Service History 510

We serviced a

WHIRLPOOL FREEZER

Model WRS315SDHZ18

Near Moreno Valley, California 92555

Kevin

Job Details: 01/25/2025

Installed fill tube kit and used perma gum to seal around liner. All tests good.

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near Terra Bella, California 93270

J.E.

Job Details: 01/25/2025

"Installed new control board, harness, actuator, and capacitor. Retested unit now working as designed job completed."

We serviced a

GENERAL ELECTRIC DISHWASHER

Model GDT535PSR6SS

Near Fontana, California 92336

Francisco

Job Details: 01/25/2025

"Removed and replaced parts listed ,tested ops unit working properly no damage by tech"

We serviced a

GENERAL ELECTRIC WASHER

Model GTW485ASW0WB

Near Montebello, California 90640

Stephen

Job Details: 01/25/2025

"Replaced main control, latch, and belt. Programmed control. Cleaned oil from motor and transmission pulleys. Fills, agitates, drains, rinses, locks/ unlocks, and spins properly at this time. Advised customer not to use powdered detergent. Complete."

We serviced a

WHIRLPOOL OVEN

Model WFES3030RS0

Near Shafter, California 93263

Esteban

Job Details: 01/25/2025

Control board was removed and re0aced. Unit passed all test. Unit is working as intended.

We serviced a

MAYTAG WASHER

Model MVW7230HW1

Near Ridgecrest, California 93555

Brandon

Job Details: 01/25/2025

Installed new control board.

We serviced a

FRIGIDAIRE DISHWASHER

Model FFCD2413US4A

Near Huron, California 93234

Esteban

Job Details: 01/25/2025

"Trap, base and support were removed and replaced. Unit passed all test. Unit is working as intended."

We serviced a

MAYTAG: AQQ WASHER

Model MVW6500MW

Near Fresno, California 93722

Timothy

Job Details: 01/25/2025

"Checked for faults and found none. Ran a service test and found the unit passed. Looked under the unit and found oil dripping from the gearcase on the belt and cam assembly. Replaced actuator, belt, gearcase and cam assembly. Tested unit and found it operating as designed.; used 1 WPW10006384 (Belt) from stock"

We serviced a

KITCHENAID KITCHEN

Model KDPM604KPS0

Near San Luis Obispo, California 93401

Leo

Job Details: 01/25/2025

"Proceeded to remove DW from under cabinet, removed and replaced old heater element for updated one, tested unit in a normal cycle for water leaks, none was detected before reinstalling unit in its cavity, unit running properly,Job complete."

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Los Angeles, California 91042

Oscar

Job Details: 01/25/2025

"As all previously diagnoses parts and components were replaced, unit resumed normal operation and owner was present during testing."

We serviced a

MAYTAG WASHER

Model MVW6500MBK0

Near Piru, California 93040

Felipe S

Job Details: 01/25/2025

"Install the new harness, cover, motor, belt, actuator and cam kit on the unit. Retest the unit and now is working properly. Job complete"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT540HAMZ2

Near Los Angeles, California 91325

Paul

Job Details: 01/25/2025

"Unit was not washing, replaced sump and motor and is now working properly."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS00

Near Los Angeles, California 91311

Sean W

Job Details: 01/25/2025

"Replaced unresponsive ui,successfully ran ice harvest and water fill test and got no Icemaker error codes in test 56,Icemaker and fridge now working properly."

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Piñon Hills, California 92372

Cesar

Job Details: 01/25/2025

Replaced harness all tested good

We serviced a

WHIRLPOOL REFRIGERATOR

Model KRSC703HPS00

Near West Covina, California 91791

Stephen

Job Details: 01/25/2025

"Replaced scroll fan, drip pan, and UI control per service pointer # W11512766. Cleaned plugged RC drain. RC thermistor was already replaced. Unit is cooling properly at this time. Complete."

We serviced a

GENERAL ELECTRIC REFRGERATOR

Model PVD28BYNBFS

Near Patterson, California 95363

Manuel B

Job Details: 01/25/2025

Ice maker not working.install new ice maker test harvest ok.

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Phelan, California 92371

Cesar

Job Details: 01/25/2025

Replaced parts all tested good

We serviced a

WHIRLPOOL DISHWASHER

Model WDP730HAMZ1

Near Los Angeles, California 91306

Sean W

Job Details: 01/25/2025

"Installed outter gasket,dishwasher working properly."

We serviced a

WHIRLPOOL WASHER

Model MVW5035MW1

Near Phelan, California 92371

Cesar

Job Details: 01/25/2025

Replaced parts tested good

We serviced a

MAYTAG WASHER

Model MVW4505MW2

Near Bakersfield, California 93308

Aaron

Job Details: 01/25/2025

"Checked operations , the unit is set on fabric softener and an extra rinse setting , in small letters it says extra rinse tested operations. Also customer has a suds lock, which is also causing the unit not to turn off due to too much subsides not enough water and too much soap operating normal now customers properly instructed with operations."

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near San Bernardino, California 92404

Francisco

Job Details: 01/25/2025

"Cx stated unit doesnt spin. Found error code f7 e4, slider metal band slipping off. Removed and replaced slider, calibrated and tested ops 7nit working properly ; used 1 W10734521 (Slider) from stock"

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Castaic, California 91384

Felipe S

Job Details: 01/25/2025

"Replace control board, belt and cam kit on the unit. Retest the unit at the same outlet as before and voltage problem is still there. Inform this to the customer, try the test in other outlet and now unit is working properly. Job complete"

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Westlake Village, California 91361

Richard

Job Details: 01/25/2025

"Upon arrival, replaced thermal fuse thermometer thermal cut off kit checked wire harness wire harness was good did not need to replace it. Replaced user interface reprogrammed unit tested unit unit is not working as intended job"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ0

Near Turlock, California 95382

Cruz

Job Details: 01/25/2025

"Fixed- installed new parts (latch, cntrl elec) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Atwater, California 95301

Cruz

Job Details: 01/25/2025

"Fixed- installed new parts (cntrl elec, lower harness) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"

We serviced a

MAYTAG DRYER

Model MGDB835DW4

Near Los Angeles, California 91367

Richard

Job Details: 01/25/2025

"Upon arrival, inspected unit found unit making any loud screeching noise. Replaced all wheels belt and idler pulley unit is no longer screeching job complete all operations normal."

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Lost Hills, California 93249

Esteban

Job Details: 01/25/2025

Broken wire on harness. Harness was removed and replaced. Unit passed all test. Unit is working as intended.

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS05

Near Santa Clarita, California 91351

Felipe S

Job Details: 01/25/2025

"Install the new harness, door, deli ui, control board, power supply and led control. Retest the unit and now is working properly. Inform the customer they need wait at least 48 hours for ice bin full. Job complete"

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Port Hueneme, California 93041

Kenneth

Job Details: 01/25/2025

Installed drain hose and tested unit. Unit is working properly. Customer approves function at this time.

We serviced a

WHIRLPOOL DRYER

Model WED8127LC2

Near Atwater, California 95301

Manuel B

Job Details: 01/25/2025

Dryer not responding need new Cntrl board.install new Contrl board. Test work good.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN2WW

Near Huron, California 93234

Esteban

Job Details: 01/25/2025

Suspension worn out. Suspension was removed and replaced Unit is working as intended.

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW3

Near Oxnard, California 93033

Isidro

Job Details: 01/25/2025

"Installed new drain hose tested and unit is now draining without any leaks visible at this time of service, cx approved repair"

We serviced a

WHIRLPOOL WASHER

Model WTW7120HW0

Near Bakersfield, California 93312

Aaron

Job Details: 01/25/2025

"Checked the unit , bad main board 120 v to the main board , no indicator light for main board fuse means bad board replace the main board tested unit drained water out unit then started washing tested operations OK now cleared all codes. Unit is working as designed now at this time."

We serviced a

WHIRLPOOL RANGE

Model WFG550S0LZ1

Near Lancaster, California 93535

Samson

Job Details: 01/25/2025

"Replaced defective control board that wont let bake igniter stays on, unit test ok, complete"

We serviced a

MAYTAG DRYER

Model MED6200KW1

Near Phelan, California 92371

Cesar

Job Details: 01/25/2025

Failed blower has broken fin replaced blower tested good

We serviced a

WHIRLPOOL M/W OTR

Model WML55011HS08

Near Oxnard, California 93030

Isidro

Job Details: 01/25/2025

"Unit was not heating, on closer inspection found a bad magnetron, Installed new mag unit is now heating and operating as designed at this time of service"

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Hesperia, California 92345

Cesar

Job Details: 01/25/2025

"Per customer unit would not power on stopped mid cycle he had to drain water out, customer unplugged unit for 5 min and plugged back in it still did not power on so they left it unplugged. Unit has now been unplugged for several days I plugged unit in and and everything came on ran tests on all components all tested good checked connections at Acu found UI harness not fully seated this could have caused the failure. Fully seated connector tested good at this time"

We serviced a

WHIRLPOOL WASHER

Model WFW5605MC1

Near Palmdale, California 93551

Samson

Job Details: 01/25/2025

"Found clogged drain pump, removed restriction, unit test ok. Complete"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS04

Near Los Angeles, California 91304

Sean W

Job Details: 01/25/2025

"Replaced bad icemaker and successfully ran harvest,Icemaker and fridge now working properly."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ03

Near Burbank, California 91506

Oscar

Job Details: 01/25/2025

"Visual and physical inspection leaded me to a totally frosted up evaporator and a stuck I open position damper. After explaining current situation to customer, I crafted an estimate for which customer declined out of cost concerns."

We serviced a

IKEA RANGE

Model IGL730CS0

Near Stevenson Ranch, California 91381

Felipe S

Job Details: 01/25/2025

"Upon arrival found unit no heating up properly. Check the unit and found the sensor is reading 1.06 khoms, at ambient temperature, this means is good, this unit has a problem with the control board. Replace sensor and control board on the unit. Retest the unit at 400F, and after 17 minutes unit reached the temperature. Now unit is working properly. Job complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDHB08

Near Victorville, California 92395

Cesar

Job Details: 01/25/2025

Failed ice maker has power will not cycle replaced ice maker tested good

We serviced a

AMANA DRYER

Model NED4655EW1

Near Merced, California 95348

Manuel B

Job Details: 01/25/2025

No heat dryer.install new thermal cut off high limit switch.test heating ok.

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW

Near Fresno, California 93722

Timothy

Job Details: 01/25/2025

"During the service test and a spin cycle the belt would slip slightly and make a screeching sound. the customer said it is much louder that pan the sound I created. I found no faults and the unit passed its service test. The customer stated the unit stopped itself after starting and did not finish the cycle. I checked the pump, harness and capacitor which can all cause that but they checked ok. The actuator was a pre ID apart so I installed this preemptively. I also replaced the belt and cam assembly for the belt slippage."

We serviced a

ZLINE RANGE

Model RG36

Near Los Angeles, California 91311

Paul

Job Details: 01/25/2025

Unit is make a rattling noise when fan comes on to take out heat. Will need to order heat fan.

We serviced a

MAYTAG WASHER

Model MVW5035MW2

Near Moreno Valley, California 92553

Kevin

Job Details: 01/25/2025

Unit making noise in agitation. Found belt slipping a little. Removed and replaced belt. All tests good.

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Moreno Valley, California 92555

Kevin

Job Details: 01/25/2025

Unit leaking at fill valve. Removed and replaced fill valve. Tested unit. All tests good. No leaks.

We serviced a

WHIRLPOOL DRYER

Model RGD4440SQ0

Near Moorpark, California 93021

Paul

Job Details: 01/25/2025

"Door switch was broken, replaced with new one. Unit is now working properly"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ12

Near Moreno Valley, California 92555

Kevin

Job Details: 01/25/2025

Customer said temps in RC are too warm. I removed diffuser and found FC thermistor pinched and not in FC. I corrected thermistor. All tests good.

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Porterville, California 93257

J.E.

Job Details: 01/25/2025

Cycled unit and found broken harness pink wire to pump installed new harness and retested unit now working as designed job completed

We serviced a

MAYTAG DISHWASHER

Model MDB8959SKZ1

Near Los Angeles, California 91356

Oscar

Job Details: 01/25/2025

"Because of a stubborn F9 E1 error code, a new pump assembly has been replaced. Controller was reset and unit resumed normal operation."

We serviced a

MAYTAG WASHER

Model MHW8200FC0

Near Calabasas, California 91302

Richard

Job Details: 01/25/2025

On arrival inspected unit unit gave an F3E1 error code pressure switch was able to get unit opened and replaced pressure switch tested unit. Unit passed all test and is working as intended. job complete.

We serviced a

FRIGIDAIRE DISHWASHER

Model FDSP450LAF0A

Near Paso Robles, California 93446

Leo

Job Details: 01/25/2025

"Cx stated dishes are often pre-cleaned when loading DW and also rinse aid is running out too fast, instructed Cx to fill dispenser up and check for it leaking overnight, alsoCx was advised not to continue rinsing prior to loading,and also unit needs cleaning to help sensors work properly, grainy residue in sump, trap and bottom of tub, no error codes found, aerator checked and cleared, unit is running properly.Job complete."

We serviced a

GENERAL ELECTRIC WASHER

Model GFW655SPV0DS

Near Lancaster, California 93534

Samson

Job Details: 01/25/2025

"Cx complain about damp clothes after cycle, run diagnostic test with MySQL, erased error code of unbalanced that can caused this, level the unit. Errors are no longer active now. Complete"

We serviced a

WHIRLPOOL DRYER

Model WGD4950HW2

Near Thousand Oaks, California 91362

Giovanni M

Job Details: 01/25/2025

Customer let me know that the unit was not drying properly. Upon diagnosis found gas not to be hooked up properly. I uninstalled the unit and reinstalled it properly. I tested the unit after and unit is working as designed at this time.

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Los Angeles, California 91324

Sean W

Job Details: 01/24/2025

"Attempted to replace Gearcase but washplate and tub are stuck to,cant separate tub and cant replace Gearcase.called techline and was advised to replace inner tub,outer tub and washplate,will have to break washplate in order to complete repair.Sr# 7740737657Whirlpool customer service 1-800-253-1301; ordrng 1 W10902814 (Wash plate) and 1 W11219115 (Outter tub) and 1 W10811960 (Inner tub)"

We serviced a

KITCHEN AID DISHWASHER

Model KDTM604KPS2

Near Los Angeles, California 91364

Giovanni M

Job Details: 01/24/2025

CX said the unit wouldnt fill . Upon diagnosis I found the control panel to flash when unit is trying to start. No error codes. Unit needs control bords. Ordering now ; ordrng 1 W11629912 (Control) and 1 W11622495 (UI)

We serviced a

AMANA WASHER

Model NTW4516FW4

Near Azusa, California 91702

Stephen

Job Details: 01/24/2025

"Upon arrival unit was stuck in pump out mode. Reset control. Ran diagnostics. Had f7e5 error code. Cleared error code. Found belt slipping. Replaced belt. Shifter fault returned. 2 count job. Allow 1 1/2 hours. ; ordrng 1 W11481722 (Shifter) and 1 W10721967 (Splutch), used 1 WPW10006384 (Belt) from stock"

We serviced a

WHIRLPOOL OVEN

Model WFG535S0LZ1

Near Paso Robles, California 93446

Jack

Job Details: 01/24/2025

Found burner pocketing gas. Will light and not light. Burner bake and broiler kit W11126051. Burner WP9758078. Regulator W11449506. ; ordrng 1 W11126051 (Burner kit) and 1 WP9758078 (Burner) and 1 W11449506 (Regulator)

We serviced a

GE REFRGERATOR

Model ZISS420DHASS

Near Paso Robles, California 93446

Jack

Job Details: 01/24/2025

Unit is making ice a little more but temps are still high. Fresh food is at 36 to 40 degrees depending on what shelf. Freezer is at 0.01 degrees. Control shows 12 degrees and 42 degrees on control Ui display. Calling tag. Those readings are a reading yellow to white 8.5 to 13.5. Defrost drain is possibly blocked. Come back out with an extra fan motor for repair. 15213889. Compressor is really hot. Everything checked out at compressor. 220.00 for repair of clearing of drain tube and replacing fan motor. ; ordrng 1 WR60X10185 (Evap motor)

We serviced a

GENERAL ELECTRIC WASHER

Model HTW265ASW0WW

Near San Luis Obispo, California 93402

Leo

Job Details: 01/24/2025

"Mike with tech line, use diagnostic program , test locking switch not working, replace,No faults were read, order lid lock to continue repair,Ordering:WH08X37859 28765 LID LOCK Case # 15582382.; ordrng 1 WH08X37859 (LID LOCK)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KFIS29PBMS03

Near Paso Robles, California 93446

Leo

Job Details: 01/24/2025

"Enter diagnostics to test IM , test 56 came up E0Test 37 , 01Test 57, 0Test 58, 00, 10Test 59, 0 , 10Running test 45 to fill water, 02, heard valve actuating, no water was dispense to tray, tried again, same result,Test 10, 01Tracola with line assisted running a voltage reading for water valve at control board at terminals P1-1 to P3-6 and it read 4.75 volts AC, which determines a bad control board, replace Main Control board, ordering : W11380560 Control board SR # 7740809463; ordrng 1 W11380560 (Control board)"

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model GDE25EYKFS

Near Bakersfield, California 93307

Chase

Job Details: 01/24/2025

Upon arrival unit was unplugged. Plugged into power and compressor and all fans came on. Instructed cx we need unit plugged for a minimum of 24 hours to get a thorough diagnosis. I am off for the next 3 days it is okay to send another tech. ; snapped 2 QuickPics

We serviced a

FRIGIDAIRE DISHWASHER

Model GDPH4515AF1B

Near Bakersfield, California 93313

Chase

Job Details: 01/24/2025

Two separate issues. First issue is Ui is glitched out therefore having trouble starting a cycle. Secondary issue is that dispenser is having issues opening to release pod at times. Will order parts needed. ; ordrng 1 5304533992 (Ui) and 1 5304532245 (Switch) and 1 5304532199 (Dispenser)

We serviced a

GENERAL ELECTRIC REFRIGERATOR

Model GTE21GTHFWW

Near Bakersfield, California 93312

Chase

Job Details: 01/24/2025

"Deformed Fc gasket, quote for repair. Parts: $110.84Service Charge: $145.00FRL: F12 - $139.87 Additional Labor: $0.00Other: $0.00Subtotal: $395.71Tax: $0.00Job Rate: $395.71Paying in full. $395.71 CC Auth# VALXJWScheduling for next sat; ordrng 1 WR13X22762 (Gasket)"

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Bakersfield, California 93311

Chase

Job Details: 01/24/2025

Harness to pump continuing to break. Will need to replace lower wiring harness. Ordering part and scheduling cx for next Wednesday. ; ordrng 1 W11643701 (Lower harness)

We serviced a

MAYTAG WASHER

Model MHW5630HC3

Near Bakersfield, California 93312

Chase

Job Details: 01/24/2025

Rip in bellow seal causing water to leak from front on to floor. Will order and replace bellow. ; ordrng 1 W11314648 (Bellow)

We serviced a

MAYTAG WASHER

Model MFW7020RF0

Near Burbank, California 91506

Oscar

Job Details: 01/24/2025

"Visual and physical inspection were conducted and a voltage of 120V a/c has been verified at the source and all the way to main control but, its not being distributed to UI. Replacing the UI and controller recommended.; ordrng 1 W11742708 (UI panel) and 1 W11747034 (Appliance manager)"

We serviced a

KITCHENAID RANGE

Model KSGG700ESS7

Near Los Angeles, California 91403

Oscar

Job Details: 01/24/2025

"Customer states that after splatting some water by accident on top of UI, he keeps on getting the error code F2 E1, this refers to a (Stuck keypad). I ran a function testing and the unit performed fine, temperatures and preheating were within tolerance. But, because of the claim, all tagged parts and components are recommended for replacement.; ordrng 1 W11683486 (MRZ2 Control) and 1 W10759325 (Display assembly) and 1 W10901124 (Control panel)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHB06

Near Bakersfield, California 93306

James

Job Details: 01/24/2025

Unt has noise from damper during operation. Damper not closing fully. Ordering new damper. Part in stock. Will return end of day.; ordrng 1 W11236851 (Diffuser)

We serviced a

WHIRLPOOL FREEZER

Model WRX735SDHZ08

Near Bakersfield, California 93306

James

Job Details: 01/24/2025

"Ice maker not working. Ice maker bin frozen in place again and unable to be removed. Contacted techline. Same issue as before ice water leaking into bin and freezing, causing bin to be stuck inside unit. Brandon with techlineTechline system is down and cannot generate sr numbers at this time.Pressure regulator part number w10786952 40-60 psiUnit needs to be emptied and completely defrosted to remove bin and test unit.Recommended testing water pressure to ensure within 40-60 psi Ordering pressure regulator valve, water valve, and ice maker. Will bring water pressure tester on return. ; ordrng 1 W10786952 (Pressure regulator valve)"

We serviced a

GENERAL ELECTRIC RANGE - GAS

Model JGSS66SEL5SS

Near Arvin, California 93203

James

Job Details: 01/24/2025

Left side power boil burner valve stuck and wont turn past ignition. Waive doesnt close fully allowing small amount of gas to leak when. It in use. Turned off gas to unit and advised Cx to not use unit till repair can be made. Valve sent for wrong burner. Power boil valve out of stock. Ordering new valve. ; ordrng 1 WB21X25979 (Power boil burner valve)

We serviced a

KITCHEN AID DISHWASHER

Model KUDS35FXSSA

Near Bakersfield, California 93308

James

Job Details: 01/24/2025

Unit has broken wheel on back right side of lower rack. Wheel had come off and became wedged under door causing door to tilt to one side when trying to close. Quoted for new rack wheelRack wheel support W10195416VParts: $43.32Service Charge: $175.00FRL: C1 - $107.20 Additional Labor: $0.00Other: $0.00Subtotal: $325.52Tax: $0.00Job Rate: $325.52Paid in full; ordrng 1 W10195416V (Wheel support)

We serviced a

GENERAL ELECTRIC RANGE

Model JTS3000SN2SS

Near Madera, California 93636

David

Job Details: 01/24/2025

Found control not functioning and element not heating ordering control and element ; ordrng 1 WB27X36806 (Control) and 1 WB44X48685 (WB44X48685)

We serviced a

GENERAL ELECTRIC WASH/DRY COMBO

Model GUD24GSSM1WW

Near Topanga, California 90290

Giovanni M

Job Details: 01/24/2025

15584140Called tech line because unit seems to be working as designed. Cx did has the same error codes again. Being the lock and out of balance errors. Tech line is telling me to replace the lid and latch. ; ordrng 1 WH49X27330 (TOP COVER 24 - WIRE TIES) and 1 WH44X10285 (Lid) and 1 WH44X10288 (Lid lock)

We serviced a

GE WASHER

Model GTW490ACJ8WS

Near Atwater, California 95301

Manuel B

Job Details: 01/24/2025

No power at display panel ACU burn out or shorted.standpipe to low will not drain properly.instruct customer to put standpipe to 39 inches minimum.call tech support to document file15580080; ordrng 1 WH22X37217 (Main Cntrl board)

We serviced a

WHIRLPOOL LAUNDRY

Model WTW6157PB0

Near Merced, California 95340

Cruz

Job Details: 01/24/2025

Rotor bolt strip when trying to remove it from rotor- will need to order other parts to fix unit- look at pictures- ; ordrng 1 W11449841 (Gear case) and 1 W11260238 (Rotor) and 6 W11027980 (Screws)s and 1 W11510461 (Wash plate)

We serviced a

KITCHENAID OVEN

Model KGRS306BSS0

Near Camarillo, California 93010

Ian Y

Job Details: 01/24/2025

Removed previous DSI board and had new one on when I realized new board didnt have proper number of relays. Ordered the wrong DSI board. Ordered proper board and double checked I had the right main board (I do). Will be replacing both boards simultaneously. ; ordrng 1 WPW10331686 (Spark module)

We serviced a

KITCHENAID M/W OTR

Model KMMF730PPS00

Near Westlake Village, California 91361

Richard

Job Details: 01/24/2025

Upon arrival inspected unit found unit acting weird on the user interface put unit and diagnostics unit gave me no error codes but user interface was intermittently unresponsive ran a factory reset on the unit through diagnostics unit continued to perform the same issue ordering a new complete door assembly user interface is built into the doorbringing back appliance manager. Main control with me will need a second man authorization. It is a very heavy microwave and consumer has marble countertops want to be as safe as possible not hurt myself and not hurt the consumers countertops. Do you need a two job count?; ordrng 1 W11670170 (Complete microwave stainless steel door)

We serviced a

MAYTAG WASHER

Model MVWB835DC4

Near Bakersfield, California 93313

Felipe S

Job Details: 01/24/2025

"Upon arrival found unit no responding to any commands to the user interface. Check the control board and ACV is present and normal, check the led light and is blinking normally, check the ui connector and has properly continuity and is 5 DCV and the connector J18. Reconnect the ui and now is working and let me goin through diagnostic. Found an error code F6E3, this about ACU cannot hear UI. Erase the codes, and flow all the steps on the tech sheet, run a diagnostic cycle and unit now is working properly. After test try to run a clean washer cycle and ui doesnt respond again. This unit will need new UI; ordrng 1 W11120178 (Ui) and 1 W11400681 (Control board)"

We serviced a

AMANA RANGE

Model AGR4203MNB0

Near Bakersfield, California 93305

James

Job Details: 01/24/2025

"Pvr stated that unit should be vacant. Unit is not vacant. Resident did not know about repair and did not have pop. Office to confirm with land lord that unit is occupied and that resident is made aware of repair needing to be made to oven. Repair to be rescheduled after confirmation. ; saved tckt , states that autho needed"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF550SAHS

Near Bakersfield, California 93301

Brandon

Job Details: 01/24/2025

Unit is filling longer than intended. Water overflowing. Issue could be flowmeter or board related. Ordering both.; ordrng 1 W11226325 (Vent with flow meter)

We serviced a

FRIGIDAIRE RANGE - GAS

Model FCFG3083ASA

Near Bakersfield, California 93307

Brandon

Job Details: 01/24/2025

Cx received bad conversion kit. Several burners are not functioning properly despite have proper orifices. Reordering kit. Plus regulator.; ordrng 1 GRLP5 (Conversion kit) and 1 316091711 (Regulator)

We serviced a

JENN-AIR REFRIGERATOR

Model JBRFR36IGX10

Near Bell Canyon, California 91307

Ron

Job Details: 01/24/2025

Tech was assigned as a helper;

We serviced a

ELECTROLUX DRYER

Model EFMG527UIW0

Near Templeton, California 93465

Jack

Job Details: 01/24/2025

E41 code. Customer wants to wait. I will check in with them on Tuesday. ; schdld next appmnt for 1/28 TUE !

We serviced a

WHIRLPOOL DRYER

Model MGD8630HC3

Near Bakersfield, California 93311

Randy

Job Details: 01/24/2025

"Unit is loud over time during use. Tested and confirmed noisy. Unit requires multiple parts to quiet. Drying is taking too long. Cx has had vent cleaned. Replacing thermistor n cut off as well ; rqstng P&A on 1 W11364931 (Motor), ordrng 1 WP697772 (Wheel), rqstng P&A on 1 WPW10211911 (Housing) and 2 W11676493 (Seal)s and 1 W11396709 (Thermistor) and 1 WP8573713 (Cutoff) and 1 W10906551 (Housing out)"

We serviced a

GENERAL ELECTRIC DISHWASHER

Model GDT645SYN4FS

Near Bakersfield, California 93311

Randy

Job Details: 01/24/2025

Unit leaks from seal during use. Needs service kit. ; ordrng 1 WD19X25700 (Wash pump service kit)

We serviced a

JENN-AIR DISHWASHER

Model JDB9800CWP2

Near Malibu, California 90265

Giovanni M

Job Details: 01/24/2025

CX is getting a F10E3 error code. Called techline and they said that the fan can cause the UI to act weird. Ordering the vent fan now ; ordrng 1 WPW10469574 (Vent)

We serviced a

JENN-AIR REFRIGERATOR

Model JBRFR30IGX00

Near La Cañada Flintridge, California 91011

Oscar

Job Details: 01/24/2025

"Visual and physical inspection were conducted and because the lack of men power and the difficulty level on achieving successful completion results, I have reached out to Erick and related all the information of my witnessing, and because the Freezer unit is going to be replaced, he recommended keeping this ticket opened until we replace the freezer and performed the refrigerators repair.Note, part sent by Jenn air to customer, was left with customer.; saved tckt"

We serviced a

WHIRLPOOL RANGE

Model SF367LEKQ2

Near Victorville, California 92392

Cesar

Job Details: 01/24/2025

"Replaced parts listed I was not able to remove 2 of the electrodes from old burner base screws are stuck, broil now working good but bake does not ignite rerouted for bake burner electrodes and screws for electrode ; ordrng 1 8190618 (Bake burner) and 2 WP8523793 (Electrode)s and 2 WP8273062 (Screw)s"

We serviced a

MAYTAG WASHER

Model MVWP575GW0

Near La Puente, California 91744

Stephen

Job Details: 01/24/2025

"Ran diagnostics. Found basket hub slipping, gear case leaking oil on splutch, capacitor, belt, and shifter, agitator is stuck on splines. 3 count job. Allow 2 hours. ; ordrng 1 W11454738 (Gear case) and 1 W11418231 (Agitator) and 1 W10528947 (Hub) and 1 W10721967 (Splutch) and 1 W11212745 (Shifter) and 1 W11213879 (Belt) and 6 WP8533953 (Screw)s"

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Orcutt, California 93455

George

Job Details: 01/24/2025

Installed parts tested check out ok agitator is strip need this part.; ordrng 1 W11550891 (Agitator)

We serviced a

WHIRLPOOL MICROWAVE

Model JMW3430WS02

Near Nipomo, California 93444

George

Job Details: 01/24/2025

Found oven with f6e8 error parts no longer available paid for se4vice with I wallet complete; ordrng 1 W10292566 (Control) and 1 W10319321 (Ui) and 1 W11033422 (Interlock)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRQA59CNKZ

Near La Puente, California 91744

Stephen

Job Details: 01/24/2025

RC LED flickering. Needs W11470191 module per service pointer # W11755210. S-code S194AQ parts & labor. 2 count job. Allow extra time. ; ordrng 1 W11470191 (LED module)

We serviced a

WHIRLPOOL WASH/DRY COMBO

Model WGTLV27HW2

Near El Monte, California 91731

Stephen

Job Details: 01/24/2025

Ran diagnostics. Has f8e1 error code. Found cold water valve stuck closed. 2 count job. Allow 1 1/2 hours.; ordrng 1 W11222849 (Valve)

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KPS2

Near Highland, California 92346

Rod

Job Details: 01/24/2025

"ConfirmedNo action from controls after ui o interaction just goes dead then just clicks relays in control..no fault codes suspect faulty ui , main control and machine control shorted..ordering to have parts necessary to repair properly.; schdld next appmnt for 2/7 FRI 11-2"

We serviced a

WHIRLPOOL M/W OTR

Model WMH31017HZ08

Near Yucaipa, California 92399

Rod

Job Details: 01/24/2025

"Heats for about 2 minutes just fine with no lower runningConfirmed seems blower shorted causing shorting of one or both blower relays and fan capacitor. ; ordrng 1 W11552018 (Relay board) and 1 W11405832 (Capacitor, blower motor)"

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Perris, California 92571

Kevin

Job Details: 01/24/2025

Unit not draining. I found broken wire in lower harness causing no voltage to drain pump. Ordering lower harness and clip to support harness per service pointer. ; ordrng 1 W11643701 (Harness) and 1 W11284522 (Clip)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model LFTR1835VF

Near Fontana, California 92335

Francisco

Job Details: 01/24/2025

He led unit found timer stuck on defrost found 120 vac on orange wire but not outputting 120 vac on red wire. Bypassed with jumper unit started right up unable to advance manually. Ordering timer ; ordrng 1 5304526183 (Timer)

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706EBS05

Near Hesperia, California 92345

Brian

Job Details: 01/24/2025

"Sr#7740808637 spoke with Techline. Techline advised to replace water valve, facia heater jumper, and updated adapter kit. Parts ordered ; ordrng 1 W10864519 (Adapter) and 1 W10673048 (Faciia Heater jumper) and 1 W11482383 (Dual Valve)"