Near Nipomo, CA 93444
James
Job Details: 01/03/2020
DISHWASHER KITCHENAID KDPE234GPS0 "Replaced sump assembly, drain pump and wash arm. Unit is now working as intended and customer approves function at this time."
Near Los Angeles, CA 91405
Raymond
Job Details: 01/03/2020
DRYER WHIRLPOOL WGD4815EW2 "Replaced repair kit, motor and wheel. Tested unit. Unit functions as designed."
Near Arroyo Grande, CA 93420
James
Job Details: 01/03/2020
REFRIGERATOR KITCHENAID KRFC704FPS00 Found unit with ice buildup behind evap cover in refrigerator compartment. Unresponsive evap fan in fridge due to ice buildup. Ordering new evap cover assembly; ordrng 1 W11167902 (cover-evap)
Near Nipomo, CA 93444
James
Job Details: 01/03/2020
DISHWASHER JENN-AIR JDB9800CWP2 Installed new racks and heater. Tested unit and found unit to be working as intended at this time.
Near Arroyo Grande, CA 93420
James
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL JFC2089WEM9 Replaced icemaker and water valve. Unit filled icemaker right away. Unit is working as intended and customer approves.
Near Fresno, CA 93722
Jonathan
Job Details: 01/03/2020
MICROWAVE WHIRLPOOL WML55011HS3 Found light bulb bad replaced tested working to spec
Near Fresno, CA 93730
Jonathan
Job Details: 01/03/2020
M/W OTR WHIRLPOOL WMH31017HS0 Found door switch bad replaced tested working to spec
Near Bakersfield, CA 93306
Dane
Job Details: 01/03/2020
OVEN WHIRLPOOL WFG505MOBS3 Upon arrival the oven would not heat. Found the oven igniter was getting 120 V but would not glow. Visually saw a crack in igniter. Unit needs igniter; ordrng 1 W11176454 (IGNITER )
Near Glendale, CA 91214
John
Job Details: 01/03/2020
DRYER MAYTAG MGD6630HW0 "Makes noise and shakes around, there are no feet on the dryer, so it’s sitting on concrete making noise. Need parts.; ordrng 4 3392100 (sub 49621)s"
Near Ontario, CA 91762
Tyler
Job Details: 01/03/2020
WASHER WHIRLPOOL WTW5000DW "Customer stated that the unit not spinning out the clothes. Found unit is off balance. Fixed and tested all,works good at this time."
Near Baldwin Park, CA 91706
Stephen
Job Details: 01/03/2020
WASHER AMANA NTW4516FW3 "Ran diagnostics. Had f8e1 error code. Found cold water not working. Found cold solenoid connector terminal backed out. Reinserted terminal into connector. Ran quick test cycle. Fills, agitates, drains, rinses, and spins properly. Complete."
Near Santa Clarita, CA 91355
Raymond
Job Details: 01/03/2020
OVEN WHIRLPOOL WOD51EC0HS01 Parts sent back and were never pulled when dropped off from return parts. ; ordrng 1 WP4449751 (thrmst-fix)
Near Bakersfield, CA 93306
Dane
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRS588FIHZ Upon arrival there was no Display on the user interface. Removed and replaced control and tested unit. Unit functions normal now
Near Bakersfield, CA 93307
Dane
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRF535SWHV01 Butch... 772671007Upon arrival the unit was building ice on the left side by the rails. I saw a gap on the gasket where it was not ceiling. I open and close the door from the middle of the handle and it sealed correctly. Showed customer how to properly open and close the door so that it seals and does not fall on ice. Call tech line to ensure no other problems on unit. Per tech line unit functions normal
Near Bakersfield, CA 93306
Dane
Job Details: 01/03/2020
REFRIGERATOR MAYTAG MFT2673BEM11 Upon arrival the unit was not making ice. Ran test 56 and got an E2 fault code meaning motor could not harvest. Unit needs new icemaker."
Near Santa Clarita, CA 91354
Raymond
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL KSC23C8EYY02 " Found ice maker blocked with ice cubes and Ice maker continuously cycles due to broken motor auger. Tested and ice maker sized after 3 cycles and would not fill. Needs parts."
Near Santa Clarita, CA 91354
Raymond
Job Details: 01/03/2020
REFRIGERATOR KITCHEN AID KRMF706ESS01 Upon arrival cx states upper lights flash and unit randomly shuts down and reboots itself. Needs controls and led module.; rqstng P&A on 1 W10804160 (cntrl-elec) and 1 W11205082 (module) and 1 W11330971 (CONTROL) and 1 WPW10624574 (cntrl-elec) and 1 WPW10675033 (cntrl-elec) and 1 WPW10769076 (cntrl-elec)
Near Fontana, CA 92336
Kevin
Job Details: 01/03/2020
RESIDENTIAL REFR WHIRLPOOL WRF954CIHZ00 Freezer door handle came loose. I removed door handle and found mounting bolt under door handle had backed out and caused handle screw to come loose. I tightened bolt and reinstalled handle. All tests good.
Near Riverside, CA 92508
Kevin
Job Details: 01/03/2020
REFRIGERATOR KITCHENAID KSSC42QTS03 Customer concerned with hum from compressor. Temps are 37 in RC and 0 in FC. Temps are perfect. Instructed customer that the hum from the compressor is normal and if temps are good then compressor is working normally.
Near San Gabriel, CA 91776
Francisco
Job Details: 01/03/2020
RESIDENTIAL REFR WHIRLPOOL WRF560SEYM05 Checked unit found frost build up all over fc. Removed door, dissembled unit, and found glides miss aligned. Used steam gun to remove all frost and ice build up. Aligned glides or slides back re assembled unit also heat treated gasket for proper closure. Unit now working properly.
Near Fresno, CA 93728
Jonathan
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRS325SDHV01 Found start dev bad replaced tested working to spec
Near South Pasadena, CA 91030
Francisco
Job Details: 01/03/2020
DISHWASHER KITCHENAID KDFE104HPS0 "Checked unit found right side hinge off it’s pin and impeding door from closing, pulled DW out a bit. Reset hinge on pin unit working as intended. "
Near Bakersfield, CA 93311
Dane
Job Details: 01/03/2020
DRYER MAYTAG MGDB765FW0 Upon arrival found the unit short cycling. Found the burner coils out of range. Removed and replaced coils and tested unit. Unit functions normal now
Near Pasadena, CA 91107
Francisco
Job Details: 01/03/2020
WASHER WHIRLPOOL MAV8757AWW Checked unit found belt slipping on pulley and pump making grinding noise. Removed and replaced belt and pump. Unit now checks ok
Near Simi Valley, CA 93063
Aaron
Job Details: 01/03/2020
DISHWASHER WHIRLPOOL WDT730PAHZ0 "Checked the unit, found the unit in a continuous drain , not filling , checked under the dishwasher, customers harness damaged. Cannot do more work on unit due to circumstance of damage ."
Near Simi Valley, CA 93065
Aaron
Job Details: 01/03/2020
RANGE WHIRLPOOL RANGE "Customer declined service at the door"
Near Fillmore, CA 93015
Aaron
Job Details: 01/03/2020
RANGE KITCHENAID KFGG500EBS2 Replaced the 2 front orifices and holders, which are the power burners, unit is working as designed.
Near Moreno Valley, CA 92551
Kevin
Job Details: 01/03/2020
DRYER WHIRLPOOL WGD4815EW2 Timer not advancing in any cycle. I tested unit and found voltage to timer motor but motor not turning. Failed timer. Removed and replaced timer. Tested unit. All tests good.
Near San Fernando, CA 91340
Raymond
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRB322DMBW00 Replaced control and harness. Programmed control. Unit functions as designed.
Near San Bernardino, CA 92407
Tyler
Job Details: 01/03/2020
WASHER MAYTAG MVWB965HW0 Customer stated that washer machine is leaving streaks on his dark loads. Cycle tested unit and calibrate it all works good at this time customer to start to try and use less soap and possibly change detergents. All works good this time.
Near Moreno Valley, CA 92553
Kevin
Job Details: 01/03/2020
WASHER WHIRLPOOL WGD4815EW2 Unit making noise during cycle. I disassembled unit and found failed drum rollers and idler pulley causing noise. Removed and replaced rollers and idler pulley. Tested unit. All tests good
Near Santa Maria, CA 93455
James
Job Details: 01/03/2020
WASHER WHIRLPOOL MHW8200FW0 "Customer stated unit now working correctly, not spinning clothes out leaving them wet at end of cycle. Inspected unit and found over soaping conditions. Cleared out soap, recalibrated unit and tested. Unit completed testing with. No problems detected. Unit is now working as intended. Instructed customer on soap concentration settings. Adjusted from 6x concentrate to 2x . Unit is working as intended."
Near Bakersfield, CA 93314
Dane
Job Details: 01/03/2020
REFRIGERATOR BO KITCHEN AID KRMF706ESS Removed and replaced control boards and tested unit. Unit functions normal now
Near Rancho Cucamonga, CA 91730
Tyler
Job Details: 01/03/2020
DRYER WHIRLPOOL WGD5620HW0 Customer stated that now the dryer doesn’t even turn on. Removed and replaced main control and console tested all works good at this time.
Near Los Angeles, CA 90272
Isidore
Job Details: 01/03/2020
WASHER MAYTAG MHW5100DW0 "Removed old bellows and installed new washer bellows, test for leaks and operation, ok at this time."
Near Bakersfield, CA 93312
Jim
Job Details: 01/03/2020
MICROWAVE JENN-AIR UMC5200BAS Power to the control board but no power out. Bad board. W10261245 is the part number for the board. The board is discontinued.
Near Los Angeles, CA 90272
Isidore
Job Details: 01/03/2020
WASHER WHIRLPOOL WFW6620HC0 "Removed top and rear panels, old control board. Installed new washer control board test washer operation ok at this time reinstalled panels washer working at this time."
Near Alhambra, CA 91801
Stephen
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRT111SFDW04 Replaced evaporator fan blade. Installed spacer washers for FC and RC doors. Heat treated door gaskets. Advised customer to leave doors closed for 5 hours before opening. Unit is cooling properly at this time. Complete.
Near Topanga, CA 90290
Isidore
Job Details: 01/03/2020
DISHWASHER KITCHENAID KDPM354GPS0 "Found dishwasher not cycle water removed outer door panel, old wash motor assembly, installed new dishwasher motor assembly, test for leaks and operation, dishwasher working at this time"
Near Arcadia, CA 91006
Francisco
Job Details: 01/03/2020
OVEN WHIRLPOOL RBS245PRS06 "Removed and replaced control board, tested ops unit checks ok. "
Near Victorville, CA 92395
Cesar
Job Details: 01/03/2020
DRYER WHIRLPOOL MGDB835DW4 Customer instruct on function and loading
Near Baldwin Park, CA 91706
Stephen
Job Details: 01/03/2020
WASHER MAYTAG MVWX655DW1 "Ran diagnostics. Had f7e1 error code. Cleared error code.No spinning per customer. Found capacitor connector terminal backed out. Reinserted terminal into connector. Ran auto test cycle. Fills, agitates, drains, rinses, and spins properly. Complete."
Near Victorville, CA 92392
Cesar
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRX735SDBM00 Lady company did not install new ice maker correctly found ground wires not connected and main harness connector not fully seated causing ice maker not to cycle corrected install and tested ice maker it filled with water all checked good
Near Hesperia, CA 92345
Cesar
Job Details: 01/03/2020
DISHWASHER AMANA ADB1400AGW1 Found failed drain pump has power will not cycle not draining water out replaced drain pump tested unit all checked good
Near Paso Robles, CA 93446
Tom
Job Details: 01/03/2020
RANGE JENN-AIR JDS1450DS0 "Entered diagnostics, found error code F8E0, voltage check at Fan Motor connector shows 120VAC when activated in diagnostics, Cooling Fan needs to be replaced. Installed Cooling Fan, tested fan, checked okay, good rotation. No damage to unit or home from tech, job complete."
Near Templeton, CA 93465
Tom
Job Details: 01/03/2020
WASHER WHIRLPOOL MVWB766FW1 "Installed Control Board and Console, ran diagnostic tests, no error codes, check okay. No damage to unit or home from tech, job complete."
Near Paso Robles, CA 93446
Tom
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRF560SMYH04 "Installed IM, ran Harvest Cycle, check okay. No damage to unit or home from tech, job complete."
Near Atascadero, CA 93422
Tom
Job Details: 01/03/2020
DISHWASHER KITCHENAID KDTE234GPS0 "Entered diagnostics, found no error codes, ran diagnostic tests, no error codes found, all components functional. Customer instruct, requires sanitation capability, customer instruct."
Near Apple Valley, CA 92307
Cesar
Job Details: 01/03/2020
DRYER MAYTAG MGDB835DW4
Near Camarillo, CA 93010
Joe
Job Details: 01/03/2020
DRYER MAYTAG MGDB835DW4 Unit will not dry clothes. On Inspection found unit will not dry clothes due to the heating coils being unplugged. After installing harness to heating coils unit began to function as designed. Job complete.
Near Los Angeles, CA 91343
Raymond
Job Details: 01/03/2020
WASHER AMANA NTW4605EW0 "Upon arrival cx states unit shuts down mid cycle. Control not responding to service diagnostic. Unit bouncing due to weak springs. Need control, suspension agitator.; ordrng 1 W10780045 (suspension) and 1 W10908289 (agitator)"
Near Visalia, CA 93292
Enrique
Job Details: 01/03/2020
REFRIGERATOR KITCHENAID KRMF706EBS01 "Inspected kitchen aid refrigerator . Leaking from ice box and drain tube . Also need door gasket , black color not available . Customer ok with grey .; ordrng 1 W10846057 (gasket-fip) and 1 W11084807 (extension) and 1 WPW10280988 (gasket) and 1 WPW10320706 (gasket) and 1 WPW10392172 (gasket)"
Near West Covina, CA 91790
Stephen
Job Details: 01/03/2020
WASHER MAYTAG MVWC200BW1 "Ran diagnostics. Had f8e1 error code. Cleared error code. Found noisy( worn ) drain pump, worn gear case bearings, splutch, belt, agitator, shifter.Water leaked onto capacitor. Needs parts listed: 1 285565 (agitator assy,comp) and 1 W10721967 (drive pulley) and 1 W10772621 (screw) and 1 W11158830 (CAPACITOR ) and 1 W11255272 (GEARCASE) and 1 WPW10006384 (drive belt)"
Near Pomona, CA 91767
Stephen
Job Details: 01/03/2020
RANGE - GAS WHIRLPOOL WFG550S0HZ1 Found RF burner head stained. Needs RF burner head; 1 WPW10515455 (burnr-head)
Near Hanford, CA 93230
Enrique
Job Details: 01/03/2020
WASHER MAYTAG MVWB765FC1 Inspected Maytag washer;; unit makes very loud noise during spin cycle . Needs gearcase and rotor; ordrng 1 W10754161 (motor rotor) and 1 W10811956 (drum assy)
Near San Dimas, CA 91773
Stephen
Job Details: 01/03/2020
STEAM DRYER MAYTAG MCG8000AWW "Drum not turning, noisy. Found broken belt, worn idler, rollers, blower wheel.Needs parts: 1 31001317 (wheel,blower) and 1 341241 (belt,drive) and 1 LA-1008 (roller kit rear) and 1 WP31001710 (idler arm)"
Near Lompoc, CA 93436
James
Job Details: 01/03/2020
WASHER MAYTAG MVWB835DW3 "Found unit not draining, filling with hot water, and registering stuck key. Tried to activate manual testing. Would not fill with hot water. Water solinoid not opening. Ordering new drain pump, water inlet, console. Will return when parts arrive. ; ordrng 1 W10876600 (drain pump) and 1 W11112656 (console) and 1 W11172234 (housing)"
Near Riverside, CA 92509
Kevin
Job Details: 01/03/2020
KITCHEN WHIRLPOOL WDT730PAHZ0 Unit giving f2e2 and will not start cycle. I verified proper polarity and voltage. Communication issue between main control and user interface. Ordering parts.; ordrng 1 W11305308 (cntrl-elec) and 1 W11368911 (CNTRL-ELEC)
Near Rialto, CA 92376
Kevin
Job Details: 01/03/2020
WASHER MAYTAG MHW5630HC0 Unit leaking during cycle. I found ripped door boot not allowing water to stay inside drum during cycle. Ordering door boot. ; ordrng 1 W11314648 (bellow)
Near Rialto, CA 92376
Kevin
Job Details: 01/03/2020
WASHER AMANA NTW4516FW3 Unit making noise in spin cycle. I found belt slipping on pulley when drum has weight. Failed belt and cam kit. Ordering parts. ; ordrng 1 W10721967 (drive pulley) and 1 W11239857 (belt)
Near Santa Maria, CA 93455
James
Job Details: 01/03/2020
WASHER MAYTAG MVWB835DC2 Found unit with off balance errors and long drain error. Ran auto test and found drain very slow due to drain pump barely running. Ordering new drain pump; ordrng 1 W10876600 (drain pump)
Near Bakersfield, CA 93309
Dane
Job Details: 01/03/2020
WASHER WHIRLPOOL WFW97HEDBD0 On arrival unit will not spin the clothes dry and will give an F3E1 fault code. Found service pointer on this issue stating to check the air trap. Found air trap blocked. Unit needs new trap; rqstng P&A on 1 W10626116 (trap)
Near Ontario, CA 91762
Tyler
Job Details: 01/03/2020
DRYER WHIRLPOOL WGD4815EW2 Customer stated that the drum is making noise found the drum seal is coming off. Ordering drum in stock.; ordrng 1 W10899578 (drum)
Near Frazier Park, CA 93225
Jim
Job Details: 01/03/2020
WASHER WHIRLPOOL WFC7500VW2 Appointment reschedueld,.
Near Perris, CA 92571
Kevin
Job Details: 01/03/2020
DRYER WHIRLPOOL WGD7500GC0 Dryer is not hooked up- unable to diagnose unit without gas. Rescheduling call. ; schdld next appmnt for 1/4 SAT !
Near Rosemead, CA 91770
Stephen
Job Details: 01/03/2020
WASHER WHIRLPOOL WTW4816FW2 "Ran diagnostics. No error codes. Tested spin. Found worn gear case spin bearings. Needs gear case, splutch,belt, agitator, shifter. Needs parts listed ordered: 1 W10772621 (screw) and 1 W11255272 (GEARCASE) and 1 WP3951744 (agitator) and 1 WPW10006384 (drive belt)"
Near Phelan, CA 92371
Cesar
Job Details: 01/03/2020
WASHER WHIRLPOOL WTW5000DW2 Failed shifter not able to find position rerouted for shifter ; ordrng 1 W10913953 (actuator)
Near Los Angeles, CA 91344
Raymond
Job Details: 01/03/2020
WASHER WHIRLPOOL GSX9885JT0 Found failed drum support rubber wheel was not round making drum bounce during operation. replace supports unit tested good
Near Camarillo, CA 93010
Joe
Job Details: 01/03/2020
WASHER MAYTAG MVWB835DW4 Units control is being blown by the ui. Ordering parts.; ordrng 1 W11112656 (console) and 1 W11170706 (cntrl-elec)
Near Bakersfield, CA 93314
Jim
Job Details: 01/03/2020
DISHWASHER WHIRLPOOL WDT970SAHZ0 It seems as if the spray arm is the issue; ordrng 1 W10629546 (arm-spray)
Near Shandon, CA 93461
Tom
Job Details: 01/03/2020
WASHER MAYTAG MVWB765FW3 "Entered diagnostics, found error codes F8E6, F9E1, F2E1. Found Drain Pump failure, found Water Inlet Valve failure, order Water Valve.Water Valve - (W11165546); ordrng 1 W11165546 (VALVE)"
Near Bakersfield, CA 93312
Jim
Job Details: 01/03/2020
WASHER MAYTAG MVWB765FW1 Found no surface area that is grinding. The noise only occurs when it is agitating in the clockwise direction. All indicators point to a bad transmission.; need to order 1 W10811956 (drum assy).
Near Los Angeles, CA 91364
Isidore
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRT111SFDM03 "Found compressor starting then shutting down , ordering compressor WPW10507886 and dryer W10843121. Send sealed system tech Allow 2 hours ; ordrng 1 W10843121 (filter dryer) and 1 WPW10507886 (compressor)"
Near Bakersfield, CA 93306
Andrew
Job Details: 01/03/2020
WASHER MAYTAG MVWB835DW4 Unit has shorted control and lid lock. Replaced lid lock and control and no response from console. Power to console but will not power up. Needs console. ; ordrng 1 W11112656 (console)
Near Bakersfield, CA 93307
Andrew
Job Details: 01/03/2020
MICROWAVE WHIRLPOOL KEMC308KSS01 Checked unit and it has a door fault on the display for microwave. It has faulty microswitch. Ordering all three microswitches for unit and as well as the LED light which is out in the cavity.; ordrng 3 W10211972 (switch)s and 1 WPW10440740 (lmp-basles)
Near Stevenson Ranch, CA 91381
Raymond
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRS588FIHZ00 "Replaced door, sealed cabinets with adheasive. Cx states food freezes in RC section.Schdld next appmnt for 12/30 MON !"
Near Bakersfield, CA 93307
Andrew
Job Details: 01/03/2020
DISHWASHER WHIRLPOOL WDTA50SAHZ0 Need to reschedule upon arrival of parts.
Near Tulare, CA 93274
Enrique
Job Details: 01/03/2020
REFRIGERATOR WHIRLPOOL WRS588FIHV00 "Installed new door , removed protective film . Door came in defective. Reordering the door .; ordrng 1 LW11038917 (dor-fip)"
Near Lathrop, CA 95330
William
Job Details: 12/16/2019
DRYER WHIRLPOOL WED6620HC0 Installed screw in exhaust duct at back of dryer to stop vibration sounds with cx.
Near Manteca, CA 95336
William
Job Details: 12/16/2019
REFRIGERATOR WHIRLPOOL WRS315SDHZ02 "Found defrost drain tube backed out of liner grommet, reinstalled defrost drain tube with adhesive. Tested drain function , tested ok"
Near Manteca, CA 95336
William
Job Details: 12/16/2019
DISHWASHER KITCHENAID KDTE334GPS0 "64, 84, 44, replaced main control, ran self diagnostic cycle, unit operating as designed."
Near Modesto, CA 95358
William
Job Details: 12/16/2019
WASHER WHIRLPOOL WTW5000DW1 "Found code for latch error, Replaced washplate, cap & latch, ran diagnostics cycle, tested ok"
Near Lathrop, CA 95330
William
Job Details: 12/16/2019
DISHWASHER WHIRLPOOL WDT710PAHZ1 "Found arch fault breaker pop, reset breaker, checked for high current draw, instructed cx on power issues with unit, ran self diagnostic cycle, unit operating as designed"
Near San Bernardino, CA 92411
Tyler
Job Details: 12/16/2019
OVEN WHIRLPOOL WFG525SOHZ1 Customer stated that the unit had a F1E 0 error code for internal control error. Removed and replaced main control tested all works good at this time.
Near Bloomington, CA 92316
Tyler
Job Details: 12/16/2019
WASHER MAYTAG MVWB765FW3 "Customer stated that the unit is not making noise when cycle is started or stopped. Found sound turned off. Fixed and calibrated unit, no error codes, tested unit , all works good at this time."
Near Rialto, CA 92376
Tyler
Job Details: 12/16/2019
OVEN WHIRLPOOL WGG745S0FS02 Customer stated that after a power outage the lower oven locked and would not unlock. When self diagnostic test on oven to test the latch now latches unlocked tested oven all works good at this time.
Near Upland, CA 91784
Tyler
Job Details: 12/16/2019
MICROWAVE WHIRLPOOL WOC75EC0HS01 Customer stated that the microwave door if closed softly has to be pushed to activate the the switch. Documented for customer no fix for this at this time.
Near Upland, CA 91784
Tyler
Job Details: 12/16/2019
OVEN KITCHENAID KODC304ESS00 Customer stated that lower oven stopped working after a self clean. Removed and replaced thermostat tested all works good at this time.
Near Fontana, CA 92337
Tyler
Job Details: 12/16/2019
REFRIGERATOR WHIRLPOOL WRS325SDHZ Customer stated that the u it has frost. Found door seal not making contact with cabinet. Heat treated door seal tested all works good at this time.
Near Fontana, CA 92335
Tyler
Job Details: 12/16/2019
REFRIGERATOR WHIRLPOOL WRF535SMBM Customer stated that the unit stopped cooling. Found ice buildup around fan customer to defrost. Removed and replaced right refer door seal. All works good at this time.
Near , CA 93636
Timothy
Job Details: 12/16/2019
DISHWASHER FRIGIDAIRE FFCD2413US "Installed parts. Tested unit. Unit operating as designed, no leaks noted."
Near Fresno, CA 93710
Timothy
Job Details: 12/16/2019
REFRIGERATOR WHIRLPOOL WRS588FIHV Installed control. Unit operating as designed.
Near Clovis, CA 93611
Timothy
Job Details: 12/16/2019
RANGE WHIRLPOOL WFC310S0EW3 Installed hinges . Tested unit. Door closing normally.
Near Covina, CA 91724
Stephen
Job Details: 12/16/2019
WASHER MAYTAG MVWX655DW1 "Replaced gear case, splutch,belt, hub, & screw. Ran calibration, auto test cycle. Fills, agitates, drains, rinses,dispenses, and spins properly. Complete."
Near Temple City, CA 91780
Stephen
Job Details: 12/16/2019
DISHWASHER WHIRLPOOL WDT970SAHZ0 "Replaced tub assembly, link kit, door hinges. DW is in garage ( not installed yet ). Unable to test DW. Not responsible for leaks. Complete."
Near Covina, CA 91722
Stephen
Job Details: 12/16/2019
WASHER WHIRLPOOL WFW5620HW0 "Ran diagnostics. Had f5e2 error code. Cleared error code. Ran quick test cycle. Fills, washes, drains, rinses,dispenses, locks/ unlocks, & spins properly. Instructed customer NOT to wash mixed loads( wash like items). Possible unbalanced loads. Complete."
Near Manteca, CA 95336
William
Job Details: 12/16/2019
REFIRGERATOR WHIRLPOOL WRF535SWHV00 Round right French door gasket pulling apart at the bottom ordered right door gasket for unit.; ordrng 1 W11368721 (DOOR GASKET)
Near Pasadena, CA 91101
Stephen
Job Details: 12/16/2019
WASHER/COMMERCIA MAYTAG MVWP575GW0 "Ran diagnostics. No error codes found . Ran rinse and spin with load. Fills, agitates, drains, rinses, and spins properly. Instructed customer on unbalanced loads, washing mixed loads.Complete."
Near Duarte, CA 91010
Stephen
Job Details: 12/16/2019
WASHER MAYTAG MVWX655DW2 "Ran diagnostics. Had f0e5, f0e2 error codes. Cleared error codes. Ran calibration, auto test cycle. Fills, agitates, drains, rinses, dispenses, & spins properly. Instructed customer on unbalanced loads and detergent usage( too much detergent). Complete."
Near Yucaipa, CA 92399
Rod
Job Details: 12/16/2019
REFRIGERATOR KITCHENAID KRFF707ESS01 Disp fill measurement stalls on 5-7 cups If +/- increment selection is held for 10sec’s or more the display will stop increasing explained to consumer proper operation of user interface.Had had two different techs tell them that “they had to just live with it.”Owners guide explains the above operation of user interface