Service History 478 - Appliance Repair Specialists

We serviced a

AMANA DRYER

Model NED4655EW1

Near Manteca, CA 95336

Martin R

Job Details: 02/26/2024

Found bad thermal fuse, replaced fuse, tested unit, dryer is heating and tumbling per design job complete.

We serviced a

MAYTAG WASHER

Model MVW7230HC1

Near Arroyo Grande, CA 93420

Paul V

Job Details: 02/26/2024

Ran unit through test. Issue with water valve. Removed existing water valve. Installed new water valve. Test ran unit. Unit operating as designed.

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Oak Park, CA 91377

Ron H

Job Details: 02/26/2024

Unit was not level, Leveled unit. tested unit and unit is working properly.

We serviced a

MAYTAG REFRIGERATOR

Model MSS25C4MGZ06

Near Riverside, CA 92503

Ruben O

Job Details: 02/26/2024

"Replaced faulty Icemaker assembly it was making a loud popping noise and not making ice. Tested new ice maker after replacement, all ok."

We serviced a

KITCHENAID VENT HOOD

Model KVUB600DSS5

Near Riverside, CA 92503

Ruben O

Job Details: 02/26/2024

Found the grease filters installed upside down by installers. Showed customer how to install them properly. Unit ok.

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Riverside, CA 92503

Ruben O

Job Details: 02/26/2024

"Replaced slider plastic was separating from the metal. Replaced broken door strike. Replaced broken door latch. Leveled the washer as it was leaning backwards. Tested after repair all ok.; used 1 W11700916 (Door latch), 1 W11457841 (Door strike), and 1 W10734521 (Slider) from stock"

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW0

Near Los Angeles, CA 91306

Sean W

Job Details: 02/26/2024

Washer had defective drain pump. Replaced drain pump. Washer working properly.

We serviced a

WHIRLPOOL RANGE

Model WFG505M0MS0

Near Ontario, CA 91761

Tyler

Job Details: 02/26/2024

Customer stated that the oven originally would not heat. Previous company came out and changed wire harness then had to return 3 times because it was tripping the breaker. Found harness was installed incorrectly and was pinched between panels. Fixed harness and preheated oven to the 350. Unit is working to specs. Tested all works good at this time.

We serviced a

AMANA DRYER

Model NGD4655EW2

Near Duarte, CA 91010

Andy

Job Details: 02/22/2024

"Drum not turning, replaced roller kit and tested unit working properly."

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near West Covina, CA 91791

Andy

Job Details: 02/22/2024

"Makes noise and not washing, replaced cam and actuator tested unit working properly."

We serviced a

MAYTAG WASHER

Model MVW7230HC1

Near Bakersfield, CA 93306

Chase

Job Details: 02/22/2024

Cx complaint that unit stopped working after running a clean cycle. Found f6e3 code. Cleared error code and re secured all connectors back into acu. Programmed main control and calibrated. All ops now working as designed.

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Bakersfield, CA 93306

Chase

Job Details: 02/22/2024

Found that hi limit connector came loose not allowing heat to cycle on. Re connected and secured. All ops now heating and running with no issues.

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS05

Near Hanford, CA 93230

Enrique

Job Details: 02/22/2024

"Ice maker stopped producing ice. E5- timed ice making. Replaced ice maker, ran test 57 & 45. Operating as designed. No leak."

We serviced a

JENN-AIR FREEZER

Model JBZFR18IGX00

Near Los Angeles, CA 91364

Felipe S

Job Details: 02/22/2024

Upon arrival found unit no producing any ice. Check the unit and found the ice maker is broken and on bad position. This unit will need new ice maker. Replace the ice maker. Retest the unit on tests 120. And unit passes all the test at this time. Informed of the customer they need a way at least 24 hours for the ice production. Job complete

We serviced a

GENERAL ELECTRIC WASHER

Model GFW850SPN1RS

Near Madera, CA 93636

Irvin

Job Details: 02/22/2024

"The front load washer was not dispensing properly. The unit is not operating properly. Installed smrthq found the unit has several error codes, and was in need of a software update. This update corrected the dispenser issue. While testing found the valves were not dispensing properly the screens had sediment causing poor flow, corrected by removing the buildup. Restored power retest valves, passed. All ops normal. DONE."

We serviced a

MAYTAG WASHER

Model MVW6230HW0

Near Madera, CA 93637

Irvin

Job Details: 02/22/2024

Agitator is cracked in several spots causing clothes damage. Installed replacement agitator. Done. All ops normal. Calibration passed.

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW3

Near Ojai, CA 93023

Isidro

Job Details: 02/22/2024

"I found a unresponsive Bad drain pump , I installed and secured new drain pump, tested and unit is now operating as designed, customer approved repairs and service"

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Bakersfield, CA 93309

James

Job Details: 02/22/2024

Lid lock broken. Replaced lid lock and cleared fault codes.Tested ok

We serviced a

WHIRLPOOL WASHER

Model WTW5105HW1

Near Taft, CA 93268

James

Job Details: 02/22/2024

Repaired broken wires to drain pump.Cleared fault codes.Tested ok

We serviced a

WHIRLPOOL WASHER

Model WFW5605MC0

Near Bakersfield, CA 93306

James

Job Details: 02/22/2024

Washer has long drain error. Replaced drain and tested. Unit working as intended.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ08

Near Tulare, CA 93274

J.E.

Job Details: 02/22/2024

Cycle unit and found bad connection to defrost heater Causing cooling issue, Secured connection to defrost heater and retested unit, now working as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ02

Near Lancaster, CA 93534

Jonathan

Job Details: 02/22/2024

"Found defective freezer door. Fixed freezer door, tested unit and is working properly"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT1814WW

Near Palmdale, CA 93550

Jonathan

Job Details: 02/22/2024

Found defective door seal. Fixed seal. Tested unit and is working properly.

We serviced a

MAYTAG DRYER

Model MGD6200KW3

Near Los Angeles, CA 91605

Leon

Job Details: 02/22/2024

Cx states that unit is making noise during spinning After running diagnostic test find that rear panel was attached to airflow duct, removed unit and organized duct and wire Unit working properly as required.

We serviced a

GENERAL ELECTRIC DRYER ELECTRIC

Model GFD85GSPN1RS

Near Castaic, CA 91384

Randy

Job Details: 02/22/2024

Complaint unit wont dry. Installed on Tuesday. Found unit with crushed vent. No airflow causing long dry times. removed unit and made sure has airflow. No more crushed vent. Customer checked vent now Has airflow unit working as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ08

Near Riverside, CA 92507

Robert U.

Job Details: 02/22/2024

Found the upper right side of the freezer door gasket not sealing. I heat treated the door gasket and also removed the ice. The door is now sealing after heat treatment to the gasket. I recommend leaving the door closed for the next hour or two. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW7120HC1

Near Baldwin Park, CA 91706

Andy

Job Details: 02/21/2024

Makes noise when agitating. Replace slider and tested unit working good.

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW3

Near Monrovia, CA 91016

Andy

Job Details: 02/21/2024

"Not spinning, repaired lid switch due to not engaging. Tested unit, working properly"

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near San Gabriel, CA 91775

Andy

Job Details: 02/21/2024

"Leaks, repaired bleach dispenser due to not aligned with tub. tested unit working good no leaks"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF577KPS02

Near Ridgecrest, CA 93555

Brandon

Job Details: 02/21/2024

Damper control was making excessive noise upon arrival. Used pre-ID part to repair. Unit is now working as designed.

We serviced a

WHIRLPOOL DRYER

Model LDR3822PQ3

Near Los Angeles, CA 91367

Felipe S

Job Details: 02/21/2024

"Upon arrival, according with customer unit is taking too long in order to dry the clothes. Check the unit and found lint clogging the ventilation system. Remove the lint, additional the moisture sensor fell into the drum. Re-adjust the moisture sensor. Retest the unit and our unit is working properly. Inform the customer as well. They will try to keep clean the ventilation system from the house. Job complete."

We serviced a

GENERAL ELECTRIC DISHWASHER

Model GDT550PGR3WW

Near Oceano, CA 93445

George

Job Details: 02/21/2024

Found dishwasher spray arm off, repositioned and retested on a fill wash and drain, unit functioning as design.

We serviced a

MAYTAG WASHER

Model MVWC465HW3

Near Madera, CA 93638

Irvin

Job Details: 02/21/2024

"The washer has the new style actuator. It was not in place. The washer had no errors. Replaced the actuator. Restored power, ran components test, passed. All ops normal. DONE."

We serviced a

WHIRLPOOL DRYER

Model WGD75HEFW0

Near Bakersfield, CA 93309

James

Job Details: 02/21/2024

Installed dryer repair kit.Tested ok

We serviced a

FRIGIDAIRE DISHWASHER

Model GDPH4515AF0A

Near Bakersfield, CA 93313

James

Job Details: 02/21/2024

Pump motor not running. Replaced defective pump motor. Tested ok

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW3

Near Livingston, CA 95334

Manuel B

Job Details: 02/21/2024

Error code f0e1 lid lock. And agitator not engaged adjust belt and pulley. ran diagnostic test after all cycles work.

We serviced a

MAYTAG DRYER

Model MED6630HW0

Near Modesto, CA 95358

Martin R

Job Details: 02/21/2024

Found bad element replaced element tested unit dryer is heating and tumbling per design Job complete.

We serviced a

MAYTAG DRYER

Model MGDX655DW0

Near Los Angeles, CA 90065

Oscar L

Job Details: 02/21/2024

"Because of a broken latch issue, A new latch assembly was replaced."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ00

Near Simi Valley, CA 93063

Paul M

Job Details: 02/21/2024

"Unit was not dispensing ice and producing water. Replaced water valve, unit is working properly."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHV06

Near Riverside, CA 92503

Ruben O

Job Details: 02/21/2024

Reinstalled the right hand door handle and tightened screws for the left hand door handle. Secured screws with loctite. Unit ok after repair.

We serviced a

MAYTAG DRYER

Model MGDB765FW

Near Beverly Hills, CA 90210

Samson O

Job Details: 02/21/2024

"Calibrate unit, test all components. Complete. Unit heat up good now"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS05

Near Los Angeles, CA 91303

Sean W

Job Details: 02/21/2024

Ui displaying E5 icemaker error code indicating a defective icemaker. Replaced icemaker. Successfully ran an icemaker water fill test. Replaced icemaker. Fridge working properly.

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Bell Canyon, CA 91307

Sean W

Job Details: 02/21/2024

Replaced torn belt.washer now working properly.

We serviced a

MAYTAG WASHER

Model MVW6230HW2

Near Riverbank, CA 95367

Andrew H

Job Details: 02/20/2024

Capacitor faulty. Leaking. Replace W11162560. Tested out okay. Operating as designed. ; used 1 W11162560 (Capacitor) from stock

We serviced a

WHIRLPOOL WASHER

Model WTW8120HW

Near Covina, CA 91722

Andy

Job Details: 02/20/2024

"Makes noise, repaired screw on rotor tested unit working properly"

We serviced a

AMANA DRYER

Model NGD4655EW4

Near Covina, CA 91722

Andy

Job Details: 02/20/2024

"Drum not turning, broken belt, replaced roller kit and tested unit working properly"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT518SZFM02

Near Arcadia, CA 91007

Andy

Job Details: 02/20/2024

"Not cooling, defrosted drain line and tested unit working properly"

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KPS1

Near Kernville, CA 93238

Brandon

Job Details: 02/20/2024

Unit would not drain upon arrival. F9E1. Drain pump was disconnected from harness. Reconnected and tested. Everything now working as designed.

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Oak Hills, CA 92344

Cesar

Job Details: 02/20/2024

Unit not filling properly cant see any water in the tub its agitating dry. reset electronics and ran a recalibration to teach computer empty cycle. Retested unit and now water fills to proper level all tested good

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Atwater, CA 95301

Doug S

Job Details: 02/20/2024

"Unit had bad latch, replaced and tested unit, working as designed"

We serviced a

KITCHENAID DISHWASHER

Model KDFE104HPS1

Near Winton, CA 95388

Doug S

Job Details: 02/20/2024

"Installed new adjusters and tested unit, working as designed"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Merced, CA 95348

Doug S

Job Details: 02/20/2024

"Found bad filter head, replaced and tested, working as designed"

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW3

Near Tulare, CA 93274

Enrique

Job Details: 02/20/2024

"Washing vibrating excessively (weak suspension). Replaced suspension assembly, performed calibration. Washing operating as designed. No leak."

We serviced a

MAYTAG DRYER

Model MGDC465HW0

Near San Fernando, CA 91340

ERICK H

Job Details: 02/20/2024

"Customer states long dry times. Started timed dry cycle on high temp. Upon initial cold start, flame only stayed on for 26 seconds. Internal air flow obstruction. Obstruction was in dryer filter chute. Removed obstruction and retested. Flame stayed on for 2 minutes and 37 seconds. Unit operating as designed. Job complete."

We serviced a

KITCHENAID DISHWASHER

Model KDFE204KBL2

Near Los Angeles, CA 91342

ERICK H

Job Details: 02/20/2024

Water in drip tray. Supply line was installed without a washer. Customer had washer on hand. Installed washer and reinstalled supply line. Unit operating as designed with no leaks. Job complete.

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Huron, CA 93234

Esteban S

Job Details: 02/20/2024

Suspension worn out. Suspension was removed and replaced. Unit is working as intended.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ08

Near Redlands, CA 92374

Francisco

Job Details: 02/20/2024

"Found torn gasket on right side rc door, removed and replaced gasket, unit now working properly."

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near San Dimas, CA 91773

Jaime

Job Details: 02/20/2024

found a damaged lid switch assembly. Had it replaced. Washer ok

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near New Cuyama, CA 93254

James

Job Details: 02/20/2024

Found drain hose too low causing siphoning. Raised hose and tested.Tested ok

We serviced a

MAYTAG DRYER

Model MGDB835DW4

Near Bakersfield, CA 93313

James

Job Details: 02/20/2024

Installed dryer repair kit due to bad idler pulley.Tested ok

We serviced a

KITCHEN AID REFRIGERATOR

Model KBBR306ESS01

Near Bakersfield, CA 93314

Jim

Job Details: 02/20/2024

Thermal mastic that covers the capillary tube was coming apart. Removed the mastic and cleared the drain. Unit tested ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHB00

Near Los Angeles, CA 91343

Joe P

Job Details: 02/20/2024

"Ice maker was leaking, replaced ice maker. Installed new ice maker, working as per manufacturer. Job complete."

We serviced a

KITCHENAID OVEN

Model KODE507ESS21

Near Los Angeles, CA 91356

Leon

Job Details: 02/20/2024

Replaced door glass Unit working properly as required

We serviced a

WHIRLPOOL DRYER

Model WED4815EW1

Near Modesto, CA 95351

Martin R

Job Details: 02/20/2024

Found vent hose was kinked and they covered the vent stopping air flow. Fixed vent hose and cleared out vent, tested unit dryer is heating and tumbling per design job complete

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEHZ00

Near Riverbank, CA 95367

Martin R

Job Details: 02/20/2024

Found filter is bad allowing air into system pulled filter water is dispensing properly job complete

We serviced a

WHIRLPOOL DRYER

Model WGD5605MW0

Near Baywood-Los Osos, CA 93402

Paul V

Job Details: 02/20/2024

Customer issue unit cut out. Diagnostics check. Disassembled unit. Found blockage lint in blower wheel/vent with faulty fuse. Removed existing fuse installed new fuse. Test brand unit. Unit operating at this time.

We serviced a

WHIRLPOOL DRYER

Model WGD6150PB0

Near Agoura Hills, CA 91301

Richard R

Job Details: 02/20/2024

"Upon arrival unit had a Maytag sticker on it on the front bulkhead. Replaced it with a whirlpool, nameplate job complete"

We serviced a

MAYTAG WASHER

Model MVWB835DC3

Near Riverside, CA 92501

Robert U.

Job Details: 02/20/2024

Found the unit had one error code stored at this time. F2e1 stuck button. I removed the error and preformed a user interface test. I ran the test several times and the error code didnt come back. I ran a suspension test and passed. I ran a diagnostic cycle and noticed a little bit of a shake coming from the unit. I adjusted the front left leg and that took care of that. I recalibrated the control and all functions are working properly. Job completed.

We serviced a

MAYTAG WASHER

Model MVWP576KW0

Near Riverside, CA 92503

Ruben O

Job Details: 02/20/2024

Replaced listed parts, cam bolt had fallen out

We serviced a

KITCHENAID RANGE

Model KFGC506JSS01

Near Los Angeles, CA 91326

Sean W

Job Details: 02/20/2024

Replaced defective gas manifold. Range now working properly.

We serviced a

MAYTAG WASHER

Model MVW6230HW1

Near El Monte, CA 91733

Andy

Job Details: 02/19/2024

"Unit shakes, replaced suspension rods and tested unit working properly"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FRSS2323AW7

Near Fresno, CA 93710

Doug S

Job Details: 02/19/2024

"Unit had a bad damper . Replaced and tested unit, working as designed"

We serviced a

MAYTAG WASHER

Model MVW5035MW1

Near Corcoran, CA 93212

Enrique

Job Details: 02/19/2024

"Washer not shifting f7e3 fault. Wrong actuator installed in factory. Replaced actuator, performed calibration. Washing operating as designed. No leak."

We serviced a

WHIRLPOOL WASHER

Model WTW8127LW1

Near Lemoore, CA 93245

Enrique

Job Details: 02/19/2024

Washer making noise during spin cycle. Missing rotor screw. Replaced slider assembly. Washer operating as designed. No leak.

We serviced a

MAYTAG DRYER

Model MGDB835DW4

Near Castaic, CA 91384

Felipe S

Job Details: 02/19/2024

"Upon arrival found unit with error code F4E3 and F2E1, this about restricting air flow and stuck key. Erase the error code on the unit, test the unit and unit doesnt have any internal block. This unit is working properly the problem is with the ventilation system from the house. Job complete"

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS0

Near Nipomo, CA 93444

George

Job Details: 02/19/2024

"Found dishwasher not draining clear air gap and retested. unit functioning as design."

We serviced a

WHIRLPOOL OVEN

Model WFG320M0BS3

Near Camarillo, CA 93010

Isidro

Job Details: 02/19/2024

"Installed and secured ordered parts, unit is now lighting and operating as designed, customer approved repairs and service"

We serviced a

WHIRLPOOL WASHER

Model WTW5105HW0

Near Ventura, CA 93003

Isidro

Job Details: 02/19/2024

"Squeaking noise coming from cracked belt and pulley, Installed and secured parts listed,calibrated unit and is now operating properly as designed customer approved repairs and service"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF302ESS02

Near Upland, CA 91784

Jaime

Job Details: 02/19/2024

Replaced the damper control. Fridge ok

We serviced a

MAYTAG WASHER

Model MVWC565FW3

Near San Dimas, CA 91773

Jaime

Job Details: 02/19/2024

Repaired drain pump harness wires. Washing machine works OK

We serviced a

GENERAL ELECTRIC DRYER

Model PTD90GBPT0RS

Near Bakersfield, CA 93313

James

Job Details: 02/19/2024

Removed drum and lubricated idler pulleys.Tested ok

We serviced a

AMANA WASHER

Model NTW4519JW2

Near Lancaster, CA 93535

Jonathan

Job Details: 02/19/2024

"Found defective suspension rod fixed, suspension rod, tested unit and working properly"

We serviced a

WHIRLPOOL OVEN

Model WFG535S0LS5

Near Burbank, CA 91501

Leon

Job Details: 02/19/2024

Cx states that unit is not working in oven bake Replaced all selected parts Unit working properly as required

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS11

Near Burbank, CA 91501

Leon

Job Details: 02/19/2024

Cx states that door gasket is out of position Remove and reinstalled door gasket properly Tested unit working properly as required

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near Modesto, CA 95355

Martin R

Job Details: 02/19/2024

Found bad control. replaced control and tested unit. washer is filling agitating, draining, and spinning per design job complete

We serviced a

WHIRLPOOL DRYER

Model WGD5010LW3

Near Los Angeles, CA 91343

Paul M

Job Details: 02/19/2024

"Unit had moisture around, vent did not have proper ventilation and console was malfunction. Replaced part, adjusted ventilation and unit is now working properly. Job complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ10

Near Modesto, CA 95355

Rich

Job Details: 02/19/2024

Reseated loose door gasket. Operating as designed.

We serviced a

WHIRLPOOL DRYER ELECTRIC

Model WED4815EW1

Near Thousand Oaks, CA 91360

Richard R

Job Details: 02/19/2024

"Upon arrival inspected unit and found idler belt was snapped. Also had worn pulley wheels and idler wheel. Replaced it with the idler pulley kit. Put unit back together tested unit is now working as intended. Job complete."

We serviced a

GENERAL ELECTRIC DRYER ELECTRIC

Model GTD72GBSN0WS

Near Riverside, CA 92506

Robert U.

Job Details: 02/19/2024

Found motor retaining clip cam off and reason for the noise. I reinstalled clip and now the unit is rotating and no longer making noise. All functions are now working properly. Job completed.

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW2

Near Riverside, CA 92507

Robert U.

Job Details: 02/19/2024

Found drum not rotating due to broken belt. I replaced the belt and pulley from dryer repair kit and now the unit is rotating and heating properly. Job completed.

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near San Bernardino, CA 92410

Rod

Job Details: 02/19/2024

Makes noise when agitating confirmed. cam assembly was not aligned with drive pulley completely. Adjusted for complete coupling of cam and pulley. Designed operation was restored.

We serviced a

WHIRLPOOL DRYER

Model WGD5050LW3

Near San Bernardino, CA 92410

Rod

Job Details: 02/19/2024

Door issues to tight confirmed. Adjusted door catch and hinges. Designed operation returned

We serviced a

MAYTAG DRYER

Model MEDB765FC0

Near Manteca, CA 95337

William

Job Details: 02/19/2024

"Replaced drum/idler wheels & belt, with dryer repair kit, cleared debris found in blower wheel housing, ran dryer cycle, unit sounds & operating as designed."

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN9WW

Near Apple Valley, CA 92308

Brian G

Job Details: 02/17/2024

Removed and replaced suspension. Tested operation. All OK.

We serviced a

MAYTAG WASHER

Model MVW6230HW2

Near Fresno, CA 93711

Doug S

Job Details: 02/17/2024

"Installed new run capacitor and tested, working as designed"

We serviced a

MAYTAG WASHER

Model MVW7230HC1

Near Fresno, CA 93720

Doug S

Job Details: 02/17/2024

"Found cam pulley loose, tightened up and tested unit,working as designed"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model GRMS2773AF01

Near Fresno, CA 93722

Doug S

Job Details: 02/17/2024

"Installed new ice maker and tested, working as designed"

We serviced a

WHIRLPOOL WASHER

Model WTW6157PW0

Near Friant, CA 93626

Doug S

Job Details: 02/17/2024

"Installed new strike and tested unit, working as designed"

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN3WW

Near Victorville, CA 92392

Drew M.

Job Details: 02/17/2024

Ran diagnostics and found 11 27 10 29 26 error codes. Ran fill test. Filled in just over 2 minutes. Spin cycle had a squealing. Replaced the belt and ran cycle. Unit passed all tests and is now operating as designed.

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model PVD28BYNDFS

Near Victorville, CA 92392

Drew M.

Job Details: 02/17/2024

Found the gasket hanging down and stoped the door from closing properly. Reattached the gasket and closed everything properly. Ran cycle and unit passed all tests. Unit is now operating as designed