"Because of a heavy leaking at the doors bottom, a new bellow gasket has been replaced."

Unit not cooling in both compartments. I found locked up compressor causing no cool. Removed and replaced compressor. Vacuumed system down and charged with r600. All tests good.

Installed new lid retested unit now working as designed job completed

"Removed and replaced compressor. Pulled vacuum, recharged system, inspected for leaks and found none. Unit is now cooling job com"

Installed part tested check out ok complete no dents or dings cause by tech.

"Middle spray arm asm came apart, replaced it with a new one, operations ok now at this time"

"Installed difuser, tested, unit functions as designed."

"Used water tube, cleared drain, tested, unit functions as designed."

Installed brackets.

Light switch arrived broken for client. Not cosmetic issue. Functional problem. Removed and replaced switch now working as designed

Cleared plugged defrost drain. Heater and thermal fuse ohm out ok. Drain is flowing properly at this time. Unit is cooling properly at this time. Instructed customer to allow 24 hours before loading food. Complete.

Heating element was removed and replaced. Dryer is working as intended. Job completed

Installed drain hose. All functions tested okay no leaks found after parts installed. Unit working as designed. Call complete

Air channel going to fresh food section was iced up not allowing air in removed ice air is flowing properly Job complete

Installed part tested check out ok complete no dents or dings cause by tech.

Installed start relay and tested unit working as designed

Found broken door switch replaced switch tested unit dryer is tumbling and heating properly Job complete

"Unit was not draining, had error code F9E1, F8E6. Checked drain pump and noticed cable had came off. Reinstalled connection and unit began to drain. Cleared out error codes, calibrated unit, and ran diagnostics. Unit is now working as designed, job complete"

"Checked the unit , dampener is noisy , replaced the dampener asm , tested ops ok now at this time"

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

Replaced thermal cutoff and thermal fuse.dryer working properly.

Cycle unit and found unit working as designed informed customer of finding. Job completed

Icemaker bail arm was making contact with tray and causing it to stop the harvest. Replaced with preID icemaker. Unit now working as designed.

Ice maker was removed and replaced. Unit is working as intended. Job completed.

Thermostat was removed and replaced. Unit is working as intended.

Removed and replaced pump n motor n sensor. Tested now working as designed.

"Checked the unit the slider was separating, replaced the slider , customer has coins in basket, tested ok now at this time"

Installed new UI and retested unit now working as designed job completed

Replaced cracked blower wheel and motor mount. Tested after repair all ok. No more loud noise.

Fixed- found ice maker to be slowing down on ice production- temperature @ 2°- installed new (ice maker) ice maker harvest and water filled mold- allow 12-24 hrs for ice production- customer ok repair

Swapped out unit control board. Unit is no longer shutting off prematurely. Job complete.

"Installed belt, rollers and idler, tested unit functions as designed."

"JB out 11/10/23.Customer states unit shakes and vibrates badly every cycle, during wash (tumble) portion and especially in the spin portion of the cycle. Verified unit has been installed on the CORRECT pedestal intended for this model Washer/Dryer combo.Also verified Unit is level and the shipping bolts have been removed. However, the installer neglected to remove the (2) Brackets on the rear of the washer as outlined in the provided Installation Instructions.Ran diagnostics, specifically test #11 (Spin) without clothes in the wash tub and verified proper spin operation. No shaking even at highest spin speed.Spoke with Corey at GE TAG WHO CONFIRMED THE TWO BRACKETS ON THE REAR OF THE MACHINE SHOUD BE REMOVED AND THE (4) washing machine feet SHOULD BE INSTALLED TO INCREASE STABILITY. INSTALLER DID NOT INSTALL THESE FEET AND ARE NOT HERE. REFER CUSTOMER TO INSTALLER TO RETURN AND CORRECT INSTALLATION.PER GE, THE 4 Bolts and Spacers MUST BE REINSTALLED BEFORE TILTING OR TIPPING WASHER OR SUSPENSION SPRINGS WILL BECOME DISLODGED. Installer must return to correct the installation. The four missing washing machine feet must be installed between the washer, and the pedestal tightened between the washer and pedestal and the lock that must be tightened as well for each of the 4 feet. Installation corrections are not covered under the General Electric, manufactures warranty, and the responsibility for correctly Escalation falls upon the installer. No charge to the customer. No Parts used. Job complete."

Fixed- installed new parts ( 2 cntrl elrc) all lights are now working per design- customer ok repair

Install the new glass on the unit. Job complete.; used 1 WPW10188327 ( Glass) from stock

Replaced burner cap and flame spreader.cooktop working properly.

Nut spanned and gear case were removed and replaced. Unit is working as intended. Job completed.

Installed new mullon. Also tighten all handles. Job complete.

Upon arrival found unit with rack falling down this because one of the wheels on the left side is broke. Replace the adjuster kit on the unit. Retest the rack and now everything is working properly. Job complete.

Replaced valve. Refrigerator operating as designed. No leaks.

"Returned, replaced defective partsdesigned operation was restored"

"Found the unit, not cooling, verify problem compressor not working, replaced compressor,service valve and cntrl-elec, charge nitrogen not verify leaks, make a vacuum, charge refrigerant 4.50 oz R134a, check compressor,condenser and evaporator fan motors unit work normal"

Found long fill code tested unit found failed #1 cold water valve has power not fully opening. Replaced valve all tested good ; used 1 W11316256 (Valve) from stock

"Found actuator and drive pulley bad replaced tested working properly ; used 1 W10913953 (ACTUATOR), and 1 W10721967 (DRIVE PULLEY) from stock"

Replaced all selected parts Unit working properly as required

"Replaced cooktop, tested all burner functions, unit operating as designed."

"Fixed- customer states turn table drive shaft pop off when plate is rotating- I found that turn table drive wasnt seated properly causing turn table drive shaft to pop out, I then reseated drsive shaft properly, tested, turn table drive shaft is not popping out when rotating- customer ok repair"

Fixed- found oven door glass to be shattered- installed new part (front glass) look at pictures - door is opening/closing as designed- customer ok repair

Cycled unit and found bad connection to control board causing unit to fail. Secure connection to re-tested unit now working as designed. Job completed.

Installed freezer door and tested unit. Unit is working properly. Custoner approves function. Customer had door delivered to there house and that door was damaged. So used door brought out by us.

"There is two screws sticking out beyond cabinet. Pic provided. Customer has handy man install new outlet for dishwasher. Screws are from outlet installation, not dishwasher install. Unit operating as designed. Job complete."

"Installed new drive pulley and belt, tested unit and working as designed"

Found lid lock bad replaced tested working properly

Installed parts tested check out ok complete no dents or dings cause by tech.

Found the unit does have a f8e1 error code stored. I verified the screens and they are clear. There are no obstructions in the pressure hose or sensor. I ran several diagnostic cycles and last I stated a load and no error code present and it is going through the cycle. Possibly reset after performing a diagnostic cycle. I removed the error code stored and all functions are testing properly. Job completed.

Ran cycle and unit did not heat up. Found open thermostat. Replaced the thermostat and ran cycle. Unit passed all tests and is operating as designed.; used 1 W10909685 (Thermostat) from stock

"Unit was not cooling replaced compressor and unit was still giving me issues. Replaced filter dryer and unit began to work as designed. Filter dry had clogged, repositioned and unit worked as designed, temperature is dropping. Job comeplete"

Replaced thermal fuse. Unit working properly as required

Removed and replaced dispenser. All tests good.

Replaced motor. Unit tested ok

Customer states the unit is leaking from underneath. Found the fill hose was loose at the boot. Reset and Secured with a zip tie.

"Upon arrival found unit with error codes, F31 and F26, this codes are for out of balance. Check the unit and unit has a bad movement every single time when the unit is on spin mode. Check the unit and found the installers. They never remove the brackets on the back chassis of the unit. remove the brackets for transportation. Retest the unit on spin mode, erase the error codes. Unit passes all the test at this time. Job complete"

Replaced new parts. Dryer operating as intended at time of service.

Installed motor capacitor and actuator now unit will not start. Removed and replaced harness tested all works good at this time.

"Replace damaged water line, tested unit and is working properly, no leaks found at this time."

Removed and replaced suspension rods and tested unit. Unit functions normal now

"Replaced struts, board, and dispenser housing"

Found range door falling apart replaced glass retested check out ok complete no dents or dings cause by tech.

Found dryer cycling short. Removed the vent system on dryer cycle normalNOTE: Dryer works ok. is in a second floor. Buildings vent system is the problem. Not dryer

Replaced defuser checked heater and thermistor and passed test defrosted evaporated unit is worcking properly

"Removed and replaced timer ass,belt. Pulled vaccum, and finished charging system. Unit is now cooling and passed all tests at the time of service. Job comp"

Found cam making noise replaced belt actuator and cam tested working properly

Found a pressure system fault upon inspection. The pressure hose was loosely fitted to the control. I reconnected and ran the pressure test. Unit is now filling without issue and progressing through cycles.

Heater was not heating. Voltage was fine. Checked connections at heater and found loose wire. Reconnected and tested. Unit is now heating.

Ice chug module was removed and replaced. I believe it was A defective parts not sealing properly freezing the water line. Unit is working as intended. Job completed.

Replaced console. Tested unit. Unit operating as designed. Job complete.

Install a new repair kit. Dryer works OK now.

Installed door and tested unit. Unit is working properly. Customer approves function at this time.

Found a loose connection at the hose that goes from the tub to the pump. I reinstalled the hose and tested fully. No leaks found. All functions tested ok and no error codes stored. Job completed.

Installed new dispenser assembly per techline instructions. Unit now working as intended.

"Upon arrival found unit with error code F0E5, this about out of balance. Erase the code and check the functionality of the unit. The unit is now working properly. Inform the customer how to operate the unit correctly. Job complete"

Customer had pic of registration date. Took pic Unit threw err code. Found bad control. Removed and replaced control board. Tested now working as designed

"Unit had error code F6E1 Acu was not communicating with unit, replaced UI Board and ran diagnostics mode. Unit is now working as designed. Job complete."

"Not powering on. Found power cord connector terminal backed out. Reseated terminal into connector. Locks/ unlocks,fills,agitates,,dispenses,and spins properly at this time. Complete."

Foot pedal broken causing unit to fall off. Replaced for pedal and tested. Unit is working properly.

Found customer having issues to start unit. Referred to sp W11679421. Unit working properly.

Replaced repair kit. Unit working properly as required

Checked unit found unit heating and venting properly. Dark vent is normal due to heat coming out of there. Recommended switching to rigid hose for venting

Installed part tested check out ok complete no dents or dings cause by tech.

Found refrigerstor not making replaced Icemaker retest ok complete no dents or dings cause by tech.

"Customer says the ice is not dispensing from the bucket. ice paddle is not responding consistently. Replaced the paddle. Restored power test passed. All ops normal"

"Installed new thermostat and adaptive defrost, tested unit,working as designed"

Installed the new control board as well as the Thermistor

Installed new damper air duck assembly. All functions tested okay. Call complete.

"Unit was not making ice, ice maker was in the off position but when ran diagnostics to fully harvest cubes came out small. Looks like a water valve issue because ice cubes were small. No error codes as well. Unit should be working as designed. Job complete"

Moisture building up under the cabinet. The exhaust vent from the bower housing was off. The screw that is normally in place to keep it from moving was not present. Placed the vent in the proper position and installed a screw to keep it from moving

Replaced leaking water valve. Unit tested ok

"Installed new water filter and tested, this water filter is working, unit working as designed"

Rotor retainer is missing. Replaced rotor and slider. Tested unit and found it operating as designed.

Ice maker was removed and replaced. Unit is working as intended now. Job completed.