Local Reviews
Powered by Fluid LOCAL
Jim S.
REFRIGERATOR WHIRLPOOL WRX988SIBM01 "The unit completely shut down. Will need to order the user interface and relay board; ordrng 1 W10789393 (cntrl-elec), 202.08, 1 W10807590 (cntrl-elec), 154.22"
James G.
M/W OTR WHIRLPOOL WMHA9019HZ1 "Unit has been working since Thanksgiving. Rick at tech line says it could be interference from other things on same circuit. Unit had F-6/E-0 which is on tech sheet tech line says communication issue however unit is working during visit, cleared codes"
James G.
M/W OTR WHIRLPOOL WMH53521HZ3 Replaced door due to inner abnormalities Tested ok
James G.
DISHWASHER WHIRLPOOL WDT970SAHZ0 Replaced listed parts due to no operation Tested ok
Isidore A.
DRYER WHIRLPOOL WGD9400SW1 "Removed top, front and bottom panels, removed drum, belt and all the rollers including pulley and motor pulley. Install new motor pulley and all new parts from dryer repair kit, reinstalled panels. test dryer operation ok at this time. Note customer advised that venting is not correct has two dryers going into same vent."
Isidore A.
DISHWASHER KITCHENAID KDTM504EPA2 "Removed front panel disconnect all wiring from dishwasher and installed new wiring harness including led wire harness, test dishwasher operation ok at this time reinstalled front panel."
Jesus C.
WASHER MAYTAG MHWE550WW01 "Customer states that unit has error code. Checked unit and ran diagnostics found several error codes. Hose was place to far in the drain causing siphoning. Ran test and found the bearing on tub bad. Still need drain pump or pump not working right. Ordering parts.F-20 no water detected entering unitF-21 long drain; ordrng 1 W10250762 (tub-outer,fnt), 89.16,"
Isidore A.
OVEN KITCHEN AID KEBS277SSS02 "Removed oven from wall cabinet found lower oven thermal cutoff open installed new thermal cutoff and as preventative maintenance removed old blower and installed new cooling blower, test and checked oven calibration oven at 350 degrees F. Found oven at approximately 365 degrees F. Calibration on control is set at 30 degrees F. For both lower and upper ovens customer aware oven I’ds over 10 degrees F. Temperature"
Jesus C.
REFRIGERATOR WHIRLPOOL KRMF706ESS01 Unit is still doing same thing with new tube. Ordered a from manufactureJkSr7723481467
Isidore A.
DRYER MAYTAG MED5100DW0 "Found F4E3 venting error not verified dryer is working . Properly, no check vent errors on control, customer advised to have vent professional checked, but should try timed dry cycle for lighter loads which may have cause dryer to stop. Since there was not enough clothes to sense wet clothes."
Irvin F.
OVEN FRIGIDAIRE FFEF3003NW0 "CX says the units front left burner failed. The switch is not sending correct power. Replaced element and switch. Test, passed all ops normal."
James M.
REFRIGERATOR KITCHENAID KRFC704FPS00 Found broken wires to fill tube. Ordering new water tube assembly; ordrng 1 W11230096 (WATER TUBE ASSEMBLY)
Irvin F.
REFIRGERATOR FRIGIDAIRE LFSS2312TFP0 Replaced failed bulb. Works good. Done.
Irvin F.
WASHER WHIRLPOOL WTW5000DW1 "S225EQInstalled main control. Test components. Calibrated unit, all ops normal."
James M.
DRYER SPEEDQUEEN ADG3SRGS115TW01 Fund unit making rumbling during operation due to bad roller wheel.
Irvin F.
WASHER WHIRLPOOL WTW4816FW2 "The washer is not filling with cold water. Found the solinoid is not opening fully. Removed hose from valve, the water supply is good. Hot and cold. Installed replacement valve. Ran test passed. All ops normal."
James M.
OVEN WHIRLPOOL WOS51EC0AS Found unit with broiler fault. Also found unit to run hotter than expected dusting bake cycle due to bad probe; ordrng 1 WPW10260252 (elmnt-brol)
Irvin F.
WASHER MAYTAG MVWX500XW0 "CX says the unit is not operational. Error codes found failed main control, and bad shifter. Replaced control and shifter. Ran calibration, passed."
Irvin F.
WASHER WHIRLPOOL WTW8000BW0 "Removed power. Installed suspension. Ran calibration cycle, passed. All ops normal."
James G.
WASHER WHIRLPOOL WTW8500DC0 No show;
Irvin F.
REFRIGERATOR WHIRLPOOL WRT518SZFM00 The units upper hinge was loose. The door was floating. Tightened screws. All ops normal.
Hector Z.
MICROWAVE KITCHENAID GBD277PDS3 Duplicate call.
Hector Z.
DISHWASHER KITCHENAID KDFE304DSS0 Replaced control panel. Tested ok.
Hector Z.
WASHER MAYTAG MHW5500FW0 "The washer door is locked and the drain pump is constantly running. Set unit in diagnostic and found no error code. Also ran a quick diagnostic test to be able to open the door. Contacted the tech line and she suggested that the drain hose was too far in into the drain, also found the hot and cold water hoses were reverse. Adjusted drain hose and suggested to the customer to replace both faucet because there frozen up. SR 7723605229. Tested ok."
James G.
COOKTOP JENN-AIR CVEX4370B ordrng 1 AR141B (series 7 radiant bla)
Hector Z.
REFIRGERATOR WHIRLPOOL WRT549SZDM01 Replaced ice maker. Tested ok.
Hector Z.
DRYER WHIRLPOOL WGD92HEFC0 Replaced coils and temperature sensor (Wire harness). Tested ok. I informed to the customer that the damaged side panel (Rh) and the drum was denied by the insurance company.
Hector Z.
WASHER WHIRLPOOL WFW92HEFC0 "Replaced door bellow. Ran a quick diagnostic test, tested for leaks. Tested ok."
George Y.
WASHER WHIRLPOOL WFW94HEXR2 Installed part tested ok complete . No dents or dings cause by tech.
George Y.
DISHWASHER KITCHENAID KDTM404ESS0 Found dishwasher not washing sump motor just humming need to replace sump motor assembaly replaced part tested check out ok complete no dents or dings cause by tech.
George Y.
REFRIGERATOR WHIRLPOOL WRF535SWHZ01 Found refrigerator top of freezer center small settlement of ice remove reposition gasket retested check out ok complete no dents or dings cause by tech.
Irvin F.
WASHER MAYTAG MVWC565FW1 "No errors. All ops functions. The suspension is weak, causing poorish performance in spin. Replacing suspension. ; ordrng 1 W11130362 (SUSPENSION)"
Irvin F.
WASHER MAYTAG MVWC415EW2 "CX says unit is not completing cycles. Found error code for hi rinse water temp, and load off balance. Suspension test failed, suspension is bottoming out. Need suspension. ; ordrng 1 W10780044 (suspension)"
Erick S.
WASHER GE GTW330ASKWW Cycled unit through diagnostics and found unit with door latch error causing it not to advance in wash. Replaced door latch and reprogrammed main board. Retested it and it passed all tests with no errors. Job complete ; used 1 WH01X27954 (LID LOCK) from stock
Erick S.
WASHER MAYTAG MVWC555DW Cycled unit through diagnostics and found suds error causing it not to advance in wash. Reprogrammed main main and ran tests cycle and it passed all tests with no errors. Informed cust of soap usage. Job comp
Erick S.
WASHER WHIRLPOOL WTW8500DW "Cycle unit and found it f9e1 erro indicating pump failure. Found pump seizing causing it not to drain and have error. Replaced pump. Retested it and it passed all tests with no errors, job comp; used 1 W10876600 (PUMP-WATER) from stock"
Erick S.
RANGE GE JGBS66REKSS "Inspected unit and found unit burner tube only lighting a quarter of the way. Flame spreader causing carbon error. Removed and cleared spreader. Burner is now working as design with no errors, Aldo found display flickering. Found bad pin connector causing error. Repaired connector and secured it to main hoard. Board is now working with no errors. Job comp"
Erick S.
ICEMAKER WHIRLPOOL WRF767SDHZ "Installed new adapter on unit, retested and unit is cooling with no errors. Job complete"
Erick S.
WASHER MAYTAG MVWC416FW Cycled unit and found it with fill error causing it not to advance in wash. Found bad cold solenoid not opening all the way. Replaced valve . Retested it and it fills now with no errors. Job complete
Erick S.
REFRIGERATOR KITCHENAID KRFF707ESS01 Installed new parts on unit. Retested it and it passed all tests. Unit is now cooling. Job complete
Erick S.
REFRIGERATOR FRIGIDAIRE LGHX2636TF "Inspected door and found it leaning to the right and not closing correctly. Removed door and found cracked door cam causing error. Replaced door cam, , Retested it and door is now aligned correctly and closing with no air gaps, Job complete ; used 1 241990301 (DOOR CAM) from stock"
Hector Z.
OVEN KITCHENAID KODC304ESS00 Upper oven 20deg off calibration. Adjusted upper oven temperature. Lower oven has a open thermal fuse due to self cleaning.; ordrng 1 W11165152 (OVEN THERMOSTAT.)
Erick S.
WASHER GE GTW330ASKWW "Cycled unit and found it with drain pump error causing it not to drain. Tested pump and found it bad, replaced pump, unit is now draining and cycling with no errors. Job comp; used 1 WH23X27574 (DRAIN PUMP, ) from stock"
Erick S.
REFRIGERATOR WHIRLPOOL WRF757SDEH01 Installed new parts on unit. Retested it and it’s now cooling with no errors. Job comp
Erick S.
RANGE FRIGIDAIRE LFGF3054TD "Found installed new parts on unit. Retested it and display is now working, oven cycled and heated with no errors. Job comp"
Dane K.
WASHER MAYTAG MVWB835DW0 Upon arrival of the unit would not spin and was screeching when filling and would not get the close all the way wet. It would not spend because the door would not latch and found water valve faulty. Removed and replaced door latch and water valve and calibrated and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR FRIGIDAIRE FGHF2366PF/FA Installed control and tested unit. Unit functions. Normal now
Dane K.
MICROWAVE OVEN JENN-AIR JMC2430DP01 "Removed and replaced magnetron, magnetron thermostat, and control board and tested unit. Unit functions normal now"
Dane K.
WASHER FRIGIDAIRE FFTW4120SW Installed control and lid lock and tested unit. Unit functions normal now
Dane K.
WASHER WHIRLPOOL WTW4855HW1 Installed control and calibrated and tested unit. Unit functions normal now
Erick S.
REFRIGERATOR WHIRLPOOL WRF736SDAM14 Cycled through diagnostics and found fan motor not running. Accesed motor and found very low frost pattern causing it not freeze. Motor getting voltage but not responding. amp draw indicating low charge or leak. Recommended to replace motor and recharge system for proper cooling ; ordrng 1 W10865431 (motor-evap) and 1 WPW10143759 (dryer)
Bryan D.
WASHER WHIRLPOOL MVWB835DC3 Removed and replaced the housing and drawer. Unit is functioning as designed. No dents dings or scratches caused by tech.
Bryan D.
DISHWASHER WHIRLPOOL KUDE20FBSS1 Removed and replaced control. Ran unit. Unit is now functioning as designed. Dents dings or scratches caused by tech.
Bryan D.
WASHER WHIRLPOOL MVWC200BW0 Cx states washer just continues to go into cycles by itself after the original cycle completes. RN diagnostics got no error codes ran a test cycle unit performed as designed.
Bryan D.
REFRIGERATOR KITCHENAID KUDF204EPA00 Cx states firsts is not cooling. Upon arrival unit was turned off. Told cx if unit doesn’t cool to give us a call after turning cooling on. Cx also asked for me to install knob back onto filter upon doing so found the filter housing was loose and all grades were not screwed in. Informed cx. Cx stated they. Pull not have a second visit and will be contacting pacific sales to demand unit gets replaced.
Bryan D.
DISHWASHER WHIRLPOOL WDF320PADS1 Removed and replaced UI panel. Unit is now functioning as designed. No dents dings or scratches caused by tech
Dane K.
DRYER WHIRLPOOL MDG5500AWQ Unit was not drying the clothes a timely fashion because it had a massive plant buildup in accordion style tubing behind dryer and also in customers home. Short and vent for customer and ordering ripped lint screen; ordrng 1 WP33001808 (screen)
Bryan D.
MICROWAVE WHIRLPOOL WOC75EC7HS00 Cx states panel went blank and hasn’t came back on. Removed and replaced control panel. Unit is now functioning as designed. No dents dings or scratches caused by tech.
Bryan D.
DISHWASHER WHIRLPOOL WDF320PADS1 Removed and replaced UI panel. Unit is now functioning as designed. No dents dings or scratches caused by tech
Aaron B.
OVEN WHIRLPOOL WFG320M0BW2 "Replaced the oven igniter tested unit , ops normal at this time"
Dane K.
REFRIGERATOR GENERAL ELECTRIC GSS25GSHJCSS Unit needs new cover ; ordrng 1 WR49X10251 (cover assembly ff inlet)
Billy J.
REFRIGERATOR WHIRLPOOL JS48PPDUDE Cx stated bestbuy came and fixed unit job complete
Dane K.
WASHER GE GTW330ASK Upon arrival the unit would not wash. Found control not responding. Unit needs new control ; ordrng 1 WH18X28176 (CONTROL )
Billy J.
DRYER WHIRLPOOL MGD6000AG1 upon arrival removed and replaced water valve retested job complete
Aaron B.
DRYER MAYTAG MGDC215EW2 "Unit timer wasn’t advancing, replaced the timer tested operating normal now"
Aaron B.
M/W OTR MAYTAG MMV4206FZ5 "Replaced the mag and diode , tested ops normal now unit heats good now"
Aaron B.
REFRIGERATOR WHIRLPOOL WRS571CIHW00 the oven door was off of the range Both the left and right hinges replaced them both reinstalled the door operating normal now
Bryan D.
REFRIGERATOR KITCHENAID KSC24C8EYY02 Cx states after last visit the fridge stopped cooling. Inspected unit and found compressor not running. Removed Nd secured connection at start device and compressor started. Then stopped running again. Grabbed a start device from truck and compressor still not starting. Ordering compressor motor was not pulled. ; ordrng 1 W10309988 (compressor)
Bryan D.
REFRIGERATOR WHIRLPOOL WRF560SEYM00 C states water is leaking from ice maker. Found ice maker is leaking. Ordering ice maker; ordrng 1 4211173 (sub 4317943)
Aaron B.
REFRIGERATOR WHIRLPOOL WRX735SDHZ01 "Unit compressor has a louder than normal ring buzzing noises , to correct issue needs a new compressor ordered part; ordrng 1 W11209866 (COMPRESSOR ) and 1 WPW10143759 (dryer)"
Aaron B.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 "No lights in the refrigerator or freezer sections , ordered per service flash , ordered parts; ordrng 1 W10830288 (cntrl-elec)"
William L.
REFRIGERATOR WHIRLPOOL WRX735SDHV00 "found ice jambed & broken water filter cover, Replaced ice maker, ordered broken water filter housing cover & water valve.; ordrng 1 W11043013 (valve) and 1 WP67006331 (cover-filt), used 1 WPW10300024 (ICEMAKER) from stock"
William L.
WASHER WHIRLPOOL WTW8600YW0 "found water flow overflowing fabric soften dispenser, ordered water valve & dispenser parts, adjusted valves on wall didn’t help, ; ordrng 1 W10853723 (valve) and 1 WPW10136371 (bezel) and 1 WPW10172146 (dispenser)"
William L.
WASHER MAYTAG MVWC565FW1 "leveled legs on floor, ran self diagnostics, tested ok, instructed cx on loaded clothes & balancing loads."
William L.
WASHER WHIRLPOOL MVWB850YW0 "Found main bearing completely failed, replaced bearing with bearing rebuild kit, ran spin test, ran self diagnostics, unit operating as designed."
William L.
REFRIGERATOR WHIRLPOOL WRS315SDHZ00 "checked temps, temp in freezer 0 degrees, ice maker production very slow, bumped ice maker, ordered ice maker and control for unit.; ordrng 1 W11203924 (main control) and 1 WPW10300022 (icemaker)"
Tyler F.
WASHER WHIRLPOOL WTW5000DW1 Customer stated that the drain cycle is not working. Checked for error codes found long drain error code. Cycle tested unit found unit is draining and all is working good. Calibrated unit all works good at this time.
Tyler F.
REFRIGERATOR WHIRLPOOL KSSC48QTS02 Customer is having similar issue. This time the frost was under the ice bin. Found the door flap for ice dispenser is not sealing. Removed and replaced door and ice door motor tested all works good at this time.
Tyler F.
MICROWAVE IKEA IBMS1455DS00 Customer stated that the cancel button is not working. Removed and replaced it tons in interface kit. Tested all works good at this time.
Tyler F.
OVEN KITCHENAID KODE507ESS02 Customer stated that the fan is noisy in the top oven. Removed and replaced fan blade test3d all works good at this time.
Tyler F.
ICEMAKER KITCHENAID KUID508ESS0 Customer stated that unit started making ice then the controls switch back and forth. Ordering main control in stock.; ordrng 1 W11034363 (ELEC CNTRL)
Tyler F.
REFRIGERATOR KITCHENAID KRMF706ESS01 Customer stated deli drawer is not working again. Found water under the display and wire harness has corroded. Ordering door and board. Customer is aware of door time frame.; ordrng 1 W10815668 (dor-fip bl) and 1 WPW10769076 (cntrl-elec)
Tyler F.
DISHWASHER WHIRLPOOL WDT750SAHZ0 "Customer stated that the unit keeps turning on and off by itself and door handle is scratched. Ordering handle, control and console not in stock.; ordrng 1 W11037340 (HANDLE) and 1 W11087207 (cntrl-elec) and 1 W11192367 (CONSOLE)"
Tyler F.
REFRIGERATOR KITCHENAID KBSD608EBS01 Need to replace dryer but don’t have sealed system equipment in a rental.
Tyler F.
OVEN WHIRLPOOL KEMS378SSS05 Customer stated that the microwave is not working. Found error code F6E0 for communication error.
Raymond H.
REFRIGERATOR WHIRLPOOL WRS321SDHZ02 "Upon arrival unit freezing in RC, inspected and found unit at proper temps, cx has items touching liner. Instructed cx on proper use and care of unit. Unit functions as designed."
Raymond H.
WASHER MAYTAG MHW6000XW0 Upon arrival unit would not operate but would light up. Unit would not start and was unresponsive to touch. Found bad UI Center. UI parts are no longer available. Unit non repairable.
Raymond H.
REFIRGERATOR WHIRLPOOL WRS588FIHZ00 "Upon arrival unit not making ice, inspected and found broken wires on lower harness. Unit needs door.; ordrng 1 LW11037738 (STAINLESS DOOR FC)"
Raymond H.
REFRIGERATOR WHIRLPOOL WRT511SZDB00 "Upon arrival cx stated FC keeps developing frost, and another company replaced the door and it is still frosting on liner. Found large gaps from cabinet to liner. Sealed unit with adhesive. Instructed cx to call back if frost continues. Unit functions as designed.; used 1 482338 (ADHESIVE) from stock"
Raymond H.
REFRIGERATOR WHIRLPOOL KSSC42QTS00 "Air wasn’t fully defrosted. Defrosted and broke loose all ice. Tested, verified temps were cooling in RC. Unit needs to regulate to normal."
Raymond H.
DISHWASHER KITCHENAID KDTE334GPS0 Upon arrival door hitting tub when closing. Leveled feet and rectified installation issues. Unit functions as designed.
Michael M.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Removed and replaced pump assembly. Rebooted unit and unit ops but not enough water is entering the u it before wash cycle begins. Verified 1-3 psi is being delivered to unit. Advised cx to call plumber and unit now ops as designed. Advised cx not to use unit until plumbing issue is corrected. Unit ops as designed job complete
Michael M.
REFRIGERATOR WHIRLPOOL MFI2569VEB2 Cx states ice maker is not making ice.Tech found ice maker mold with ice cubes in it. Removed ice maker and found styrofoam inside ice. Attempted to replace ice maker but supplied parts do not match installed parts. Needs ice maker pn WPW10190981; ordrng 1 WPW10190981 (icemaker)
Michael M.
REFRIGERATOR KITCHENAID KRFC300ESS01 Removed and replaced door. Swapped over door seal and handle. Removed drawers and used hot water to remove all ice build up. Door now seals as designed.Job complete
Michael M.
DRYER MAYTAG MGDC215EW2 "Cx states unit will not start.Interior lights function but not spinnn g.Found thermal fuse open. Removed and rep,aced with truck stock WP3392519Unit now ops as intended. Tech found dryer exhaust vent hose collapsed and wi5 holes on it. Found large amounts of lint built up.Explained to cx that pushing unit back as far as they are is causing the hose to become smashed and popping thermal fuse. Job complete; used 1 WP3392519 (THERMAL FUSE) from stock"
Michael M.
DISHWASHER WHIRLPOOL WDF540PADT1 Unit was not filling with water. Found float switch wiring pinched in two. Repaired wire connector and u it ops as designed. Ran unit through rapid advance and all ops are normal. Job complete
Michael M.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 Cx states ice maker stopped making ice.Tech tried service test 57 and ice maker would not harvest.Removed ice maker and replaced with new. New ice maker harvested and filled. Job complete
Kenneth M.
REFRIGERATOR WHIRLPOOL KSC23C8EYW00 Installed new right rear roller. Tested unit. Unit is working. Leak checked unit one last time. No leaks found. Unit is working properly. Customer approves function at this time.
Michael M.
REFIRGERATOR JENN-AIR JFFCC72EFS00 "Cx states ice maker still is not making ice.Tech verified correct revision Verified with tech line all service test passed, unit harvest and fills. Service test 120 passed with no issues. Can manually fill mold.Ice box fan runs on manual mode. Recommended replace Dispenser User Interface W11086558; ordrng 1 W11086558 (panel-ui)"
Kenneth M.
RANGE WHIRLPOOL WFE540H0ES0 Found unit with no power due to burned junction box. Customer will need the terminal block replaced. Also found cord frayed and need replacing. Customer supplied new power cord. Ordering terminal block. Further will be made once proper power is supplied to unit. ; ordrng 1 WPW10245259 (block-term)
Kenneth M.
OVEN WHIRLPOOL WOD51EC0AS04 Unit needs control board. Ordering new control board; ordrng 1 W10842982 (cntrl-elec)
Kenneth M.
DRYER MAYTAG MEDX655DW1 Found dryer squeaking due to bad roller belt pulley. Replaced dryer repair kit wi5 truck stock and tested unit. Unit is working properly. Customer approves function at this time. ; used 1 4392065 (DRYER REPAIR KIT) from stock
Kenneth M.
DRYER MAYTAG MEDB855DC4 Found unit DOA. Found 240 volts to unit but not powering on due to bad board. Ordering new control; ordrng 1 W11158453 (CONTROL)
Kenneth M.
OVEN WHIRLPOOL WMH32L19AS1 Unit not heating. Due to to bad magnetron. Magnetron is burnt out. Also noticed wires at transformer frayed and showing wire. Ordering new transformer; ordrng 1 W10844213 (magnetron) and 1 W10847161 (transformr)
Kenneth M.
DRYER ELECTRIC WHIRLPOOL WTW4816FW Found unit continuing to click. Found lid lock faulty. Ordering new lid lock and strike. Strike damaged. Missing metal prints in back for magnetize latch; ordrng 1 W10837741 (lid strike) and 1 W10838613 (lid lock assembly)
Kegan N.
RANGE WHIRLPOOL WFG320M0BB0 "Customer stated seemed like bulb socket was broken. Inspected unit, removed old light bulb. Broken connection found, reinstalled and inserted customer’s light bulb. Test good."
Kegan N.
DISHWASHER MAYTAG MDB4949SDZ0 "Customer stated that dishwasher not working properly. Cycle stops after fill, checked float switch for continuity, test good. Ordering main control board.; ordrng 1 W10906430 (cntrl-elec)"
Kegan N.
WASHER GENERAL ELECTRIC GTW330ASK3WW "Customer stated washer not finishing cycle. Tested unit, no drain, inspected pump, overheating, no clogs. Ordering drain pump.; ordrng 1 WH23X27574 (DRAIN PUMP)"
Kegan N.
REFRIGERATOR WHIRLPOOL WRF990SLAM02 "Removed and replaced parts, tested ice and water tested good. All works good this time."
Jim S.
WASHER MAYTAG MVWC416FW1 Water valve is split on the hot water side. Replaced valve unit tested ok
Kegan N.
DISHWASHER WHIRLPOOL WDT720PADM "Customer stated unit not advancing to next cycle. Inspected unit, diverter motor clicking, not moving. Ordering diverter motor.; ordrng 1 W10537869 (diverter mtr)"
Jim S.
DRYER MAYTAG MDG5500AWW Replaced open ignitor. Found gas coils not holding. Replaced gas coils; used 1 279311 (IGNITOR KIT & BRACKE) from stock
Jim S.
DRYER MAYTAG MGD5500FW0 Unit powers up but will not start. I do not hear the relay board coming on; ordrng 1 W10774832 (switch) and 1 W10875487 (cntrl-elec) and 1 W11123147 (motor-drve) and 1 W11189141 (SWITCH)
Jim S.
DRYER AMANA NED4655EW1 Replaced thermal fuse. Unit tested ok
Jim S.
RANGE FRIGIDAIRE FFEF3003NWD Repaired burnt wire at terminal connection.
Jim S.
COOK TOP - ELEC HOT POINT RB525H4WH Replaced switch and terminal blocks. Unit tested ok
Jim S.
OVEN DACOR MCS130S Rebuilt relay board
Jim S.
N/A N/A KUIC15NHZS0 Replaced board and drain pump. Clean light stays on. Recommend running the unit for three complete cycles
Jim S.
WASHER MAYTAG MVWC416FW0 The legs are missing from the washer and Lowe’s installed it for the customer. This is a customer instruct
Jim S.
DRYER WHIRLPOOL WED4815EW1 "Replaced motor, and start relay. Upon completion found that under a load ( there was no load before due to the bad motor ) the voltage drops to zero. Customer has a bad outlet"
Jim S.
OVEN KITCHENAID KOCE500ESS06 Customer states that the oven stops heating midway through cooking and that the cooling fan motor is noisy; ordrng 1 W10861504 (blower) and 1 W11093254 (panl-cntrl) and 1 W11188752 (FUSE)
Jim S.
DRYER WHIRLPOOL WGD4800BQ2 Replaced drum supports with tensioner and belt. Unit tested ok
James G.
REFRIGERATOR WHIRLPOOL WRS321SDHZ01 Replaced listed part due to noise Tested ok
James G.
REFRIGERATOR KITCHENAID KRFF507ESS01 Fresh food evaporator frozen ; ordrng 1 W11033168 (harns-wire)
James G.
WASHER WHIRLPOOL WFW75HEFW0 Dustin at tech line says replace main board Unit is connected properly and wiring is correct but unit is energizing valves backwards ; ordrng 1 W11201274 (CONTROL )
James G.
DRYER WHIRLPOOL WGD4800BQ0 Replaced listed part due to fuse open Tested ok
James G.
WINE COOLER KITCHEN AID KUWS24RSSS14 Motor is$110.00 plus changeClock is$89.00APPROVED ; ordrng 1 WPW10239390 (timer-def) and 1 WPW10299090 (motor-cond)
James G.
WASHER MAYTAG MHW8200FW0 Found dispenser arm not connected to motor also replaced listed part Tested ok
Irvin F.
WASHER GE GTW460ASJ5WW Removed power. Installed all parts. Completed assembly. Plugged unit in set Id. All ops normal.
Irvin F.
WASHER MAYTAG MVWC565FW1 "Water off on arrival. With water on valve is not shutting off or closing. Turned off all water. Replacing water valve, due to failed solinoid. ; ordrng 1 W11038689 (valve)"
Irvin F.
DRYER ELECTRIC WHIRLPOOL WED6400SW0 The unit is cold during operation. Found the element has a burnt spot at cut off connection. Installed element and fuse.powered unit and test passed. All ops normal.
Irvin F.
REFRIGERATOR KITCHENAID KRSF505ESS00 "The mold for the ice maker is twisted locked into position. Lost position. Replaced IM, no issues. All ops normal."
Irvin F.
WASHER WHIRLPOOL WFW72HEDW0 "Installed replacement suspension. Powered unit ran spin test, passed. All ops normal."
Irvin F.
M/W OTR WHIRLPOOL WMH31017HS2 "The turn table motor was moving in standby. Checked then switches found two weak switches. Replaced switches. Test for operation, food heats and turn table ok in Standby. ; used 2 W10727360 (MICROSWITCH) from stock"
Irvin F.
M/W OTR WHIRLPOOL WMH31017FB0 "Replaced cosmetically challenged door and control,cover. No issues. All ops normal."
Irvin F.
REFRIGERATOR FRIGIDAIRE LFHT1831QF2 "Replaced bulb and failed switch. Added power, door open light came on off when door switch depressed."
Irvin F.
WASHER WHIRLPOOL WTW8040DW0 F7/E9-locked rotor F0/E5-off balance F7/E5-shifter failure F2/E1-stuck keyCX says the unit is noisy and sound are not present. Splutch is the noise issue. The audible sounds not present from control. The unit is not spinning. ; ordrng 1 W10734521 (slider) and 1 W10754448 (clutch) and 1 W10858298 (console assembly.)
Irvin F.
REFER FRIGIDAIRE FFHT2032TP2 "FREZER is ice locked. Evap coils and rears area ice locked. Removed ice. Heater element checked ok. THE drain port was blocked, not allowing ice to melt thru to drip pan. Temps set to normal. Cooling."
Irvin F.
DISHWASHER KITCHENAID KDTE104ESS3 Removed power installed components. Ran test cycle. Passed. All ops normal.
Hector Z.
REFRIGERATOR WHIRLPOOL WRF535SMBM00 "Fresh food compartment getting too cold. Tested damper control and main control, both are working fine. Replaced thermistor. Tested ok."
Hector Z.
RANGE WHIRLPOOL WFG320M0BB2 Front burner heads having difficulty to ignite. ; ordrng 2 WPW10515455 (burnr-head)s
George Y.
WASHER MAYTAG MVWB835DW3 Installed parts tested check out ok complete no dents or dings cause by tech.
George Y.
DISHWASHER WHIRLPOOL KDTM404ESS1 Found dishwasher not washing sump pump humming need to replace. Sump pump assembaly Customer would like to think about call us back for r3pair do not order part.; ordrng 1 W10861526 (pump&motor)
George Y.
REFRIGERATOR ELECTROLUX EI26SS55GS1 Installed dispenser tested check out ok complete . No dents or dings cause by tech .
George Y.
DRYER MAYTAG MGDX655DW2 Found dryer working ok found exexively size of vent redshirted tested ok complete no dents or dings cause by tech.
George Y.
DRYER WHIRLPOOL WGD8500DC3 Found dryer working ok found exexively long dryer vent removed retested check out ok complete no dents or dings cause by tech.
George Y.
REFRIGERATOR KITCHENAID KRSC503ESS01 Installed part tested check out ok complete no dents or dings cause by tech.
George Y.
MICROWAVE WHIRLPOOL WMH73521CS-1 Installed parts tested check out ok complete no dents or dings cause by tech.
George Y.
WASHER WHIRLPOOL WFW85HEFW1 Found washer with no errors ran thrue quick wash tested ok reconnected control board connector ok . No dents or dings cause by tech.
Erick S.
WASHER ELECTROLUX EFLS617STT0 Cycled unit and found it leaking through bellow. It has small tear causing leak. Replaced bellow. Retested unit through test cycle and it passed all test with no leaks. Job complete; used 1 5304516744 (BELLOW) from stock
Erick S.
DRYER WHIRPOOL MDE7500AYW "Cycled unit and found unit with coins stuck in veins of drum causing noise. Took unit apart and removed coins. Re assembled unit, retested it with cust and unit is no longer making noise. Job comp"
Erick S.
WASHER MAYTAG MVWC565FW1 "Cycled unit and found it with no errors on board. Ran through tests cycle and it passed all tests with no errors. Cust not familiar with new style of washer. Instructed inform on energy and after efficiency. Instructed on proper loading,soap usage,and additional functions. Job complete"
Erick S.
DISHWASHER MAYTAG MDB4949SDZ0 Cycled unit and found poor drain. Found unit with bad pump causing it not drain correctly. Replaced pump. Retested it and it passed all tests with no errors. Job comp
Erick S.
WASHER HOT POINT HTW200ASK0WW Cycled unit and found it with door latch errr causing it not advance in wash. Replaced latch. Retested it and it passed all tests with no errors. Job complete ; used 1 WH01X27954 (LATCH) from stock
Erick S.
REFRIGERATOR FRIGIDAIRE LFHB2741PF5A Upon arrival found ice maker tray broken from ice maker shaft causing it not to make ice. Replaced ice maker assembly. Retested it and it passed all tests. Job comp
Erick S.
DRYER MAYTAG MGDX655DW Ycled unit and found it bad roller causing unit to make lots of noise while cycling. Replaced with repair kit. Retested it and it passed all tests with no Error. Job complete
Erick S.
N/A N/A GSS26C5XXY04 "Installed new part on unit. Retested it and unit now cooling in both sections, job comp"
Erick S.
RANGE GE JGBS10DEKWW "Cycled unit and found open wire through ignitor causing units burners not to ignite, both side will need to be replaced ; ordrng 2 WB18X26988 (spark electrode top)s and 1 WB18X31203 (SWITHC)"
Dane K.
WASHER MAYTAG MVWC565FW1 Upon arrival unit will not fill with cold water. Unit had long fill fault code. Removed and replaced valve and tested unit. Unit functions normal now
Dane K.
DRYER MAYTAG MGDB835DW0 Upon arrival of the unit was loud while running. Found rollers and pulley worn out and loud. Removed and replaced parts in dryer repair kit and tested unit. Unit functions normal now
Dane K.
DRYER AMANA NED4655EW1 Upon arrival the unit was not heating. Found thermal fuse open. Removed and replaced fuse and tested unit. ; used 1 3392519 (
Dane K.
REFRIGERATOR GE GSE25HGHWW Upon arrival the LED board and the fresh food assembly was burned out. Unit needs new fresh food LED assembly; ordrng 1 WR55X26671 (board led light assembly)
Dane K.
REFRIGERATOR WHIRLPOOL WRT311FZDW Unit was leaking due to frozen drain line. Defrosted drain line and installed prob.e and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR WHIRLPOOL WRS325SDHW00 Upon arrival the customer says there is a noise when the compressor was running. Found evaporator fan blade cracked and causing in a truce of noise when motor was running. Removed and replaced fan blade and tested unit. Unit functions normal.
Dane K.
DISHWASHER WHIRLPOOL WDF520PADM Upon arrival unit was not draining. Found drain pump burned out. Removed and replaced drain pump and tested unit. Unit functions normal however customer still has plumbing blockage leaving water in South causing dishes to stay wet. Unit functions normal
Dane K.
REFRIGERATOR WHIRLPOOL WRX735SDBM02 Upon arrival unit was freezing food. Remove and replace control and tested unit. Unit functions normal
Dane K.
DISHWASHER WHIRLPOOL WDF520PADM7 cx was a no show
William L.
DRYER WHIRLPOOL WGD85HEFW1 "F4E3, ran dryer cycle , could not detect noises."
William L.
WASHER WHIRLPOOL WFW92HEFW0 "Found no codes in unit, unit won’t pump out ran self diagnostics , unit won’t respond c00, ordered ACU brd & drain pump.; ordrng 1 W11201293 (ACU BRD) and 1 WPW10605427 (pump-water)"
William L.
RANGE WHIRLPOOL WFG540H0ES1 "found left front burner not lighting intermittently, ordered spark module & burner head & 15k orfic ; ordrng 1 W10178934 (orifice) and 1 WPW10347414 (spud-orfce) and 1 WPW10475149 (module-spk) and 1 WPW10515455 (burnr-head)"
William L.
REFRIGERATOR KITCHENAID KRMF706ESS01 "Replaced left bottom FF door hinge, adjusted doors, doors shutting as designed."
William L.
MICROWAVE KITCHENAID KOCE500ESS05 "replaced inverter brd, tested MV cooking functions several minutes, unit operating as designed."
William L.
DISHWASHER WHIRLPOOL WDT970SAHB0 "Replaced pump /motor assembly, ran test cycle, unit working as designed."
William L.
WASHER MAYTAG MVWB855DC0 "F9E1, F9E2, F0E5, unit not draining, drain pump humming won’ t pump water. ordered drain pump for unit.; ordrng 1 WPW10581874 (pump-water)"
William L.
WASHER MAYTAG MVWX655DW0 "removed washplate cleaned up splines on spindal, Replaced washplate,, ran self diagnostics, checked for code, no codes found, , unit operating as designed."
William L.
DRYER MAYTAG MEDB835DW3 "cx would will a different tech to finish repair of dryer, installed replacement belt, re-glued rear drum seal , found middle already replaced drum wheel making rattle noise, ordered replacement wheels & spindle. ; ordrng 3 WPW10314173 (support)s and 1 WPW10359272 (shaft)"
William L.
DRYER AMANA NED4600YQ1 "found drum rollers warm down, replaced roller with dryer repair kit, ran dryer cycle, tested ok; used 1 4392065 (DRYER REPAIR KIT) from stock"
Tyler F.
DISHWASHER WHIRLPOOL WDTA50SAHW0 Customer stated that the door is leaking. Found signs of leak but tested wi5 no leak. Ordering door seal in stock.; ordrng 1 W10300924V (door seal)
William L.
WASHER WHIRLPOOL MVWB850YG0 "Replaced bearing with bearing kit, ran spin test, ran self diagnostics, unit operating as designed."
William L.
DRYER WHIRLPOOL WGD85HEFC1 "Replaced outer door assembly, cx decided not get door reversed do washer door not being reversible, door functions as designed."
Tyler F.
DISHWASHER JENN-AIR JDB8700AWP3 Customer stated that dishwasher is still leaking. Cycle tested and could not recreate leak. Ordering door seal in stock.; ordrng 1 W10300924V (door seal)
Tyler F.
OVEN WHIRLPOOL KFGD500ESS01 Customer stated that the lower oven is not working found failed igniter. Ordering igniter in stock.; ordrng 1 WP7432P143-60 (igniter- b)
Tyler F.
DISHWASHER WHIRLPOOL WDTA50SAHZ0 Customer stated that the dishwasher was not washing dishes. Whirlpool sent customer sump assembly. Removed and replaced sump. Tested all works good at this time.
Tyler F.
WASHER MAYTAG MHW4200BW1 Customer stated that unit gives long drain code every cycle. Pump is clear could not replicate. Ordering control and pressure switch not in stock.; ordrng 1 WPW10448876 (switch-wl) and 1 WPW10689017 (cntrl-elec)
Tyler F.
REFRIGERATOR KITCHENAID KBFS20ECMS00 Customer stated that the ice maker is not working. Cycled ice maker did not call for water. Ordering ice maker in stock.; ordrng 1 W10884390 (icemaker)
Tyler F.
REFRIGERATOR WHIRLPOOL WRF767SDEM01 Customer stated that the ice maker is making too much ice. Found shut off arm was not in the ice maker. Fixed and tested all works good at this time.
Tyler F.
DISHWASHER WHIRLPOOL KDTE254ESS2 Customer stated that the interface will intermittently shut off mid cycle. Found connection between board and interface, Ordering interface and main control not in stock; ordrng 1 W10866124 (cntrl-elec) and 1 W10902370 (panel-cntl)
Tyler F.
RANGE WHIRLPOOL WFG540H0ES1 Customer stated that the two front burners are not lighting. Found igniters are working. Removed and replaced burner heads and cap kit tested all works good at this time.
Tyler F.
FREEZER WHIRLPOOL WRF540CWHZ00 Customer states freezer door is not sealing. Found door is sitting to high. Seal is too far away from cabinet to heat treat. Removed and replaced door tested all works good at this time.
Tyler F.
WASHER WHIRLPOOL WFW8300SW03 Customer stated that the unit keeps giving a long drain error code. Found debris in the drain pump. Removed debris and tested all works good at this time.
Tyler F.
REFRIGERATOR KITCHENAID KRSC503ESS01 Customer states ice maker still not working. Cycle tested ice maker found that unit only works when door is held at a certain spot. Voltage drops to ice maker when door is moved. Door has a broken wire in harness. Removed and replaced door. Tested all works good at this time.
Tyler F.
DISHWASHER WHIRLPOOL WDF330PAHB2 Customer stated that the fill hose is pinched from valve to tub. Removed and replaced fill hose tested all works good at this time.
Steven W.
WASHER WHIRLPOOL WTW5000DW1 Ran diagnostics. Had f8e3 error. Cleared error code. Found lid strike spring weak. Needs lid strike. Will P/U part from coast south El Monte.; ordrng 1 W10837741 (lid strike)
Steven W.
DISHWASHER AMANA ADB1400AGS1 Leaking.Found wash pump missing sump tabs. Needs pump & motor. ; ordrng 1 W10888591 (pump and motor)
Steven W.
REFRIGERATOR WHIRLPOOL WRX988SIBM01 Still intermittent. Per tech line order shim pad for left door switch. Needs switch and spacer.; ordrng 1 12002646 (light switch) and 1 WPW10221048 (spacer)
Steven W.
DISHWASHER KITCHENAID KDFE104DSS5 "Ran diagnostics. Had 7-1 fault code. Needs control, heater.; ordrng 1 W10703867 (heater) and 1 W11084330 (cntrl-elec)"
Steven W.
WASHER MAYTAG MVWX655DW1 "Ran diagnostics. No error codes found. Ran calibration, auto test cycle- passed. No hot water. Advised customer to call plumber. Unit must have hot & cold water to work properly. Fills, agitates, drains, rinses,& spins properly. Advised customer to use only HE liquid or pod detergents. Complete."
Steven W.
WASHER MAYTAG MVWB835DW4 "Ran diagnostics. Had f0e4, f0e5 error codes. Cleared error codes. Instructed customer on unbalanced loads, proper loading. Load tested on rinse & spin. Fills, agitates, drains, rinses,& spins properly. Advised to wash like items together, do medium to large loads( no small loads ). Unit is working as designed. Complete."
Steven W.
DISHWASHER KITCHENAID KDPE234GPS0 "Found upper spearman’s fell off. Replaced retainer & upper spray arm. Fills, washes, drains,rinses, dries properly at this time. Complete."
Steven W.
DISHWASHER AMANA ADB1400AGW1 "Ran diagnostics. Had 8-2 fault code. Found drain motor harness plug not inserted all the way into drain motor. Reinserted/ recrimped plug. Ran test cycle- passed. Fills, washes, drains, rinses, and dries properly. Advised customer to purge hot water line before starting DW. Complete."