We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Oxnard, California 93033
Ian Y
Job Details:
10/29/2024
"Found unit full of water. Tilted unit back and adjusted wire harness. Unit instantly drained. With the harness in a position where it was connected to pump I tried to start a drain and spin and unit attempted to lid lock 4 times and wouldnt. Ordering lid lock, harness and control. ; ordrng 1 W11368616 (Lid lock) and 1 W11491433 (Control) and 1 W11335100 (Harness)"
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GSS25IYNZHFS
Near Bakersfield, California 93307
Joe P
Job Details:
10/29/2024
"No show, called office 3 times no answer. Took pictures of house waited 15 minutes and left. Called the office again and talked to Silvia she called customer, we have the wrong number for customer. ; saved tckt"
We serviced a
GENERAL ELECTRIC RANGE
Model PGS930YP8FS
Near Ventura, California 93003
Ian Y
Job Details:
10/29/2024
Found units back left burner extinguishing flame on low setting. Ordering new burner. ; ordrng 1 WB16X24721 (Burner small)
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC604FSS01
Near Tracy, California 95376
William
Job Details:
10/29/2024
"Sr #7740145611, checked operating pressure in test #40, found high side pressure 210 psi, low side in -10 vac, sealed system restricted, called WP tech line. Ran sealed system equalization test , sealed system not equalizing pressure.Tech line designated unit as unrepairable. Instructed cx to call warranty co. With sr# 7740145611, took pic for tech line.; ordrng 1 W11291123 (FF evap assy)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Bakersfield, California 93307
Brandon
Job Details:
10/29/2024
Tech was assigned as a helper;
We serviced a
CROSLEY N/A
Model CAW9244BW0
Near Oakdale, California 95361
Martin
Job Details:
10/29/2024
Found bad suspension ordering new ; ordrng 1 W10780048 (Suspension)
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Riverside, California 92509
Robert U.
Job Details:
10/29/2024
Found the unit had two error codes stored. Most recent being the f4e3 wash motor not running. And indeed it is now. It is receiving the right voltage. The second error code is f7e1 and that is a heating issue. The element is not within range but it does come on. Will replace heater and control for that. Ordering sump and motor assembly. ; ordrng 1 W11613479 (Pump and motor)
We serviced a
JENN-AIR WINE FRIDGE
Model n/a
Near Nipomo, California 93444
Jack
Job Details:
10/29/2024
Customer showed me seal. Top shelf wasnt opening properly. Found hinge was not on correctly. Shelf was rubbing the seal and damaged it. New seal needed. Seal WPW10624183. ; ordrng 1 WPW10624183 (Seal)
We serviced a
WHIRLPOOL DRYER
Model WGD8620HW3
Near Bakersfield, California 93308
Joe P
Job Details:
10/29/2024
"Installed drum, checked unit operating to manufacture specs."
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD708MPS00
Near Bakersfield, California 93312
Brandon
Job Details:
10/29/2024
Installed new control. All issues have now been resolved.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Morro Bay, California 93442
Leo
Job Details:
10/29/2024
"Upon arrival, replaced deli drawer UI, it showed signs of moisture, tested all steps of ice maker system, all passed and unit should resume ice production,Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Moreno Valley, California 92555
Kevin
Job Details:
10/29/2024
Removed and replaced main control. I calibrated new control in diagnostic and tested unit on normal cycle. All tests good.
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Riverside, California 92503
Robert U.
Job Details:
10/29/2024
Fo7nd after replacing the main control and the latch assembly the unit is now operating properly I recalibrated the new control and ran a diagnostic cycle. All functions restored. Job completed.
We serviced a
GE REFRIGERATOR
Model CFE29TSDCSS
Near Bakersfield, California 93306
James
Job Details:
10/29/2024
$115.99 CK Auth# L94PV9Installed mullian and collected remaining balance.
We serviced a
GENERAL ELECTRIC RANGE
Model C2950P2M2S1
Near San Luis Obispo, California 93401
Jack
Job Details:
10/29/2024
"Replacing door thats damaged, replaced and now lower door is now functional to us. Sealing properly and unit is been tested. Job completed"
We serviced a
GENERAL ELECTRIC REFRGERATOR
Model GSS25GGPBCBB
Near Riverside, California 92507
Robert U.
Job Details:
10/29/2024
After replacing all parts ordered the lights in the freezer work and the refrigerator as well. Also dispensing ice when asked. All functions restored. Job completed.
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Merced, California 95340
Cruz
Job Details:
10/29/2024
Fixed- installed new part (belt) calibration test pass- auto test pass- no screeching noise- cx ok repair
We serviced a
KITCHENAID DOUBLE RANGE
Model KFED500ESS05
Near Bakersfield, California 93304
James
Job Details:
10/29/2024
Replaced components and tested unit. Unit now heats as intended.
We serviced a
WHIRLPOOL FREEZER
Model WRX986SIHZ00
Near Redlands, California 92373
Francisco
Job Details:
10/29/2024
Removed and replaced ui asked Cx to monitor ops.
We serviced a
WHIRLPOOL MW OVEN COMBO
Model WOC54EC7HB01
Near Upland, California 91784
Javier V
Job Details:
10/29/2024
"Job complete install part necessary. I made sure that I turned off the breaker to the house before installing part after sign it turned on all power, and made sure that the unit work which it did everything is working spec."
We serviced a
WHIRLPOOL REFRIGERATOR
Model MFI2570FEZ08
Near Hilmar, California 95324
Cruz
Job Details:
10/29/2024
"Fixed- installed new parts (motor, York, divider) unit is now dispensing ice cube- cx ok repair"
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Pasadena, California 91103
Stephen
Job Details:
10/29/2024
"Ran diagnostics. Had f5e3, f9e1, f0e2 error codes. Cleared error codes. Found drain pump harness connector not seated. Reseated harness connector. Cleaned filter. Unable to completely test unit due to being not connected to drain or water. Drain & spin, door lock are working properly at this time. Complete."
We serviced a
JENN-AIR COOKTOP
Model JGD3536GB05
Near Los Angeles, California 91344
Paul
Job Details:
10/29/2024
Replaced burner head with new ones. Unit is now working properly. New ones are a different material and color.
We serviced a
WHIRLPOOL RANGE
Model WOS31ES0JS01
Near Victorville, California 92394
Cesar
Job Details:
10/29/2024
Replaced UI and control tested unit all checked good
We serviced a
WHIRLPOOL WASHER
Model MVW5035MW1
Near Moreno Valley, California 92555
Kevin
Job Details:
10/29/2024
"Removed and replaced main control, valve and switch. Tested unit. All tests good."
We serviced a
FRIGIDAIRE RANGE
Model FCFE3083ASA
Near Reedley, California 93654
J.E.
Job Details:
10/29/2024
Installed new infinite switch and retested unit now working as designed job completed
We serviced a
SPEED QUEEN WASHER
Model AWNE9RSN116PW01
Near Taft, California 93268
Raymond
Job Details:
10/29/2024
"LD error, lid switch not engaging lid arm properly, secured arm and fixed travel of arm and tested unit functioning as designed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Lancaster, California 93536
Jonathan B.
Job Details:
10/29/2024
"JB OUT 10/29/24 Upon arrival found all foods in freezer compartment frozen solid. Compressor replacement is not necessary. Removed all foods and shelving baskets from freezer compartment installed replacement evaporator fan motor harness part number W11578030 as ordered. Tested fan operation now operating properly. Reassembled freezer compartment reinstalled freezer drawer door tested operation again with customer verified cold air is now being delivered into the fresh food section. Compressor , control, electric and evaporator have been returned as not needed. No charge to customer. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near New Cuyama, California 93254
Raymond
Job Details:
10/29/2024
"7740212853 Unit installed on sloped foundation, with only 1 supply line connected and drain hose being drained on the ground causing siphon. This is causing unit to abort cycles. U it passed field service cycle and is now functioning as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Riverside, California 92508
Robert U.
Job Details:
10/29/2024
I replaced the evap motor and the harness that has the defrost bi metal in it. I also replaced the user interface and main control for the not turning on after defrost. It will take 24 to 48 hours for temps to Normalize. Job completed.
We serviced a
JENN-AIR ICEMAKER
Model JF42NXFXDE00
Near Los Angeles, California 90049
Tim B
Job Details:
10/29/2024
"Replaced led lights and unit functions as normal. Cx refused gaskets. Called crystal, Cx paid enough,job done."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Santa Ynez, California 93460
Kash S
Job Details:
10/29/2024
"Replaced rotor, stator, slider and, control board, verified with cx that unit is starting cycle and operating at normal noise levels during spin, cx has no further questions/concerns, unit is fully operational at this time"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Los Angeles, California 91306
Samson
Job Details:
10/29/2024
"Replaced bad control board and shifter, unit test ok. Complete"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHT2045VW2
Near Bakersfield, California 93304
Raymond
Job Details:
10/29/2024
"Tech meant to use filter dryer, drier installed last visit. Contacted cx to make sure unit still cooling unit operating as designed."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Thousand Oaks, California 91360
Felipe S
Job Details:
10/29/2024
"Remove old compressor and drier. Install the new seal system components on the unit and harness. Pressurize the system with nitrogen at 240 psi, no leaks found at this time. Vacuum the unit and unit holds the vacuum. Recharge the system with 55 grams of refrigerant R600a. Retest the system and the pressure with the unit running are, -5.3 and 62.4. This unit starts to cooling down, inform the customer they need wait at least 24 hours, for proper cooling. Job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Redlands, California 92374
Francisco
Job Details:
10/29/2024
"Checked u it found torn gasket, removed and replaced gaskets unit now working properly. No damage by tech."
We serviced a
KITCHEN AID REFRIGERATOR
Model KBSD608ESS01
Near Los Angeles, California 91352
Samson
Job Details:
10/29/2024
"7740217440- Matt, unit need only reset from te panel, called tech support and advise cx to use for a while as all checked good. Complete"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Bakersfield, California 93314
Brandon
Job Details:
10/29/2024
"Installed new harness, capacitor, and actuator. Unit is now able to run cycles to completion."
We serviced a
KITCHEN AID MW OVEN COMBO
Model KOEC530PSS00
Near Simi Valley, California 93065
Paul
Job Details:
10/29/2024
"Unit had a bad light inside of microwave, replaced harness and light bulb. Harness was broken and looked like it caused a short. After repair unit is working properly."
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Apple Valley, California 92307
Cesar
Job Details:
10/29/2024
Replaced sensor all tested good
We serviced a
GENERAL ELECTRIC WASHER
Model GTW335ASN2WW
Near Victorville, California 92392
Cesar
Job Details:
10/29/2024
Replaced failed parts all tested good
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Los Angeles, California 91326
Ian Y
Job Details:
10/29/2024
Replaced missing end caps on units top rack. Top rack no longer sliding all the way out. Job complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW01
Near Los Angeles, California 91356
Alejandro
Job Details:
10/29/2024
"Found the unit not cooling, verify the problem,compressor not running, replace compressor,service valve,drier,relay and capacitor, charge nitrogen,not verify leaks, make a vacuum charge refrigerant 4.9 oz R134a check compressor condenser and evaporator fan motors unit start work properly"
We serviced a
JENN-AIR DOUBLE OVEN
Model JJW3830LM01
Near Los Angeles, California 90049
Tim B
Job Details:
10/29/2024
Replaced broken glass door. Unit functions as normal.
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Dinuba, California 93618
J.E.
Job Details:
10/29/2024
Cycled unit and found mice infested causing damage to control board. Main harness and lid lock harness took pics and notified square trade. Not covered. Job completed
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323AW7
Near Bakersfield, California 93308
James
Job Details:
10/29/2024
"Removed and replaced made, manifold and water lines. Unit now working as intended with no more leaks."
We serviced a
KITCHENAID ICEMAKER
Model KUIX535HPA01
Near Santa Clarita, California 91321
Felipe S
Job Details:
10/29/2024
Install the new grill cutter on the unit. Retest the unit and now is working properly. Job complete
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Glendale, California 91207
Oscar
Job Details:
10/29/2024
"After completing the replacement of previously diagnosed parts and components, a functional test was successfully conducted."
We serviced a
BOSCH DISHWASHER
Model dwhd770w
Near Bakersfield, California 93311
Randy
Job Details:
10/29/2024
Removed and replaced cord. Tested now working as designed
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814TW
Near Rosamond, California 93560
Jonathan
Job Details:
10/29/2024
"Installed new washers, tested unit and is working properly."
We serviced a
WHIRLPOOL COOKTOP
Model KCGS556ESS05
Near Los Angeles, California 91304
Sean W
Job Details:
10/29/2024
Wire for front right burner to spark module not making good contact.reconnected wire to spark module.cooktop now working properly.
We serviced a
ZLINE RANGE - ELECTRIC
Model SGR30
Near Los Angeles, California 91352
Samson
Job Details:
10/29/2024
"Found red tag by gas company, I checked the pallet and discovered that the inner is far from the pallet, reinstalled inner closer to the pallet and unit test ok. No more gas smell. Complete"
We serviced a
GE CAFE DOUBLE RANGE
Model CGS750P4M3W2
Near Ventura, California 93003
Isidro
Job Details:
10/29/2024
"Installed new lower over bake igniter, unit is now igniting and operating as designed, advised customer to run a burn off for 45 minutes at 400 degrees , cx approved repair"
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Lathrop, California 95330
William
Job Details:
10/29/2024
"Replaced drive motor & blower wheel, ran dryer cycle, unit operating as designed."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323AS8
Near Lompoc, California 93436
Kash S
Job Details:
10/29/2024
"Found unit making excessive noise while IM filling, found valve vibrating against rear panel, secured valve and panel, verified with cx that unit is operating at normal noise levels, advised cx to monitor for further issues, unit is fully operational at this time"
We serviced a
ZLINE RANGE - ELECTRIC
Model SGR30
Near Burbank, California 91505
Oscar
Job Details:
10/29/2024
Visual and physical inspection was conducted and through the functional testing a yellow feather was observed on the R F burner. So I have adjusted the orifice gas and air moisture and consumer was happy with results. Silvia 00833135
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Barstow, California 92311
Jonathan B.
Job Details:
10/29/2024
JB OUT 10/29/24Customer states unit will fill with water but not wash.Tested in NORMAL cycle. Verified nor fill function. Unit wash motor does not run.Installed replacement Sump and Motor assembly W12613579.Reassembled unit and tested again in NORMAL cycle with customer.Unit is now washing properly.No charge to customer.JOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near McFarland, California 93250
Esteban
Job Details:
10/29/2024
Broken actuator. Actuator was removed and replaced. Unit passed all test. Unit is working as intended.
We serviced a
KITCHENAID REFRGERATOR
Model KBRS20ETSS01
Near Los Angeles, California 91326
Ian Y
Job Details:
10/29/2024
Removed and replaced units bulbs and water filter housing. Unit now illuminated and water filter lid closes.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ10
Near Palmdale, California 93552
Jonathan
Job Details:
10/29/2024
Replace defective valve and tested unit and is working properly
We serviced a
AMANA REFRGERATOR
Model ASD2522WRS07
Near Palmdale, California 93551
Samson
Job Details:
10/29/2024
"Replaced bad condenser fan motor kit recommended by the tech support, unit test ok. Cx to allow for 24 hrs for maximum cooling. Complete"
We serviced a
MAYTAG WASHER
Model MVW6200KW4
Near Los Angeles, California 91306
Sean W
Job Details:
10/29/2024
"Replaced damaged pulley,and defective actuator.ran diagnostic cycle successfully without errror codes or interruption.washer now working properly."
We serviced a
KITCHENAID COMPACTOR
Model KTTS505ESS2
Near Bakersfield, California 93311
Randy
Job Details:
10/29/2024
New install. Latch loose. Door not closing all the way. Removed and installed properly. Unit now working as designed
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Moreno Valley, California 92557
Kevin
Job Details:
10/29/2024
Unit not starting cycle. I found that the motor was just humming. I found leaking capacitor causing issue. Removed and replaced capacitor. Tested unit. All tests good.
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Tehachapi, California 93561
Randy
Job Details:
10/29/2024
Unit would keep running f9e1. Would not fill. No water in float switch. Removed and replaced pump n motor. Tested. Now fills and washing. Now working as designed.
We serviced a
WHIRLPOOL OVEN
Model WFG525S0HZ
Near Los Angeles, California 91040
Samson
Job Details:
10/29/2024
Replaced bad hinges. Complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Orcutt, California 93455
George
Job Details:
10/29/2024
Found refrigerator not dispensing ice found rod for ice container off position reinsert unit functions tested 3 times complete return parts.
We serviced a
JENN-AIR MICROWAVE
Model JMW3430DS02
Near Los Angeles, California 91403
Leon
Job Details:
10/29/2024
W11236885Total s.c and labor $362.92Replaced console. Unit Working properly as required
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Ceres, California 95307
Timothy G
Job Details:
10/29/2024
Inspected unit and found softener tray over flowing. Checked for clog. No clog. Valve is spraying hard causing water to run out of softener tray. Replaced valves and unit is now working perfectly per design. Recalibrated load size and job completed
We serviced a
MAYTAG DRYER
Model MGD6200KW4
Near Los Angeles, California 91326
Sean W
Job Details:
10/29/2024
"Broken tab on door handle caused it to fall off of door.replaced broken handle with new one,door can now be opened and dryer is working properly."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WZF34X16DW08
Near Victorville, California 92395
Cesar
Job Details:
10/29/2024
Found loose ground wire connection at cabinet from power cord. This caused GFI to trip cutting off power to unit. Secured ground wires making sure cabinet is properly grounded all tested good. Customer had food loss do to no cool
We serviced a
KITCHEN AID RANGE
Model KSEG700ESS7
Near Fresno, California 93710
Timothy
Job Details:
10/29/2024
Had the customer run the unit at 400f for 1 hour. Took a temperature with thermocouples taped to the side of the unit until the temperature stabilized. The highest reading was 124f the limit is 152f. The gaskets look good the flew is installed correctly and the heat blanket is installed correctly. Unit is operating within expected parameters per WPTS 7740213824
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS1
Near Simi Valley, California 93065
Richard
Job Details:
10/29/2024
"Upon arrival, inspected unit and found unit not getting any water at all but union diagnostics unit gave me an F8E2 error code, which was a inlet water valve electrical problem replacing the water valve re-tested unit unit passed all the test and is working as intended job complete"
We serviced a
KITCHENAID OVEN
Model KOSE500EWH20
Near Bakersfield, California 93312
Brandon
Job Details:
10/29/2024
Ventilation piece under the door fell apart. I was able to put it back together and reinstall it. Unit is now directing airflow as designed.
We serviced a
JENN-AIR OVEN
Model JJW2427DS03
Near Los Angeles, California 90077
Leon
Job Details:
10/29/2024
W11232102Total $1446.34Collected full amount Replaced console Unit working properly as needed
We serviced a
MAYTAG DRYER - ELECTRIC
Model MGD4500MW1
Near Wasco, California 93280
Esteban
Job Details:
10/29/2024
Timer and knob were removed and replaced. Unit passed all test. Unit is working as intended.
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Lompoc, California 93436
Kash S
Job Details:
10/29/2024
"Found unit sharing during spin, found dampers failing, replaced dampers, verified with cx unit is spinning without excessive shaking or vibration, advised cx on load size and types for optimal operation, cx has no further questions/concerns, unit is fully operational at this time"
We serviced a
FRIGIDAIRE OVEN
Model GCWM3067AFA
Near Perris, California 92571
Kevin
Job Details:
10/29/2024
Unit giving error code F50 again and also gave F105 one time. I called tech line again ( file 87674184 ). They recommend replacing oven relay board. Customer declined at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Oak Park, California 91377
Richard
Job Details:
10/29/2024
"Upon arrival inspected unit Well, running water from the dispenser I found the Filter housing Leaking a lot found bad O-ring on quick fitting in housing. Replaced housing re-tested unit unit is no longer leaking. I ran about a gallon and a half of water and found no leaks. All ups are normal now. Job complete."
We serviced a
WHIRLPOOL LAUNDRY
Model WTW500CMW0
Near Bakersfield, California 93313
Raymond
Job Details:
10/29/2024
"Unit off balance, found loose strut, secured and tested, unit functioning as designed. Also explained proper loading and cycle selections."
We serviced a
WHIRLPOOL WASHER
Model WTW5005KW0
Near Tulare, California 93274
J.E.
Job Details:
10/29/2024
Cycled unit and found unit off balance. Installed new suspension and new hub retested unit now working as designed job completed
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Lathrop, California 95330
William
Job Details:
10/29/2024
"F2E1, Checked power to unit, checked air flow, reseated all connections to ui panel, checked HMI functions, unit operating as designed."
We serviced a
GE OVEN
Model PKD7000SN5SS
Near Bakersfield, California 93313
Raymond
Job Details:
10/29/2024
On arrival screen is stuck at setup. Power cycled unit and pulled error codes. None found. Went through setup again and unit completed setup. Tested unit and unit is operating as designed. Cx should follow up with manufacture or vendor for manuals or use and care guides.
We serviced a
JENN-AIR DISHWASHER
Model JDB8700AWS3
Near Nipomo, California 93444
Jack
Job Details:
10/29/2024
Found the outlet seems to be ok but the garbage disposal wont work either. Outlet really lose inside. Tested with another outlet and popped it. Had to reset it. Found main board has a short in it. Giving customer a quote for repair. Main board W10866118. Customer is going to purchase a new dishwasher after quote. Job completed
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Santa Paula, California 93060
Isidro
Job Details:
10/29/2024
"Unresponsive UI control panel. Installed new UI panel, unit is now coming on and operating as designed at this time of service also"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT910SSYM1
Near Thousand Oaks, California 91362
Richard
Job Details:
10/29/2024
On arrival inspected unit. Customer stated that unit will not drain. Put unit into diagnostics only error code that the unit gave me was an F6 East six which was water temperature water to cold advise customer to make sure he runs the hot water in his Fossett before starting a cycle to ensure hot water going to the unit inspected drain line there was a possible obstruction in the drain line. I retested unit and diagnostics unit passed all tests and diagnostics and its draining as intended. Ran diagnostic three times unit drained perfectly. It is possible that the garbage disposal was full of food at the time of At the time of the cycle and did not allow unit to drain advise customer for smell to buy a fresh pods and run a cleaning cycle on the unit and do this at least once a month at the moment all ups are normal advising customers they have any more issues to please call us back job complete
We serviced a
AMANA WASHER
Model NTW4516FW
Near Port Hueneme, California 93041
Ian Y
Job Details:
10/29/2024
"Found that units valve connection to cold water solenoid had backed out. Reconnected solenoid. Tested, unit now filling. Customer also complaining about water level. Explained to customer that this washer was high-efficiency and only gave out a specific amount of water."
We serviced a
MAYTAG LAUNDRY
Model MVWB765FW0
Near Port Hueneme, California 93041
Ian Y
Job Details:
10/29/2024
"Found units clip holding pump to drain hose slipped halfway off allowing water to come out of bottom of hose. Had new clip in car. Secured hose and clipped it properly. Pulled on hose to make sure there wouldnt be repeat problem. Hose was secure. Tested, unit no longer leaking."
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Bakersfield, California 93308
Joe P
Job Details:
10/29/2024
"Installed new ACU board,ran diagnostic cycle test passed all test. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW1
Near Bakersfield, California 93312
Joe P
Job Details:
10/29/2024
"Code F1E1 drain pump. Checked drain pump, has 120v and good neutral. Pump has no resistance open. customer declined at this time."
We serviced a
WHIRLPOOL FREEZER
Model WRS325SDHZ00
Near Camarillo, California 93010
Ian Y
Job Details:
10/29/2024
"Found unit in a no cooling situation. No frost pattern on evap. All fans running properly. Checked high and low side lines and both werent even slightly hot. Quoted customer between 800$-1000$ for compressor, Evap, labor and service fee. Customer said he would consider repair but would talk to fiancé and they were leaning more towards getting a new refrigerator."
We serviced a
GENERAL ELECTRIC WASH/DRY COMBO
Model PFQ97HSPV0DS
Near Bakersfield, California 93309
Joe P
Job Details:
10/29/2024
"Drain filter and lint filter plugged,cleaned out filters. Ran heat pump test and auto test all passed. Job complete."
We serviced a
WHIRLPOOL DRYER
Model WGD4850HW2
Near Tulare, California 93274
Enrique
Job Details:
10/29/2024
Found Dryer not tumbling. Belt got disconnected from idler pulley. Re-installed the belt. Dryer tested normal.
We serviced a
MAYTAG DRYER
Model MGD4500MW0
Near Nipomo, California 93444
Jack
Job Details:
10/29/2024
Unit started up making a thumping type sound. Found a ball of stuff that also had some metal shavings in it were it clumped and scraped and thump sound in blower wheel. Put all back together and cleaned out blower wheel area and vent area. Checked heat tube and were the heat vents through. Unit even had a load in it. Now functioning as designed. Adjusted the blower wheel and made sure nothing was behind it and checked drum. Job completed
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Simi Valley, California 93063
Ian Y
Job Details:
10/28/2024
Ran machine in diagnostic and found that it was draining and wash motor was working properly. Control panel wasnt responding to touch until I put unit in diagnostic. Unit wasnt storing any error codes. Ordering new panel and control board. Most likely wont replace sump but bringing back just in case. ; ordrng 1 W11415066 (Control) and 1 W11340447 (UI)
We serviced a
GENERAL ELECTRIC WASHER
Model PFQ97HSPV0DS
Near Ventura, California 93003
Isidro
Job Details:
10/28/2024
"Torn fine filter and leaking cracked water drain pump, correcting issue by; ordrng 1 WH01X35685 (Lint filter assembly) and 1 WH11X29539 (Drain pump assembly)"
We serviced a
GENERAL ELECTRIC WASHER
Model GTW485ASW0WB
Near Ventura, California 93003
Kenneth
Job Details:
10/28/2024
Customer indicating they are still having same issues. Plugged in GE device and found there is no faults. Or cycle history. Called techline who had me manually clear out of balance error that never showed up on GE device. And then informed me that the reason customer has fabric in the agitator at the end of the cycle. Is cause the unit isnt selected to fabric softener which only changes the rinse and not the actual spin so softener should still dispense out of the agitator during the spin. Confirmed I had programmed new board to the proper personality. Unit is working properly per techline. Techline informed me to have customer set the unit to rinse with softener and see if they are still experiencing issues at that time. File#14651395 - Charles; O-emld tckt
We serviced a
KITCHENAID REFRIGERATOR
Model KBFN502ESS05
Near Simi Valley, California 93065
Ian Y
Job Details:
10/28/2024
Customer advised that door wasnt fixed when last tech left. Customer attempted to take spring out of top right hinge and lost screw for it. Need new screw and bushing. Ordering new hinge assembly. ; ordrng 1 W10121046 (Hinge) and 1 2307857 (Hinge) and 2 W11370632 (Screw)s and 2 8281164 (Stainless screw)s and 1 W10752868 (Door stop) and 2 W10761279 (Screw)s
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW1
Near Keyes, California 95328
Timothy G
Job Details:
10/28/2024
Inspected unit and found harnes has shorted out at pump. Ordered another lower harness. Filling up Thursday 31st. Part may not be available. Please notify Cx if part is not. I can repair this call Saturday if part is available then.; ordrng 1 W11643701 (Wire harnes2)
We serviced a
FRIGIDAIRE RANGE - ELECTRIC
Model GCFI3060BFA
Near Templeton, California 93465
Jack
Job Details:
10/28/2024
Found that the one pointer tech line said part is discontinued 5304536905. No longer available. Part to help take off top. Craig with tech line. Pan assembly 5304528600. Interface board is 5304536436. Took unit completely apart to see board assembly pan is damaged and needs replacing. Plus need part 5304536905 reliable has part and Frigidaire has them in stock. 800-599-7569 can order that tool assembly kit. File for today 87680433. Customer is calling in to see were they are going on this repair. ; ordrng 1 5304536905 (Tool assembly) and 1 5304528600 (Pan assembly) and 1 5304536436 (Interface board)

