We serviced a
WHIRLPOOL RANGE
Model WFE320M0JS3
Near Bakersfield, CA 93307
Raymond
Job Details: 09/27/2023
"Cx states a noise heard intermittently, had apartment maintenance out and they saw a black spot they said was burning or arcing, inspected and found no damage to the plastic housing, black spot was just debris from manufacturing, wiped off of infinite switch and no overheating found. Advised cx to record intermittent noise."
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE304LPA1
Near Los Angeles, CA 91364
Felipe S
Job Details: 09/27/2023
Install the new pump on the unit. Retest the unit and now unit is working properly. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Hanford, CA 93230
Enrique
Job Details: 09/27/2023
"RC freezing sodas, eggs on top shelves. replaced damper control (open). Ran test. Refrigerator operating properly at time of service."
We serviced a
KITCHEN AID REFRIGERATOR
Model KRSF705HPS00
Near Madera, CA 93638
Irvin
Job Details: 09/27/2023
"Removed power from fridge. Cleaned out gunk, installed components. Assembled unit, restored power. All ops normal. DONE."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Porterville, CA 93257
J.E.
Job Details: 09/27/2023
Cycled unit and found F0E7 indicating load detected while running clean washer cycle. Instructed customer on proper loading and cycle selection. Unit is working as design job completed.
We serviced a
WHIRLPOOL WASH/DRY COMBO
Model WGT4027EW1
Near Los Angeles, CA 91607
Leon
Job Details: 09/27/2023
Cx states that unit is not heating up After running diagnostic test find that unit has a broken belt. Job is completed
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM3160DF8WW
Near Oxnard, CA 93033
Kenneth
Job Details: 09/27/2023
Installed fuse assem and magnetron assem. Tested. Unit is working properly. Customer approves function at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Victorville, CA 92395
Drew M.
Job Details: 09/27/2023
Replaced ice maker and ran cycle unit passed all tests and the noise is no longer present.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near El Monte, CA 91733
Stephen
Job Details: 09/27/2023
"Ran diagnostics. Reset temps. Vibration sound when compressor is running. Found tubing vibrating. Adjusted compressor tubing, installed cork tape on tube. Unit is cooling properly at this time. Instructed customer to have old clear water supply tubing replaced with copper or PEX tubing by plumber. Complete."
We serviced a
WHIRLPOOL DRYER
Model MGDX655DW2
Near Camarillo, CA 93010
Ian Y
Job Details: 09/27/2023
installed new timer in unit. Set on a time dry. Units timer is now working as designed.
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Manteca, CA 95336
William
Job Details: 09/27/2023
"Replaced run cap & main control brd, ran self diagnostic cycle, unit operating as designed."
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GNE27JYMWFFS
Near Dos Palos, CA 93620
Jonathan
Job Details: 09/27/2023
Tested found unit needs firmware updated tested working properly
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAHZ0
Near Azusa, CA 91702
Jaime
Job Details: 09/27/2023
Per take support to use glass door. W11179175. to see where the leak comes from. It appears as if water level goes above normal level. Replaced float switch and all parts around it
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Riverside, CA 92508
Ruben O
Job Details: 09/27/2023
Replaced loud damper control. Tested after repair all ok no more noise.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Caruthers, CA 93609
Doug S
Job Details: 09/27/2023
"unit had broken strike, replaced from truck stock ; used 1 W11457841 (strike) from stock"
We serviced a
MAYTAG WASHER
Model MVW7230HC0
Near Los Angeles, CA 91306
Bob S.
Job Details: 09/27/2023
Removed old unit. Installed new unit. New unit operated as designed.
We serviced a
MAYTAG MICROWAVE
Model MVWP575GW1
Near Shafter, CA 93263
James
Job Details: 09/27/2023
Removed and installed new agitator. Unit now working as intended.
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model GWE19JYLEFFS
Near Fresno, CA 93727
Doug S
Job Details: 09/26/2023
installed new door seal and tested unit working as designed
We serviced a
WHIRLPOOL DRYER
Model WGD5010LW3
Near Bakersfield, CA 93312
Brandon
Job Details: 09/26/2023
Installed new parts and correct all noise issues. Unit is running as designed.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS01
Near Malibu, CA 90265
Felipe S
Job Details: 09/26/2023
"Upon arrival found unit with bad damper causing the control having issues. Replace the damper on the unit, retest the unit and now unit is working properly. Job complete"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Camarillo, CA 93010
Kenneth
Job Details: 09/26/2023
Installed control and tub ring. Tested unit. Unit is working properly. Customer approves at this time.
We serviced a
WHIRLPOOL WASHER
Model WFW70HEBW2
Near Claremont, CA 91711
Jaime
Job Details: 09/26/2023
Replaced a noisy drain pump. Washer Ok Parts
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KBL2
Near Camarillo, CA 93012
Ian Y
Job Details: 09/26/2023
"Swapped out units control, unit is now responding to touch and working as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Tulare, CA 93274
Enrique
Job Details: 09/26/2023
"Customer concerns: freezer/refrigerator not cooling (prior service, rc was freezing food). Faulty control box. Replaced control box. Refrigerator operating as designed. RC temperature 39-40 degrees. Different problem from previous visit."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Santa Clarita, CA 91355
Randy
Job Details: 09/26/2023
Cx unit did not fill bin after 12 hours. Cx wants unit to produce more ice. Filled up only 1/3 of the way overnight. Not enough per customer. Cx instruct on use. Unit takes longer to fill up. Unit is working as designed. No issues.
We serviced a
KITCHENAID RANGE
Model KSDG950ESS1
Near South Pasadena, CA 91030
Stephen
Job Details: 09/26/2023
Ran diagnostics. Has f2e0 error code. Keypad is connected. Needs control panel( console ) and keypad harness. Needs W10915031 console and W11025616 keypad harness. Customer to call Whirlpool customer service for concession.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Bakersfield, CA 93314
Jim
Job Details: 09/26/2023
Replaced tub assembly
We serviced a
WHIRLPOOL RANGE
Model KFGD500EWH10
Near Moreno Valley, CA 92553
Kevin
Job Details: 09/26/2023
Removed and replaced hinges. Tested unit. All tests good.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMC2273CF00
Near Bakersfield, CA 93309
Aaron
Job Details: 09/26/2023
"Complaint was the freezer last week had an ice build up, as a result would not close all the way and seal correct. Opened the door, cleared the ice and heated the door gasket to seal correct. Operations ok now at this time"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB01
Near Bakersfield, CA 93312
Brandon
Job Details: 09/26/2023
Installed new parts. Water is now dispensing. Icemaker is now filling.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Nipomo, CA 93444
George
Job Details: 09/26/2023
Installed part tested check out ok complete no dents or dings cause by tech.
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE104ESS3
Near Los Angeles, CA 90041
Oscar L
Job Details: 09/26/2023
"Visual and physical plus mechanical inspection was performed leading to a few issues, touch panel is not always responsive, even when all wash arms are debris free, wash pump is very weak, plus not drying anymore. Because of a night cost repairing, consumer opted to replace unit instead."
We serviced a
GE RANGE
Model PGP953DET2WW
Near Taft, CA 93268
James
Job Details: 09/26/2023
Replaced defective left front knob.
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Tracy, CA 95376
William
Job Details: 09/26/2023
"Replaced motor , blower wheel & belt, ran dryer cycle, unit operating as designd."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHV06
Near Ventura, CA 93003
Isidro
Job Details: 09/26/2023
"Some condensation on top,of freezer door gasket, I remolded both door gaskets with heat gun, unit is now sealing properly as designed, customer approved repairs"
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Cambria, CA 93428
Paul V
Job Details: 09/26/2023
Removed existing strike. Installed new strike. Unit operating as designed.
We serviced a
GE WASH/DRY COMBO
Model GUD27GESN0WW
Near Cayucos, CA 93430
Paul V
Job Details: 09/26/2023
Diagnostic check. Volts/amps disconnected furnace control board deenergized unit re-energized unit test ran unit unit making noise due to being sit on a wooden pallet. Unit operating as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near San Bernardino, CA 92404
Francisco
Job Details: 09/26/2023
"Removed and replaced compressor and evap, vacuumed and recharge up to 68 g of r600 a. Asked cx to allow 24-48 hrs for normal ops"
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS04
Near Santa Maria, CA 93455
George
Job Details: 09/26/2023
Installed part tested check out ok complete no dents or dings cause by tech.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ07
Near Agoura Hills, CA 91301
Richard R
Job Details: 09/26/2023
Upon arrival inspected unit replaced both cams top and bottom on the left on unit and adjusted the leveling on it unit is now working as it should job completed
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Santa Maria, CA 93455
George
Job Details: 09/26/2023
Installed parts tested check out ok complete no dents or dings cause by tech.
We serviced a
MAYTAG WASHER
Model MHW8630HC4
Near Bakersfield, CA 93311
Chase
Job Details: 09/26/2023
Installed new pump. All ops now working as designed.
We serviced a
JENN-AIR RANGE
Model JES1750ML0
Near Modesto, CA 95355
Martin R
Job Details: 09/26/2023
Replaced Acu tested unit all functions are working per design job complete
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Riverside, CA 92506
Robert U.
Job Details: 09/26/2023
Found the unit not heating properly. Found the operating thermostat not working properly and the heating element is weak. I replaced all parts minus the thermal fuse because that was good. All functions tested ok. Job completed.
We serviced a
MAYTAG DRYER
Model MGD7230HC3
Near Santa Clarita, CA 91354
Randy
Job Details: 09/26/2023
Maytag dryer long dry times on towels. Tested no error codes. Tested and checked vent. All ops normal. Vent could use more airflow. Referred customer to open vent or replace w a flap/vent w openings. Took pics Cx instruct on load and use. Unit is working as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB08
Near Sanger, CA 93657
Timothy
Job Details: 09/26/2023
Installed IM and tested. IM checks ok. Cycled IM multiple times and checked water for cloudiness. None noted.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ03
Near Modesto, CA 95355
Timothy G
Job Details: 09/26/2023
Replaced control and ui together per whirlpool. Tested unit and unit passed all tests as usual. Now waiting to see if ice maker continues to produce ice .
We serviced a
GENERAL ELECTRIC DISHWASHER
Model CDD420P2T0S1
Near Bakersfield, CA 93306
Brandon
Job Details: 09/26/2023
Unit panel was locked. Cx instruct on panel controls and showed her how to lock/unlock the controls. Unit is working as designed.
We serviced a
ELECTROLUX WASHER
Model ELFW7637AT1
Near Turlock, CA 95382
Cruz
Job Details: 09/26/2023
File # 86683870 from Frigidaire tech line- f5e5 OOB- cx is over loading causing error code- auto test pass- spin test pass as well- informed cx and loading techniques- unit working per design-
We serviced a
WHIRLPOOL DISHWASHER
Model KDFE204KPS1
Near Topanga, CA 90290
Felipe S
Job Details: 09/26/2023
"Upon arrival according with the department, the unit sometimes shuts down, and the breaker turns off because the dishwasher. This information was provided by the electrical company, this because the outlet was replaced 2 time already. Check the unit and unit doesnt have any error codes, run the unit trough diagnostic and found the unit is working properly. Check the outlet and found water drip on the outlet, this water comes from unknown source. Inform this to the department. Job complete."
We serviced a
WHIRLPOOL FREEZER
Model WRF757SDHV04
Near Bakersfield, CA 93312
James
Job Details: 09/26/2023
Replaced components and unit now working as intended.
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW0
Near Rosamond, CA 93560
Jonathan B.
Job Details: 09/26/2023
"JB out 9/26/23. Customer stated that the spin cycle takes a very long time to end. Sometime the unit will spin one or two hours or longer. Upon arrival found unit in spin mode. After about ten minutes, the cycle ended. Removed all clothes and tested Spin with no clothes, verified unit did spin smoothly and to proper spin speed. Reloaded washtub with clothes and unit did spin at high speed smoothly and made no noises.Recommend from today going forward to use very small amount of he detergent typically ONE MEASURED TEASPOON MAXIUM. Also to carefully load clothes in loose heaps evenly around the WASHPLATE maintaining that the center hub stay uncovered ( this is a loading guide).Recommend against use of the Turbo detergent and pods as both are too highly concentrated for this low fill, high efficiency washing machine. Unable to verify any mechanical defects today.NO CHARGE TO CUSTOMER JOB COMPLETE"
We serviced a
JENN-AIR DISHWASHER
Model JDPSS246LL0
Near Camarillo, CA 93010
Ian Y
Job Details: 09/26/2023
Replace units control and console. Unit now responds to touch and will go into cycles.
We serviced a
KITCHENAID RANGE
Model KSGG700ESS0
Near Thousand Oaks, CA 91362
Richard R
Job Details: 09/26/2023
"Upon arrival inspected unit consumer stated that when the unit is put into broil, it seems to not reignite and not cooking properly. I replaced the igniter and the spark module for the broiler tested unit unit seems to be working as it should advise customer to always put the product in before it gets to 500 to ensure proper searing during broiling unit working as intended job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Santa Clarita, CA 91351
Randy
Job Details: 09/26/2023
Removed and replaced cam and hinge. Installed door. Tested now working as designed
We serviced a
KENMORE WASHER
Model 110.47566601
Near Rancho Cucamonga, CA 91739
Tyler
Job Details: 09/26/2023
Customer stated that the unit is making a bunch of noise in spin. Found front bulkhead missing a screw causing vibration in panel. Fixed and tested all works good at this time.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS02
Near Bakersfield, CA 93312
Brandon
Job Details: 09/26/2023
Installed new parts. Unit was working as designed after service.
We serviced a
KITCHENAID DISHWASHER
Model KDTM704KPS0
Near Altadena, CA 91001
ERICK H
Job Details: 09/26/2023
Replaced sump assembly. Tested unit. Unit operating as designed. Job complete.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Rialto, CA 92376
Robert U.
Job Details: 09/26/2023
After replacing all parts the unit is no longer making the abnormal clicking noise. All functions are working properly. Job completed.
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Bakersfield, CA 93307
Raymond
Job Details: 09/26/2023
"Installed sump assembly and tested, unit functions as designed."
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ0
Near Fresno, CA 93727
Irvin
Job Details: 09/26/2023
Replaced the door latch. Assembled unit restored power. Ran and passed calibration cycle. Started unit in normal cycle. MIXED/WARM. Unit fill and is operational. DONE.
We serviced a
ROPER DRYER
Model RGD4516FW
Near Planada, CA 95365
Nathaniel C
Job Details: 09/26/2023
Installed new timer and knob all functions tested okay. Unit working as designed . Call complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRV986FDEM01
Near Glendale, CA 91205
Oscar L
Job Details: 09/26/2023
"Last piece on the equation has been fulfilled (UI), and per previous technician, icebox, Icemaker (x2).Unit is passing all testes 57, 45, 58, 59 and no errors codes. Consumer was asked to allow at least 24 hours for proper operation."
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ2
Near Camarillo, CA 93012
Kenneth
Job Details: 09/26/2023
LED panel and tested unit. Unit is working properly. Customer approves function at this time.
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Los Angeles, CA 91331
Dane
Job Details: 09/26/2023
Unit had bad suspension. Removed and replaced suspension and tested unit. Unit functions Romano.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Monrovia, CA 91016
Daniel G
Job Details: 09/26/2023
Got to Cx home we removed old unit old unit was not building condensation between doors. Brought in new unit tested new unit operating as designed job complete
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Manteca, CA 95337
William
Job Details: 09/26/2023
"Replaced pump/motor, ran self diagnostic cycle, unit operating as designed."
We serviced a
WHIRLPOOL RANGE
Model WOS31ES0JS20
Near Manteca, CA 95337
Bob S.
Job Details: 09/26/2023
Cx states Fan and wont stay on. Removed old unit installed new unit new unit operating as designed.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Los Angeles, CA 91607
Leon
Job Details: 09/26/2023
Cx states that unit is not working properly Cx states that unit is not cooling properly Replaced selected partUnit working properly as required
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Bakersfield, CA 93304
Chase
Job Details: 09/26/2023
"F0e4, f8e1. Flushed valve and programmed board. All functions now working as designed."
We serviced a
MAYTAG WASHER
Model MAT20PDAWW1
Near Merced, CA 95341
Nathaniel C
Job Details: 09/26/2023
Installed new coin drop assembly. All functions tested okay. Unit working as designed. Call complete.
We serviced a
GENERAL ELECTRIC DRYER
Model GTD33GASK1WW
Near Bakersfield, CA 93313
Chase
Job Details: 09/26/2023
Installed new part. All ops now working as designed. Documented previous damage with pic. This was from install. All ops with machine checking ok.
We serviced a
JENN-AIR COMPACTOR
Model TC607X4
Near Los Angeles, CA 91326
Felipe S
Job Details: 09/26/2023
Install the new pedal and main switch nub on the unit. Retest the unit and now unit is working properly. Job complete
We serviced a
MAYTAG WASHER
Model MVWX655DW
Near Los Alamos, CA 93440
George
Job Details: 09/26/2023
Found washer testing out ok customer concern with tub vibration customer in mobile home unit functioning as design complete no dents or dings cause by tech.
We serviced a
GENERAL ELECTRIC DRYER
Model PTD60GBSR1WS
Near Wasco, CA 93280
James
Job Details: 09/26/2023
Installed new harness and tested unit. Unit is heated no and working as intended.
We serviced a
WHIRLPOOL OVEN
Model WOD51EC0HS20
Near Reedley, CA 93654
Timothy
Job Details: 09/26/2023
One of the L1 connections in one of the electrical boxes behind the unit. If this should reoccur the customer should get an electrician.
We serviced a
ELECTROLUX DRYER
Model EFME627UTT2
Near Riverbank, CA 95367
Andrew H
Job Details: 09/26/2023
Noisy bearings. Belt and Idler pulley fault. Operation according to design.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Hanford, CA 93230
Enrique
Job Details: 09/26/2023
Replaced new parts. dryer operating as designed.
We serviced a
WHIRLPOOL WASHER
Model MVW6200KW0
Near Burbank, CA 91501
Leon
Job Details: 09/26/2023
Replaced all selected parts Unit working properly as required
We serviced a
MAYTAG WASHER
Model MVWB765FW4
Near Upland, CA 91786
Tyler
Job Details: 09/26/2023
Customer stated that the unit is leaking. Found leak is coming from the dispenser. Removed and replaced dispenser tested all works good at this time.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Oakdale, CA 95361
Martin R
Job Details: 09/26/2023
Replaced pump and motor tested unit it is filling washing and draining with no leaks Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC704FPS06
Near San Dimas, CA 91773
Alejandro
Job Details: 09/26/2023
"Found the unit, not cooling, verify problem, compressor not working, replace compressor and service valve make a vacuum, charge refrigerant 56g R600a, check compressor condenser and evaporator fan motors, unit work normal"
We serviced a
JENN-AIR OVEN
Model JMW2427DS01
Near Los Angeles, CA 91606
Oscar L
Job Details: 09/26/2023
"Because of stubborn Error code F2E1, a new appliance manager and console were replaced.Unit was tested successfully to customers satisfaction."
We serviced a
FRIGIDAIRE DISHWASHER
Model FGID2468UD1A
Near Bakersfield, CA 93314
Chase
Job Details: 09/26/2023
Found wheel popped off and was caught underneath float switch. Removed object from float switch. Unit now running a complete cycle and working as designed.
We serviced a
MAYTAG WASHER
Model MVW7232HW
Near Simi Valley, CA 93065
Paul M
Job Details: 09/26/2023
"Unit rub was dropped to the floor, suspension rods were non existent. Front two had broken off, tub lid was damaged. Replaced all parts, ran all calibration modes, ran diagnostics mode and checked for error codes. Unit is now working as designed, job complete."
We serviced a
MAYTAG WASHER
Model MHW5630HC1
Near Taft, CA 93268
James
Job Details: 09/26/2023
Replaced defective door bellows.Tested ok
We serviced a
JENN-AIR RANGE
Model JGRP536HL00
Near Santa Paula, CA 93060
Kenneth
Job Details: 09/26/2023
Installed main control and UI control. Also installed light button. Tested unit. Unit is working properly. Customer approves function at this time.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Delano, CA 93215
James
Job Details: 09/26/2023
Installed new drawer and control. Calibrated and tested. Unit now working as intended.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS09
Near Manteca, CA 95337
Andrew H
Job Details: 09/26/2023
Display faulty. Reset PCM board. Operation according to design.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Bakersfield, CA 93314
Aaron
Job Details: 09/26/2023
"Replaced the right side door upper and lower cams and hinge asm , tested operating ok now at this time"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KBSD608ESS01
Near Bakersfield, CA 93314
James
Job Details: 09/26/2023
Replaced all leds modules under special program S-84638; used 4 W11632139 (Module) from stock
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Moreno Valley, CA 92553
Kevin
Job Details: 09/26/2023
"Removed and replaced gearcase, cam, belt, suspension, hub and actuator. Tested and calibrated unit. All tests good."
We serviced a
MAYTAG WASHER
Model MVWB865GC1
Near Newberry Springs, CA 92365
Drew M.
Job Details: 09/26/2023
Found harness loose. Replaced harness and ran cycle. Unit passed all tests and is operating as designed.
We serviced a
MAYTAG DRYER
Model MGD7230HW
Near McFarland, CA 93250
James
Job Details: 09/26/2023
Installed new repair kit and seal unit completed.
We serviced a
GENERAL ELECTRIC RANGE
Model PGS930YP5FS
Near Apple Valley, CA 92308
Drew M.
Job Details: 09/26/2023
Replaced parts and ran cycle. Unit passed all tests and is operating as designed.
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Visalia, CA 93291
J.E.
Job Details: 09/26/2023
Cycled unit and found suspension came off causing off-balance. Reinstalled and secured suspension unit not working as designed job completed.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAMS0
Near South El Monte, CA 91733
Stephen
Job Details: 09/26/2023
"Replaced pump&motor, power cord. Cleared error codes. Poured water into tub for testing- no water connections. Washes, drains, rinses, and dries properly at this time. Complete."
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Lompoc, CA 93436
George
Job Details: 09/26/2023
Found washer leaving clothes wet at end of wash found too much soap used clear out retest ok complete no dents or dings cause by tech.
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near McFarland, CA 93250
James
Job Details: 09/26/2023
Replaced drain pump and unit now working as intended.
We serviced a
WHIRLPOOL WASHER
Model MVW6200KW2
Near Merced, CA 95340
Cruz
Job Details: 09/26/2023
"Fixed- cx states wash basket seem lose and its hitting side walls- removed wash plate , found spanner nut to be lose causing basket to hit sides walls, tightened spanner, nut reattached wash plate tested, no shaking, no hitting side walls- calibration test pass as well- unit working per design- cx ok repair"