"Replaced defective vent, tested unit and is working properly"

"Removed and replaced parts listed, tested ops unit working ok,no damage by tech."

Removed and replaced user interface at deli drawer and user interface harness removed and replaced dispenser paddle and switch due to sticking during dispensing. All OK

Wire harness was removed and replaced. Unit passed all test. Unit is working intended.

Fixed- installed new part (lower harness) calibration test pass- auto test pass- no leaks- no errors- cx ok repair

No response from console uiConfirmedreplaced defective ui control with no leaks designed operation was restored

"Installed gearcase, belt, actuator, drive pulley, drive hub kit and washplate. Performed calibration, initiated quick wash cycle. Washer operating as designed. No leak."

"Installed power cord, and main harness. Range now operating as designed."

Installed blower assembly. Range operating as designed. No gas leak.

"Not responding, replaced controls tested unit working properly"

"Fixed- found door to be hard to open/close, found catch to be broken- removed bad one and then installed new one (catch) door is now opening/closing easily- cx ok repair"

"Install the new interlock switches on the unit. Retest the uni, and now is working properly. Job complete."

Install the new control board and pump on the unit. Retest the unit and now unit is working properly. Job complete

Ran diagnostics when arrived. Would not exit drain step. Replaced acu and tested. Unit now working as intended.

Units lid strike was broken upon arrival. I replaced it with a truck stock part. Unit is now operating normally.; used 1 W11457841 (Strike) from stock

Units capacitor fell off of the transmission again. I used a larger screw to re-secure it. Replugged harnesses and unit is now running normally again.

Wash motor was not running upon arrival. Replaced it with preID part. Unit is now operating as designed.

"Installed new IM and gaskets, all functions now working as designed."

"After a new harness jumper was replaced, consumer was asked and informed about how and when to repack the groceries back."

"Installed new Gearcase, pulley, motor, shifter and retested unit now working as designed job completed"

Replaced elements and tested unit unit working as designed

Installed diffuser exexively loud retested unit functioning as design.

"Found unit had bad power cord. Removed and replaced. Tested l, unit now has power."

Installed parts tested on a fill wash and drain and spin tested ok complete.

Compressor failure. Removed and replaced compressor and dryer. Charged unit with 56 g of R600. Allow 24 hours to stabilize

"Installed belt clutch, shifter pulleys. Tested, unit functions as designed."

"Installed harness and latch, performed calibration. Washer operating as designed. No leak."

After replacing the door for the cosmetic issue I heat treated the door gaskets for better sealing. I recommend leaving the door closed for a hour or two to allow the door to conform to the new doorway. All functions tested ok and door was okayed by the customer. Job completed.

Replaced belt tested unit unit working properly

"Fixed- found shield to be deformed causing shield not to snap into frame, removed bad one and then installed new one (2 shields) shield snapped into frame, all test pass in diagnostic- cx ok repair"

"Installed new compressor, dye drier, service valve, heat exchanger tube and evaporator, pulled vacuum for 10 minutes unit held. Then charged with 5.5 onces of R134, unit started pulling heat and cooling as designed at this time of service"

Found the unit had a f2e1 error code stored shorted or stuck keypad. I removed and replaced the main control that has the user interface inter graded into it and ran a bale cycle. All tested ok after replacing defective touchpad control. Job completed.

"Motor is dead,replaced motor and sump assembly and successfully ran diagonal cycle without inturuptions or any error codes displayed,dishwasher now working properly."

Found the right side door gasket torn and not sealing. I replaced the refrigerator door gasket and heat treated for better sealing. I found the issue with the water dispenser and ice maker is the filter clogged. When I put my by pass plug the water dispenser and ice maker work. Recommend getting a genuine whirlpool filter. All functions of the door checked ok after repair. Job completed. Recommend leaving right door closed for the next hour or two.

"Thermistor wire partially torn,replaced thermistor,fridge now cooling properly.; used 1 W11724692 (Thermistor) from stock"

"On arrival, Cx stated right door gasket is ripping, opened diagnostics program to check damper , test # 3, it passed 01- damper opens, 02- damper closes, No need to replace damper at this time.Cx advised to lower FC temperature from 37* to 39*,2 degrees Fahrenheit and monitor cooling in crisper drawer and cold spots, will check with tech line tomorrow on issue and get back to Cx.Additional parts included in attention notes."

Unit door wont latch. Broken latch key on door. Needs a new door WB56X20639$208..

Found high limit cut off bad replaced high limit cutoff tested unit unit working as designed

Found timer not turning replaced timer tested unit time running ok complete.

"After hinge and new lid were replaced, proper functional testing of lid was successfully achieved."

Cycled unit and found belt slipped off causing damage to cam. Installed new cam and new belt retested unit now working as designed job completed

Found bolt from drive pulley loose and caused drive pulley to crack replaced drive pulley unit working as designed

"Removed and replaced units ACU and latch. Tested, unit now going into cycles. Job complete."

Replaced led lights and checked out. Now unit is lighting as designed and checked out all other functions on unit. All checked out and passed. Job completed

Removed and replaced drain pump. Tested. Now working as designed.

Replaced compressor and evaporator. Recharged with 56 grams of r600. No leaks found u it regulating to temps.

"Installed and secured new rights side over blower cooling fan, mice issue bit the grommet on fan. I Tested the unit on bake to 350 degrees. Unit is now operating as designed at this time of service"

Oven control lost communication after power outage. Error codes were deleted. Unit passed all test. Unit is working as intended.

Cx complaint. Not finished cycle. Upon arrival. Mirand diagnostics. Found error codes for Long fill error code. 8-1. And Long drain cycle. Installed pumps for drain and valves for long filling. Tested components out okay. Operating as designed

Found line in back rubbing on fan. Adjusted out of the way. Also added screw to door hinge that was missing.

Replaced the sump and motor. Tested unit for function and leaks after. Everything is working as designed at this time .

"Installed latch, ran diagnostic cycle test all passed. Job complete."

Found lint blockage in blower wheel housing preventing airflow. Cleared and tested. Unit is heating normally.

Element is open. Replaced element and tested. Returning unused parts.

Checked for faults and found 7-4(basket reengagement fault) found the unit has a damaged slider and rotor because of missing fastener. Called Square trade and told them the parts needed to repair thisW10734521 sliderW11260238 rotorW10752189 fastener

Clogged center burner. Burner was cleaned and cleared from food debris. All burners are working. Unit is working as intended.

"Suspension were weak, replaced with new suspension rods. Calibrated unit and is now working properly."

"Codes F7E3, F6E3, F3E3.. cleared codes.Slider has fallen down. Ran diagnostic cycle all passed. Informed customer that stand pipe is plugged, informed customer he will to call a plumber."

Cx states washer shakes aggressively during spin cycle. Suspension has failed. Cx declined repairs. Job complete.

"Unit making loud noise during operation. Tested unit and found idler pulley making a loud noise and rollers are worn. Removed and replaced rollers, idler pulley and belt. Tested unit. All tests good."

"Replaced hose connectors at bottom of door, Tested water valve operations, instructed cx on normal water valve functions. Unit operating as designed"

"Needs 2x labor for the uninstall and then reinstalled of a stacked unit .I was getting a F2E1 error code. I uninstalled unit replaced the consul, then reinstalled unit properly. Tested unit after for function. Everything is working as designed at this time"

"Checked the unit upper rack was off the track , could have caused the unit to leak , repaired the upper rack and track assembly so it works correctly tested operations unit unit is working as designed now no leaks found at this time."

"Unit was slipping wheelie in a med spin. Replaced parts cam, actuator and belt. Tested again and unit can spin out no problem. Tested and calibrated unit. Job completed ; used 1 W11239857 (Belt), and 1 W10721967 (Cam) from stock"

"Water supply checked good from wall, I found a bad water valve. I installed new water valve unit is now dispensing water as designed, cx approved repair and service water valve, no leaks visible anywhere"

unit not draining and making scrape when basket is turning. I found that the slider is scrapping on clutch and drain pump has voltage but not draining. Unit will need slider and pump assy. Customer declined repair

Cx states dishwasher not turning on. Found loose connection from power cord inside junction box. Tightened up all connections. Tested unit. Unit operating as designed. Job complete.

"F2E1; F0E3, found control board throwing overload error while the load is very small, inspected the slider and in between the basket and tub for friction, nothing. Unit need control board and shocks, cx declined estimate for repair, getting new unit. Complete"

Upon arrival inspection of unit found cycle selector knob seized and not working replaced control panel with new knob tested unit is now working as intended job completed

"Checked the unit , washer doesnt recognize lid shut , checked the strike , busted , replaced the strike tested ops ok now at this time"

"Broken strike, installed new latch assembly and strike, unit is now working as designed, cx approved repair and ser"

"JB OUT 11/20/24Customer states washing machine makes loud banging sounds spin cycle. Upon arrival, tested washer and spin cycle verified door hinge loose. Tightened all mounting screws for door hinge and retested operation. Unit now, spins smoothly and quietly. Advise customer front load washers prefer, and are designed to hold larger loads and will spin more smoothly with larger loads as opposed to small wash loads. Additionally advised customer against use of HE turbo detergent and any detergent pods as they are too highly concentrated For this low, high-efficiency washing machine. No parts needed no charge to repair job complete."

"Washer was not operating. Drain pump broken wire harness (black/white wire). Installed lower harness, performed calibration. Washer operating as designed. No leak. ; used 1 W11643701 ( Harms-wire) from stock"

"JB out 11/20/24.Customer states water in dishwasher is not hot.Upon arrival dishwasher was running a wash load.Opened dishwasher and verified water was slightly warm.Canceled current Wash cycle. Tested in NORMAL wash cycle and verified water being supplied to the dishwasher is far below the required 120f minimum as outlined in the factory supplied Installation guide (page #8). Water entering the wash tub is approximately 65-75f. House water heater is too far from dishwasher and HOT water pipe in concrete slab (November-February) is very cold and cools the water quickly resulting in cool water being supplied to dishwasher.Ran Diagnostics and extracted only one stored error code F7E1 indicating water is too cold. Cleared stored error code. Ran Service diagnostics and verified with customer present that the heating element does heat as designed but cannot heat the incoming water (74f) to the minimum of 120f. During heating element test, the heater melted ice cube quickly.Recommend the installation and use of a Point of Use Hot water heater mounted under the kitchen sink, supplying Hot water to only the Dishwasher itself set to a minimum of 125f. Reset onboard Computer Control..Also advise this model dishwasher has a stainless steel inner door panel but a Plastic wash tub. The plastic wash tub does NOT hold the heat and therefore will not dry ceramic, metal and glass items unless water temperature is no less than 120f and will not provide good drying results on Plastic items being washed as they do not hold the heat well.No charge to customer. JOB COMPLETE"

"Tested unit found defective valve, replaced defective valve tested unit and is working properly, customer educated on use and care of unit; used 1 W11641117 (Valve) from stock"

"Found cx using non he soap causing lot of foaming and leaks by the door side. Installation was tilted forward too that cause water to be in the switch tray, reinstalled unit and adjusted the legs and calibrate unit. Cx need to Change detergent though. Complete"

"Not going in to spin and makes noise, found actuator,belt,pulley bad, replaced actuator,pulley and belt tested unit working properly"

Cx states washer not powering on. Confirmed issue. Control failed. Replaced control. Tested and calibrated unit. Unit operating as designed. Job complete.

"Checked the unit temperature in the freezer 0°F , tested ice maker jammed , cleared the ice , tested harvest , passed ok unit filled up with water ok , reset the controls checked the air flow across ice bin operating ok now at this time , allow 48 hrs to start making ice and 3 days to fill ice bin"

Cx states dryer not heating up after repairs done last week. Igniter wasnt glowing. Disassembled dryer. Igniter was unplugged. Reconnected igniter. Tested unit. Unit operating as designed. Job complete.

Cycled unit and found shorted control and capacitor installed new control and new capacitor retested unit working as designed job completed

Bad faulty capacitor unit is going straight to done when cycle is started. I installed new capacitor and unit is now agitating and spinning as designed

"Noise heard during spin, noise coming from Gearcase shaft causing worn splutch and belt. Cx declined at this time, will contact manufacture for assistance."

"Found pulley slipped loose knocking belt ajar. Secured pulley with new nut with loctide and realigned belt. Tested, unit now performing as designed."

"Customer states unit was leaking water, ran diagnostics test found no leaks visible anywhere I opened the back panel , found water in drip Pan from leak look like dry suds on closer inspection found to what it looks like suds or foaming coming from back venting tube, too much soap or detergent being used"

"Found units hot water valve backed out. Secured and tested, unit no longer throwing lo flo code."

"Upon arrival found unit with detergent on the bottom of the unit, no getting dissolved. Check the unit and found error code F7E1, this about single speed wash motor failure. Erase the codes and run the unit on diagnostic cycle, after diagnostic unit still have the same error code. Replace the pump assembly on the unit. Retest the uni, and now is working properly. Job complete"

Unit is leaking on the left side of unit from possibly the valve area. Checked out valve and took top off. Found hoses not tighten and followed the water through out unit. Came from valves were hose came from. Tested and unit is working as designed. Found f2e1 and no other codes. Job completed

Installed a new latch assembly washing machine OK

"Broken belt, Installed new dryer repair kit, unit is now operating as designed."

"I adjusted the igniter closer to the pallet because its was far of causing gas buildup, oven works and reaches temperature between the recommended time frame, cx complain about the right front burner flame that its too high, unit flame its ok picture attached, lowest flame or warm flame cant be achieve on that particular burner, because its the biggest BTU, cx has options of other smaller burner with smaller BTU for that purpose. Unit test ok. Complete"

"Unit need a main cntrl, pump is continuously running- f7e1 long drain"

Unit stayed I sensing and never going into wash cycle. Replaced capacitor and tested through diagnostics and unit functions as normal.; used 1 W11395618 (Capacitor) from stock

Found defrost issue in freezer causing diffuser to stay open causing fridge compartment to freeze. Will need new diffuser.; ordrng 1 W10861170 (Diffuser)

"After running multiple diagnostics, unit still going into f3e3 error code. Will replace ACU again along with upper wire harness.; ordrng 1 W11550453 (ACU) and 1 W11744014 (Upper harness)"

"Units drain pump rattling and not pumping any water. Will need new drain pump. Also unit was installed incorrectly with missing electrical cover panel and unit insulation never installed, just left next to machine. ; ordrng 1 W11462456 (Drain pump)"

"Needs 2 call count Freezer upper slide shelf doesnt pull out , busted slides and shelf front and pan upper and middle , ordered parts to repair the unit properly ; rqstng P&A on 1 W11387053 (Bin upper) and 1 W11131390 (bracket LFT) and 1 W11161915 (bracket RIGHT) and 1 W11387048 (Bin freezer middle asm)"

Found broken latch. Ordering part and rs for Friday ; ordrng 1 WH08X32657 (Latch)

"Throughout a functional testing on the, I observed a heavy tapping, and rough shifting, and during the spin cycle, a loud metallic squealing was heard as well. My recommendations are, gear case, clutch, slider, spammer, and screw.Attn, Vonnie, it needs authorization.; ordrng 1 W10909670 (Spanner) and 1 W11393685 (Gearcase) and 1 W10734521 (Slider) and 1 W10754448 (Clutch) and 1 W10752187 (Screw agitator)"

"Visual and physical inspection plus a functional testing were conducted and found a unit that is working as designed but it has a lazy drain, a drain pump is recommended to be replaced.; ordrng 1 W11458345 (Drain pump)"