and lid unlocked. Advise customer of one time courtesy no charge on a no defect found service visit as todays service call was generated because of the sediment in the Coldwater hose because the screen was installed backwards. No charge to customer."

Right side gasket was torn and leaking air. Replaced and heat treated. Ice maker was stuck with ice cubes. Removed and cycled. Unit is now working per design.

Internal temp of butter inside ff 47.1 degrees when arrived. Freezer ar 4 degreesInstalled new foam sealer tape to connection areas of reservoir. Found condensation and ice on bottoms section of reservoir. Warm air coming in from tube pathway in cabinet. Causing condensation to form and freeze on reservoir causing line to freeze. Tape in place per techline instructions.

Lid glass separation on right side. Replaced lid. Unit working as intended.

Removed and replaced belt and shifter and tested unit. Unit functions normal now.

"JB out 9/16/24Customer states vegetable crisper drawers do not slide in and out smoothly and hang up. Additionally, the left-hand door is not sealing properly. Removed crisper drawer assemblies, and properly lubricated rollers. Reinstalled drawers and verified smooth operation. Adjusted left-hand and right hand foot break assemblies to properly align freezer door . Unit now operates as designed. No charge to customers. Job complete."

Unit has rumble noise from wheels. Quoted for repair kit install Quote saved in pictures Total paid in full.

Upon arrival found burnt out LED replaced led module unit now lighting as intended job complete

Unit is making a loud noise. Its the fan. No ice buildup and saw a little bit of food near vent in fresh food area. But now unit isnt making the noise anymore and is making ice. No code or any other issues. Checked vent behind crisper drawers and all clear. Then hear ice drop from Icemaker and filled. All checked out. Checked thermistors and all checked out. Job completed

F0e2 code. Found unit was over suds and causing unit to cancel cycle. Ran full diagnostics test and passed. Unit needs to be ran a clean cycle. Found what was put in bleach section of dispenser was to concentrated. Forming to much suds. All passed and checked out. Job completed.

Found refrigerator with temp full capacity couple items in freshfood area overrunning compressor turn back to cold customer to monitor for 72 hours for better results on temp and sound complete.

Cx stated igniter works intermittently. Replaced igniter. Tested unit. Unit operating as designed. Job complete.

Replaced light module I fridge and unit functions as normal.

"Control board shorted, causing sparks and smoke. Acu, console and water valve harness damaged. Pics of damaged components included. Job complete."

Found the inverter had a short in it and was causing the compressor to not turn on. Replaced part listed and unit is now working as designed. Now compressor has heat exchange and is starting to cool.

Upon arrival found frosted under ice bin saw that ice shoot door was not closing all the way replaced it and tested it now is closing all the way advised customer to give us a call back if they have any issues job completed

icemaker failure diagnosed icemaker failure. Removed and replaced icemaker. All OK. Allow 24 hours to stabilize

JB out 9/16/24Customer states washing machine shakes violently and customer has found small black bits of some foreign material underneath the washing machine. Tested washer and drain and midcycle verified unit reaches full speed spin and does not shake. Inspected under washing machine and verified some tiny little black bits of material I have not been able to on a reasonably clean floor. Unable to verify what the black bits are from. Selected quick wash and allow you to fill and agitate. Allowed unit to agitate through entire quick wash cycle advanced to drain and spin. During spin cycle verified cabinet shaking. Adjusted front left hand leveling foot firmly against the floor. Cancel cycle. Tested unit in quick cycle. Verify water fill and agitation. Also verified drain and spin. Unit unit is no longer shaking during spin cycle. No parts needed or used. No charge to customer. Job complete.

Found the ducting was crushed. Rerouted ducting to avoid the gas line and T sharp turns

"F7E3 fault code. Found the cam and belt fried. Replaced both. Unit tested ok.; used 1 W10721967 (Cam), and 1 W11239857 (Belt) from stock"

Found bad valve replaced valve tested unit all functions are working per design job complete

Found small leak on low side line repaired leak pulled vacuum and recharged unit there is good heat exchange and frost pattern job complete

Upon arrival inspected unit customer stated left front burner takes along time to turn on removed burner head and found the smaller ignition orifice clogged was able to remove it and cleaner it unit now lighting as intended job complete

Unit would not run cycle. Found the unit giving a shifter fault code. Found unit with faulty slider. Removed and replaced slider and tested unit. Unit functions normal now; used 1 W10734521 (Slider) from stock

Removed and replaced diffuser and fresh food thermistor. Allow 24 hours to stabilize

Inspected unit as necessary. Ran diagnostics with Smart HQ. Diagnosed error code last five cycles ran were rinse only cycles. Unit will not open up detergent cup during rinse only cycle. Tested operation. Unit was leaking from drain pump. Technician removed and replaced drain pump. All OK

Inspected deli drawers inside ff cabinet and top one was not on the track. Installed correctly but rails on shelving may be defective. Cx is going to use them now that they have been install correctly. Possibly that parts are new and defective. Calibrated the measured fill and showed Cx how to change filters. Job completed.

Checked thermistors with SHQ the temp of product was 42f the customers thermometer by the door read 50f the thermistor read 35f. There was product directly in front of the upper air ducts that may me diverting cold air towards the thermistor tricking the control into thinking it is cold enough in the fridge. Tested unit through SHQ and updated the firmware.showed customer where the thermistor and ducting was for cooling.

Ran diagnostic tests and found unit not spinning. Inspected under unit and found shifter had popped out. Reinstalled and tested again. Unit cold water was only a trickle. Check water valves and cold was almost completely closed opened and water flow is now normal. Unit is now spinning per design. Job completed

Found ice on fan blade caused by poor drainage of the defrost line. Installed probe and unit functions normal now; used 1 819043 (Probe) from stock

E5 fault code which is a faulty ice maker thermistor. Replaced ice maker and verified 120VAC was going to the heater. All checked out ok

"Unresponsive UI panel to the touch UI panel lost communications with ACU, loose wire harness, I reinstalled and secured UI wire harness, unit is now coming on and operating as designed , ran diagnostics unit is ready to go, cx approved repair and service"

F9E1. Inspected coin trap filter on pump. Clogged with hair. Removed front panel to remove debris and unit now passing all tests. Job completed

"Ran diagnostics Long fill error code, also way out of balance inner basket and not completing cycle, on closer inspection found water valve almost on the off position not enough water coming in, took picture of off balance basket. I cleaned out water valve screen, leveled and calibrated, unit is now operating and spinning as designed"

"Electrical issue no power to outlet, checked circuit breaker is not resetting. Advised customer to call an electrician. Job complete."

Checked out ventilation to fresh food to freezer. There was some foam in the vent blocking air. So unit wasnt cooling properly. Cleared out and made sure all vents including damper area wasnt blocked and air flow was good. Left for a bit and unit started to cool a lot better. Set temperatures at recommended temp and checked thermistors. All checked. Job completed

Will replace noisy ice maker; ordrng 1 W11700250 (Ice maker)