Fixed- installed new parts (2 thermostats) bake cycle is now working and all top burners are working fine as well- cx ok repair

"Not dispensing detergent, replaced detergent pump tested unit working good"

"Replaced actuator with original part, ran self disgnostic cycle, unit operating as designed"

Found unit with Key stuck under washplate causing rubbing noises. Removed and tested unit. Unit functions as intended. No error codes.

JB out 3/23/22. Installed replacement strike as ordered. Tested operation with customer. Unit now operates as designed. No charge to customer. JOB COMPLETE

Sr number 7733253526. 800-331-7456 safety team number. Called the tech line and safety team. Checked all connections for gas leaks and none were found the front right burner did have issues lighting. Once lit the flames were normal. Unable to verify gas leak. Customer stated the gas company came out and used a carbon monoxide detector and said it was at792 ppm. I wanted the video of the gas company employee preforming the check but he was checking it on the cooktop and that is incorrect from what tech line says. Carbon monoxide meters are not being sent out by whirlpool at this moment because of Covid. I did damage the cabinet door to the right of the stove. I informed the office. Sr 7733212397 safety team sr number. All checked ok at this time.

Installed new parts. All ops now checking out normal.

"Customer canceled, Customer thought they had a 10 year warranty"

Found washer with exexively soap removed retested check out ok complete no dents or dings cause by tech.

Installed new drum. All ops now checking normal.

"Unit leaking by freezer door, found water line not fully seated in connector fitting causing a drip, fully seated line and unit stopped leaking"

Replaced failed parts tested unit all tested good

"On arrival I installed and secured new soap dispenser, I tested unit for leaks, no leaks visible, unit is now operating properly as designed at this time of service"

"Customer concerns, upright freezer started building up snow around gasket. Gap on upper left corner. I adjusted the legs/level the freezer, all functions tested as designed."

Fixed for fcc. Found orbital spray had popped off and melted on heater element - installed new one (orbital spray) lower spray are in rotating as designed- cx ok repair

Replaced door and vent all tested good

"Upon arrival, reset power to board and checked all settings. Cycles ice maker and checked to make sure water dispensing properly . Unit ran as designed."

Replaced defective fill valve and tested unit.Tested ok

"Adjusted water level to ice machine fill, set to max. Please allow time for ice maker to operate for some time."

"Use autho# K117AU0WPL2Returned, replaced defective manifold and as designed operation was restored with no leaks. 1 W10818266 (manifold)"

"Replaced inlet water valve assembly. Calibrated machine, ran diagnostics, all units ops check fine. Upon completing the repair, the customer brought up a new issue, the unit is noisy during the spin cycle. Found the belt was the source of the noise, replaced the drive belt, the unit is no longer noisy."

"On arrival I found broken middle arm assembly, i installed and secured new middle arm assembly and spray arm, tested unit, unit is now operating properly as designed at this time of service"

"Ran diagnostics. Had f5e1, f2e1 error codes. Found lid lock failing. Replaced latch assembly. Ran load size calibration, auto test cycle. Locks/unlocks,fills , agitates, drains, rinses, dispenses, and spins properly at this time. Instructed customer on normal water levels. Unit is working properly as designed. Complete.; used 1 W10810403 (Latch) from stock"

Pulled unit out removed all panels found thermostat burned and wiring harness fried thats what was causing the burning smell. Removed and replaced harnesses and thermostat. Tested all works good at this time.

"CX says the unit is noisy. Confirmed issue. The actuator is clicking hard into spin. Replaced component, cal passed. All ops normal."

Found refrigerator freezer reading 29 degrees not building a full frost pattern per Frigidaire if unit needs a seal system customer to call customer care for further info complete no dents or dings cause bytech.

"Customer concern was no ice, unit had ice box fan frozen over due to freezer door gasket being ripped and leaking air. Thawed out and customer did not want to replace gasket. Unit is back operational."

"Replaced latch Assy, ran self diagnostic cycle, unit operating as designed. Cx refused to sign off on job."

"Fixed- installed new parts (cntrl elec, latch) calibration test pass- auto test pass- no error codes- no leaks- cx ok repair"

Found high limit thermostat open. Replaced with thermostat with truck stock WE04X26138; used 1 WE04X26138 (High limit thermostat) from stock

"First manifold showed up as a console for a front load washer, second one was correct. Installed and tested all ok."

"Found tripped back interlock causing door not to close, tripped interlock back collected 125"

Found micro hood exexively loud and not heating found flap on backwards reposition replaced magnetron test ok complete no dents or dings cause by tech paid in full with credit card.

"Replaced clock assembly (board). Checked ops, all units ops check fine, it is working as designed."

Removed and replaced coils and drum. Tested unit. All tests good.

"JB out 3/23/22 customer states a flashing light sequence of 8 and 4 was observed. Customer then corrected a small water drip at the water inlet connection prior to my service visit of 3/23/22. Ran diagnostics and verified only F8E4 indicating overflow/Float switch open. Cleared stored code. Removed toe panel Advise water being supplied to dishwasher is far below the required 120f minimum as outlined in the supplied installation instructions. Suggest the purchase, installation and use of a Point of Use Hot water heater mounted under the kitchen sink and run ONLY to the two dishwashers (set to 125f) to insure no less than 120 f water temperature is supplied to the dishwasher(s) the moment that the start button is pressed to insure proper cleaning performance. No parts used. No charge to customer. JOB COMPLETE"

"JB out 3/23/22 upon arrival verified loud noise from freezer Fan fan scrapping ice and frost. Inspected FC drawer and verified it closes and seals but cabinet was not leveled properly when installed. Amount of frost indicates drawer has been left afar causing heavy frost buildup. Customer states frost has been present for one month. See quick pic photo showing some packages not cover in frost as drawer was closed and sealed properly. Some item in FC heavily frosted indicating items stored in FC during a period of time when the drawer was not closed or sealing completely . Advised customer to remove all perishable foods and place in a different refrigerator, unplug this unit and allow to defrost with all doors opened for 24-36 hours. After all water from melted ice and frost is wiped up the unit can be plugged in and allowed to run for 8-10 hours before returning perishable foods to be stored. Instructed customer to remove toe panel grille EVERY 2 MONTHS for the life of the refrigerator and clean condenser coils to restore low electrical operating costs, reduce over run time and increase life of the product. NOTE: Blocked condenser coils may cause premature compressor failure and may or may not be covered by extended warranty plan contract. No parts used. No charge to customer today. JOB COMPLETE"

"Removed and replaced parts listed,tested ops unit now working ok.7733253226"

Called WPTS(7733256709) and documented the call.

Installed new parts and re-tested unit all test pass at time of service. Job completed

Ran a check on unit. Heat is there. Checked vent.vent was blocked. Check and cleaned out. Clothes should dry a lot better. Checked for codes and unit didnt have any. Ran another cycle and unit seems to be working a lot better. Job completed

"Customer concerns, washer not advancing wash cycles. In diagnostics found, shifter fault. Installed new shifter ( truck stock ), performed calibration. All functions worked as designed, no leaks.; used 1 W11481722 ( Actuator) from stock"

Installed compressor kit. Vacc and charged system. Holding charge. 24 hrs to freeze.

Arrived on site with parts. Removed and replaced faulty board and rechecked unit operating condition . Lights come on as well as all other functions. Unit tans as designed. Core for 24537108 not obtained because Core is destroyed.

Customer concerned with wash performance. I tested unit and found actuator not engaging. Removed and replaced actuator. Tested unit. All tests good. ; used 1 W10913953 ( ACTUATOR) from stock

"Removed unit from cabinet. Removed all racks and tubing from inside the unit. Replaced sump assembly and hose . Reassembled unit and tested. Unit checks ok, no leaks noted. Reinstalled unit into cabinet."

"JB out 3/23/22. Installed replacement Lower harness. Reassembled unit and tested fill, wash drain and spin functions. Unit now operates as designed. No charge to customer. JOB COMPLETE"

Cycled power and cleared board.Tested ok

Unit is dead. Lock is stuck shut. Wont even release. Got clothes out so they wont mold. Unit had no power because braker was half tripped. Unit is in a cycle and running correctly. Showed customer and unit is working. Job completed

"Found the unit, not cooling, verify problem compressor not running, replace compressor,service valve and drier, charge refrigerant 68g R600a check compressor condenser and refrigerator fan motors running normal"

Customer stated that are getting condensation inside the freezer that is freezing. I found a freezer door sitting too low not sealing correctly. Also found door seal is not ceiling heat treated door seal move door up tested all works good this time

"Removed and replaced parts listed, unit now checks ok, cx approved."

"Unit shakes bad, found Suspension rods bad, replaced"

"Didnt have valve ending in 41320. Reordered parts. Called office and left them know. Removed power installed all parts. Assembled unit, test for ops. Unit is dispensing water. All ops normal."

"Unit was going straight into drain mode, unable to stop this. Attempted releasing pressure hose and control stop for a second and continued to drain. Removed and replaced control it solved issue. Provided Estimate cx approved. Calibrated and tested ops unit now working as designed Sr#7733256242"

"SR7733253054 replace pump. Replaced pressure switch, no change. Contacted techline and he recommended I replace the drain pump. Replaced pump, diag tested all ok, no leaks, pumps good, drains well. Watched entire drain and spin, no remaining water, drain pump cycles as normal. Only time I found remaining water is if the cycle is being canceled mid cycle or spin."

Customer stated that the unit is making a grinding sound. I found some wear marks on slider. Removed and replaced slider assy. Tested unit. All tests good.

Installed new part. All ops now checking okay.

Unit had start device incorrectly on compressor causing it to not start replaced capacitor and unit is backmopestional

Replaced door and thermostat all tested good

After replacing the faulty heating element the front left burner is now operating. Job completed. All functions tested properly.

"Replaced ui panel, checked oven sensors, found 3 inch long sensors, tested oven functions, rechecked for codes, unit operating as designed"

Replacing parts listed. Tested unit and unit is responsive to all the controls. Tested and unit heats correctly and is working like it should. Job completed

Found unit with baffle stuck open. Replaced and unit now working as intended.

Arrived with parts . Installed new panel. Rechecked ops. Unit ran as designed.

"Fixed- installed new parts (capacitor, mag, diode) tested unit is now heating as designed- cx ok repair."

Ran unit in diagnostic and unit passed al tests at time of service. F0E2 suds. Customer has been washing her clothes on bulky setting all loads on bulky. Explained to her shes been using wrong cycle for her loads. Unit is agitating as intended. Job complete.

Picked up old unit to haul back to the shop and dropped off check

Installed new part and re-tested unit all test pass at time of service. Job completed

Not picking up anything from jc he is off for a month

"Pulled unit from wall. Disassembled unit, and replaced the control. Board was in the control Box. Installed both components. Installed microwave. Test passed. All ops normal. Unit starts when start button pushed."

"Replaced actuator with original part, ran self disgnostic cycle, unit operating as designed"

Found unit with Key stuck under washplate causing rubbing noises. Removed and tested unit. Unit functions as intended. No error codes.

"Replaced defective gas coils, drum and idler kit.Tested ok"

Rick tech line. Unit freezing in fresh food section. Sr 7733254879. No food up by the damper. Food was blocking damper and food was to close to damper causing stuff to freeze. Went over with tech line and customer. Job completed

Installed new parts. All ops now checking out normal.

"Customer canceled, Customer thought they had a 10 year warranty"

Door latch not lining up with catch. Adjusted top of tub for proper contact.Tested ok

"Removed and replaced door, asked cx to monitor and report any issues."

Replaced failed parts tested unit all tested good

Cx states that unit is not working properly Cx states that food freezing in fresh food compartment Readjust temperature and freezer door Unit working properly as designed

install part tested unit all ops normal

Replaced door and vent all tested good

"Upon arrival, reset power to board and checked all settings. Cycles ice maker and checked to make sure water dispensing properly . Unit ran as designed."

Replaced defective coin drop.Tested ok

"On arrival I found broken middle arm assembly, i installed and secured new middle arm assembly and spray arm, tested unit, unit is now operating properly as designed at this time of service"

Installed parts and ran cycle. Unit passed all tests and is operating as designed.

Found refrigerator freezer reading 29 degrees not building a full frost pattern per Frigidaire if unit needs a seal system customer to call customer care for further info complete no dents or dings cause bytech.

"Customer concern was no ice, unit had ice box fan frozen over due to freezer door gasket being ripped and leaking air. Thawed out and customer did not want to replace gasket. Unit is back operational."

"Replaced compressor , filter dryer, installed service port, swept system with nitrogen, pressure tested system with nitrogen, found no pressure drop for 15 min. recharge system, unit cooling at this time, sealed system warranty job.; used 1 W10913906 (Access port) from stock"

"First manifold showed up as a console for a front load washer, second one was correct. Installed and tested all ok."

"Found tripped back interlock causing door not to close, tripped interlock back collected 125"

Installed console and ui. Tested unit. Unit is working properly. Customer approves

Installed new diffuser. All ops now checking out normal. Job complete.

Removed and replaced coils and drum. Tested unit. All tests good.

"JB out 3/23/22 customer states a flashing light sequence of 8 and 4 was observed. Customer then corrected a small water drip at the water inlet connection prior to my service visit of 3/23/22. Ran diagnostics and verified only F8E4 indicating overflow/Float switch open. Cleared stored code. Removed toe panel Advise water being supplied to dishwasher is far below the required 120f minimum as outlined in the supplied installation instructions. Suggest the purchase, installation and use of a Point of Use Hot water heater mounted under the kitchen sink and run ONLY to the two dishwashers (set to 125f) to insure no less than 120 f water temperature is supplied to the dishwasher(s) the moment that the start button is pressed to insure proper cleaning performance. No parts used. No charge to customer. JOB COMPLETE"

Fixed- installed new parts (2 thermostats) bake cycle is now working and all top burners are working fine as well- cx ok repair

Installed new parts and re-tested unit all test pass at time of service. Job completed

Ran a check on unit. Heat is there. Checked vent.vent was blocked. Check and cleaned out. Clothes should dry a lot better. Checked for codes and unit didnt have any. Ran another cycle and unit seems to be working a lot better. Job completed

JB out 3/23/22. Installed replacement strike as ordered. Tested operation with customer. Unit now operates as designed. No charge to customer. JOB COMPLETE