"Ran diagnostics. Had f5e1, f2e1 error codes. Found lid lock failing. Replaced latch assembly. Ran load size calibration, auto test cycle. Locks/unlocks,fills , agitates, drains, rinses, dispenses, and spins properly at this time. Instructed customer on normal water levels. Unit is working properly as designed. Complete.; used 1 W10810403 (Latch) from stock"

Replaced defective motor and harness.

Customer stated that the unit is making a grinding sound. I found some wear marks on slider. Removed and replaced slider assy. Tested unit. All tests good.

"Replaced latch Assy, ran self diagnostic cycle, unit operating as designed. Cx refused to sign off on job."

Installed new icemaker. Cycled icemaker. All ops now checking normal.

After replacing the faulty heating element the front left burner is now operating. Job completed. All functions tested properly.

Found micro hood exexively loud and not heating found flap on backwards reposition replaced magnetron test ok complete no dents or dings cause by tech paid in full with credit card.

Arrived with parts . Installed new panel. Rechecked ops. Unit ran as designed.

"JB out 3/23/22 upon arrival verified loud noise from freezer Fan fan scrapping ice and frost. Inspected FC drawer and verified it closes and seals but cabinet was not leveled properly when installed. Amount of frost indicates drawer has been left afar causing heavy frost buildup. Customer states frost has been present for one month. See quick pic photo showing some packages not cover in frost as drawer was closed and sealed properly. Some item in FC heavily frosted indicating items stored in FC during a period of time when the drawer was not closed or sealing completely . Advised customer to remove all perishable foods and place in a different refrigerator, unplug this unit and allow to defrost with all doors opened for 24-36 hours. After all water from melted ice and frost is wiped up the unit can be plugged in and allowed to run for 8-10 hours before returning perishable foods to be stored. Instructed customer to remove toe panel grille EVERY 2 MONTHS for the life of the refrigerator and clean condenser coils to restore low electrical operating costs, reduce over run time and increase life of the product. NOTE: Blocked condenser coils may cause premature compressor failure and may or may not be covered by extended warranty plan contract. No parts used. No charge to customer today. JOB COMPLETE"

JB Out 3/23/22. Installed replacement water (Drain) pump w11458345 as ordered. Reassembled and tested operation with customer. Verified proper water pump output flow is now functioning as designed. Sent ACU back (not needed). No charge to customer. Job Complete

"Customer concerns, washer not advancing wash cycles. In diagnostics found, shifter fault. Installed new shifter ( truck stock ), performed calibration. All functions worked as designed, no leaks.; used 1 W11481722 ( Actuator) from stock"

"Pulled unit from wall. Disassembled unit, and replaced the control. Board was in the control Box. Installed both components. Installed microwave. Test passed. All ops normal. Unit starts when start button pushed."

"JB out 3/23/22. Installed replacement Lower harness. Reassembled unit and tested fill, wash drain and spin functions. Unit now operates as designed. No charge to customer. JOB COMPLETE"

Cycled power and cleared board.Tested ok

Installed part tested check out ok complete no dents or dings cause by tech.

"Removed and replaced door, asked cx to monitor and report any issues."

Customer stated that are getting condensation inside the freezer that is freezing. I found a freezer door sitting too low not sealing correctly. Also found door seal is not ceiling heat treated door seal move door up tested all works good this time

install part tested unit all ops normal

"Unit was going straight into drain mode, unable to stop this. Attempted releasing pressure hose and control stop for a second and continued to drain. Removed and replaced control it solved issue. Provided Estimate cx approved. Calibrated and tested ops unit now working as designed Sr#7733256242"

Replaced defective coin drop.Tested ok

Installed new part. All ops now checking okay.

Unit had start device incorrectly on compressor causing it to not start replaced capacitor and unit is backmopestional

Installed parts and ran cycle. Unit passed all tests and is operating as designed.

"Replaced ui panel, checked oven sensors, found 3 inch long sensors, tested oven functions, rechecked for codes, unit operating as designed"

"Replaced compressor , filter dryer, installed service port, swept system with nitrogen, pressure tested system with nitrogen, found no pressure drop for 15 min. recharge system, unit cooling at this time, sealed system warranty job.; used 1 W10913906 (Access port) from stock"

"Fixed- installed new parts (capacitor, mag, diode) tested unit is now heating as designed- cx ok repair."

Ran unit in diagnostic and unit passed al tests at time of service. F0E2 suds. Customer has been washing her clothes on bulky setting all loads on bulky. Explained to her shes been using wrong cycle for her loads. Unit is agitating as intended. Job complete.

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

Installed new diffuser. All ops now checking out normal. Job complete.

Picked up old unit to haul back to the shop and dropped off check

"Replaced actuator with original part, ran self disgnostic cycle, unit operating as designed"

Found unit with Key stuck under washplate causing rubbing noises. Removed and tested unit. Unit functions as intended. No error codes.

"Fixed-installed new parts (filter, housing) flush system- set temps- cooling, light, fans, are all working as designed- cx ok repair."

Removed and installed new seal. Unit working as intended.

Installed new parts. All ops now checking out normal.

"Customer canceled, Customer thought they had a 10 year warranty"

Ibstalled control and UI. Tested. Unit is working properly. Custom3r approves function at this time.

Replaced failed parts tested unit all tested good

Replaced parts and ran cycle. Unit passed all tests and leak is no longer present.

Replaced door and vent all tested good

"Upon arrival, reset power to board and checked all settings. Cycles ice maker and checked to make sure water dispensing properly . Unit ran as designed."

Replaced listed parts. Unit is back operational. Job complete.

"On arrival I found broken middle arm assembly, i installed and secured new middle arm assembly and spray arm, tested unit, unit is now operating properly as designed at this time of service"

Installed new user interface and unit works per design

Replaced defective motor and harness.

Found refrigerator freezer reading 29 degrees not building a full frost pattern per Frigidaire if unit needs a seal system customer to call customer care for further info complete no dents or dings cause bytech.

"Customer concern was no ice, unit had ice box fan frozen over due to freezer door gasket being ripped and leaking air. Thawed out and customer did not want to replace gasket. Unit is back operational."

Installed new icemaker. Cycled icemaker. All ops now checking normal.

"First manifold showed up as a console for a front load washer, second one was correct. Installed and tested all ok."

"Found tripped back interlock causing door not to close, tripped interlock back collected 125"

Installed new parts and re-tested unit all test pass at time of service. Job completed

Removed and replaced coils and drum. Tested unit. All tests good.

"JB out 3/23/22 customer states a flashing light sequence of 8 and 4 was observed. Customer then corrected a small water drip at the water inlet connection prior to my service visit of 3/23/22. Ran diagnostics and verified only F8E4 indicating overflow/Float switch open. Cleared stored code. Removed toe panel Advise water being supplied to dishwasher is far below the required 120f minimum as outlined in the supplied installation instructions. Suggest the purchase, installation and use of a Point of Use Hot water heater mounted under the kitchen sink and run ONLY to the two dishwashers (set to 125f) to insure no less than 120 f water temperature is supplied to the dishwasher(s) the moment that the start button is pressed to insure proper cleaning performance. No parts used. No charge to customer. JOB COMPLETE"

JB Out 3/23/22. Installed replacement water (Drain) pump w11458345 as ordered. Reassembled and tested operation with customer. Verified proper water pump output flow is now functioning as designed. Sent ACU back (not needed). No charge to customer. Job Complete

Installed new parts and re-tested unit all test pass at time of service. Job completed

Ran a check on unit. Heat is there. Checked vent.vent was blocked. Check and cleaned out. Clothes should dry a lot better. Checked for codes and unit didnt have any. Ran another cycle and unit seems to be working a lot better. Job completed

"Removed unit from cabinet. Removed all racks and tubing from inside the unit. Replaced sump assembly and hose . Reassembled unit and tested. Unit checks ok, no leaks noted. Reinstalled unit into cabinet."

"IL recall Checked the unit noticed the dampener door not opening , Fresh food section was 54° freezer section was -13° at this time unplug the unit replace the fresh food thermistor check the connection at the Dampener everything look good , replaced The fresh food thermistor turned on the unit the dampener opened ,noticed the air flow was not ideal opened the freezer door and air rushed in good , the return vents are clogged , customer is going to defrost the unit three full days to make sure theres no air blockage in the return vent unit should work correctly after that"

Installed part tested check out ok complete no dents or dings cause by tech.

"Found the unit, not cooling, verify problem compressor not running, replace compressor,service valve and drier, charge refrigerant 68g R600a check compressor condenser and refrigerator fan motors running normal"

"Checked operations, unit was working correctly no problems that I could find at this time customer was using the washer correctly as far as I can see no mechanical failures found with this unit at all at this time"

"Didnt have valve ending in 41320. Reordered parts. Called office and left them know. Removed power installed all parts. Assembled unit, test for ops. Unit is dispensing water. All ops normal."

Customer stated that the unit is making a grinding sound. I found some wear marks on slider. Removed and replaced slider assy. Tested unit. All tests good.

After replacing the faulty heating element the front left burner is now operating. Job completed. All functions tested properly.

Arrived with parts . Installed new panel. Rechecked ops. Unit ran as designed.

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

Installed part tested check out ok complete no dents or dings cause by tech.

"Pulled unit from wall. Disassembled unit, and replaced the control. Board was in the control Box. Installed both components. Installed microwave. Test passed. All ops normal. Unit starts when start button pushed."

Found no error codes stored at this time. Ran through diagnostic and spin hesitated to ramp up. I recalibrated the control and now the unit is spinning properly. Job completed.

"Fixed-installed new parts (filter, housing) flush system- set temps- cooling, light, fans, are all working as designed- cx ok repair."

Found after replacing the suspension the shock test passed. All functions tested properly after repair. Job completed

Ibstalled control and UI. Tested. Unit is working properly. Custom3r approves function at this time.

"Removed and replaced door, asked cx to monitor and report any issues."

Replaced parts and ran cycle. Unit passed all tests and leak is no longer present.

install part tested unit all ops normal

Replaced defective coin drop.Tested ok

"Replaced defective valve, tested unit and is working properly"

Installed new user interface and unit works per design

Installed parts and ran cycle. Unit passed all tests and is operating as designed.

Installed new compressor and recharged unit. No noise on start up . Unit back operational .

"Replaced compressor , filter dryer, installed service port, swept system with nitrogen, pressure tested system with nitrogen, found no pressure drop for 15 min. recharge system, unit cooling at this time, sealed system warranty job.; used 1 W10913906 (Access port) from stock"

Installed new parts and re-tested unit all test pass at time of service. Job completed

Installed new diffuser. All ops now checking out normal. Job complete.

Customer stated that the strike is broken removed and replaced strike tested all works good at this time.

Removed and installed new seal. Unit working as intended.

Installed new pump. All functions now checking out normal.

"IL recall Checked the unit noticed the dampener door not opening , Fresh food section was 54° freezer section was -13° at this time unplug the unit replace the fresh food thermistor check the connection at the Dampener everything look good , replaced The fresh food thermistor turned on the unit the dampener opened ,noticed the air flow was not ideal opened the freezer door and air rushed in good , the return vents are clogged , customer is going to defrost the unit three full days to make sure theres no air blockage in the return vent unit should work correctly after that"

"Checked operations, unit was working correctly no problems that I could find at this time customer was using the washer correctly as far as I can see no mechanical failures found with this unit at all at this time"

Replaced listed parts. Unit is back operational. Job complete.

Replaced defective motor and harness.

"Removed and replaced sensor, main control and door gasket. Tested unit. All tests good."

Installed new icemaker. Cycled icemaker. All ops now checking normal.

Replaced valve and ice maker. Unit now working as intended.

Customer stated that the light in the microwave is out and console not working. Removed and replaced console bulb and control. Tested all works good at this time.

JB Out 3/23/22. Installed replacement water (Drain) pump w11458345 as ordered. Reassembled and tested operation with customer. Verified proper water pump output flow is now functioning as designed. Sent ACU back (not needed). No charge to customer. Job Complete

Installed new led and units lights are all working. Job complete

Installed part tested check out ok complete no dents or dings cause by tech.

Installed new led and units lights are all working. Job complete

Found no error codes stored at this time. Ran through diagnostic and spin hesitated to ramp up. I recalibrated the control and now the unit is spinning properly. Job completed.

Found after replacing the suspension the shock test passed. All functions tested properly after repair. Job completed