Local Reviews

Tyler F.
REFRIGERATOR MAYTAG MFI2269FRZ02 Customer stated that the ice maker is not working. Found ice maker cycled but no water is going to ice maker. Removed and replaced valve. Tested all works good at this time. Separate issue than before.

Tyler F.
WASHER MAYTAG MHW5100DW0 Customer stated that the unit shut off and would not co e back on. Found no error codes. Found drain hose too far in drain which may have caused siphoning. Calibrated unit and tested all works good at this time.

Tyler F.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Customer stated that the upper rack adjusters have broken. Removed and replaced adjuster kit tested all works good at this time.

Steven W.
DOUBLE WALL OVEN KITCHENAID KODE507ESS03 Lower outer door glass shattered. Replaced lower outer door assembly. Door is opening/ closing properly. Unit is heating properly at this time. Complete.

Steven W.
WASHER AMANA NTW4516FW1 "Replaced control, pump, strike, capacitor, actuator. Ran diagnostics. No error codes. Ran auto test cycle, calibration- passed. Fills, agitates, drains, rinses, & spins properly. Advised not to use ECO detergents. Complete."

Steven W.
DRYER WHIRLPOOL WGD4815EW2 "Found vent hood plugged( had screen inside ). Removed screen from vent hood. Dryer is tumbling, heating properly. Instructed customer to have vent hood replaced. Complete."

Steven W.
REFRIGERATOR WHIRLPOOL WRT134TFDW00 Found cold control not cutting back on. Replaced thermostat. Unit is cooling properly at this time. Complete.

William L.
DISHWASHER KITCHENAID KUDS30FXWH8 "found fill tube rotted, under kitchen Island area, ordered fill tube for unit.; ordrng 1 W10878507 (hose-fill)"

Raymond D.
REFRIGERATOR KITCHENAID KSC24C8EYW00 Upon arrival unit had cracked liner around lower cabinet. Used adhesive to seal open liner.

William L.
RANGE WHIRLPOOL WFG525S0HZ0 "found hinges broken, ordered hinges for unit.; ordrng 1 W10347464 (hinge-door) and 1 W10647259 (hinge-recv)"

William L.
WASHER AMANA NTW4516FW3 "checked power in to unit & main control , ordered main control; ordrng 1 W11170317 (main control)"

William L.
DISHWASHER WHIRLPOOL WDTA50SAHZ0 "F4E3, ran diagnostics, checked connections, ordered pump/motor assembly; ordrng 1 W11087376 (pump&motor)"

William L.
REFRIGERATOR WHIRLPOOL WRS325SDHB00 "adjusted front leveling to stop doors from swinging open, found condenser fan motor not starting up causing divider wall of fridge to over heat, ordered condenser motor, instructed cx no ice dispenser.; ordrng 1 W10854034 (motor-cond)"

William L.
REFRIGERATOR WHIRLPOOL MSD2657HES "found evap fan not running, ordered evap fan motor; ordrng 1 WPW10128551 (evaporator fan motor)"

Patrick C.
WASHER MAYTAG MVWX655DW1 Customer having issues with unit not wanting to start. Seems to be no power. Checked plug and power was sufficient. Checked power to control and that seemed good too. No green indicator light on the control. Needs new control. Removed and replaced. Calibrated and ran auto test. All ops checked good

Tyler F.
OVEN MAYTAG MEW7527AS01 Customer stated that the oven is dead after self clean. Ordering thermostat and thermal fuse in stock.; ordrng 1 WP4449751 (thrmst-fix) and 1 WPW10545255 (fuse-thrml)

Tyler F.
REFIRGERATOR WHIRLPOOL WRS571CIHZ00 Customer stated that ice maker sensor is hanging. Found temp sensor off ice maker. Ordering ice maker in stock.; ordrng 1 W10873791 (icemaker)

Patrick C.
WASHER AMANA NTW4605EW0 Removed and replaced agitator. Gear case wasn’t need as it wasn’t damaged while removing agitator

Tyler F.
REFRIGERATOR WHIRLPOOL WRF990SLAM00 Customer stated that the unit is not cooling in either compartment. Found sealed system leak in refer evaporator. Ordering compressor and evaporator. ; ordrng 1 W10276644 (compressor) and 1 W10917531 (evaporator)

Michael M.
WASHER MAYTAG MVWC565FW1 Unit had stripped agitator.Removed and replaced agitator.Checked diagnostics and found no faults stored.Ran auto service test and passed with no issues. Unit ops are normal job complete

Tyler F.
WASHER MAYTAG MHWE950WW01 Customer stated that door boot is ripped. Ordering door boot in stock.; ordrng 1 WP8182119 (bellow)

Michael M.
KITCHEN WHIRLPOOL KEWD105HSS Removed unit. Removed and replaced parts. Unit ops as intended. On install the lower drawer was removed to access electrical plug. When drawer was reinstalled the left rail became damaged. Tech removed left drawer rail.

Tyler F.
DISHWASHER KITCHENAID KDPE234GPS0 Customer stated that the lower spray arm is not working. Found error code for the diverter. Tested and found diverter is not working. Ordering sump assembly in stock.; ordrng 1 W11085683 (pump&motor)

Michael M.
VENT HOOD KITCHENAID KXW9736YSS0 Cx states a screw came out of the unit.tech finds the housing has crackedRemoved and replaced with new plastic bezel. Unit ops as intended job complete

Michael M.
DRYER WHIRLPOOL WGD5000DW3 Cx States unit is not drying.Tech found unit heats but has lint build up in wall. Advised cx to clean lint from exhaust. Rollers were squealing so installed dryer repair kit pn 4392065Unit ops as designed job complete; used 1 4392065 (DRYER REPAIR KIT) from stock

Michael M.
VENT HOOD KITCHENAID KXW9736YSS0 Cx states a screw came out of the unit.tech finds the housing has crackedRemoved and replaced with new plastic bezel. Unit ops as intended job complete

Steven W.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 "Filter is not stuck. Instructed customer. Found upper deli drawer binding. Needs shelf/ roller assembly, slides.; ordrng 1 W11257202 (PAN-DELI) and 1 WPW10345310 (shelf-glas) and 1 WPW10346890 (slide) and 1 WPW10346891 (slide)"

Kevin M.
DRYER MAYTAG MGDB835DC4 "Customer concerned with not all the load drying during a cycle. I tested gas coils and sensors, all tests normal. I changed customer focused dry level to +30%. Instructed customer on mixed loads and blankets. All tests good."

Kevin M.
RANGE JENN-AIR JGS1450DP0 Unit giving cooling fan error when customer uses oven in bake. I found cooling fan not spinning fast enough and causing error code. Removed and replaced cooling fan. Tested unit. All tests good.

Steven W.
REFRIGERATOR WHIRLPOOL WRT111SFDB03 "Found compressor running, not cooling. Partial frost pattern. Possible weak compressor ( customer said it was clicking also ). Order compressor, drier; ordrng 1 W10843121 (drier-tube) and 1 WPW10507886 (compressor)"

Kevin M.
RANGE KITCHENAID KSGG700ESS1 Customer concerned with glass fogging up during cooking. I found glass not sealed all the way. I correctly sealed door. All tests good. Customer also has burnt out bulbs in oven. showed customer how to replace. All tests good.

Kevin M.
WASHER MAYTAG MVWB835DW3 Unit not filling. I found failed water valve not allowing water to enter unit. Removed and replaced valve tested unit. All tests normal.

Raymond D.
DRYER MAYTAG MGD5500FW0 Upon arrival drum seal falling off. Drum defective. Need drum.; ordrng 1 W10381481 (drum)

Raymond D.
DRYER WHIRLPOOL WGD8000DW1 "Replaced thermal fuse and thermistor, tested, unit still not glowing. Found cracked igniter and open thermal cutoff. Bypassed and replaced igniter. Tested unit. still not glowing, inspected control board and found burned marks. Needs control and cutoff.; ordrng 1 W10802080 (cntrl-elec) and 1 WP8573713 (cutoff-tml), used 1 279311 (IGNITOR KIT & BRACKE) from stock"

Raymond D.
FREEZER WHIRLPOOL WZF34X16DW04 Upon arrival unit making same noise. Found compressor making excessive vibration noise.needs compressor; ordrng 1 W10507884 (compressor)

Kenneth M.
WASHER ROPER RTW4516FW Found unit not advancing through cycles well due to cold water clogged with gunk due to well. Informed customer on how to clean out water valve filter to insure unit doesn’t long fill. Found hot water to cold. And cold to hot. Switched around water lines to correct valves. Tested unit. Unit is now working properly. Customer approves function at this time.

Raymond D.
WASHER WHIRLPOOL WTW7500GW0 Upon arrival water valve leaking. ; ordrng 1 W11165546 (VALVE)

Kenneth M.
OVEN WHIRLPOOL WOC54EC7HW00 Rattle in conduit. Adjusted conduit to keep from rattling. Customer approves. Functions good.

Patrick C.
WASHER MAYTAG MVWB725BW0 Customer having issues with the unit not wanting to drain. Checked out the unit and found long drain error. Pump is just buzzing. Getting 120 to the pump. No blockage in pump. Needs new one ; ordrng 1 WPW10409079 (pump-water)

Patrick C.
REFRIGERATOR WHIRLPOOL WRT134TFDW00 Door is not shutting properly. Hinges seem to be fine. Broken washer at the hinge pin. Nothing is blocking the door from shutting. Needs new door and hinges ; ordrng 1 LW10573360 (dor-fip) and 1 WP2166037 (hinge-door) and 1 WP2325482 (hinge) and 1 WP2325483 (hinge-pin) and 1 WP489467 (washer)

Kenneth M.
WASHER WHIRLPOOL WT49470CW Got to home. Unit was LG. Not a WPl. Unable to service.

Patrick C.
REFRIGERATOR WHIRLPOOL WRV986FDEM00 Removed and replaced. Lights still out. The pantry led board is causing issues in the circuit ; ordrng 1 WPW10677119 (cntrl-elec)
Kegan N.
DISHWASHER AMANA ADB1400AGW1 "Customer stated unit not drying dishes. Entered diagnostics, ran test cycle, no error codes. Noticed large amount of SUDS at bottom of unit. Removed SUDS, tested again, heater engaging, unit working well this time. Informed customer to use only recommended amount of detergent."
Kegan N.
REFRIGERATOR FRIGIDAIRE FFHS2611PF "Customer stated icemaker leaking water. Inspected unit, noticed that funnel had a block of ice causing water to splash out when filling. Removed ice, cycled icemaker, test good, no spills."
Kegan N.
REFRIGERATOR WHIRLPOOL WRS315SDHZ00 "Customer stated ice maker not working. Inspected unit, noticed that bail was out of position. Repositioned, reset unit, and tested, test good."

Michael M.
REFRIGERATOR KITCHENAID KRSF505ESS00 Cx states ice is melting inside ice bin.Tech removed lower dispenser parts but was unable to access User interface tabs for removal due to a separator plate. Tech was not able to remove separator plate and Cx stopped the repair so no damage would occur.
Kegan N.
WASHER WHIRLPOOL WTW5000DW2 "Customer stated washer spinning on its own. Inspected unit, enter diagnostics, no error codes present, ran test cycle, test good. Instructed customer to monitor unit"

Jim S.
WASHER WHIRLPOOL WTW8500DC0 "F3E2, F2E1, F6E2Replaced gear case and wash plate. Unit tested ok"

Jim S.
REFRIGERATOR JENN-AIR JFFCC72EFP00 Replaced fan and covers to prevent frost and ice build up

Michael M.
DISHWASHER KITCHENAID KDPE234GPS0 Cx states unit is not washing.Unit fills and drains but deserter motor just clicks.Ordering sump assembly W11085683; ordrng 1 W11085683 (pump&motor)

Jim S.
DRYER WHIRLPOOL WGD5500XW0 Reinstalled drive belt pulley

Kevin M.
WASHER MAYTAG MVWB880BW0 "Unit making loud noise during spin cycle and giving UL error codes. I found that the tub seal started leaking and flushed out tub bearings causing loud noise. Unit giving UL code due to stator and rotor getting wet and basket hub splines are worn down. Unit will need stator, rotor, basket hub, and bearing kit. ordrng 1 W10435302 (bearing), 91.51, 1 W10820039 (hub), 18.14,"

Jim S.
DRYER MAYTAG MEDC200XW1 Replaced faulty timer

Kevin M.
REFRIGERATOR KITCHENAID KSSC48QMS02 Compressor turning off and on and user interface lights cycling off and on. Failed relay on main control causing issue. Unit needs main control. Ordering part. Customer needs service before 10am. ; ordrng 1 W10818296 (cntrl-elec)

Jim S.
REFRIGERATOR WHIRLPOOL WRS321SDHV01 Adjusted doors and tighten the handles. Unit tested ok

Jim S.
DISHWASHER FRIGIDAIRE FGHD2433KB1 Replaced door seal and water diverted. Ran unit and found no leaks. Unit tested ok

Jim S.
REFIRGERATOR WHIRLPOOL WRT771RWYW01 Cleared defrost drain line

Jim S.
RANGE GENERAL ELECTRIC CGS990SET4SS Replaced board and glow bar ignitor. Unit tested ok

Kenneth M.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Installed drain pump and found locking tab was broken. Ordering new sump assembly; ordrng 1 W11085683 (pump&motor)

Jesus C.
REFIRGERATOR WHIRLPOOL WRS571CIHZ01 Removed diffuser and installed new. Pulled unit out and replaced valves. Tested component and are working. Unit is now working as design.

Kenneth M.
MICROHOOD GE JVM6172DK2BB Found unit making a loud vibrate noise. Found cooling fan cover broken so cooling fan is getting excessive viberations. Ordering vent fan. No low speed. ; ordrng 1 WB26X26792 (ventilation motor) and 1 WB34X21786 (cover motor)

Kenneth M.
FREEZER JENN-AIR JFX2897DRM02 Found unit icing up around adapter. Ordering new adapter kit ; ordrng 1 W11294907 (ICEMAKER) and 1 WPW10635022 (adapter)

Jesus C.
WASHER MAYTAG MVWC565FW1 Customer states that unit is not getting enough water. Checked unit and found error code. Ran manual test and found the cold water valve not opening. Removed hose and panel replaced control and valve. Calibrated unit and ran diagnostics. Unit is now working as design.F8-E1 long fill

James M.
DRYER ELECTRIC WHIRLPOOL LAV3600AWW Customer stated there's a noise during spin cycle. Tested unit and found unit off balance due to flooring causing unit to wobble during spin. Repositioned unit best as I could to eliminate wobble. Unit is functioning properly at this time.

Kenneth M.
DRYER GE GTD65EBSJWS Found unit DOA. Proper voltage to unit. But not powering on. Found control board dead. Ordering new control board; ordrng 1 WE04X25474 (chassis and board as)

James M.
WASHER WHIRLPOOL WTW4816FW2 "Replaced cntrl elect and tested unit. Unit now functioning properly and customer approves. No dents, dings, or blemishes on or around unit."

Kenneth M.
FREEZER KITCHENAID KRFF305ESS00 Found unit with condensation on mullion. Found humidity control not on. Turned on humidity control. Tested. Unit is working properly. Fund mullion bowed. So not allowing fridge door to seal properly. Ordering new mullion. Also ordering damper control. Loud noisy. And not opening closing properly. ; ordrng 1 WP12722803AP (rail-mulln) and 1 WPW10594329 (control)

James M.
REFRIGERATOR WHIRLPOOL WRS571CIDM "Replaced door and tested unit. Everything working as intended at this time. No dents, dings, or blemishes on or around unit caused by tech."
Kegan N.
REFRIGERATOR WHIRLPOOL WRS331SDHW00 "Customer stated refrigerator making loud noise when operating. Inspected unit, compressor knocking, broken spring. Ordering compressor.; ordrng 1 W10276644 (compressor)"

James M.
WASHER MAYTAG MHW5100DW0 "Unit has power. Tested unit and found it to be fully functional at this time. No dents, dings, or blemishes on or around unit caused by tech."

James G.
WASHER MAYTAG MVWB755DW0 Replaced listed part Tested ok
Kegan N.
REFRIGERATOR WHIRLPOOL WRS970CIDE01 "Customer stated unable to remove water filter from housing. Inspected unit, water filter housing defective, ordering part.; ordrng 1 WPW10394053 (housing)"

James G.
OVEN WHIRLPOOL WFG770H0FZ0 Replaced listed part due to sensor out of range Tested ok

James G.
RANGE GE JB750EJ5ES "Found burnt wire at control plug, was able to repair damage and tested ok"

James G.
DISHWASHER GE GDF520PGJ5WW Replaced listed part Tested ok

James G.
WASHER WHIRLPOOL WTW8540BW0 Rotor bolt backed out Removed and reinstalled with loc-tite Tested ok

James G.
STOVE AMANA ARG3300XDW0 Cleared pilot orifice on right hand burners and tested all functions also checked for any gas leaks Tested ok

Jim S.
REFRIGERATOR WHIRLPOOL WRX988SIBM01 "The unit completely shut down. Will need to order the user interface and relay board; ordrng 1 W10789393 (cntrl-elec), 202.08, 1 W10807590 (cntrl-elec), 154.22"

James G.
M/W OTR WHIRLPOOL WMHA9019HZ1 "Unit has been working since Thanksgiving. Rick at tech line says it could be interference from other things on same circuit. Unit had F-6/E-0 which is on tech sheet tech line says communication issue however unit is working during visit, cleared codes"

James G.
M/W OTR WHIRLPOOL WMH53521HZ3 Replaced door due to inner abnormalities Tested ok

James G.
DISHWASHER WHIRLPOOL WDT970SAHZ0 Replaced listed parts due to no operation Tested ok

Isidore A.
DRYER WHIRLPOOL WGD9400SW1 "Removed top, front and bottom panels, removed drum, belt and all the rollers including pulley and motor pulley. Install new motor pulley and all new parts from dryer repair kit, reinstalled panels. test dryer operation ok at this time. Note customer advised that venting is not correct has two dryers going into same vent."

Isidore A.
DISHWASHER KITCHENAID KDTM504EPA2 "Removed front panel disconnect all wiring from dishwasher and installed new wiring harness including led wire harness, test dishwasher operation ok at this time reinstalled front panel."

Jesus C.
WASHER MAYTAG MHWE550WW01 "Customer states that unit has error code. Checked unit and ran diagnostics found several error codes. Hose was place to far in the drain causing siphoning. Ran test and found the bearing on tub bad. Still need drain pump or pump not working right. Ordering parts.F-20 no water detected entering unitF-21 long drain; ordrng 1 W10250762 (tub-outer,fnt), 89.16,"

Isidore A.
OVEN KITCHEN AID KEBS277SSS02 "Removed oven from wall cabinet found lower oven thermal cutoff open installed new thermal cutoff and as preventative maintenance removed old blower and installed new cooling blower, test and checked oven calibration oven at 350 degrees F. Found oven at approximately 365 degrees F. Calibration on control is set at 30 degrees F. For both lower and upper ovens customer aware oven I’ds over 10 degrees F. Temperature"

Jesus C.
REFRIGERATOR WHIRLPOOL KRMF706ESS01 Unit is still doing same thing with new tube. Ordered a from manufactureJkSr7723481467

Isidore A.
DRYER MAYTAG MED5100DW0 "Found F4E3 venting error not verified dryer is working . Properly, no check vent errors on control, customer advised to have vent professional checked, but should try timed dry cycle for lighter loads which may have cause dryer to stop. Since there was not enough clothes to sense wet clothes."

Irvin F.
OVEN FRIGIDAIRE FFEF3003NW0 "CX says the units front left burner failed. The switch is not sending correct power. Replaced element and switch. Test, passed all ops normal."

James M.
REFRIGERATOR KITCHENAID KRFC704FPS00 Found broken wires to fill tube. Ordering new water tube assembly; ordrng 1 W11230096 (WATER TUBE ASSEMBLY)

Irvin F.
REFIRGERATOR FRIGIDAIRE LFSS2312TFP0 Replaced failed bulb. Works good. Done.

Irvin F.
WASHER WHIRLPOOL WTW5000DW1 "S225EQInstalled main control. Test components. Calibrated unit, all ops normal."

James M.
DRYER SPEEDQUEEN ADG3SRGS115TW01 Fund unit making rumbling during operation due to bad roller wheel.

Irvin F.
WASHER WHIRLPOOL WTW4816FW2 "The washer is not filling with cold water. Found the solinoid is not opening fully. Removed hose from valve, the water supply is good. Hot and cold. Installed replacement valve. Ran test passed. All ops normal."

James M.
OVEN WHIRLPOOL WOS51EC0AS Found unit with broiler fault. Also found unit to run hotter than expected dusting bake cycle due to bad probe; ordrng 1 WPW10260252 (elmnt-brol)

Irvin F.
WASHER MAYTAG MVWX500XW0 "CX says the unit is not operational. Error codes found failed main control, and bad shifter. Replaced control and shifter. Ran calibration, passed."

Irvin F.
WASHER WHIRLPOOL WTW8000BW0 "Removed power. Installed suspension. Ran calibration cycle, passed. All ops normal."

James G.
WASHER WHIRLPOOL WTW8500DC0 No show;

Irvin F.
REFRIGERATOR WHIRLPOOL WRT518SZFM00 The units upper hinge was loose. The door was floating. Tightened screws. All ops normal.

Hector Z.
MICROWAVE KITCHENAID GBD277PDS3 Duplicate call.

Hector Z.
DISHWASHER KITCHENAID KDFE304DSS0 Replaced control panel. Tested ok.

Hector Z.
WASHER MAYTAG MHW5500FW0 "The washer door is locked and the drain pump is constantly running. Set unit in diagnostic and found no error code. Also ran a quick diagnostic test to be able to open the door. Contacted the tech line and she suggested that the drain hose was too far in into the drain, also found the hot and cold water hoses were reverse. Adjusted drain hose and suggested to the customer to replace both faucet because there frozen up. SR 7723605229. Tested ok."

James G.
COOKTOP JENN-AIR CVEX4370B ordrng 1 AR141B (series 7 radiant bla)

Hector Z.
REFIRGERATOR WHIRLPOOL WRT549SZDM01 Replaced ice maker. Tested ok.

Hector Z.
DRYER WHIRLPOOL WGD92HEFC0 Replaced coils and temperature sensor (Wire harness). Tested ok. I informed to the customer that the damaged side panel (Rh) and the drum was denied by the insurance company.

Hector Z.
WASHER WHIRLPOOL WFW92HEFC0 "Replaced door bellow. Ran a quick diagnostic test, tested for leaks. Tested ok."

George Y.
WASHER WHIRLPOOL WFW94HEXR2 Installed part tested ok complete . No dents or dings cause by tech.

George Y.
DISHWASHER KITCHENAID KDTM404ESS0 Found dishwasher not washing sump motor just humming need to replace sump motor assembaly replaced part tested check out ok complete no dents or dings cause by tech.

George Y.
REFRIGERATOR WHIRLPOOL WRF535SWHZ01 Found refrigerator top of freezer center small settlement of ice remove reposition gasket retested check out ok complete no dents or dings cause by tech.

Irvin F.
WASHER MAYTAG MVWC565FW1 "No errors. All ops functions. The suspension is weak, causing poorish performance in spin. Replacing suspension. ; ordrng 1 W11130362 (SUSPENSION)"

Irvin F.
WASHER MAYTAG MVWC415EW2 "CX says unit is not completing cycles. Found error code for hi rinse water temp, and load off balance. Suspension test failed, suspension is bottoming out. Need suspension. ; ordrng 1 W10780044 (suspension)"

Erick S.
WASHER GE GTW330ASKWW Cycled unit through diagnostics and found unit with door latch error causing it not to advance in wash. Replaced door latch and reprogrammed main board. Retested it and it passed all tests with no errors. Job complete ; used 1 WH01X27954 (LID LOCK) from stock

Erick S.
WASHER MAYTAG MVWC555DW Cycled unit through diagnostics and found suds error causing it not to advance in wash. Reprogrammed main main and ran tests cycle and it passed all tests with no errors. Informed cust of soap usage. Job comp

Erick S.
WASHER WHIRLPOOL WTW8500DW "Cycle unit and found it f9e1 erro indicating pump failure. Found pump seizing causing it not to drain and have error. Replaced pump. Retested it and it passed all tests with no errors, job comp; used 1 W10876600 (PUMP-WATER) from stock"

Erick S.
RANGE GE JGBS66REKSS "Inspected unit and found unit burner tube only lighting a quarter of the way. Flame spreader causing carbon error. Removed and cleared spreader. Burner is now working as design with no errors, Aldo found display flickering. Found bad pin connector causing error. Repaired connector and secured it to main hoard. Board is now working with no errors. Job comp"

Erick S.
ICEMAKER WHIRLPOOL WRF767SDHZ "Installed new adapter on unit, retested and unit is cooling with no errors. Job complete"

Erick S.
WASHER MAYTAG MVWC416FW Cycled unit and found it with fill error causing it not to advance in wash. Found bad cold solenoid not opening all the way. Replaced valve . Retested it and it fills now with no errors. Job complete

Erick S.
REFRIGERATOR KITCHENAID KRFF707ESS01 Installed new parts on unit. Retested it and it passed all tests. Unit is now cooling. Job complete

Erick S.
REFRIGERATOR FRIGIDAIRE LGHX2636TF "Inspected door and found it leaning to the right and not closing correctly. Removed door and found cracked door cam causing error. Replaced door cam, , Retested it and door is now aligned correctly and closing with no air gaps, Job complete ; used 1 241990301 (DOOR CAM) from stock"

Hector Z.
OVEN KITCHENAID KODC304ESS00 Upper oven 20deg off calibration. Adjusted upper oven temperature. Lower oven has a open thermal fuse due to self cleaning.; ordrng 1 W11165152 (OVEN THERMOSTAT.)

Erick S.
WASHER GE GTW330ASKWW "Cycled unit and found it with drain pump error causing it not to drain. Tested pump and found it bad, replaced pump, unit is now draining and cycling with no errors. Job comp; used 1 WH23X27574 (DRAIN PUMP, ) from stock"

Erick S.
REFRIGERATOR WHIRLPOOL WRF757SDEH01 Installed new parts on unit. Retested it and it’s now cooling with no errors. Job comp

Erick S.
RANGE FRIGIDAIRE LFGF3054TD "Found installed new parts on unit. Retested it and display is now working, oven cycled and heated with no errors. Job comp"

Dane K.
WASHER MAYTAG MVWB835DW0 Upon arrival of the unit would not spin and was screeching when filling and would not get the close all the way wet. It would not spend because the door would not latch and found water valve faulty. Removed and replaced door latch and water valve and calibrated and tested unit. Unit functions normal now

Dane K.
REFRIGERATOR FRIGIDAIRE FGHF2366PF/FA Installed control and tested unit. Unit functions. Normal now

Dane K.
MICROWAVE OVEN JENN-AIR JMC2430DP01 "Removed and replaced magnetron, magnetron thermostat, and control board and tested unit. Unit functions normal now"

Dane K.
WASHER FRIGIDAIRE FFTW4120SW Installed control and lid lock and tested unit. Unit functions normal now

Dane K.
WASHER WHIRLPOOL WTW4855HW1 Installed control and calibrated and tested unit. Unit functions normal now

Erick S.
REFRIGERATOR WHIRLPOOL WRF736SDAM14 Cycled through diagnostics and found fan motor not running. Accesed motor and found very low frost pattern causing it not freeze. Motor getting voltage but not responding. amp draw indicating low charge or leak. Recommended to replace motor and recharge system for proper cooling ; ordrng 1 W10865431 (motor-evap) and 1 WPW10143759 (dryer)

Bryan D.
WASHER WHIRLPOOL MVWB835DC3 Removed and replaced the housing and drawer. Unit is functioning as designed. No dents dings or scratches caused by tech.

Bryan D.
DISHWASHER WHIRLPOOL KUDE20FBSS1 Removed and replaced control. Ran unit. Unit is now functioning as designed. Dents dings or scratches caused by tech.

Bryan D.
WASHER WHIRLPOOL MVWC200BW0 Cx states washer just continues to go into cycles by itself after the original cycle completes. RN diagnostics got no error codes ran a test cycle unit performed as designed.

Bryan D.
REFRIGERATOR KITCHENAID KUDF204EPA00 Cx states firsts is not cooling. Upon arrival unit was turned off. Told cx if unit doesn’t cool to give us a call after turning cooling on. Cx also asked for me to install knob back onto filter upon doing so found the filter housing was loose and all grades were not screwed in. Informed cx. Cx stated they. Pull not have a second visit and will be contacting pacific sales to demand unit gets replaced.

Bryan D.
DISHWASHER WHIRLPOOL WDF320PADS1 Removed and replaced UI panel. Unit is now functioning as designed. No dents dings or scratches caused by tech

Dane K.
DRYER WHIRLPOOL MDG5500AWQ Unit was not drying the clothes a timely fashion because it had a massive plant buildup in accordion style tubing behind dryer and also in customers home. Short and vent for customer and ordering ripped lint screen; ordrng 1 WP33001808 (screen)

Bryan D.
MICROWAVE WHIRLPOOL WOC75EC7HS00 Cx states panel went blank and hasn’t came back on. Removed and replaced control panel. Unit is now functioning as designed. No dents dings or scratches caused by tech.

Bryan D.
DISHWASHER WHIRLPOOL WDF320PADS1 Removed and replaced UI panel. Unit is now functioning as designed. No dents dings or scratches caused by tech

Aaron B.
OVEN WHIRLPOOL WFG320M0BW2 "Replaced the oven igniter tested unit , ops normal at this time"

Dane K.
REFRIGERATOR GENERAL ELECTRIC GSS25GSHJCSS Unit needs new cover ; ordrng 1 WR49X10251 (cover assembly ff inlet)

Billy J.
REFRIGERATOR WHIRLPOOL JS48PPDUDE Cx stated bestbuy came and fixed unit job complete

Dane K.
WASHER GE GTW330ASK Upon arrival the unit would not wash. Found control not responding. Unit needs new control ; ordrng 1 WH18X28176 (CONTROL )

Billy J.
DRYER WHIRLPOOL MGD6000AG1 upon arrival removed and replaced water valve retested job complete

Aaron B.
DRYER MAYTAG MGDC215EW2 "Unit timer wasn’t advancing, replaced the timer tested operating normal now"

Aaron B.
M/W OTR MAYTAG MMV4206FZ5 "Replaced the mag and diode , tested ops normal now unit heats good now"

Aaron B.
REFRIGERATOR WHIRLPOOL WRS571CIHW00 the oven door was off of the range Both the left and right hinges replaced them both reinstalled the door operating normal now

Bryan D.
REFRIGERATOR KITCHENAID KSC24C8EYY02 Cx states after last visit the fridge stopped cooling. Inspected unit and found compressor not running. Removed Nd secured connection at start device and compressor started. Then stopped running again. Grabbed a start device from truck and compressor still not starting. Ordering compressor motor was not pulled. ; ordrng 1 W10309988 (compressor)

Bryan D.
REFRIGERATOR WHIRLPOOL WRF560SEYM00 C states water is leaking from ice maker. Found ice maker is leaking. Ordering ice maker; ordrng 1 4211173 (sub 4317943)

Aaron B.
REFRIGERATOR WHIRLPOOL WRX735SDHZ01 "Unit compressor has a louder than normal ring buzzing noises , to correct issue needs a new compressor ordered part; ordrng 1 W11209866 (COMPRESSOR ) and 1 WPW10143759 (dryer)"

Aaron B.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 "No lights in the refrigerator or freezer sections , ordered per service flash , ordered parts; ordrng 1 W10830288 (cntrl-elec)"

William L.
REFRIGERATOR WHIRLPOOL WRX735SDHV00 "found ice jambed & broken water filter cover, Replaced ice maker, ordered broken water filter housing cover & water valve.; ordrng 1 W11043013 (valve) and 1 WP67006331 (cover-filt), used 1 WPW10300024 (ICEMAKER) from stock"

William L.
WASHER WHIRLPOOL WTW8600YW0 "found water flow overflowing fabric soften dispenser, ordered water valve & dispenser parts, adjusted valves on wall didn’t help, ; ordrng 1 W10853723 (valve) and 1 WPW10136371 (bezel) and 1 WPW10172146 (dispenser)"

William L.
WASHER MAYTAG MVWC565FW1 "leveled legs on floor, ran self diagnostics, tested ok, instructed cx on loaded clothes & balancing loads."

William L.
WASHER WHIRLPOOL MVWB850YW0 "Found main bearing completely failed, replaced bearing with bearing rebuild kit, ran spin test, ran self diagnostics, unit operating as designed."

William L.
REFRIGERATOR WHIRLPOOL WRS315SDHZ00 "checked temps, temp in freezer 0 degrees, ice maker production very slow, bumped ice maker, ordered ice maker and control for unit.; ordrng 1 W11203924 (main control) and 1 WPW10300022 (icemaker)"

Tyler F.
WASHER WHIRLPOOL WTW5000DW1 Customer stated that the drain cycle is not working. Checked for error codes found long drain error code. Cycle tested unit found unit is draining and all is working good. Calibrated unit all works good at this time.

Tyler F.
REFRIGERATOR WHIRLPOOL KSSC48QTS02 Customer is having similar issue. This time the frost was under the ice bin. Found the door flap for ice dispenser is not sealing. Removed and replaced door and ice door motor tested all works good at this time.

Tyler F.
MICROWAVE IKEA IBMS1455DS00 Customer stated that the cancel button is not working. Removed and replaced it tons in interface kit. Tested all works good at this time.

Tyler F.
OVEN KITCHENAID KODE507ESS02 Customer stated that the fan is noisy in the top oven. Removed and replaced fan blade test3d all works good at this time.

Tyler F.
ICEMAKER KITCHENAID KUID508ESS0 Customer stated that unit started making ice then the controls switch back and forth. Ordering main control in stock.; ordrng 1 W11034363 (ELEC CNTRL)

Tyler F.
REFRIGERATOR KITCHENAID KRMF706ESS01 Customer stated deli drawer is not working again. Found water under the display and wire harness has corroded. Ordering door and board. Customer is aware of door time frame.; ordrng 1 W10815668 (dor-fip bl) and 1 WPW10769076 (cntrl-elec)

Tyler F.
DISHWASHER WHIRLPOOL WDT750SAHZ0 "Customer stated that the unit keeps turning on and off by itself and door handle is scratched. Ordering handle, control and console not in stock.; ordrng 1 W11037340 (HANDLE) and 1 W11087207 (cntrl-elec) and 1 W11192367 (CONSOLE)"

Tyler F.
REFRIGERATOR KITCHENAID KBSD608EBS01 Need to replace dryer but don’t have sealed system equipment in a rental.

Tyler F.
OVEN WHIRLPOOL KEMS378SSS05 Customer stated that the microwave is not working. Found error code F6E0 for communication error.

Raymond D.
REFRIGERATOR WHIRLPOOL WRS321SDHZ02 "Upon arrival unit freezing in RC, inspected and found unit at proper temps, cx has items touching liner. Instructed cx on proper use and care of unit. Unit functions as designed."

Raymond D.
WASHER MAYTAG MHW6000XW0 Upon arrival unit would not operate but would light up. Unit would not start and was unresponsive to touch. Found bad UI Center. UI parts are no longer available. Unit non repairable.

Raymond D.
REFIRGERATOR WHIRLPOOL WRS588FIHZ00 "Upon arrival unit not making ice, inspected and found broken wires on lower harness. Unit needs door.; ordrng 1 LW11037738 (STAINLESS DOOR FC)"

Raymond D.
REFRIGERATOR WHIRLPOOL WRT511SZDB00 "Upon arrival cx stated FC keeps developing frost, and another company replaced the door and it is still frosting on liner. Found large gaps from cabinet to liner. Sealed unit with adhesive. Instructed cx to call back if frost continues. Unit functions as designed.; used 1 482338 (ADHESIVE) from stock"

Raymond D.
REFRIGERATOR WHIRLPOOL KSSC42QTS00 "Air wasn’t fully defrosted. Defrosted and broke loose all ice. Tested, verified temps were cooling in RC. Unit needs to regulate to normal."

Raymond D.
DISHWASHER KITCHENAID KDTE334GPS0 Upon arrival door hitting tub when closing. Leveled feet and rectified installation issues. Unit functions as designed.

Michael M.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Removed and replaced pump assembly. Rebooted unit and unit ops but not enough water is entering the u it before wash cycle begins. Verified 1-3 psi is being delivered to unit. Advised cx to call plumber and unit now ops as designed. Advised cx not to use unit until plumbing issue is corrected. Unit ops as designed job complete

Michael M.
REFRIGERATOR WHIRLPOOL MFI2569VEB2 Cx states ice maker is not making ice.Tech found ice maker mold with ice cubes in it. Removed ice maker and found styrofoam inside ice. Attempted to replace ice maker but supplied parts do not match installed parts. Needs ice maker pn WPW10190981; ordrng 1 WPW10190981 (icemaker)

Michael M.
REFRIGERATOR KITCHENAID KRFC300ESS01 Removed and replaced door. Swapped over door seal and handle. Removed drawers and used hot water to remove all ice build up. Door now seals as designed.Job complete

Michael M.
DRYER MAYTAG MGDC215EW2 "Cx states unit will not start.Interior lights function but not spinnn g.Found thermal fuse open. Removed and rep,aced with truck stock WP3392519Unit now ops as intended. Tech found dryer exhaust vent hose collapsed and wi5 holes on it. Found large amounts of lint built up.Explained to cx that pushing unit back as far as they are is causing the hose to become smashed and popping thermal fuse. Job complete; used 1 WP3392519 (THERMAL FUSE) from stock"

Michael M.
DISHWASHER WHIRLPOOL WDF540PADT1 Unit was not filling with water. Found float switch wiring pinched in two. Repaired wire connector and u it ops as designed. Ran unit through rapid advance and all ops are normal. Job complete

Michael M.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 Cx states ice maker stopped making ice.Tech tried service test 57 and ice maker would not harvest.Removed ice maker and replaced with new. New ice maker harvested and filled. Job complete

Kenneth M.
REFRIGERATOR WHIRLPOOL KSC23C8EYW00 Installed new right rear roller. Tested unit. Unit is working. Leak checked unit one last time. No leaks found. Unit is working properly. Customer approves function at this time.

Michael M.
REFIRGERATOR JENN-AIR JFFCC72EFS00 "Cx states ice maker still is not making ice.Tech verified correct revision Verified with tech line all service test passed, unit harvest and fills. Service test 120 passed with no issues. Can manually fill mold.Ice box fan runs on manual mode. Recommended replace Dispenser User Interface W11086558; ordrng 1 W11086558 (panel-ui)"

Kenneth M.
RANGE WHIRLPOOL WFE540H0ES0 Found unit with no power due to burned junction box. Customer will need the terminal block replaced. Also found cord frayed and need replacing. Customer supplied new power cord. Ordering terminal block. Further will be made once proper power is supplied to unit. ; ordrng 1 WPW10245259 (block-term)

Kenneth M.
OVEN WHIRLPOOL WOD51EC0AS04 Unit needs control board. Ordering new control board; ordrng 1 W10842982 (cntrl-elec)

Kenneth M.
DRYER MAYTAG MEDX655DW1 Found dryer squeaking due to bad roller belt pulley. Replaced dryer repair kit wi5 truck stock and tested unit. Unit is working properly. Customer approves function at this time. ; used 1 4392065 (DRYER REPAIR KIT) from stock

Kenneth M.
DRYER MAYTAG MEDB855DC4 Found unit DOA. Found 240 volts to unit but not powering on due to bad board. Ordering new control; ordrng 1 W11158453 (CONTROL)

Kenneth M.
OVEN WHIRLPOOL WMH32L19AS1 Unit not heating. Due to to bad magnetron. Magnetron is burnt out. Also noticed wires at transformer frayed and showing wire. Ordering new transformer; ordrng 1 W10844213 (magnetron) and 1 W10847161 (transformr)

Kenneth M.
DRYER ELECTRIC WHIRLPOOL WTW4816FW Found unit continuing to click. Found lid lock faulty. Ordering new lid lock and strike. Strike damaged. Missing metal prints in back for magnetize latch; ordrng 1 W10837741 (lid strike) and 1 W10838613 (lid lock assembly)
Kegan N.
RANGE WHIRLPOOL WFG320M0BB0 "Customer stated seemed like bulb socket was broken. Inspected unit, removed old light bulb. Broken connection found, reinstalled and inserted customer’s light bulb. Test good."
Kegan N.
DISHWASHER MAYTAG MDB4949SDZ0 "Customer stated that dishwasher not working properly. Cycle stops after fill, checked float switch for continuity, test good. Ordering main control board.; ordrng 1 W10906430 (cntrl-elec)"
Kegan N.
WASHER GENERAL ELECTRIC GTW330ASK3WW "Customer stated washer not finishing cycle. Tested unit, no drain, inspected pump, overheating, no clogs. Ordering drain pump.; ordrng 1 WH23X27574 (DRAIN PUMP)"
Kegan N.
REFRIGERATOR WHIRLPOOL WRF990SLAM02 "Removed and replaced parts, tested ice and water tested good. All works good this time."

Jim S.
WASHER MAYTAG MVWC416FW1 Water valve is split on the hot water side. Replaced valve unit tested ok
Kegan N.
DISHWASHER WHIRLPOOL WDT720PADM "Customer stated unit not advancing to next cycle. Inspected unit, diverter motor clicking, not moving. Ordering diverter motor.; ordrng 1 W10537869 (diverter mtr)"

Jim S.
DRYER MAYTAG MDG5500AWW Replaced open ignitor. Found gas coils not holding. Replaced gas coils; used 1 279311 (IGNITOR KIT & BRACKE) from stock

Jim S.
DRYER MAYTAG MGD5500FW0 Unit powers up but will not start. I do not hear the relay board coming on; ordrng 1 W10774832 (switch) and 1 W10875487 (cntrl-elec) and 1 W11123147 (motor-drve) and 1 W11189141 (SWITCH)

Jim S.
DRYER AMANA NED4655EW1 Replaced thermal fuse. Unit tested ok

Jim S.
RANGE FRIGIDAIRE FFEF3003NWD Repaired burnt wire at terminal connection.

Jim S.
COOK TOP - ELEC HOT POINT RB525H4WH Replaced switch and terminal blocks. Unit tested ok

Jim S.
OVEN DACOR MCS130S Rebuilt relay board

Jim S.
N/A N/A KUIC15NHZS0 Replaced board and drain pump. Clean light stays on. Recommend running the unit for three complete cycles

Jim S.
WASHER MAYTAG MVWC416FW0 The legs are missing from the washer and Lowe’s installed it for the customer. This is a customer instruct

Jim S.
DRYER WHIRLPOOL WED4815EW1 "Replaced motor, and start relay. Upon completion found that under a load ( there was no load before due to the bad motor ) the voltage drops to zero. Customer has a bad outlet"

Jim S.
OVEN KITCHENAID KOCE500ESS06 Customer states that the oven stops heating midway through cooking and that the cooling fan motor is noisy; ordrng 1 W10861504 (blower) and 1 W11093254 (panl-cntrl) and 1 W11188752 (FUSE)

Jim S.
DRYER WHIRLPOOL WGD4800BQ2 Replaced drum supports with tensioner and belt. Unit tested ok

James G.
REFRIGERATOR WHIRLPOOL WRS321SDHZ01 Replaced listed part due to noise Tested ok