Local Reviews
Powered by Fluid LOCAL
Rich S.
ICEMAKER KITCHENAID KUID508ESS1 Ran diagnostics passed. Cleared obstruction from drain Assam. Operating as designed.
Rich S.
RANGE - ELECTRIC KITCHEN AID KSGG700ESS1 "Replaced key pad F2E1 code. . Ran diagnostics, passed. Operating as designed."
Rich S.
DISHWASHER KITCHENAID KDFE104DWH4 "Replaced main control at customers request. F6E4 code, F8E2 code. Float switch and drain pump failure. Ran calibration/diagnostic cycle , passed. Operating as designed"
William L.
N/A N/A UNKNOWN2 "Delivered 16, returns received
Raymond D.
REFRIDGERATOR KITCHENAID n/a Replaced defrost timer. Tested unit. Unit functi9ns as designed. Cx will call back if unit continues.
Raymond D.
REFRIGERATOR WHIRLPOOL WRS325SDHZ01 Installed door. Instructed cx to defrost unit and let unit regulate to temps. Will call back if frost continues.
Raymond D.
DRYER MAYTAG MGD5630HC0 Replaced console. Tested unit. Unit functions as designed.
Raymond D.
WASHER MAYTAG MHW5500FW1
William L.
WASHER WHIRLPOOL WTW8100BW0 "F71, F72, found bearing loud , hub stripped, ordered hub, bearing kit & rps sensor for unit.; ordrng 1 W10435302 (bearing) and 1 W10820039 (hub) and 1 WPW10178988 (sensor)"
Tyler F.
WASHER WHIRLPOOL WGT4027EW0 Customer stated that the u it made a noise and now it won’t spin or drain. Ordering gear case and basket drive in stock.; ordrng 1 3360629 (gear case) and 1 W10820043 (brake & drive tube)
Tyler F.
REFRIGERATOR KITCHENAID KBFN502ESS01 Customer stated that the unit is powered but nothing is running. Found interface is not responding. Ordering interface not in stock.; ordrng 1 W10846767 (cntrl-elec)
Patrick C.
DRYER MAYTAG MGDB835DW4 Found the unit dead after customer used on her last cycle. Sufficient power getting to the unit. Thermal fuse reading open load on meter. Needs new fuse. Removed and replaced from stock. Tested unit. All ops checked good; used 1 WP3392519 (THERMAL FUSE) from stock
Patrick C.
OVEN AMANA AER6303MFS2 Removed and replaced control. Tested unit. All ops checked good
Michael M.
REFRIGERATOR WHIRLPOOL KSC23C8EYY02
Tom R.
WASHER MAYTAG MVWB725BW0 "Entered diagnostic mode, found no error codes. Ran Manual Activation, Found Spin and Soil buttons on UI not responding, confirmed in Operational Mode, running Auto Test. Auto test completed, no error codes, excessive movement in basket noted, customer states that noise is mainly during Spin. Order User Interface and Suspension.User Interface - (WPW10521059)Suspension - (W10247710); ordrng 1 W10247710 (washer,suspension) and 1 WPW10521059 (console)"
Michael M.
REFRIGERATOR KITCHENAID KBSN602EPA01 Cx was not home instructed to leave part by front doorW10323602Took quick pic job complete
Tom R.
DRIYER MAYTAG MGDB850YG3 "Ran unit, found ignition good, Flame reigniting during cycle good, temps low including Timed Dry Cycle High Heat, Order Thermostat.Thermostat - (WP8577274)NOTE - CONTACT ADDED, STICKY NOTES, HOME OWNER, WILL RESCHEDULE WITH HOME OWNER. RESCHEDULE CUSTOMER ON PART AND TIME AVAILABILITY.; ordrng 1 WP8577274 (thermistor)"
Tom R.
REFRIGERATOR ELECTROLUX EW23BC85KSAA "Entered diagnostics, found IM Evap Fan making chattering noise. Visual inspection shows ice build up around Fan. Order Housing Update Kit and Fan Motor.Housing Kit - (5303918784)Evap Fan - (5304493604); ordrng 1 5303918784 (air handler housin) and 1 5304493604 (fan & gasket kit)"
Michael M.
REFRIGERATOR WHIRLPOOL WRS555SIHZ00 Cx states ice maker was replaced but only made 1 or 2 harvest Tech finds temps set to recommended and ice cream is hard in FC Entered diagnostics and ran ice maker harvest. Found ice maker harness was not placed back correctly and was wrapped around ice maker tray preventing it from returning to home positionCorrected harness and ice maker harvested as designed and filled with water as designed. Advised cx wait 24 hours for ice productionSet temps to recommended unit ops are normal job complete
Tom R.
DISHWASHER JENN-AIR JDB9000CWP3 "Ran diagnostics, Recirculation Pump no longer activating. No error codes, ran unit in Normal Operation, no Pump activation. Hard reboot of unit, Pump activates in Normal Operation, but only on initial start up, does not Pump water after rinse cycle. Order Control Board, will return with Sump and Pump.Control Board - (W10909701); ordrng 1 W10909701 (cntrl-elec)"
Leon M.
REFRIGERATOR WHIRLPOOL WRF757SDHZ00 Replaced all selected parts.After running diagnostic check unit working properly as designed.
Leon M.
OVEN WHIRLPOOL WFG320M0BS3 Replaced all selected parts.After running diagnostic check unit working properly as designed
Steven W.
REFRIGERATOR MAYTAG MFI2570FEZ07 Ran diagnostics. Found water filter cover latch token. Needs filter cover. Instructed customer to have RO system bypassed by plumber.; ordrng 1 WP67006331 (cover-filt)
Leon M.
DRYER MAYTAG MGD6630HW0 Replaced all selected parts.After running diagnostic check unit working properly as designed.
Leon M.
DISHWASHER KITCHENAID KDTM404EBS0 Replaced all selected parts.After running diagnostic check unit working properly as designed
Leon M.
REFRIGERATOR JENN-AIR JFC2290REP00 Cx stated that unit has a rusty marks on the Stanley steal panel.
Lance V.
WASHER MAYTAG MVWB855DC2 "Failed drain pump motor, foreign object inside pump impeller causing overheating burning as drain pump is continuous trying to drain, water is not draining. Replaced drain pump, calibrated passed, auto test pass NO leaks. Unit now fully operational."
Raymond D.
REFRIGERATOR KITCHENAID KFIV29PCMS02 Need data loggers to monitor temps. Only way to be sure unit temps are perfect. ; ordrng 1 DATALOGGERS (CONTACT BILL)
Lance V.
DRYER WHIRLPOOL WED8500DC3 "Fixed-replaced faulty UI board due to start button not functioning during key encoder tests. Replaced and tested, unit now fully operational, all,ops complete"
Lance V.
DISHWASHER ELECTROLUX EWDW6505GS0 "Error code 03, checked code and verified, wash pump motor failure."
Lance V.
WASHER AMANA NTW4516FW3
Raymond D.
REFRIGERATOR KITCHENAID KSC23C8EYY02 Upon arrival FC evap frosted. Evap needs to be defrosted to test sealed system. Cx will defrost rescheduling for tomorrow.
Raymond D.
REFRIGERATOR KITCHENAID KRFF707ESS01 Need led module for repair.; ordrng 1 W11205083 (module)
Patrick C.
DISHWASHER KITCHENAID KDTM354DSS4 "Removed and replaced parts. Still having issues. Noticed that the harness going to the diverter motor was corroded. Unable to clean off. Needs new harness, as well as tube in the b; rqstng P&A on 1 W10752245 (harns-wire) and 1 WPW10340745 (tube-feed),
Kevin M.
REFRIGERATOR MAYTAG MFI2269FRZ02 "Unit not cooling in both compartments. I found low side sealed system leak in FC evaporator causing no cool. Unit needs compressor and evaporator. Removed and replaced evaporator and compressor. Vacuumed system down. Held vacuum. Charged system with 4.5oz of Freon. Tested unit. Pressures are good. Full frost pattern ; used 1 134A (4.5OZ 134A), and 1 AF1200 (TUBE EXTENSION)"
Kevin M.
OVEN WHIRLPOOL WOS72EC0HS01 Control panel freezes and has black lines through display and becomes non-responsive. Display resets. Failed user interface. Removed and replaced control panel. Tested unit. All tests good.
Patrick C.
REFRIGERATOR FRIGIDAIRE LFSS2612TE0 Found the unit having issues with the ice not dispensing. Needs new ice bucket. Broken not allowing ice to push thru
Patrick C.
LAUNDRY MAYTAG MVWB765FW3 Unit not working properly. Checked errors. Several for the lid lock. Checked latch function and it functions properly but the red light flashes or doesn’t show up. Then it acted like it didn’t want to have motor operations
Kevin M.
REFIRGERATOR KITCHENAID KRMF706ESS01 "Multiple issues. Unit is not making ice, frost in freezer, unit turning off and on and ice melting in ice bucket when it does make ice. I found out of range thermistor on ice maker, ice box fan not running at full speed, user interface has short causing unit to turn off and on, and needs new adapter kit to correct frost in freezer. Removed and replaced adapter kit, user interface, ice maker and ice box fan. Tested unit. All tests good."
Kevin M.
DISHWASHER WHIRLPOOL WDF320PADW3 Customer stated the unit would not fill but wash motor would come on. I tested unit and found float switch getting stuck in full position even with no water in unit. Removed and replaced float switch. Tested unit. All tests good.
Michael M.
DRYER WHIRLPOOL MGDC400VW0 Cx states drum is not spinningTech finds belt has come offRemoved front panel and observed pulley had broke in half on motor shaftNeeds motor 279827 and when 694089; ordrng 1 279827 (motordryer) and 1 WP694089 (wheel)
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFTR1814TBB "Found unit leaking water out the front. Everytime unit goes through defrost. Water will drain down the hose but hose was not installed in drain pan. Routed drain hose into drain pan. Tested unit. Unit is now working properly. Customer approves. ; (created new UIS, deleted prior attachment to UisID 220564)"
Kenneth M.
REFRIGERATOR HAIER HA10TG21SW Installed start device and tested unit. Unit is now working properly. Customer approves functions at this time.
Kenneth M.
REFRIGERATOR WHIRLPOOL WRF767SDHZ00 Installed water valves and heater. Tested unit. Unit is nlwmworking properly. Customer approves function at this time
Kenneth M.
WASHER GE GTW485ASJ5WS Installed board. Suspension and latch. Tested unit. Unit is now working properly. Customer approves function at this time
Kenneth M.
RANGE GE JK3800DH6BB "Upon arrival. Customer informed me that unit was not heating tested MW and oven. Both heated. Informed customer te hat no checks could be made at this time. Everything is working as designed. Informed customer if unit fails to give us a call back. Unit has ro be a failed state in order for us to properly diagnose. Customer approves all functions working at time of service. And if problem happens again. Customer will call us asap. No error codes found. ; (created new UIS, deleted prior attachment to UisID 220758)"
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFHT2032TP1 Installed evap fan motor and tested unit. Unit is now working properly. Customer approve function at this time.
Kenneth M.
RANGE AMANA AER6303MFB2
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFSS2615TE0 Installed overlay cover cover and gasket. Tested unit. Unit is working properly. Customer approves.
Lance V.
DRYER MAYTAG MEDX655DW1 "Vac at unit block terminal ok, heating element checked ok. Failed motor. Centrifugal switch is Faulty in motor causing unit to stop; ordrng 1 279827 (motordryer) and 1 WP694089 (wheel)"
Jonathan C.
REFRIGERATOR WHIRLPOOL WRS321SDHZ01 Installed valve tested working to spec
Jonathan C.
REFRIGERATOR FRIGIDAIRE LFSS2312TF0 Installed ICEMAKER tested working to spec
Lance V.
WASHER GE GTW330ASK1WW "Needs work, found broken lid latch assembly. Causing no agitating or spin. We will need to re route with parts. ; ordrng 1 WH01X24114 (lid lock)"
Lance V.
RANGE FRIGIDAIRE FFGH3054USA "Needs work- found faulty thermostat fuse, needs to be replaced. Causing no power to interface and controls.Need to re route with parts; ordrng 1 318578506 (thermostat)"
Jonathan C.
WASHER WHIRLPOOL WTW5000DW2 Found latch broken replaced tested working to spec
Lance V.
REFRIGERATOR KITCHENAID KRMF706EBS01 Needs work- found freezer compartment evaporator fan motor making loud noise and has failed causing no ice production. We will need to re route with parts.; ordrng 1 W11249952 (motor-evap)
Jonathan C.
RANGE WHIRLPOOL WFG505M0BS3 Found top came unclipped reinstalled top tested working to spec
Lance V.
LAUNDRY MAYTAG MVWB865GW0 "F8e1 error, F3e2, found faulty water valve, valve thermistor shorted causing no fill during regular wash cycle. We will need to re route with parts for repair.; ordrng 2 W11165546 (valve)s"
Jonathan B.
RANGE FRIGIDAIRE FGET3066UF Replaced defective motor. Tested unit and is working properly
Jonathan B.
WASHER WHIRLPOOL WFW5620HW0 Found loose connection to door switch. Fixed connection. Tested unit and is working properly
Kevin M.
WASHER WHIRLPOOL WTW5000DW2 Customer concerned with vibration and noise during spin cycle. I tested unit with load and found weak suspension and worn basket hub. Ordering parts; ordrng 1 W10528947 (drive hub kit) and 1 W11130362 (suspension)
Jonathan B.
WASHER MAYTAG MVWB835DW Found loose connection to water valve. Fixed connection. Tested unit and is working properly
John B.
OVEN WHIRLPOOL RBD245PDQ8 "Replaced the Control panel, the oven tested good. No, the control panel is now black. Due to the fact that white is no longer available. customer is OK with this.Paid check number 129"
Kevin M.
WASHER MAYTAG MVWB850YW1 Unit making loud noise during operation. I tested unit and found that the tub seal has failed and allowed water to wash out bearings causing noise. Unit needs bearing kit and hub. Please attempt to get additional labor for bearing job. Allow 1.5 hours on return. Ordering parts. ; rqstng P&A on 1 W10435302 (bearing) and 1 W10820039 (hub)
John B.
REFRIGERATOR WHIRLPOOL WRX735SDHV00 "Drip pan was leaking, replace the drip pan. The drain tube tested good no leaks problem solved customers happy with the unit."
Kenneth M.
WASHER MAYTAG MVWC415EW1 Found unit with long fill no fill error code. Found faulty water valve. Ordering new water valve. Valve just trickles in water. No blockage at filters; ordrng 1 W11210459 (Valve)
John B.
REFRIGERATOR KITCHENAID KRMF706ESS01 "It appears the roof freezer is not defrosting full of ice and frost, tested the heater and tested manual defrost cycle tested good. Replaced the sensor in the main control board, tested good."
John B.
OVEN AMANA AGR3300XDW0 "WPW10121631 122.57 labor 120.00 . Parts and labor, if they call back. They are thinking about getting a new oven so do not order any parts job is complete at this time."
Jim S.
REFRIGERATOR GE PFSS6PKXESS Replaced user interface. Unit tested ok
Joe M.
DISHWASHER WHIRLPOOL WDTA50SAHZ0 Customer decided to not proceed with service getting new unit. Job complete.
Jonathan C.
WASHER MAYTAG MVWX655DW1 Found hub stripped need wash plate because I can’t get it off going to have to cut it off ; ordrng 1 W10902814 (washplate)
Jim S.
ICE MACHINE ULINE U-CLR2160S-00 Replaced recirculating pump and drain pump. Found drain hose to drain pump restricted. Found air pressure hose crushed. Replaced both of those items
Jim S.
DISHWASHER GE GDT580SSF0SS Water sensor was dirty. Cleaned sensor. Unit tested ok
James M.
REFRIGERATOR WHIRLPOOL WRF535SWHZ Found u it not making ice. Replaced ice maker. Unit immediately filled with water. Unit is working as intended. Instructed customer to dump first 2 batches of ice. ; used 1 W10884390 (ICEMAKER) from stock
Jonathan C.
WASHER MAYTAG MVWC565FW0 Unable to remove agitator needs wash plate also; ordrng 1 W11161960 (agitator)
Jonathan C.
REFRIGERATOR KITCHENAID KFIV29PCMS03 Found 23 in freezer and 42 needs compressor and evap found bad spot on evap customer needs time; ordrng 1 8201675 (compressor) and 1 WPW10608485 (evaporator)
James M.
REFIRGERATOR MAYTAG MZD2665HEQ Found unit with clog in ice tray bin causing ice to get stuck. Removed ice from bin and tested unit. Auger good. Ice bin rotating. Refilled ice bin and unit now working as intended and dispensing ice as intended.
Jonathan B.
DRYER WHIRLPOOL CEM2745FQ0 Do not order parts. Found unit missing top of dryer .; ordrng 1 3347825 (plate) and 1 4396667 (insert) and 1 W10129843 (harns-wire) and 1 W10139100 (screw) and 1 W10461070 (bracket) and 1 W10461094 (panel-cntl) and 1 W10492412 (top) and 1 W10492415 (knob) and 1 W10510149 (bezel) and 1 W10662107 (light) and 1 W10845275 (overlay) and 1 W11089934 (panel-rear) and 1 W11097274 (switch-pts) and 1 W11244229 (slide-coin) and 1 W11283272 (door) and 1 W11315637 (lock-cam) and 1 WP3387974 (cam) and 1 WP3954812 (cushion) and 1 WP8576635 (bolt) and 1 WP90406 (nut) and 1 WPW10119283 (cover-term) and 1 WPW10133502 (lens) and 1 WPW10327105 (switch-cyc) and 1 WPW10521398 (timer)
Jonathan B.
OVEN WHIRLPOOL WFG505M0BS3 Found defective bulb.; ordrng 1 W10888179 (bulb-light)
James G.
WASHER MAYTAG MHW7100DW0 Replaced defective bellow Tested ok
James G.
RANGE WHIRLPOOL WGG555S0BS03 No leaks foundTested ok
James G.
WASHER SPEEDQUEEN TR3000WN "Upon arrival unit was stuck at rinse, found cold water supply off at wall. Opened water valve and retested Tested ok"
James G.
ICE MACHINE SCOTSMAN SCCG30MA-1US Reset unit control Tested ok No payment on site on maid there who knows both of payment
John B.
WASHER WHIRLPOOL WFW6620HC0 Error code F8E2 need more parts; ordrng 1 W11316246 (switch-wl) and 1 W11316255 (valve)
Isidore A.
WASHER WHIRLPOOL WFW8620HC1 "Pull out washer removed top panel, rear washer panel , old user interface and control board . Installed new control board, user interface and reinstalled panels. Test washer operation ok at this time, reinstalled washer in washer room. No codes found tried a rinse cycle ok."
Joe M.
REFRIGERATOR WHIRLPOOL WRX988SIBM03 Unit is not cooling due to a weak fan. Ordering adapter; ordrng 1 W10864518 (ICE BOX FAN)
Joe M.
COOKTOP IKEA ICR555DB01 Units transformer shorted causing it to take the tod and transformer with it. Ordering parts.; ordrng 1 W10464566 (TOD) and 1 W11028268 (APPLIANCE MANAGER ) and 1 WP9760588 (TRANSFORMER)
Isidore A.
DRYER MAYTAG MGD8200FW1 "Found venting needs to be cleared, advise to get professional duct cleaning service. To correct vent duct"
Joe M.
REFRIGERATOR WHIRLPOOL WRF550CDHZ01 Water reservoir is destroying water filters; ordrng 1 EDR4RXD1 (FILTER) and 1 W11346622 (WATER RESERVOIR ASSEMBLY )
Isidore A.
WASHER ROPER RTW4516FW2 "Found F8E1 not filling with water verified and F0E5 out of balance error verified right side suspension rod W10780045 failure. Removed console and main top , old suspension rods and water valve W11210459. Installed new suspension rods and water valve, reinstalled console and top panel. Test washer operation ok at this time working as designed."
Irvin F.
DISHWASHER WHIRLPOOL WDT730PAHZ0 "X says the 7nit is not operating properly. NO ERROR CODES ALL FUNCTIONS GOOD. CX INSTRUCT, features loading and rinse aide. Main issue wet dishes. Unit needs rinse aid. Instruct cx to purchase and put into the dispenser. All ops normal."
Irvin F.
DRYER AMANA NED4655EW1 WPW10237959 DOOR SWITCH actuator broken. Able to activate dryer operates properly. Need door switch. Replaced door switch. P/U parts from marcone. All ops normal.
Irvin F.
REFRIGERATOR WHIRLPOOL WRX735SDHZ01 "Cx says the handle has popped of the frezer door several times. The filter is not allowing water to pass. Replaced the handle, and filter. Installed square to activate door switch. All ops now normal."
Irvin F.
WASHER MAYTAG MVWC415EW1 Cx says the dispenser cap fall off during the cycles. Only issue.
James M.
DISHWASHER WHIRLPOOL KUDE70FXSS5 Fund unit with leak on left hand side of door. Checked door seal and found it to be worn in small spots along left side. Ordering new seal. Also found led indicators on control board not working on cycle selection. Ordering replacement control panel. ; ordrng 1 W10300924V (door seal) and 1 WPW10481144 (panel-cntl)
Irvin F.
REFRIGERATOR FRIGIDAIRE FFHT2032TP1 "Cx say the unit is making a light vibration sound from the frezer section. Confirmed issue. Removed panel inspected found the gromet holding the motor is cracked not holding the fan motor. Replaced rear grommet. Powered unit fan noise normal, vibration gone. ; used 1 242287501 (GROMET REAR) from stock"
Hector Z.
DISHWASHER KITCHEN AID KDTM404ESS3 Customer stated dishwasher door not closing properly. Checked unit and adjusted front legs. Tested ok.
James M.
REFRIGERATOR WHIRLPOOL WRF993FIFM00 "Found unit with hard to remove filter. Found filter bracket not aligning and causing filter to get stuck. Removed filter and realigned bracket, inserted and removed filter several times. Filter now removable. Also found ice door not making full contact on ice bin area causing ice buildup under bucket. Ordering new ice door. Will return 11-26 to install. ; ordrng 1 W10702031 (door-ice)"
James M.
REFRIGERATOR FRIGIDAIRE FFSS2615TS Found unit making door alarm at random times. Ordering new control. Will return 11-22 to install. ; ordrng 1 A01078804 (control)
Hector Z.
WASHER MAYTAG MVWB765FW3 Customer stated washer not finishing the cycle. I ran a manual diagnostic test and the cold/hot water solenoid were not dispensing water. Replaced the water valve (W11172234). Tested ok.
Hector Z.
WASHER WHIRLPOOL WTW7500GC0 "Replaced: Left Hinge (W10861714), Right Hinge (W11023747), Lid Hinge (WP8563965), Lid Hinge (WP8572974), Lid (W11130236), and Screws (WPW10078270). Tested ok."
James M.
DRYER WHIRLPOOL MED6630HW Found unit with loud noise during cycle due to blower wheel. Ordering new blower wheel and dryer repair kit to install during return visit. Unit is stacked and customer made aware of need to have u it unstacked for return visit. ; ordrng 1 WP697772 (blower wheel)
James G.
OVEN WHIRLPOOL WOD51ES4ES00 P7 connector on board to check switches Tech line says if switches check good then board is defective ; ordrng 1 W10807576 (cntrl-elec)
George Y.
OVEN WHIRLPOOL WEG745H0FS0 Installed part tested check out ok complete.
George Y.
DISHWASHER KITCHENAID KDTE334GPS0 Found dishwasher not powering up found junction box power wire not making contact rethighten connectors retested check out ok complete.
James G.
MICOWAVE OVEN FRIGIDAIRE FFMV1645TS High voltage circuit buzzing TWO MAN JOB ; ordrng 1 5304509453 (CAPACITOR ) and 1 5304509470 (MAG) and 1 5304509476 (TRANSFORMER) and 1 5304509478 (CAP) and 1 5304509479 (DIODE)
James G.
OVEN WHIRLPOOL WFG550S0HZ1 Hinges bent; ordrng 1 WPW10299224 (hinge-door) and 1 WPW10299227 (hinge-door)
Francisco S.
REFIRGERATOR MAYTAG MRT311FFFM00 Different issue. Che led unit it developed a gap on top fc door. Removed frost with steam gun and heat treated gasket for a proper seal. Unit now checks ok.
Francisco S.
RANGE AMANA AGR5330BAW3 Checked unit found now right side hard to ignite. Removed and replaced burner top unit now working properly.
James G.
WASHER SPEEDQUEEN AWN432SP113TW04 Idler pulley frozen APPROVED NEED PRICING ; ordrng 1 959P3 (KIT)
Francisco S.
MICROWAVE KITCHEN AID MODEL Advised cx on replacing unit
Francisco S.
DRYER MAYTAG MGDB835DW4 Checked unit found no error codes. Good air flow and temp checks ok on exhaust vent. Cx stated to only have an issue with big comforter. Explained to her how auto sensing cycles work and advised to use timed dry for this items. Adjusted dryness level to 3 and unit checks ok at this moment.
James G.
RANGE AMANA ACR4303MFW3 Control dead; rqstng P&A on 1 W10904901 (cntrl-elec)
James G.
OVEN THERMADOR PG484GGEBS-02 should fix both ovens; ordrng 1 00709786 (BOARD)
Francisco S.
REFRIGERATOR KITCHENAID KBFN502ESS02 Checked unit found some bad led module lights. Removed and replaced lights unit now working properly.
Francisco S.
DISHWASHER KITCHENAID KDTE334GPS0 Checked unit found missing screw on toe panel. Installed panel properly unit now checks ok. Cx had question regarding installation. I referred her back to her installation company.
Erick S.
WASHER WHIRLPOOL WTW8040DW Installed new parts on unit. Retested it and it passed all tests. Job complete
Erick S.
WASHER WHIRLPOOL WFW560CHW0 "Cycled unit and found bad drain pump causing failure AND DOOR not to open. Drained water and replaced pump. Retested it, it drain and door unlocks, unit passed all tests. Job complete"
Isidore A.
REFRIGERATOR WHIRLPOOL KRFF305EWH00 "Remove fresh side shelves, not able to duplicate leak. Water was turned off, water turned back on, test water dispenser and icemaker fill no leaks, fill to icemaker not filling; ordrng 1 WPW10420083 (valve)"
Erick S.
REFRIGERATOR WHIRLPOOL WRX735SDHZ01 Installed new parts on unit. Retested and valve and icemaker filling. All components are working at this moment. Job complete
Erick S.
DRYER MAYTAG MEDB835DW4 Cycled unit and found unit with kinked exhaust causing it to short cycle. Straighten out vent hose. Realigned dryer. Unit is now cycling correctly. Informed customer may need professional to clean vent since it has not been serviced as well Job complete
Erick S.
OVEN WHIRLPOOL WOD51EC0HS01 Removed oven from wall.Installed new parts on unit re-tested it and it passed all test no errors. Reinstalled unit and secure trim.Job complete
Erick S.
DRYER WHIRLPOOL WGD5000DW3 Installed new timer on unit. Re-tested it and it passed all test. Job com
Enrique R.
REFRIGERATOR FRIGIDAIRE FFHB2740PPAA Installed ice maker and thermostat . All functions tested normal . No leaks .
Irvin F.
DISHWASHER KITCHENAID KDFE204EWH0 "7/1-heating element water heating issues. During diagnostics cycle the diverted motor lost position, won’t set to next cycle. The motor ; ordrng 1 W10605058 (pump&motor) and 1 W10790702 (cntrl-elec)"
Enrique R.
WASHER MAYTAG MVWC415EW1 "Inspected Maytag washer . Customer concerns , unit not draining . Found hair pin obstructing impeller . Removed obstruction . All functions tested normal ."
Enrique R.
KITCHEN WHIRLPOOL WFG540H0ES1 Installed new parts . All functions tested normal .
Hector Z.
DRYER WHIRLPOOL MGD6630HW0 "Customer stated the appearance of the F3E3 code (Shorted Thermistor). I set the unit in diagnostic and the code was there, erased the code F3E3. I tested all the components involved in the circuit; ordrng 1 W11157861 (harns-wire) and 1 W11396709 (THERMISTOR) and 1 WP8577274 (thermistor)"
Enrique R.
WASHER GE GTW460ASJ4WW "Inspected GE washer . Customer concerns , unit not draining all the water out . In diagnostics found drain pump fault . Installed new pump . Ran small wash cycle test . All functions tested normal"
Enrique R.
OVEN WHIRLPOOL WFG525S0HS1 Inspected whirlpool range . Customer concerns control not powering on . Installed new control . All functions tested normal .
George Y.
DRYER GE GTD42GASJWW Customer had reschedule for others date
Darren A.
REFRIGERATOR WHIRLPOOL WRS312SNHM01 "Controls confusing, freezer is controlling air flow to fresh side, reset controls and instructed client."
Darren A.
REFRIGERATOR FRIGIDAIRE FFHS2611LBRA "Ice maker fill tube spilled onto fan, removed ice and taped fill tube to stop spilling."
Darren A.
DRYER MAYTAG MEDX655DW0 "Squeaky rollers, installed repair kit, checked out okay.; used 1 4392065 (DRYER REPAIR KIT)"
George Y.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 Found refrigerator water dispenser very slow pressure need to replace valve ok to order.; ordrng 1 EDR4RXD1 (water filter) and 1 W11043013 (valve)
Darren A.
WASHER AMANA ADB1400AGW1 "Adjusted door catch to latch properly , closes and locks normally."
Danny G.
RANGE WHIRLPOOL WFG505M0BS3 No light no oven Replaced control and test oven and light is working and unit is heating properly
Danny G.
DRYER WHIRLPOOL WGD4850HW0 Broken seal Replaced and install repair kit and rear drum seal Reinstall unit and test unit and dryer is working properly
Danny G.
DRYER WHIRLPOOL WGD4815EW2 Unit is not cooling Found faulty start device Replaced start device and power unit and unit kicked onAdvised client to allow 24hrs for unit to reach proper temperature
Dane K.
DRYER WHIRLPOOL WGD5000DW Upon arrival the unit was not heating. Found the igniter cracked. Removed and replaced igniter and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR FRIGIDAIRE FFTR2021TB Removed and replaced compressor condenser and filter dryer and recharged and tested unit. Unit functions normal now
Dane K.
STOVE WHIRLPOOL DID NOT SERVICE Cxsaid thier oven worked fine
Enrique R.
DRIYER WHIRLPOOL WED5000DW2 "Inspected whirlpool dryer . Customer concerns , unit not powering on . Found shorted thermal fuse , and also need door switch . Didn’t have one in my vehicle .; ordrng 1 WPW10569603 (switch-dor)"
Cruz B.
WASHER MAYTAG MHW5630HW0 "Fixed for FTC- found error code f6e2 displaying at UI, Communication error between cntrl and UI, i then installed new part (cntrl elec), ran a quick cycle, it filled, wash, drain, spin, locked and unlocked, no codes, no leaks, cx ok repair."
Enrique R.
RANGE WHIRLPOOL WFG505M0BS3 "Checked control wire connectors to chassis ( continuity ) . Techline instructed me to replace main wire harness . ; ordrng 1 W10836473 (harns-wire) and 1 W10914403 (harns-wire) and 1 W11173616 (cord-power) and 1 W11176454 (igntr-oven)"
Cruz B.
WASHER WHIRLPOOL WTW8040DW4 "Fixed- installed new parts (cntrl elec, panel) calibrated for wash performance, ran diagnostic test mode it completed filled, wash, drain, spin, locked & unlocked, cleared code, no leaks, cx ok repair."
Cruz B.
DRIYER ELECTROLUX EFME617SIW0 "Fixed- installed all new parts (thermostat, heater, limiter, grill ass, main cntrl) ran unit in a high heat cycle it heated fine, run quiet, cx ok repair."
Chris M.
DRYER WHIRLPOOL WHD5090GW0 Upon arrival replaced control board for the second time. Entered Heat pump dryer into diagnostics ran multiple test all functions tested good. Informed customer all test passing dryer is now functioning. If dryer starts acting up Again to contact us so we can contact whirlpool tech line.To see how they want to proceed. Job complete
Enrique R.
WASHER WHIRLPOOL WFW560CHW0 "Inspected whirlpool front load washer . Customer concerns , not operating ; ordrng 1 W11322879 (cntrl-elec) and 1 W11325580 (cntrl-elec)"
Darren A.
REFRIGERATOR GE GNE27JMMAFES Ordered ui for intermittent door switches.; ordrng 1 WR55X30267 (switch)
Chris M.
REFRIGERATOR WHIRLPOOL WRS588FIHB00 upon arrival removed and replaced freezer door.Routed wires and water lines so they would not rub out or pinch. Made Sure door Was aligned properly and sealed so no cold get out.Powered unit on ran test 45 which is icemaker fill test everything checks out good. Job completed
Chase F.
DRYER WHIRLPOOL WED4815EW1 Diagnosed a dryer cx concerned about noise coming from venting. Vent hose is to long and crinkled not allowing for air to flow from out of machine properly. Cut down venting and adjusted also cleared all debri. All specs now testing normal ops. Job complete.
Darren A.
OVEN MAYTAG MGR6600FZ1 "Oven will not relight over 400 degree, ordered igniter,harness and dis module.; ordrng 1 W11161843 (harns-wire) and 1 W11162730 (module-spk) and 1 WP9758079 (igntr-oven)"
Chase F.
DRYER WHIRLPOOL WGD49STBW2 "Diagnosed a whirlpool dryer. Found lint built up in duct. Removed all lint. Tested unit, all specs now testing normal and unit is heating with no problems. Job complete."
Chase F.
WASHER WHIRLPOOL MVWB765FW3 "Found multiple objects stuck underneath washplate. Repmoved objects and tested unit. All specs now testing normal and unit now spinning smooth."
Darren A.
DISHWASHER WHIRLPOOL WDT970SAHZ0 "Heater will run in diagnostics but not heating during cycle, ordered control.; ordrng 1 W11305296 (cntrl-elec)"
Chase F.
WASHER AMANA NTW4516FW3 "Installed new pump, tested unit. All specs now testing normal, job complete."
Darren A.
DISHWASHER GE GDF510PGM0BB "Unable to get a recording"
Chase F.
RANGE FRIGIDAIRE FFGF3016TBA Installed new clock and overlay. Tested unit. All specs now testing normal. Job complete.
Darren A.
REFRIGERATOR KITCHENAID KFIV29PCMS00 "RC evaporator iced over, ordered cover and thermistor.; ordrng 1 W11211387 (cover-evap) and 1 WPW10277799 (harns-wire)"
Chase F.
MICOWAVE OVEN FRIGIDAIRE FGMV176NTDB M/S pics are attached via quick pics
Danny G.
REFRIGERATOR KITCHENAID KBSD608ESS01 Light changes and keeps on flashing on dispenser Found faulty dispenser control ; ordrng 1 W10151236 (cntrl-elec)
Cesar H.
LAUNDRY WHIRLPOOL WTW7500GW0 Replaced water valve unit tested good
Danny G.
WASHER WHIRLPOOL WTW4955HW0 Unit is making loud noise when spinning and bouncing all over the placeFound weak suspension and laud gearcase on spin cycle Need to order parts and rs call; ordrng 1 W10680215 (washplate) and 1 W11035747 (gearcase) and 1 W11217817 (suspension)
Cesar H.
WASHER WHIRLPOOL WTW5000DW0 "Replaced wash plate, gear case, and hub. Calibrated and tested unit all checked good"
Andy H.
WASHER MAYTAG MVWC565FW1 "Leaks water and oil, replaced gearcase,agitator,actuator,cam,belt tested unit working good."
Andy H.
RANGE WHIRLPOOL JGRP548WP01 Blower not working. Replaced blower and tested unit working properly
Cruz B.
STOVE KITCHENAID KCED600GBL01 Need more work ; ordrng 1 W11051484 (cooktop)
Andrew P.
DISHWASHER WHIRLPOOL KDTM354ESS3 Removed and replaced upper track. Tested ok. Cx paid service call on prior visit.
Andrew P.
REFIRGERATOR WHIRLPOOL KBSD608ESS01 Cx stated water line sticks out from under fridge. Attached excess water like to clips under fridge. Water line now stays in place.
Alejandro C.
REFRIGERATOR GE GFE29HSDISS "Found the unit not cooling normal,replace condenser fan motor running normal, check compressor and evaporator fan motors running normal"
Cruz B.
DISHWASHER FRIGIDAIRE FGID2466QF6A "Needs more work- found rack adjusters to be getting stuck on tracks, found wheels to be coming off, found springs from door to be squeaking when cx opens the door, cx states unit is cleaning dishes, ordering parts for unit. Cx is requesting a 3-6 time frame. ; ordrng 2 154578801 (cable)s and 2 154579101 (spring)s and 1 5304506530 (rack adjustment) and 1 5304506531 (rack adjustment)"
Chris M.
WASHER WHIRLPOOL WTW5000DW1 Cx wash machine was not finishing cycle. Also making loud grinding noise at times close coming out wet etc.I first entered washer into diagnostics Received multiple codes dealing with lid latch and Control board. Found suspension to Pretty worn out also found plastic shavings from Drive pulley being loose; ordrng 1 W10721967 (drive pulley) and 1 W10837741 (lid strike) and 1 W10913953 (actuator) and 1 W11116590 (cntrl-elec) and 1 W11130362 (suspension) and 1 W11307244 (latch)
Alejandro C.
REFRIGERATOR WHIRLPOOL WRX988SIBM01 "Found the unit not cooling,verify problem ff evaporator leaking refrigerant, need evaporator, drier uv, housing"
Chris M.
WASHER MAYTAG MVWB855DC3 Upon arrival ran washer into diagnostics received multiple error codes dealing with consul and control board. Noticed numerous buttons are not responding to touch also lid latch is starting to fail; ordrng 1 W10861642 (latch) and 1 W11112662 (console) and 1 W11171748 (cntrl-elec)
Chase F.
REFRIGERATOR FRIGIDAIRE FFTR1814QW6B "Found worn gaskets in RC and FC not allowing for doors to seal properly. Ordering new gaskets.; ordrng 1 242193203 (gasket-frzr door) and 1 242193206 (gasket-refr door)"
Aaron B.
WASHER WHIRLPOOL WTW4816FW2 "Checked operations unit is working correct , customer wash the comforter and it got off kilter unit is working as designed not meant for a comforter advise customer with an agitator version they have to wait in the loads greatly and I’ll comforters and huge rugs need to go to the laundry mat"
Aaron B.
WASHER WHIRLPOOL CAE2745FQ1 "Replaced the main board actuator and pulley assembly , tested operations normal"
Aaron B.
MICROWAVE MAYTAG MMV1174FZ2 "The unit sometimes will not turn on when pressing start clock time will show again and not turn on tested for ten minutes no malfunction happened at this time. Checked operations normal , tested ops ok at this time unable to verify any problems at this time"
Aaron B.
DISHWASHER KITCHENAID KDTE334GPS0 "Checked unit the upper rack tracks welds separated the unit off of the rack , found the service flash Tall Tub Dishwashers Upper-Rack Rails Separating
Aaron B.
REFRIGERATOR WHIRLPOOL WRT541SZDW00 "Checked operations unit not cooling in the fresh food section and freezer not maintaining in the freezer , found seized up evaporator fan motor not running and not pushing air to the fresh food section just maintaining the freezer section a little bit and total food loss verified in the fresh food section.Replace the evaporator fan motor tested operations unit will work as designed give 24 to 48 hours for normal temps to come back; used 1 WP2315539 (MOTOR-FAN)"
Aaron B.
REFRIGERATOR WHIRLPOOL WRS315SNHW01 "Nothing found wrong with the unit at this time customer says it buzzes intermittently when starting up and other times , unable to find an issue at this time"
Cesar H.
REFRIGERATOR KITCHENAID KSSC48QVS02 Failed ice dispenser motor has 120v at motor will not run winding ohm open rerouted for dispenser motor ; ordrng 1 W10271509 (motor)
Cesar H.
WASHER WHIRLPOOL WFW92HEFW0 Found dispenser has water pooled in it after a wash checked dispenser syphon not working properly dispenser is clean rerouted for new dispenser ; ordrng 1 WPW10250742 (drawer)
Andy H.
FREEZER WHIRLPOOL WRX735SDHZ01 Too cold in fresh side compartment and door making a noise and not closing properly ; ordrng 1 W10918010 (closer) and 1 WP12028505AP (ref dr closer cam)
Andy H.
OVEN WHIRLPOOL CWG3100AAE Need more time to troubleshoot
Aaron B.
WASHER MAYTAG MVWB765FW3 "Checked the unit , now will not fill tested washer in agitating ok at this time ordered parts to repair unit , then I’ll retest ; ordrng 1 W11165546 (WATER VALVE) and 1 W11172234 (HOUSING)"
William L.
REFRIGERATOR KITCHENAID KRFF507HPS00 "Replaced freezer led module, all leds functional , ordered auger motor & ui panel.; ordrng 1 W10822606 (motor) and 1 W11228269 (panel-ui)"
Tyler F.
OVEN WHIRLPOOL KEBK276BSS01 Ordering main control in stock.; ordrng 1 WPW10317345 (cntrl-elec)
Tyler F.
WASHER MAYTAG MGDB850YG3 Customer stated that the dryer is not heating found failed gas coils. Ordering gas coils in stock none on truck.; ordrng 1 279834 (2 coil gas valve set)
Tyler F.
OVEN WHIRLPOOL KEBK276BSS01 Ordering main control in stock.; ordrng 1 WPW10317345 (cntrl-elec)
Tyler F.
WASHER MAYTAG MGDB850YG3 Customer stated that the dryer is not heating found failed gas coils. Ordering gas coils in stock none on truck.; ordrng 1 279834 (2 coil gas valve set)
Tom R.
WASHER MAYTAG MVWB835DW4 "Entered diagnostics, found error codes F5E1, F0E3. Ran diagnostic tests, Lid Lock good, water flow good, agitate good, drain good, spin good. One attempt at Lid Lock in diagnostics not successful, order Control Board. Visual inspection of tubs shows no black debris or residue, customer states they do not have a maintenance product for their machine. Recommended annual maintenance product be used in machine, black residue politely from detergent build up in machine.Control Board - (W11170706)NOTE - UNDER 1YR, POP PHOTO ATTACHED; ordrng 1 W11170706 (CNTRL-ELEC)"
Tom R.
WASHER WHIRLPOOL MVWB766FW1 "Installed Water Valve and Control Board, override error code of F2E3 present, no UI interaction possible. Reinstalled previous Control Board, unit functional. Order Control Board and UI.Control Board - (W11135392)User Interface - (W11135391); ordrng 1 W11135391 (CONSOLE) and 1 W11135392 (CNTRL-ELEC)"
Tom R.
REFRIGERATOR WHIRLPOOL GX5FHTXVQ03 "Ran diagnostics, Evap Fan good, Damper Door good, Thermistors good. Found no air leaks in either compartment. Frost pattern irregular, possible leak, visual inspection of drainage system shows oil in drainage system, order Compressor, Drier, and Evap Coil.Compressor - (W10233960)Evap Coil - (WPW10317014)NOTE - RESCHEDULE WITH SEALED SYSTEM TECH, RESCHEDULE ON PART AND TIME AVAILABILITY.; ordrng 1 W10233960 (compressor) and 1 WPW10317014 (evaporator)"
Tom R.
DRYER GE GFD43GSSM1WW "Customer states a metal scraping noise after heating up. From previous experience, tech applied pressure to back of machine, reproducing the noise, customer confirms. Drum Shield in rear of machine scraping Drum from heat expansion, replace Drum Shield. Order Drum Shield, no signal, reschedule customer on part and time availability.Drum Shield - (WE14X21174)NOTE - PART NUMBER FROM RELIABLE, NO SIGNAL AT CUSTOMER LOCATION, RESCHEDULE CUSTOMER ON PART AND TIME AVAILABILITY.; ordrng 1 WE14X21174 (DIFFUSER)"
Timothy J.
M/W OTR WHIRLPOOL WMH32519HZ1 Partial display. Unit needs a control board UI and a interlock assembly. Door closure issues.; rqstng P&A on 1 W11333816 (UI(DISPLAY))
Timothy J.
RANGE FRIGIDAIRE FGGF3036TF Installed probe tested unit unit still under temp by about 30f now. Unit needs a new control.; rqstng P&A on 1 316419378 (OVERLAY) and 1 5304516044 (EOC)
Timothy J.
RANGE WHIRLPOOL WEG730H0DS0 Unit is showing a 8-0(cooling fan) code. ; rqstng P&A on 1 W11107275 (fan-blwr)
William L.
DRYER MAYTAG MEDX655DW1 "Replaced timer, Found intermitent voltage from centrifugal switch on motor, unit needs motor replaced, cx talking to Lowe’s during job, cx having unit replaced by dealer. Customer no longer wants unit repaired, cx refused further repairs."