Local Reviews
Powered by Fluid LOCAL
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFTR1222QB Installed evap motor and tested unit. Unit is now working properly. Customer approves function at this time.
Kenneth M.
MICROWAVE JENN-AIR JMC2430DS01 Installed glass door. Tested. Unit is working properly. Customer approves function at this time
Jesus C.
DRYER WHIRLPOOL WGD4815EW2 "Customer states that unit is not heating. Ran unit and gas valve not opening. Removed back cover and tested components. Raised top panel and removed front panel. Removed drum and placed jumper on door switch. Placed amp meter on ignitor and turn unit on, found the ignitor at 4 amps. Need to replace the coils. Ordered parts. ; ordrng 1 WPW10328463 (coil-valve)"
Kenneth M.
WASHER WHIRLPOOL MODEL
Kenneth M.
WASHER WHIRLPOOL WTW5000DW1
Kenneth M.
DISHWASHER KITCHENAID KDTE104ESS4 Installed sump assem and drain pump and tested unit. Unit is now working properly. Customer approves function.
Jesus C.
DRYER WHIRLPOOL WED7500VW2 Customer states that unit is continuously srying on. Ran unit on timed dry and not advancing. Also the noise level on dryer. Noise level on unit is normal; ordrng 1 W10909677 (element) and 1 WPW10404695 (timer)
Jim S.
RANGE GE JGRP20WEJ2WW Replaced bake ignitor. Unit tested ok
James M.
WASHER MAYTAG MHW5630HW0 Found unit not advancing cycles. Checked acu and found LED continually blinking with ACU failure. Ordering new acu. F7e2; ordrng 1 W11322901 (ACU)
Jim S.
WASHER WHIRLPOOL WTW8540BW1 "Replaced board, harness, sensor, and motor. Ran calibration test. All test ok"
Jim S.
MICROWAVE KITCHENAID KHMS2056SWH1 Replaced magnetron and inverter. Unit tested ok
James G.
DISHWASHER KITCHENAID KDTE334GPS0 No show confirmed
James G.
REFRIGERATOR FRIGIDAIRE FGSS2635TF0 Compressor pulling.4 amps no Freon; ordrng 1 241650211 (compressor & gromm) and 1 5303918284 (evaporator)
James G.
COOKTOP WHIRLPOOL GLT3057RB01 Unit will also need right rear burner and base
Jim S.
REFRIGERATOR KITCHEN AID KSRU25FKBT03 It was banks icemaker not working. The motor was just frozen. Defrost a motor unit working
Jesus C.
MICROWAVE KITCHENAID KOCE507EWH06 Customer states that unit microwave light not working. Turned power off and pulled unit out 6 inches. Removed UI panel and raised appliance manager. Removed basles and installed new. Assembled unit and placed back in place. Turned power on and tested light. Unit is now working as design.
James G.
WASHER MAYTAG MHW7100DW0 Board not powering cold valve 1; ordrng 1 W11029154 (cntrl-elec)
Jesus C.
DISHWASHER WHIRLPOOL WDF520PADW7 Customer states that unit is it cleaning dishes properly. Ran test and found error code. Ran full test and no issues found. Unit is now working as design. 5-2 Door stuck closed
James G.
FREEZER KITCHENAID KRMF706EBS01 Now motor not running ; rqstng P&A on 1 W10822606 (motor)
Jesus C.
DISHWASHER MAYTAG MDB4949SHZ0 Removed lower panel and disconnected connector. Turned water valve off and removed intake valve connector. Checked power and getting 118 vac. Removed hose and replaced the valve. Plugged unit back on and water not coming out. Turned water off from main valve at home and removed hose from both ends. Customer valve under sink not closing completely. Found the inlet hose clogged. Removed debris and installed hose back. Turned main valve on and tested unit. Ran diagnostics and passed. 6-1 low or no water
James G.
MICROWAVE WHIRLPOOL WMH32519HV1 Sensor not working on potato setting ; ordrng 1 W11221051 (BOARD ) and 1 W11333816 (BOARD )
Jesus C.
KITCHEN WHIRLPOOL WDT720PADM2 Customer states that unit is not working. Found unit with error code not listed on tech-sheet. Unplugged unit and removed UI panel. Plugged back in ant not responding. Removed control board and installed new. Assembled unit and tested. Unit is now working as design.805-346-5954F2-E2
Jesus C.
MICROWAVE WHIRLPOOL WMH31017HS0 "Unplugged unit and removed from cabinet. Removed microwave housing. Found the capacitor shorted, installed new capacitor and tested. Unit is still not heating. Removed hv diode, magnetron and installed new parts. Placed cusp of water and tested. Assembled unit and placed back in cabinet. Unit is now working as design."
James G.
DRYER MAYTAG MGDB835DW4 No heat and vent is crushed advised customer she will need to correct vent issue ; ordrng 1 W10909685 (fuse-thrml) and 1 WP338906 (sensor) and 1 WP3391912 (thrmst-fix) and 1 WP8573713 (cutoff-tml)
James M.
WASHER WHIRLPOOL WTW4816FW Replaced water inlet and tested unit. U it passed all auto testing and is functioning as intended. With no leaking at this time.
James M.
WASHER MAYTAG MVWB835DW3 "F8e1, f3e2, f7e0, f0e3, f2e1. Fund unit not allowing hot water into unit due to bad water inlet. Replaced inlet and tested unit. Unit now functioning properly and no errors."
James M.
REFRIGERATOR FRIGIDAIRE FFSS2614QP Replaced valve and icemaker filled as intended with no leaks. U it is now working as intended and customer approves.
James M.
FREEZER WHIRLPOOL WRX735SDHZ00 Unit icemaker producing too much ice and not shutting off when full. Replaced icemaker from truck stock. Unit is working as intended.
James G.
REFRIGERATOR KITCHENAID KRMF606ESS01 Replaced listed part Tested ok
Chase F.
RANGE WHIRLPOOL WFG320M0BS3 "Diagnosed unit, found that all burners light up besides front left. Ordering parts for repair ; ordrng 1 WP6610341 (module-spk) and 1 WPW10515455 (burnr-head) and 1 WPW10548355 (harns-wire)"
James G.
WASHER WHIRLPOOL WTW7500GW0 Replaced control due to f7/e0Also referred customer to page 17 and 19 of use and care guide
Chase F.
RANGE GE JGBS30REK2SS "Checked for 120 volts to ignitor and getting proper voltage. Ordering 1 ignitor .; ordrng 1 WB13K21 (ignitor,oven)"
James G.
REFRIGERATOR KITCHENAID KRMF706ESS01 No noise at time of visit. Customer says freezer door may have been left open
Chase F.
WASHER MAYTAG MHW8200FC0 Diagnosed unit. Found that detergent would not come out. Ordering parts for repair; ordrng 1 W10250743A (dispenser)
Chase F.
DISHWASHER WHIRLPOOL WDTA50SAHZ0
Cesar H.
DRYER ELECTRIC MAYTAG MVWB835DW0 Received a control for a dryer not a washer reordering ; ordrng 1 W11100602 (cntrl-elec)
James G.
WASHER HOT POINT HTW200ASK0WW Replaced listed parts Tested ok
James G.
DRYER WHIRLPOOL WGD9400SZ2 Replaced listed part Tested ok ; used 1 3392519 (
James G.
REFRIGERATOR WHIRLPOOL WRX735SDBM00 Replaced listed part Tested ok
James G.
REFRIGERATOR FRIGIDAIRE FFHT1514TW3 Replaced listed parts and charged to 4.25 oz 134aTested ok
James G.
WALL OVEN GE ZSC2001FSS01 Replaced listed part ; used 1 WB27X10283 (FUSE) from stock
Irvin F.
OVEN KITCHEN AID KEBS109BSS00 "Removed power. Installed replacement fuse. Completed returning un8t to hole. Powered and test for operation, passed. All ops. Normal."
Billy J.
WASHER WHIRLPOOL WTW7500GC0 Upon arrival cx stated unit is very load found units gearcase is completly gone and dripping oil I tested unit and was also receiving a shifter error code as well I cleared and retested but it came right back up unit needs gearcase and shifter; ordrng 1 W10754448 (clutch)
Irvin F.
MICROWAVE KITCHENAID KEMS308SSS04 "Removed power. Replaced inverter, and mag. Test for operation, heating. Returned unit to hole test again, passed. All ops normal."
Billy J.
REFRIGERATOR WHIRLPOOL WRT311FZDW01 Control box does not come with control ordering control W11263188; ordrng 1 CONTROL (CONTROL)
Chase F.
WASHER MAYTAG MVWB835DW1 "Received an off balance error code. Checked for weak suspension. Suspension is good. Calibrated unit, instructed cx on how much to load and how to load evenly. Also instructed cx on proper amount of soap to use and all other specifics on how to use machine. Unit is now calibrated and running a complete cycle."
Chase F.
WASHER WHIRLPOOL WTW7000DW3 "Installed new lid lock. Lid now locking with no problems, Ran unit through calibrations. Tested unit. Unit now running a complete cycle, and working by design."
Chase F.
WASHER AMANA NTW4605EW0 Installed new gear case and agitator. Unit now running complete cycle and working by design.
Aaron B.
REFRIGERATOR KITCHENAID KRSC500ESS01 Checked operations unit has a frozen up evaporator again unit needs new UI board control and main board because it’s not reading the thermistors correctly as a result the unit is freezing up order parts. Need the unit defrosted; ordrng 1 W10822646 (U I BOARD ) and 1 W11172798 (MAIN BOARD )
Chase F.
RANGE - GAS JENN-AIR JGCP430WP "Upon arrival, removed and replaced the burner head. tested unit, operates good. Cx was worried about to spark coming from electrode. Instructed cx that unit is working perfectly normal and that spark is normal by design. Checked all other specs to make sure everything else is working good. Unit is working great, and by design,"
Chase F.
WASHER ROPER RTW4516FW1 Unit was stuck in pump out mode. Cleared out of pump out mode. Calibrated unit. Ran unit through automatic test cycle. Unit past all cycles with no problems. Unit is now working by design.
Cesar H.
WASHER WHIRLPOOL WTW7000DW3 Found gear case makes a squealing sound when spinning found this to be a dry seal on drive these seals arent to be lubricated after they are installed at the factory on the drives had to replace drive also wash plate was stuck to drive shaft, needed new one. Calibrated and tested unit after replacing drive and wash plate all tested good
Cesar H.
FREEZER WHIRLPOOL MTB1956GEW Replaced motor and harness all tested good
Cesar H.
RANGE WHIRLPOOL WFG361LVB2 Replaced failed parts unit tested good
Cesar H.
FREEZER WHIRLPOOL WRF535SMBM00 Found slider temp control for lower drawer was frozen causing cold air from freezer to constantly come in to the drawer cleared ice slider is now free so that temp can be controlled unit tested good
Cesar H.
WASHER GE GTW460ASJ6WW Replaced latch tested good
Billy J.
WASHER MAYTAG MVWB835DW3 Upon arrival cx stated unit giving of I put unit in diognosis and ran test one valve is froze removed and replaced retested job complete no leaks at this time
Cesar H.
REFRIGERATOR FRIGIDAIRE FFHB2740PPBA Found fill tube to ice maker frozen over last company that worked on unit left the seal around the opening of the fill tube causing fill tube to freeze over put new foam seal and cleared ice out of line all tested good
Billy J.
REFRIGERATOR WHIRLPOOL WRS325SDHZ02
Andrew P.
REFRIGERATOR JENN-AIR JFC2290VEP0
Aaron B.
WASHER MAYTAG MVWC300VW1 Unit agitator upper cam assembly has stripped, replaced the cam assembly tested operates ok now
Aaron B.
DISHWASHER KITCHENAID KDTM354DSS4 "Unit dispenser door gasket came off replaced, and tested operating ok at this time"
Aaron B.
DISHWASHER KITCHENAID KUDE20IXWH6 "Upper rack adjusters are broken needs new adjusters. Checked unit adjusters are covered parts and labor , replaced the adjuster reinstalled upper rack operations normal at this time"
Aaron B.
DISHWASHER KITCHENAID KDFE104HPS0 Upon arrival checked for any fault codes are any problems with the programming in the service mode unit is working as designed no codes found job complete.
William L.
REFRIGERATOR WHIRLPOOL WRF954CIHM00 "found ui panel connections fitting loose, ordered ui panel. for unit.; ordrng 1 W11330648 (ui panel)"
William L.
TRASH COMPATOR WHIRLPOOL GC900QPPB6 "Replaced switch assembly, ran cycle, tested ok, unit operating as designed."
William L.
DRYER MAYTAG MEDC300XW0 "replaced motor, found belt warn, installed dryer repair kit, ran dryer cycle, unit operating as designed; used 1 4392065 (DRYER REPAIR KIT) from stock"
William L.
MICROWAVE WHIRLPOOL WOC54EC0AS04 "F4E5, Replaced door latch assembly, ran short clean cycle, latch assembly locked & unlocked, unit operating as designed."
Timothy J.
RANGE JENN-AIR JGRP436WP01 Inspected unit and found the power inverter board is bad. Replaced and tested. Unit operating normally.
Timothy J.
RANGE JENN-AIR JDS1450DP0 Installed board. Tested unit. Unit checks ok.
Timothy J.
DISHWASHER FRIGIDAIRE FFBD2406NB
Timothy J.
REFRIGERATOR MAYTAG MSS26C6MFZ00 Instructed customer to make a video of the sound so I could determine the source from that if needed.currently the unit is operating as designed.
Timothy J.
REFIRGERATOR JENN-AIR JS42SSDUDE01 Installed doorskins. Unit operating as designed.
Timothy J.
REFRIGERATOR WHIRLPOOL WRF767SDHV00 Installed IM and fan assembly. Ran tests on installed parts. IM harvested and filled correctly in the test . No leaks noted.
Steven W.
WASHER WHIRLPOOL WFW75HEFW0 Ran diagnostics. Had f5e3 error code. Found door lock binding. Needs door lock. EST 307.00. Send invoice to Email.; ordrng 1 WPW10443885 (door lock)
Timothy J.
REFRIGERATOR JENN-AIR JS48PPDUDE01 Unit has frost on the upper wall of the freezer and top of the door. Steamed gasket and checked for a good seal. Unit sealing. Customer to monitor unit and report if needed.
Timothy J.
DRYER WHIRLPOOL WED4815EW1 Inspected unit. Found components check ok. Reconnected the unit to the ducting(only about a foot long) and found the vent was restricted. I checked that first and the vent appeared ok. When the dryer is installed the ducting shifts and causes the restriction. Either something outside was causing the flap not to open correctly or the exhaust fixture is faulty. Informed customer about how to resolve this issue. Unit checks ok at this time.
Steven W.
REFRIGERATOR WHIRLPOOL WRS325SDHZ00
Steven W.
WASHER WHIRLPOOL WFW9250WW00 "Replaced LF shock, strike. Tested spin cycle. Found worn tub bearings. Unit fills, washes, drains properly.."
Steven W.
REFRIGERATOR JENN-AIR JFFCC72EFP00 UI not received. UI sent to customer is same wrong part as previous replacement part Replaced HV control. Unit is cooling properly at this time.
Steven W.
WASH/DRY COMBO WHIRPOOL WET4027HW0 "Replaced upper wiring harness. Ran diagnostics. No error codes found. Tested several times. Fills, agitates, drains, rinses, & spins properly at this time. Complete."
Steven W.
DRYER - GAS WHIRLPOOL LGQ8858HQ0 "Found support roller seized up, weak motor start windings.; ordrng 1 279827 (motor dryer) and 1 4392065 (dryer repair kit)"
Steven W.
RANGE WHIRLPOOL WFG515S0ES1 "Replaced screws, trims on oven door. Oven door is opening/ closing properly. Range is working properly at this time. Complete."
Steven W.
REFRIGERATOR WHIRLPOOL WRF560SEYM05 Replaced UI, thermistor kit, & evaporator fan blade. Unit is cooling properly at this time. Found RC door bottom hinge area broken at hinge bore. Needs right RC door, nameplate .; rqstng P&A on 1 LW10413519 (dor-fip ms) and 1 WPW10481433 (nameplate)"
Steven W.
WASHER WHIRLPOOL WTW7040DW0 "Ran diagnostics. Had f0e5, f0e3, & f2e1. Cleared error codes. Found suspension rod LR socket came off tub. Reinstalled suspension rod.Tested mixed, drain & spin with load. Fills, agitates, drains, rinses, & spins properly. Complete."
Steven W.
REFRIGERATOR KITCHENAID KBSD608ESS00
Rod H.
REFRIGERATOR WHIRLPOOL WRV986FDEM01
Steven W.
COOKTOP KITCHENAID KECC604BSS00 Replaced LF & RF elements. All burners are working properly at this time. Complete.
Steven W.
WASHER MAYTAG MVWX655DW1 Ran diagnostics. No error codes. Tested washer several times. No leaks found from washer. Possible drainpipe backing up. Advised customer to call plumber. Complete.
Rod H.
WASHER MAYTAG MVWC200BW0 "Stops mid cycle then drainsSERVICE CONTRACTFound drain hose looped at bottom of machine. Found no malfunction codes stored in memory.All components check out during self diag sequence.No leaks. Recalibrated product Ran test cycle after removing and reinstalling electrical connections at board and under console switches, with no Adverse events.All seems operating as designed."
Rod H.
REFRIGERATOR WHIRLPOOL WRT134TFDW00
Rod H.
WASHER MAYTAG MHW5500FW1 Return with ordered part and installed.As designed operation and condition returned with no leaks.
Rod H.
WASHER WHIRLPOOL WTW4816FW Continually makes noise and lights won’t light up does it own thing without user interaction.Confirmed Over suds sensed by control self suds expulsion taking place. Found drain hose kinked and anti-kink cord plugging sensing tube on control. Removed per factory directive.
Rod H.
WASHER MAYTAG MVWC200BW0 Consumer experiencing shimmy and shaking of product when in spinConfirmed Unbalanced load in product upon arrival. Store malfunction code stored in memory indicated an unbalanced load as well. Further found footing of product as such that excessive shaking and vibration would also cause shimmy and shake. Leveled machine and as designed
Rod H.
WASHER WHIRLPOOL WTW5000DW0 Intermittently Stops when spin cycle increment is reached. Confirmed Board shuts down during wash and has to be restarted.Replaced machine control calibrated and as designed operation and condition seemed to have returned.
Rod H.
REFRIGERATOR WHIRLPOOL WSF26C3EXW01 Icemaker was ordered on last visit but was not on this order had to pre-idand order again Replaced ice maker. Realigned door. Was causing air lk into ffd compartment.; pckd up 1 WPW10251076 (icemaker)
Rod H.
WASHER WHIRLPOOL WTW8500DC2 Won’t drainConfirmed Pump impeller broken.Replaced pump and calibrated machine. No listenAs designed operation has now returned; pckd up 1 W10876600 (drain pump)
Raymond H.
DRYER MAYTAG MGDB855DC4 While attempting to assemble unit after breakdown tech noticed bulkhead surface from the 10-3 o’clock position is non existent. Tech missed this first time. Needs bulkhead and drum; ordrng 1 W10861007 (bulkhead)
Raymond H.
REFRIGERATOR WHIRLPOOL KRFC704FSS00 Replaced controls valve and housing. Wrong cover sent. Needs evap cover.; ordrng 1 W11167902 (COVER)
Raymond H.
REFRIGERATOR WHIRLPOOL WRS315SDHZ02 "Replaced control box, thermistor and diffuser. Tested unit. Unit functions as designed."
Raymond H.
M/W OTR WHIRLPOOL WMH31017FW0 "Replaced transformer, capacitor and fuse. Tested unit. Unit still just buzzing
Raymond H.
M/W OTR WHIRLPOOL WMH31017FW0 "Replaced transformer, capacitor and fuse. Tested unit. Unit still just buzzing.
Raymond H.
WASHER MAYTAG MVWB765FW0 Replaced control and console. Tested unit. Unit functions as designed.
Raymond H.
WASHER MAYTAG MHW3505FW1 Upon arrival unit had same long drain code. Unit is stacked and difficult to move. Need second man.; ordrng 1 WPW10443885 (door lock) and 1 WPW10605427 (pump-water)
Raymond H.
REFRIGERATOR WHIRLPOOL KRMF706ESS01 Upon arrival shelves not sitting proper in RC. Shelves can’t toward center of unit and will not allow for shelving to sit on same rung. Need to call tech line.
Raymond H.
MICROWAVE KITCHENAID KEMC307KSS05 Finished repair. Tested unit. Unit functions as designed
Raymond H.
REFIRGERATOR MAYTAG MFI2568AES "Upon arrival unit display flashing and dispenser motor opening and closing. Found SP for this, need to replace control.; rqstng P&A on 1 W10890094 (cntrl-elec)"
Randy C.
COOKTOP JENN-AIR JGC3536GS Removed and replaced cooktop. Replaced knobs found knobs defective found chipped at each knob no knob was safe. Reordering.; ordrng 5 W11045335 (knob)s
Raymond H.
REFRIGERATOR WHIRLPOOL WRT111SFDW04 Replaced compressor. Unit passed vacuum test. Recharged with 3.0oz of r134a. Tested unit. Unit has proper heat exchange. Unit is cooling.
Raymond H.
REFIRGERATOR JENN-AIR JFC2290VEP8 "Upon arrival ice maker not making ice. Tested and found ice maker not cycling. Quoted cx for repair, cx approved. Replaced ice maker and tested, unit functions as designed.
Randy C.
WASHER WHIRLPOOL WFC7500VW2 Found not completing cycle. Ran test found bad latch and drain pump not draining. Ordering parts; ordrng 1 W10193047 (trap) and 1 WPW10192994 (switch) and 1 WPW10465252 (pump-water)
Randy C.
WASHER MAYTAG MHW3505FW1
Randy C.
REFRIGERATOR WHIRLPOOL WRT106TFDW01 Found not cooling. Set to cool and vacuumed system. Refilled with 4.27 oz of refrigerant. Instructed cx to wait 24 hours for optimized cool.
Randy C.
RANGE WHIRLPOOL UXT4030ADS2 Removed and replaced unit now working as designed
Randy C.
DISHWASHER AMANA ADB1400AGW1 Not drying. Found passed diagnostics. No error codes. Found unit working as deisgend no rinse aid in the unit advised Client that rinse aid improves drying client doesn’t understand how the rinse aid could affect unit. Gave instructions. reffering to manufacturer. Job complete.
Randy C.
DISHWASHER JENN-AIR JDB9200CWP2 Found unit not powering up. Bad control board gets power but won’t power up REMVED and replaced parts now working job complete
Patrick C.
WASHER WHIRLPOOL WFW7590FW0 Found the unit having issues with a noise. I spun basket by hand and it made a real loud grind noise. Thought it was bearing. But some how a factory screw got between rotor and stator. When removing the screw had broke motor winding. Needs new stat for and rotor ; ordrng 1 W10870752 (stator) and 1 WPW10453673 (rotor)
Randy C.
DISHWASHER KITCHENAID KUDS30IXSS7 Found control not responding to commands. Found bad control. Removed and replaced now working as designed.
Randy C.
WASHER WHIRLPOOL model Client refused service at the door. Said that she called about a month ago does not need service.
Patrick C.
REFRIGERATOR WHIRLPOOL WRX986SIHV00 Removed and replaced board and ice maker. Tested unit. All ops checked good
Patrick C.
WASHER MAYTAG MVWX655DW1
Patrick C.
WASHER WHIRLPOOL WTW7040DW Found customer having issues with f1 errors. Checked out and unit intermittently works. Shuts off mid cycle and won’t complete. Control failure. Removed and replaced. Calibrated and ran auto test. All ops checked good
Patrick C.
REFRIGERATOR WHIRLPOOL WRF989SDAF01 Removed and replaced controls. Compressor and evap. Vacuumed and recharged with 5.5 of r134. Tested unit. All ops checked good. ; used 1 CD8404 () from stock
Michael M.
DRYER MAYTAG MGDX655DW2 Removed and replaced faulty gas coil. Retested unit and still no ignition.Removed all parts. Had to leave VET hospital and find a mechanic shop to use bench vise to transfer gas tube on regulator block. Reinstalled all parts and retested. Still no ignition. Sensor glows hot and then turns off no flame.Ordering harness and radiant sensor WP338906Harness is PSP so tech will come back and install sensor and see how it goesReturn 3/21/19 8-12 requested; ordrng 1 WP338906 (sensor)
Kevin M.
MICROWAVE KITCHENAID KMBS104ESS02 Unit is not heating. I found that upper left door switch not making contact unless you shut door with excessive force. Unit needs door switches and inner locks. Ordering switches and harness to get inner locks. Will need to pull unit out of wall on return. Allow 1 hr on return. ; ordrng 4 W10211972 (switch)s and 1 W10874025 (harns-wire)
Mike K.
REFIRGERATOR WHIRLPOOL WRS325SDHZ02 reolaced thermister and diffuser tested
Michael M.
WASHER MAYTAG MVWC416FW1 Cx states inner parts of tub are loose. Tech found agitator loose and cap removed from top of agitator. Used extension and tightened agitator assembly and installed fabric softener cap. Unit spin with no noises. Unit currently not installed in home.Job complete
Kevin M.
WASHER WHIRLPOOL MVWB765FW2
Kevin M.
WASHER WHIRLPOOL WFW92HEFC0 "I found that the hose that goes from dispenser to the door boot had come off due to rubber on door boot being stretched out over time. Also found dispenser starting to put water in load and go cartridge. Need to replace door boot, dispenser housing and fill valve. Removed and replaced door boot, dispenser, and fill valve. Tested unit. All tests good."
Kevin M.
REFRIGERATOR WHIRLPOOL WRF993FIFM00 "Took pic of pop. Unit not cooling, found frozen over RC evaporator. Unit has old software version and old style evap cover. Unit needs new evap cover and board per service pointer. Removed and replaced evap cover and main control. Tested unit. All tests good."
Kevin M.
WASHER MAYTAG MVWB765FW1 Control panel is shorted out and not allowing any selection. Unit needs main control and user interface due to short in panel. Ordering parts. ; ordrng 1 W11135391 (CONSOLE) and 1 W11135392 (CNTRL-ELEC)
Kevin M.
M/W OTR KITCHENAID KHMC1857BSS1
Kenneth M.
WASHER MAYTAG MHW5500FW1
Kevin M.
REFRIGERATOR WHIRLPOOL WRS588FIHV00 "Took pic of pop. Customer concerned with noise from RC and door not closing properly. I found that the RC door was not closing properly and had to adjust closers to correct door closing. Noise is coming from damper, informed customer on normal damper sounds. All tests good."
Kevin M.
WASHER MAYTAG MVWC565FW1 Unit is dead with no operation. I removed panel and found main control has proper voltage but not lighting up. Failed main control. Removed and replaced main control. Tested unit. All tests good.
Kenneth M.
REFRIGERATOR KITCHENAID KRMF706EBS01
Kenneth M.
REFRIGERATOR WHIRLPOOL WRB322DMBB00 Installed ice maker and tested unit. Unit is now working properly. Customer approves function at this time.
Kenneth M.
RANGE GE JGSS66SEL1SS Shaft on gas valve loose. Ordering new gas valve. Did not reschedule ; ordrng 1 WB21X20470 (valve burner 270)
Kenneth M.
DISHWASHER KITCHENAID KDTM354DSS3 Installed sump assem and tested unit. Unit is now working properly. Customer approves function at this time. No leaks found.
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFHB2740PP9a Installed new air handler gasket kit and fan. Tested unit. Unit is now working properly. Customer approves function-at this time.
Kenneth M.
MICROWAVE OVEN FRIGIDAIRE FFMV1645TS Found peeling inside door and scratched handle. Unit is now working properly. Customer approves function at ths time.
Kenneth M.
OVEN WHIRLPOOL WFG320M0BW2 Found unit smell in like gas and not igniting oven properly. Replaced oven igniter. Was only pulling 2.7 amps. Should pull 3.2. Installed sensor. Tested unit. Unit is now working properly. Customer approves function at this time.
Kenneth M.
LAUNDRY WHIRLPOOL WED5000DW2 Found unit not drying. Customer had dryer vent smashed causing unit to blow thermal cutoff. Reset 5ermal cutoff fixed vent so it was no longer smashed and tested unit. Unit is now working properly. Tested venting with vent tester. Unit checked good. Customer approves functions.
Kenneth M.
WASHER MAYTAG MVWB965HW0 Instructed customer on proper use and care. Loading techniques and soap usage. Customer approves function at this time.
Kenneth M.
WASHER WHIRLPOOL WFW75HEFW0
Kenneth M.
REFRIGERATOR FRIGIDAIRE FGTR2037TF Installed evap motor and tested unit. Unit is now working properly. Customer approves function at this time.
Kenneth M.
WASHER MAYTAG MVWC465HW0 "Installed control,board and tested unit. Unit is now working properly. Customer approves function at this time."
Kenneth M.
DRYER WHIRLPOOL WED5000DW2 Found unit making noise due to a piece of magazine stuck in blower wheel. Removed magazine page and tested unit. Unit is now working properly. Found issue wit electrical lug or socket.
Kenneth M.
REFRIGERATOR WHIRLPOOL WRS315SNHM01 "Installed compressor and vacuum system down for 10 minutes. Unit held vacuum. Charged system with 5.3 OZ of R134A refrigerant and tested unit. Unit is now working properly. Customer approves function at this time. Pressures checked good. No leaks found. ; used 1 CD8404 (), and 5 R134a (REFRIGERANT) from stock"
Kenneth M.
WASHER WHIRLPOOL WTW4816FW2 Found unit with a broken agitator. Screws keeps backing out; ordrng 1 W10772621 (screw) and 1 WP3951744 (agitator)
Kenneth M.
WASHER WHIRLPOOL WTW4955HW0 Found unit squeaking due to oil on belt and pulley. Replaced gearcase with Pre-ID and tested unit. Unit is now working properly. Cleaned off as much oil as possible. Customer approves function at this time.
Kenneth M.
REFRIGERATOR WHIRLPOOL WRX735SDBM02 Installed ice container and ICEMAKER. Tested unit. Unit is now working properly. Customer apppres function at this time.
Jim S.
OVEN KITCHENAID KOCE500ESS06 noisy stirrer fan motor; ordrng 1 W10838964 (motor-fan) and 1 W10861504 (blower) and 1 W10911403 (motor-turn)
Kenneth M.
OVEN WHIRLPOOL WOS51EC0HS01 Installed console and tested unit. Unit is now working properly. Customer approve funcction at this time.
Kenneth M.
WASHER MAYTAG MHW5500FW1 Installed control panel and tested unit. Unit is now working properly. Customer approve function at this time.
Jim S.
FREEZER GE TFX27PFXDAA Cleared defrost drain tube. Removed ice. Unit tested ok
Jim S.
REFIRGERATOR WHIRLPOOL ED2FHGXSQ00 Broken switch holder; ordrng 1 WP2180226 (bracket)
Jim S.
REFRIG/SIDE-BY-S WHIRLPOOL WRS325FDAW04 Replaced ice bucket and dispenser board
Jim S.
REFRIGERATOR WHIRLPOOL WRF989SDAM00 Tape came to us damagedTech line is recomending the epoxy7724400353; ordrng 1 8201700 (repair kit)
Jim S.
DRYER MAYTAG MGD5100DW1 Replaced door with hinges and gasket. Unit tested fine
Jim S.
WASHER WHIRLPOOL WTW5000DW0 Replaced wire harness. Calibrated unit. All test are hunky dory.
Jim S.
REFRIGERATOR KITCHENAID KFXS25RYMS4 Installed new defrost drain tube; used 1 W10619951 (TUBE DRAIN) from stock
Jim S.
ICE MACHINE KITCHEN AID KUIC15PHZS0 Replaced the parts on the previous work order. Unit tested OK
Jim S.
DOUBLE WALL OVEN KITCHEN AID KODT100ESS01 #5889F1E0 and F1E1 are the two stored fault codes. Bad user interface and bad appliance manager board; rqstng P&A on 1 W10777215 (cntrl-elec) and 1 W10890580 (swtch-memb)
Jim S.
REFRIGERATOR WHIRLPOOL WRF736SDAM14 Replaced freezer evaporator fan motor. Unit tested ok
Jim S.
REFRIGERATOR KITCHEN AID KSRU25FKBT03 Replaced cold control. Unit tested OK
Jim S.
WASHER MAYTAG MHW8200FCO F1E1. F3E1Replaced main control board. Unit tested ok
Jesus C.
REFRIGERATOR WHIRLPOOL KRFF305ESS00 Customer states that unit is not cooling. Checked unit and pulled unit out. Removed compartment cover and found the compressor very hot. This unit need a complete seal system.; ordrng 1 W10507884 (compressor) and 1 W11256565 (EVAPORATOR) and 1 WPW10143759 (dryer) and 1 WPW10233569 (tube)
Jim S.
REFRIGERATOR GE FFHT2032TP2 Per service tips I used silicone in the gaps between the liner and the cabinet to reduce air flow into the refrigerator
Jesus C.
RANGE WHIRLPOOL WEG515S0FS0 Pulled unit out about 6 inches and disconnected power. Removed screws to panel cover and removed UI panel. Removed harness and installed new harness. Assembled unit and plugged unit back in and in place. Tested unit and all ignitors and burners are working. Unit is now working as design.
Jesus C.
DRYER WHIRLPOOL CGM2745FQ0 Customer states that dryer is taking to long to dry. Checked unit and ran tests. All test performed when diagnosing unit passed. Called commercial line and document. Unit is now working as designed
Jesus C.
REFRIGERATOR WHIRLPOOL WRS588FIHZ00 Removed diffuser and installed new. Ran test and diffuser is working properly. Advised customer to change temperatures on panel accordingly. Unit is working as design.
Jesus C.
WASHER MAYTAG MVWB835DW4 "Customer states that unit is not filling with water. Ran test and found several error codes. Turned off unit, water valves and disconnected hoses. Removed UI panel and valve. Installed new valve and assembled unit. Ran manual and auto test. Unit is now working as design.F2-E1. Stuck buttonF8-E1. Long fill"
Jesus C.
DISHWASHER WHIRLPOOL KUDD03STSS2
Jesus C.
DISHWASHER KITCHENAID KDTE234GPS0 Removed front panel and replace door latches and strike. Adjusted unit feet and tested. Unit is now working as design.
Jesus C.
WASHER WHIRLPOOL CAE2745FQ0 Customer states that unit is leaking water. Checked unit has diagnostics and no error codes found. Ran cycle and didn’t find unit leaking. Unit is working as design.
Jesus C.
WASHER WHIRLPOOL WFW75HEFW0 Customer states that unit is leaking. Checked unit and found the bellows with a small hole. Ran diagnostics and found several error codes. Unplugged unit and removed retainer. Removed bellow and installed new. Assembled unit and tested. Unit is now working as design.F5-E2 Door lock errorF0-E1 Load detected during cleaning washer cycle
Jesus C.
FREEZER WHIRLPOOL ESU15C Customer states that unit is making noise. Checked unit and found the compressor making noise. Gave customer quote and denied repair. Customer paid for call $115.00 per credit card.
Jesus C.
DISHWASHER KITCHENAID KDTM804EBS2 Customer states that unit is leaving condensation in tub. Ran diagnostics and no error codes found. Advised customer of using rinse aid and finish pods. Customer is currently using cascade with dawn and I explain that this specific soap creates to many suds. Unit is working as design.
Jesus C.
DRYER MAYTAG MGDB765FW0 Customer states that unit is taking to long to dry clothes. Ran unit and no error codes found. Place my test kit on filter section and unit failed. There is an airflow restriction. Pulled unit out and removed vent from unit. Reran Test and passed. Customer needs vent cleaned from wall out. Placed unit back in place. Unit is now working as design.
James M.
DISHWASHER WHIRLPOOL WDT730PAHZ0 "F4e3, f5e1. Put unit into test mode. Unit intermittent door issues Unit filled but motor not engaging. Bother errors have control in common. Ordering new control and sump assembly. Will return 3-19 to install. ; ordrng 1 W11085683 (pump&motor) and 1 W11085683 (pump&motor) and 1 W11305308 (CNTRL ELECT )"
Jesus C.
M/W OTR JENN-AIR JMV8208CS1 Customer states that unit has door error code. Removed power and removed vent and panel. Removed interlocks and installed new. Assembled unit and rested. Unit is now working as design.
Jesus C.
REFIRGERATOR WHIRLPOOL WRS571CIHZ01 Customer state that unit dispenser amount not working. Calibrated water dispenser and tested. Placed cup and ran 1 cup on water on dispenser. Unit is working as design.
Jesus C.
DISHWASHER KITCHENAID KDTE304GPS0 Customer states that unit is not cleaning dishes properly. Ran test and no error codes found. Customer is not using recommended soap leaving soap residue. Unit is working as design.
James M.
FREEZER JENN-AIR JFC2089WEM9 Unit has ice buildup in drain. Pan and bad frost pattern on evap signifies low charge or obstruction. Cleared drain. Ordering new compressor and dryer. Requesting sealed system tech for repairs. ; ordrng 1 W10507884 (compressor)
James M.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 Found unit with minor gapping on fridge left door gasket. Heated gasket and reformed seal. Also found control noisy. Replaced evap motor and control. Unit now not making noises and sealing correctly. Job complete.
James M.
REFRIGERATOR WHIRLPOOL WRF989SDAW02 "Found unit with no cool. Ordering new compressor and dye drier. Needs sealed system tech for installation. ; ordrng 1 W10276644 (compressor), 367.79"
James M.
MICROWAVE KITCHENAID KMBS104ESS02 Replaced cover. Unit works no as intended and customer approves.
James G.
REFRIGERATOR WHIRLPOOL WRF989SDAH00 "Deli board bad, unplugged for now; ordrng 1 WPW10565996 (cntrl-elec)"
James M.
DRYER WHIRLPOOL WGD7500GC0 Installed parts and lugged unit into extension coats to test ignitor. Glow bar working as intended. Job complete.
James G.
MICROWAVE GE PEB2060SM2SS Bad mag tube APPROVED APPROVED ; ordrng 1 WB27X26081 (magnetron)
James M.
DISHWASHER FRIGIDAIRE FGID2466QF Customer stated that service had already been done by another company. Service no longer needed.
James G.
REFRIGERATOR KITCHENAID KRFF305ESS00 Tightened freezer door handle and removed door mullion and reinstalled.Tested ok
James G.
REFIRGERATOR JENN-AIR JS48PPDUDE01 Replaced defective part listed Tested ok
James G.
REFRIGERATOR WHIRLPOOL KRSC503ESS01 Replaced listed part Tested ok
James G.
MICROWAVE KITCHENAID KMBS104ESS02 Line fuse not secured into holderSecured and tested ok
James G.
DISHWASHER BOSCH SHX68T55UC/02 "Replaced listed part, customer says unit not draining, filled and drained unit multiple times with no failure."
James G.
WASHER WHIRLPOOL WTW5000DW2 Replaced listed part Tested ok
James G.
MICROWAVE GE PEB2060SM2SS Bad mag tube APPROVED APPROVED ; ordrng 1 WB27X26081 (magnetron)
James G.
RANGE WHIRLPOOL WFG320M0BW2 Replaced listed parts due to multiple discoloring issues Tested ok