Local Reviews
Powered by Fluid LOCAL
Raymond H.
MICROWAVE JENN-AIR JMW2430DP01 "Replaced control panel and tested, unit functions as designed."
Randy C.
DRYER - ELECTRIC WHIRLPOOL WGD5000DW3 Found not stopping after cycle. Removed and replaced timer. Testedunit. Now shuts off. Cx approves job complete
Tom R.
REFRIGERATOR FRIGIDAIRE LFHB2751TF4
Randy C.
REFRIGERATOR KITCHENAID KSSC42QVS05 Found not dispensing ice motor failed ice bin stuck. Defrosted with streamer removed and replaced bin and motor now working as designed job complete
Tom R.
REFRIGERATOR FRIGIDAIRE LFSS2312TE0 "Entered diagnostics, ran Compressor, customer identifies noise, checked Condesner Fan, Fan secure, Fan functional. Reschedule with sealed system tech, order Compressor, Drier, and Evaporator Coil.Compressor - (241650212)Evaporator Coil - (5303918286)Drier - (5303305677)NOTE - SEALED SYSTEM TECH REQUIRED; ordrng 1 241650212 (compressor & gromm) and 1 5303305677 (drier/filter) and 1 5303918286 (evaporator)"
Randy C.
RESIDENTIAL REFR KITCHEN AID KRMF706ESS01 Removed and replaced parts. Now working as designed wll lights turn on.
Randy C.
WASHER MAYTAG MVWB835DW1 Removed and replaced water valve housing and lid lock. Now working job complete
Randy C.
REFRIGERATOR KITCHENAID KRSC503ESS01 Found unit not dispensing ice. Found bad motor removed and replaced part now working as designed
Timothy J.
REFRIGERATOR WHIRLPOOL WRF767SDEM01 Inspected unit and found frost on the FC evaporator. Removed evaporator panel and inspected the evaporator. Defrosted FC and checked door gasket. Door gasket ok. Evaporator has a full frost pattern. IM stuck mid harvest. No VAC to the IM. Ordering Stealth board.; rqstng P&A on 1 W11092503 (panel-ui)
Timothy J.
REFRIGERATOR WHIRLPOOL WRS325FDAB06 The harness I receive is not the part in the unit . I have to tape that to get it to stay. The Flat LED has 120vac input and 7VDC output. I checked continuity through the harness and found it is ok. I will need 2 tapered lens LEDs to finally complete this job.; rqstng P&A on 2 WPW10515057 (light)s
Patrick C.
REFRIGERATOR WHIRLPOOL WRS571CIDM02 Removed and replaced fan. Tested unit. All ops checked good
Patrick C.
REFRIGERATOR WHIRLPOOL GD25DFXFW02 Found the unit having issues with ice maker. Not cycling properly. Needs new ice make. Getting power and no harvest. Removed and replaced from stock. Tested unit. All ops checked good ; used 1 4317943 (ICEMAKER) from stock
Patrick C.
OVEN WHIRLPOOL WFG550S0HZ1 Found the unit not heating and the tops burners are to high. Adjusted the top burners for the customer and checked heating out. The connector for the bake ignitor not connected. Reconnected and secured. Tested unit. All ops checked good
Patrick C.
DRYER AMANA NGD4655EW2 Found the front panel just barely hanging on the cabinet. Fell off delivery truck. Needs to be secured. Secured the panel and top as well. Tested unit. All ops checked good
Patrick C.
REFIRGERATOR WHIRLPOOL ED22PWXAN11 "Removed and replaced ice maker, tube, and fitting. Tested unit. All ops checked good"
Rod H.
REFRIGERATOR WHIRLPOOL WRF767SDEM01 Iced over ffd evaporatorConfirmed Excessive ice buildup indicates ffd defrost had failed requiring harness/fan kit and control replacement.; rqstng P&A on 1 W10843055 (cntrl-elec) and 1 W11033168 (harns-wire) and 1 WPW10389152 (support)
Patrick C.
WASHER MAYTAG MHW6630HC0 Found the clamp popped off of bellow. Reinstalled tested unit. All ops ch3dked good
Leon M.
WASHER MAYTAG MHW8100DW0 Replaced drain pump.After running diagnostic check unit working properly as designed.
Leon M.
DISHWASHER KITCHENAID KDTE204GPS0 Replaced drain pump and motor assembly with control electric board.After running diagnostic check unit working properly as designed.
Raymond H.
REFRIGERATOR KITCHEN AID KRFC704FSS00 Cx paid for water filter. Upon arrival unit not making ice and door seal tearing. Found magnet falling out of seal and water filter restricted causing low ice and minimal water dispenser.; ordrng 1 F2WC9I1 (filter) and 1 W10917313 (gasket-dor)
Lance V.
LAUNDRY WHIRLPOOL WTW5000DW2 "Fixed-found wash plate loose. Removed wash plate and inspected, checked ok. Installed wash plate and tightened. Ran calibration and passed, auto test passed. Unit is now fully functional."
Lance V.
WASHER WHIRLPOOL WFW6620HC0 Fixed-replaced hot and cold water valves and pressure switch. Ran and tested No leaks No errors. All checked ok.
Raymond H.
FREEZER KITCHENAID KRMF706ESS01 "Replaced brackets, cx stated that ice maker stopped working as well. Found ice maker stop cycling half way through and then intermittently rotates, need ice maker.; ordrng 1 W11294907 (icemaker)"
Lance V.
LAUNDRY WHIRLPOOL WTW8040DW4 "Fixed-replaced faulty valve assembly as well as control board. Ran and tested, no leaks. Washer is now filling and fully functional, all ops complete"
Raymond H.
REFRIGERATOR WHIRLPOOL WRS325FDAM04 upon arrival unit had a small crack in liner flow. Also lights are dim and intermittent. Found Light switch not fully opening. Needs switch and repair kit.; ordrng 1 WP2149705 (switch)
Lance V.
WASHER WHIRLPOOL WTW7500GC2 "instructed customer on use of spin options. Customer had set “No” spin during wash, which saves the setting and does not spin and leaves clothes wet. Advised, customer to check all settings before selecting and starting a cycle, this will ensure any mistakes of selecting “no spin”. Unit fully functional, passed auto test, fully draining."
Lance V.
MICROWAVE OVEN FRIGIDAIRE FFMV1645TS "Fixed-replaced fuse, monitor switch, capacitor and diode. Ran and tested, unit is now fully functional. Heating ok, all ops complete"
Lance V.
REFRIGERATOR WHIRLPOOL WRS325SDHW01 "Fixed-found faulty ice maker, 120v to ice maker and not cycling. Replaced with “truck stock” 4317943, cycled and tested ok. Allow up to 36hrs for ice production, all ops complete; used 1 4317943 (ICEMAKER) from stock"
Lance V.
REFRIGERATOR WHIRLPOOL WRF535SWHZ01 "Fixed-replaced control damper, tested ok. All fully functional."
Lance V.
REFRIGERATOR WHIRLPOOL WRS571CIHZ01 "Fixed-found ice formation patterns on right side top freezer as well on ice bin housing. Warm air entering.Removed all ice, Adjusted ice bin housing to close gap, as well as heated and formed door seal for a complete seal."
Lance V.
DRYER MAYTAG MGDB850YG2 "Fixed-replaced faulty pulley. Installed dryer repair kit, with new rollers and belt. Ran and tested ok, sounds all normal. Fully functional."
Lance V.
WASHER MAYTAG MVWX655DW0 "Fixed-found wash-plate teeth worn out, causing it not to function during agitation. Inspected gear case and checked ok. Replaced wash plate and cap. Calibrated unit, passed. Unit now fully functional. All ops complete."
Patrick C.
REFRIGERATOR WHIRLPOOL WRF550CDHZ00 "Found the unit having issues with not getting cold enough. Checked damper and it keeps opening and closing. Needs new damper and control, damper was recently replaced ; ordrng 1 WPW10312695 (electronic control)"
Kevin M.
WASHER MAYTAG MVWC565FW0 Unit not finishing cycle. I found code for basket spin speed sensor. I tipped unit back and found gearcase pulley loose and causing error code. I removed pulley bolt and applied lock tight to bolt per manufactures specs. Tightened pulley bolt to manufactures specs. Tested unit. All tests good.
Patrick C.
REFRIGERATOR KITCHENAID WRV986FDEM "Customer:er having issues with the units ice maker in fridge clumping up. Ice box fan not running. Checked dispenser motor and it was stalled, getting power needs motor and fan; ordrng 1 W10822606 (motor) and 1 W10846539 (evaporator fan blade)"
Kevin M.
WASHER WHIRLPOOL WFW7590FW0 Customer stated unit stopped mid cycle. I put unit into diagnostic and found error code f8e3. I removed air gap and cleaned rubber flash on pressure hose causing false pressure readings. Tested unit through diagnostic. All tests good.
Patrick C.
REFRIGERATOR WHIRLPOOL WRX735SDHW00 Found the unit still having issues with freezing items. Checked out and found thermistor in ice box out of rang. Needs new thermistor and control ; ordrng 1 W10884720 (harns-wire) and 1 W11043763 (cntrl-elec)
Kevin M.
REFRIGERATOR WHIRLPOOL WRF736SDAM10 Unit leaking from water line at fill valve. Removed water line from fill valve and filter head. Replaced water line. Tested unit. All tests good.
Kevin M.
RESIDENTIAL REFR WHIRLPOOL WRX988SIBM00 Unit leaking when dispenser is used. I found water line at base of fill valve was leaking water when customer uses dispenser. I removed water at fill valve and filter head. Replaced water line. Tested unit. All tests good.
Kevin M.
DISHWASHER KITCHENAID KUDE70FXSS3 "OEM failure. Unit not draining. I put unit into diagnostic and found unit unable to drain. I removed front panel and tested drain relay on main control, voltage coming from relay. I went down to pump and had no voltage. I ohm checked pump motor and pump motor is good. I inspected wires and found that a wire popped out slightly at connector at pump due to wire harness not secure in holder and moving too much. I inserted wire properly into connector and secured wire harness properly. Tested unit again. All tests good."
Kevin M.
WASHER WHIRLPOOL WFW560CHW0 Customer said unit is not spinning. I put unit into diagnostic and found error codes for off balance loads. I tested unit with full load of clothes. All tests normal. Gave customer tips on loading and off balance loads.
Kevin M.
WASHER WHIRLPOOL WTW5000DW2 Unit not finishing spin cycle. I tested unit and found lid lock not engaging. I found voltage to lid lock but lid lock not engaging. Also found strike spring not working. Removed and replaced lid lock and strike. Tested unit. All tests good.
Patrick C.
DISHWASHER MAYTAG MDB4949SHZ0 Found the unit starting up on its own still. Checked errors same as last time. Needs new main control ; ordrng 1 W11225084 (cntrl-elec)
Kevin M.
WASHER MAYTAG MVWC565FW1 Customer stated the unit is not filling with cold water. I tested unit and found fill hoses are reversed. Instruct customer on reversed hoses. Also customer was concerned with lid not locking in wash cycle. I instructed customer lid will only lock when basket is spinning. All tests good.
Kevin M.
REFIRGERATOR WHIRLPOOL WRF736SDAM14 OEM failure. Unit leaking out freezer compartment. I found frozen over drain tube under unit. I removed drain and found foam from liner had broken off inside cabinet and clogged drain. I cleared drain and tested. All tests good.
Kevin M.
DRYER WHIRLPOOL WGD85HEFW0 Unit is giving check vent light. I tightened all vent connections inside dryer to prevent air loss. Made sure lint duct was sealed properly. I ran internal vent check in diagnostic mode. With vent on test fails. With vent off it passes. Dryer tests good.
Kevin M.
WASHER MAYTAG MVWB835DW4 Unit filling with water when unit is not in use. Found solenoid on fill valve seeping. Failed fill valve. Removed and replaced fill valve. Tested unit. All tests good.
Kenneth M.
DRYER ELECTROLUX EFMG627UTT0 Customer explained to me that unit would take a few dry cycles to fully dry. Tested unit and found all functions working properly. Informed customer that she needs to place larger loads into dryer for sensor to properly read load wetness or use a timer dry. Customer approves all functions.
Kenneth M.
DRYER MAYTAG MEDB765FW0 Foun dunit not turning on. Found unit with a bad thermal fuse. Removed and replaced and fixed kink in vent. Tested unit. Unit is now working properly. Customer approves function at this time. ; used 1 3390719 (THERMAL FUSE) from stock
Kenneth M.
REFRIGERATOR WHIRLPOOL WRS588FIHV00 Installed evap fan and harness. UI board and diffuser. Tested all functions of unit. Unit is now working properly. Customer approves function at this time.
Leon M.
REFRIGERATOR KITCHEN AID KRSF505ESS01 After running diagnostic check find that water tube and other lines inside of freezer door is moving and making a like dropping noise wiles opening and closing the door.; ordrng 1 LW10755680 (dor-fip) and 1 WPW10355585 (gasket-fip)
Kenneth M.
REFRIGERATOR WHIRLPOOL WRF767SDEM01 Installed ice maker and harness. Installed main board and UI. Tested all functions. Unit is now working properly. Customer appprves function at this time.
Kenneth M.
DISHWASHER MAYTAG MDB4949SDM2 Installed sump assem and tested unit. Unit is now working properly. Customer approves function. No leaks found.
Kenneth M.
REFRIGERATOR FRIGIDAIRE FGSS2335TF0 Customer concerned with the amount of ice unit is making. Informed customer that if she isn’t a big ice user to shut the ice maker off when ice bin is full. Customer approves function. Replaced ice maker and bin. All functions working properly.
Lance V.
ICE MACHINE KITCHENAID KUIC15NHZS0 "Needs repair, multiple issues.found compressor @ only 2amps, sealed system issue. Also, grid not heating fully below 10ohms tested. also, water not coming in evenly needs a dispenser as well. Requesting 2x labor for repair, need to re route with parts, allow 3.5hrs for repair.; ordrng 1 W10863947 (tube) and 1 W10919199 (grid-cuttr) and 1 WPW10200037 (drier-tube) and 1 WPW10218037 (evaporator) and 1 WPW10605286 (compressor)"
Kenneth M.
REFRIGERATOR GE CYE22USHBSS Installed water filter manifold. Unit is now working properly. Customer will call if problem continues. No water leak errror code at this time.
Lance V.
DISHWASHER WHIRLPOOL WDT710PAHW1 "Needs work-3 cup test failed, no water reaching top rack. found faulty sump assembly motor. Need to reroute with parts.; ordrng 1 W11085683 (pump&motor)"
Kenneth M.
REFRIGERATOR FRIGIDAIRE FFHT1814TW0 Found unit not cooling properly. Outside of unit is super hot. Found condensers fan not running. Found blockage keep condenser fan from running. Removed blockage and tested unit. Unit is now working properly. Customer approves functions at this time.
Lance V.
REFRIGERATOR WHIRLPOOL WRV986FDEM01 "Needs work- much ice buildup on refrigerator evaporator area, pool of water lower bottom. Issue within fan motor making unusual noises, as well as thermistor placement and drain defrost. Request customer to defrost unit prior to return visit. Need to reroute with parts.; ordrng 1 W11087438 (motor-evap) and 1 W11188493 (cover-evap)"
Kenneth M.
DISHWASHER WHIRLPOOL WDT730PAHZ0 Installed control board and UI and tested unit. Unit is now working properly. Customer approves function at this time.
Lance V.
REFRIGERATOR WHIRLPOOL WRS588FIHV00 "Needs work- major frost in evap area, evaporator fan not working, needs new thermistor as well as control inverter board for compressor, need to re route with parts ; ordrng 1 W11087200 (invrtr-box) and 1 W11170613 (harns-wire)"
Kenneth M.
DISHWASHER WHIRLPOOL WDT970SAHZ0 Installed console and control panel. Tested unit. Unit is now working properly. Customer approves function at ths time.
Kenneth M.
WASHER MAYTAG MVWB765FW3 Installed gearcase and tested unit. Unit is now working properly. Customer approves function at this time.
Lance V.
REFRIGERATOR WHIRLPOOL WRX735SDBM00 "Needs work- found faulty ice maker making buzzing noise, and not activating water valve, also the ice container motor receiver is worn out and the auger motor is unable to turn to dispense ice. We will need to re route with parts; ordrng 1 W11185686 (ice-contnr)"
Kenneth M.
FREEZER WHIRLPOOL WRX988SIBM01 Installed freezer door. Brackets. Wire harness and gasket. Tested unit. Unit is now working properly. Customer approves function at this time.
Jose H.
REFRIGERATOR WHIRLPOOL WRS325FDAB06 Installed parts check unit complete call
Jose H.
WASHER WHIRLPOOL WFC7500VW2 Apartment complex can could not collect need to talk to manager for payment 180
Jonathan C.
REFRIGERATOR WHIRLPOOL WRF540CWHZ01 P.o. 53332 tested unit has water and ice unit working to spec p.o. For service call
Jonathan C.
RANGE FRIGIDAIRE FGGF3036TFE Tested unit gas company said unit is leaking and not ingniting broiler tested see pic unit is working tested bake and broil and cooktop
Lance V.
WASHER WHIRLPOOL WTW4955HW0 "Needs work- found washer stainless basket faulty. Welds are coming loose on the seams, causing clothes to be ripped (sharp edges). Needs to order washer tub assembly, as well as to replace control board for svc pointer W11367903 white residue on clothing.; ordrng 1 W10910409 (basket)"
Jonathan C.
REFRIGERATOR MAYTAG MFW2055FRZ00 Installed Mullen strip tested working properly
Jonathan C.
REFRIGERATOR FRIGIDAIRE FFHT1814TW0 Found start dev bad replaced tested working to spec ; used 1 241941005 (START DEV) from stock
Kevin M.
RANGE WHIRLPOOL WFG320M0BS3 When customer plugged unit in and tried to run it started smoking from console. I removed console and found shorted main control. Main control is bad and will need to be replaced. All wiring is good. Ordering main control. Call customer at 951-241-3804 when I arrive. Give 30 min call ahead. ; ordrng 1 W11126814 (cntrl-elec)
Jonathan C.
RANGE WHIRLPOOL WFG515S0EB Found burner not lighting Replaced burner heads working to spec
Jonathan C.
REFRIGERATOR WHIRLPOOL WRF555SDFZ08 Tested unit found ice cube jammed tested working to spec
Kevin M.
M/W OTR WHIRLPOOL WMH31017HS2 Unit not heating and making a loud noise. I found magnetron making a louder than normal sound and slow cooking. Failed magnetron and diode. Ordering part. Allow 1 1/2 hours on return. I will have to pull down microwave. ; ordrng 1 W10754299 (magnetron) and 1 W10850446 (capactr-mg)
Jonathan C.
MICROWAVE WHIRLPOOL KMCS3022GSS transformer is bad This is a replacement
Jonathan C.
REFRIGERATOR FRIGIDAIRE FFHS2322MBMA Found hi code replaced thermistor in refer and freezer tested working to spec
Jonathan C.
DRYER MAYTAG MGDC465HW0 Found vent restriction in wall needs to be cleaned
Jonathan C.
WASHER MAYTAG MVWB835DW4 Found temp sensor on valve bad replaced tested working to spec
Jonathan C.
WASHER WHIRLPOOL WTW4816FW2 Found valves bad replaced tested working to spec
Jonathan C.
WASHER WHIRLPOOL WTW4950HW1 Found valve bad replaced tested working to spec ; used 1 W11038689 (VALVE) from stock
Jonathan C.
WASHER MAYTAG MVWC465HW2 Phone number for rent a center found latch bad replaced tested working to spec
Jonathan C.
REFRIGERATOR WHIRLPOOL WRS335FDDM01 Found gear stripped on ICEMAKER replaced tested working to spec
Jonathan C.
REFRIGERATOR WHIRLPOOL WRS325SDHZ01 Found pin bent unable to reinstall pin see pic metal bar bent
Jonathan C.
REFRIGERATOR FRIGIDAIRE LFSS2312TF0 Found ice cube jammed cleared working to spec
Jonathan C.
DRYER MAYTAG MEDC215EW Found belt bad replaced with kit tested working to spec
Jim S.
WASHER MAYTAG MVWB880BW0 "Replaced tub, lid, washplate, and suspension. Unit tested ok"
Kenneth M.
WASHER GE GTW460ASJ7WW Installed control board. Voltage going down to unit not turning on. Went to check drain and unit turned on. Found loose wire connection st drain. Unable to repair. Entire harness needs replacing. Ordering new wire harness. ; ordrng 1 WH19X25438 (harness main green)
Jesus C.
WASHER WHIRLPOOL WGT4027HW0 Customer states that unit is not sensing load. Checked unit and ran diagnostics no error codes found. Ran manual test and found the water valve not dispensing water properly. Pulled unit out and unplugged. Disconnect water valves uninstalled valve. Installed valve and assembled unit.Tested unit and it’s not working as design.
Jesus C.
REFRIGERATOR KITCHENAID KRFC302ESS00 Removed cover and installed new cover. Also I put Omer was having problems with freezer racks. Checked unit and found some ice holding tracks back. Removed racks and cleared ice. Assembled unit and tested. Unit is no working as design.
Jesus C.
WASHER WHIRLPOOL WFW85HEFW0 Customer states that unit doesn’t unlock after each cycle. Ran diagnostics and found error code. Per tech sheet checked all components and possible causes of error code. Inspected pressure hose and air trap. Checked drain pump and drain hose. Checked water valve all components are good. Unit is working as design. Customer paid for call. F8-E3. Overflow condition
Jose H.
REFRIGERATOR KITCHENAID KRFC704FPS01 Needs rails reschedule call; ordrng 1 W10866163 (glide) and 1 W10866166 (glide)
Jesus C.
DISHWASHER MAYTAG MDB8959SFZ4 Customer states that unit track broke. Checked unit and found the left side track weld split. Removed upper rack and pulled unit out. Remove both tracks and jntalled new tracks. Assembled unit and tested. Unit is now working as design
Jose H.
REFRIGERATOR JENN-AIR JFFCC72EFS00 New ice maker would not cycle need to order new one com0ete call; ordrng 1 W10908387 (icemaker)
Jesus C.
DRYER MAYTAG MDB4949SDM2 Customer states that unit is not draining. Checked unit and found water in unit. Ran diagnostics and found error codes. Drain pump not draining removed water and replaced pump. Ran diagnostics and passed. Unit is now working as design. F6-E4. Float switch open F8-E2. Drain motor electrical problem F8-E1 Slow drain
Jesus C.
DISHWASHER KITCHENAID KDPE234GPS0 Customer states that unit is not working. Checked unit and found the panel and control not responding. Removed front panel checked incoming voltage. Getting 118 vac to control. Replaced both the control and panel. Assembled unit and tested. Unit is now working as design.
Jose H.
WASHER WHIRLPOOL RTW4516FW0 Pump not working needs part ; ordrng 1 W11255272 (gearcase) and 1 WPW10661045 (drain pump)
Jesus C.
DRYER KITCHEN AID KGHS02RWH0 Customer states that unit is not heating. Checked unit and ran it. Removed Lower panel and unit burner does not stay on. Placed air flow meter and failed. Customer unit has a vent restriction. Advised customer to have vent system cleaned out. No repairs needed at this time. Customer paid for call
Jesus C.
REFRIGERATOR KITCHEN AID KSC24C8EYY02 Removed evaporator cover and pull the unit out. Disconnect power and removed that thermistor. Installed new thermistor and removed back cover. Replaced the water tubes and plug in the back in. Ran to Spencer and verify there’s no leaks and unit. Assembled unit and it’s now working as designed. Customer paid the remaining balance for labor per check number 8042
Jonathan C.
REFRIGERATOR WHIRLPOOL WRF757SDEM01 Found refer evap frozen over, would like to do the evap cover and harness one more time; ordrng 1 W11033168 (harns-wire) and 1 WPW10501260 (cover-evap)
Jesus C.
WASHER WHIRLPOOL WTW5000DW2 Customer states that the unit is not filling with water and shutting off. Ran diagnostics and found a couple error codes. Ran manual test and checked codes. Ran auto test and passed. Ran calibration test and advise customer to have unit balance. Found the right side feet lowered but unit is not leveled.manual test lock mechanism again and intermittently locks. Unplugged unit and removed UI and raised panel. Removed latch and installed new. Assembled unit and tested. Unit is no working as design. F8-E1. Long fill no fillF5-E4. Lid not open between cycleF5-E3. Lid unlock fault
Jonathan C.
REFRIGERATOR FRIGIDAIRE LGHD2369TF5 Found applesauce frozen on top shelf and veggie freezing in draw ICEMAKER still cycles when in off position needs ICEMAKER also dispenser dipping two drops after customer get water
Jesus C.
WINE COOLER WHIRLPOOL WUW35X24DS01 Pulled unit out and removed back panel. Recovered any refrigerant left on unit. Removed Dyer and service port. Installed new service port and dryer. Pulled vacuum and recharged unit. Unit is now working as design.
Jonathan C.
DRYER ELECTRIC MAYTAG MVWC425BW0 Found actuator code and lid lock code needs both; ordrng 1 WPW10006355 (actuator)
Jesus C.
DRYER MAYTAG MGD5500FW1 Customer states that unit is making loud noise. Checked unit and confirmed problem. Unplugged unit and disassembled unit. Removed wheels and installed new kit. Also found the tube burner vibrating and making noise. Tight screw and assembled unit. Ran unit and it no longer making noise. Unit is working as design
James M.
REFRIGERATOR KITCHENAID KRFF507ESS01 "Unit warm in fridge section 43 degrees. Ice build up on back wall.replaced fan, control board and control. Repositioned defrost thermistor per service pointer. Unit now functioning properly and customer approves."
James M.
WASHER WHIRLPOOL NTW4516FW Fund unit not spinning or agitating. Inspected unit and found mouse had got caught in belt and pulls causing belt to come off pully. Cleared blockage and reset belt. Retested unit and it is working as intended at this time.
James M.
WASHER MAYTAG MVWB865GW0 "Replaced main control and water inlet. Upon removing console, found hot water hose rusted out at connection to water. Hose connector came apart at inlet side. Informed customer of bad hose and they will replace with new. Installed new components. Unit is working as intended besides inlet hose."
James M.
MICROWAVE WHIRLPOOL WOC75EC7HS00 Installed new name plate and customer approves.
James M.
REFRIGERATOR WHIRLPOOL RJRS4280B Found unit with minor gapping in freezer door. Heated gasket to reset seal. Unit is sealed and operating as intended. Customer approves at this time.
James M.
REFIRGERATOR WHIRLPOOL KRFC302ESS Replaced ice maker and valve. After install unit filled ice maker and no leaks. Unit now working as intended and customer approves.
Jonathan C.
WASHER WHIRLPOOL WFW7590FW0 Unit has f3e1vode needs pressure switch and hose; ordrng 1 W11044558 (hose) and 1 WPW10448876 (switch-wl)
James M.
REFRIGERATOR FRIGIDAIRE LFHD2251TF Inspected fridge and found items blocking air flow and items stored next to ice maker freezing. Informed customer of how airflow world rise in fridge and not to store items directly blocking airways. Checked door sealing and found small gaps in gasket. Heated and reset gasket. Gasket now holding seal. Also found water line not hooked to house line due to no shut off valve on water line. Customer informed of need for plumber to fix water valve from wall as it has signs of leaking before hooking up water line to fridge.
James M.
WASHER MAYTAG MVWB766FW0 Replaced gear casing and washer. Reassembled unit and tested. Unit now working as intended and customer approves.
James M.
DRYER MAYTAG MGDX655DW2 "Found unity hooked from gas, power, and venting with broken belt. Installed dryer repair kit from truck stock 4392067. reassembled and tested unit and unit now functioning as intended. ; used 1 4392067 (DRYER REPAIR KIT) from stock"
James G.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 Replaced fill valve and fill tube Tested ok
James G.
REFRIGERATOR FRIGIDAIRE FFSS2615TS0 Installed lower camTested ok
Jim S.
RANGE WHIRLPOOL WFG540H0ES1 No power out of the control board. Open coil on gas valve; ordrng 1 W10919226 (regulator) and 1 WPW10349742 (cntrl-elec)
James G.
REFRIGERATOR U-LINE U-C01224FS-OOB "Tech line says air leaking somewhere, removed back and sealed around fill tube Tested ok"
Jim S.
WASHER SPEEDQUEEN AWN632SP116TW01 Need pressure switch and harness
James G.
OVEN KITCHENAID KODC304ESS01 Unit has has l-1 and neutral reversed. Unit has connection from pig tail that is not in junction box and not to code so we were unable to correct wiring issue.
Jim S.
REFRIGERATOR WHIRLPOOL WRX988SIBM00 The unit is shutting itself off and then restarting hours later. This is caused by a dc circuit failing. Will need to order boards and dc circuit motor.; ordrng 1 W10633627 (motor-evap) and 1 W10789392 (cntrl-elec) and 1 W10807590 (cntrl-elec) and 1 W11032800 (motor-evap)
James G.
WASHER WHIRLPOOL WFW75HEFW0 Replaced door lock and pressure sensor Ran service testTested ok
Jesus C.
REFRIGERATOR WHIRLPOOL KSSS42MBX01 "Customer states that unit is not cooling. Checked unit and found the evaporator fan not working. Removed rack and cover. Checked fan voltage and getting 118 vac; ordrng 1 WP4389155 (motor-evap)"
James G.
WASHER WHIRLPOOL MVWB765FW2 F2/E1 Cleared stuck key code and ran calibration cycle without any failure Tested ok
James G.
DISHWASHER WHIRLPOOL WDT720PADM2 Removed glass from drain pump Tested ok
Jesus C.
DRYER AMANA NGD4655EW0 "Customer states that unit is not working. Checked unit and found the motor humming. Unplugged and disassembled unit. Jumpered switch and plugged in unit. Press start button and motor not turning. Checked voltage on wires blue and white, getting 118 vac when start button is pressed. Ordering parts. ; ordrng 1 279827 (motordryer) and 1 4392067 (dryer repair kit) and 1 WP694089 (wheel)"
James G.
WASHER MAYTAG MVWB765FW1 "Removed rotor, stator and tightened gearcase mounting screws, reinstalled stator and rotor and retested several times.Tested ok"
Isidore A.
WASHER WHIRLPOOL WFW97HEXW2 "David Sr 7725396318Found over suds only coming out of vent in clean cycle , Advised customers washer needs to get rid of left over suds from previous washes. Per tech support recommended to try using about 2table spoons of salt to break down suds. I instructed customer put in 2 tbls salt in clean cycle."
Isidore A.
REFRIGERATOR KITCHENAID KBFN506EPA00 Top left door hinge screw coming off hitting top panel. Removed top panel refastened hinge to customer satisfaction. Test door ok at this time.
Jesus C.
DRYER - GAS WHIRLPOOL WGD6620HC0 Customer states that the unit is making loud noise. Checked unit and found that the unit is rattling excessively. Unplug the unit remove the top panel and front panel. Disassemble unit and verified any loose parts. What I found is that the blower wheel is cracked and needs to be replaced. Ordering parts.; ordrng 1 WP697772 (blower wheel)
Isidore A.
WASHER WHIRLPOOL WGT4027HW0 "Removed dryer, old washer lid latch and installed new lid latch. Reinstalled washer top and dryer. Test washer latch for codes and operation,ok at this time, working as designed."
Isidore A.
DRYER MAYTAG MGDB765FC0 "Verified dryer not heating. Removed bottom panel found dryer igniter open cracked, installed new igniter, test ok ignition on heating but short cycle found vent inside too long kinked/ crushed. Cut and corrected for testing. Dryer working at this time.See Note"
Jesus C.
DISHWASHER IKEA IUD8500BX1 Customer states that the unit doesn’t shut off. Checked unit and the user interface working intermittently. Remove fan panel and visually inspected the control on the UI.. Assembled unit and need to order a new UI and new to order new UI. ; ordrng 1 W11105144 (panel-cntl)
Isidore A.
REFRIGERATOR WHIRLPOOL WRS315SDHW01 Seal refrigerator cabinet edges with silicone adhesive W10841140. Advised customer to let silicone set and not to open doors too often.
Jesus C.
WASHER WHIRLPOOL WFW5620HW0 Customer states that unit is not turning on. Checked unit and found the UI panel not working. Pulled unit out and removed top panel. Disconnect UI and checked power getting 12 vdc. Connected UI and display started to work. Ran diagnostics and got error code. per service pointer order Acu.F0-E2. Oversuds ; ordrng 1 W11319991 (cntrl-elec) and 1 W11322903 (cntrl-elec)
Isidore A.
WASHER WHIRLPOOL WFW96HEAC0 "Found washer over suds explained has detergent that is 8* concentrated. Needs to use half the amount, advised on cleaning washer to rid left over detergent."
Isidore A.
DRYER MAYTAG MGD4200BW1
Isidore A.
RESIDENTIAL REFR KITCHENAID KRFC704FPS00 Test refrigerator ok at this time icemaker working at this time
Irvin F.
DRYER CROSLEY VGD6505GW0 "Cx says the dryer will not turn on. Confirmed dead. Checked door switch unplugged. Connected door switch, dryer is not operating. No heat in the unit. Removed front panel found main coils not plugged into harness. Connected to harness, bypassed the door switch. All ops working. Assembled unit test good powers, runs and heats. All ops normal"
Irvin F.
REFRIG/SIDE-BY-S WHIRLPOOL WRS325FDAM02 "Removed failed lights and filter house. Installed replacement components. Test for operation, passed. Got air out the lines. Done."
Irvin F.
REFRIGERATOR WHIRLPOOL WRX735SDHZ00 "Cx says ice maker is not cycling. The IM is stuck mid harvest, won’t complete. Removed failed IM. INSTALLED replacement. CYCLED. DONE."
James M.
RANGE FRIGIDAIRE FFEF3016TW "Customer reinstalled unit. Inspected unit and found remaining terminal blocks now blown out. Rear right burner has missing center cap. Also found grounding screw missing. Will return 7-25 to install. ; ordrng 1 316001003 (screw) and 1 316442301 (element,lg) and 1 318372211 (element-surface) and 2 5304521730 (TERMINAL BLOCK KIT)s"
Irvin F.
DRYER WHIRLPOOL WED5000DW2 "CX SAYS THE DRYER IS DEAD. CONFIRMED. CHECKING UNIT FOUND THE HI LIMIT TRIPPED. REPLACED PART. TEST FOR OPERATION, PASSED. DONE."
Hector Z.
WASHER MAYTAG MVWX655DW1 Customer cancel at the door.
Hector Z.
WASHER WHIRLPOOL WFW87HEDW0 Replaced: Drawer dispenser (W10575334). Tested ok.
Francisco S.
REFRIGERATOR KITCHEN AID KRSC503ESS "Checked unit found unit cooling. Cx stated it started cooling this morning. He also stated he had condensation. Tested thermistors/fans/ also ran test 4 and got a good frost pattern on ffc evap. Found thermistor in ffc not upgraded to optimal position. Relocated thermistor, zip tied it to evap and added aluminum tape.
Francisco S.
WASHER WHIRLPOOL MVWC565FW1 "Removed and replaced door latch, tested ops unit working as intended."
Francisco S.
M/W OTR WHIRLPOOL WML55011HS2 Checked unit found missing mounting nut. Removed wrapper inserted new nut re assembled unit. It is now ok.
Francisco S.
REFRIGERATOR WHIRLPOOL WRS331SDHM00 Removed and replaced filter/purged air out of line.tested ops it is working as intended.
Francisco S.
REFRIGERATOR WHIRLPOOL WRS331SDHM00 Removed and replaced filter/purged air out of line.tested ops it is working as intended.
Francisco S.
RANGE - GAS WHIRLPOOL WFG505M0BS3 Checked unit control or clock not coming on. Checked power and polarity at outlet checked ok. Found loose connection at power plug. Re did connection and tested ops unit now working as intended.
James G.
REFRIGERATOR WHIRLPOOL WRF989SDAM01 paddle install Compressor and evaporator are to be under s71233; ordrng 1 W10276644 (compressor) and 1 W10687098 (evaporator) and 1 W11028219 (pad)
Ethan S.
REFRIGERATOR FRIGIDAIRE LGHB2869TF Customer stated icemaker was not working pool icemaker found the icemaker to have a complete fool being of eyes tested icemaker ice maker seem to be functioning and sign
James G.
REFRIGERATOR KITCHEN AID KRFF507EWH01 Needs regulator Approved ; ordrng 1 8212547RP (tube-water) and 1 W10786952 (valve)
James G.
DISHWASHER KITCHEN AID KDTM704ESS0 Dispenser door broken ; rqstng P&A on 1 W10861000 (detergent dispenser)
Erick S.
WASHER AMANA NTW4516FW3 "Cycled unit and found it with controller error causing failure, ran diagnostics and found control not advancing. Replaced control , re ran test and it passed all tests with no errors. Job complete"
Erick S.
REFRIGERATOR FRIGIDAIRE FFSS2615TD Found unit with failing the risotto causing uniit not to cool properly. Replaced sensor. Also door not closing properly. Removed door and hinge. Retested and door is proeprly sealing wpl the way around. I is now cooling with no errors. Job complete; used 1 242278801 (SENSOR) from stock
Ethan S.
WASHER WHIRLPOOL MVWC565FW1 Replaced parts tested unit unit checked good job complete
Ethan S.
RESIDENTIAL REFR KITCHEN AID KRFF707ESS Replaced parts tested unit unit checked good job complete
Erick S.
DRYER WHIRLPOOL WED4815EW1 Cycled unt and found it failing due to ripped belt causing it not to turn. Replaced belt . Door also hard to close. Replace Retested it and u it passed all tests with no errors. Job complete; used 1 4392067 (DRYER REPAIR KIT) from stock
Erick S.
REFRIGERATOR GE GEF16THMRWW Cycled unt and found fan blade cracked causing not circulate proper airflow. Replaced fan bales. Realigned secured door gasket.Reformed gasket with heatgun to ensure proper seal around door. Unit is cooling with no errors. Job complete ; used 1 WR60X10204 (FAN BLADE) from stock
Isidore A.
RESIDENTIAL REFR KITCHENAID KRFC704FPS00
Erick S.
DRYER WHIRLPOOL WGD4850HW0 "Cycled unit and found it making noise due t9 bad roller . R placed with new roller kit, retested it and it passed all tests with no noise or errors. Job complete"
Enrique R.
REFRIGERATOR WHIRLPOOL KUIX305ESS2 Customer canceled service . Ice maker is working .
Enrique R.
DRYER MAYTAG MEDX655DW1 Maytag dryer won’t stop drying cycle . Shorted timer installed new timer . All functions checked normal .
Isidore A.
DISHWASHER KITCHENAID KDTE254ESS1 "Customer states dishwasher maker strange noise(beeping), user interface W10902370, dishwasher has no codes,@ test heater ok a approximately 7 amp draw. No problems found other than beeping. Part ordered ; ordrng 1 W10902370 (panel-cntl)"
Enrique R.
DRIYER MAYTAG MEDC465HW0 "Installed drive motor , wheel and timer . All functions checked normal"
Enrique R.
DISHWASHER JENN-AIR JDB9000CWS3 Jenn-aire dishwasher . Found broken tracks. Installed new tracks . All functions checked normal . No leaks .
Enrique R.
REFRIGERATOR WHIRPOOL WRT518SZFM00 Found both compartments not cooling . Shorted start device . Installed devise . Compressor kicked on . All functions checked normal .
Enrique R.
REFRIGERATOR FRIGIDAIRE FFTR1821TB4 "Frigidaire refrigerator RC not cooling . Found air vent obstructed with ice . Installed new defrost timer , removed frost . All functions checked normal at time of service . No leaks ."
Irvin F.
DISHWASHER WHIRLPOOL WDF330PAHS3 Installed sump and control. The motor is not running. The contact on the motor is faulty. The new control is nit seeing any errors. Motor is not running; ordrng 1 W10837401 (pump&motor) and 1 W11242945 (harns-wire)
Darren A.
WASHER GE GTW460ASJ8WW "Removed an obstruction between tub and basket,cycle tested,checks out good."
Darren A.
WASHER WHIRLPOOL WTW4816FW2 "Replaced faulty water valve, recalibrated unit,cycle tested, checks out good."
Irvin F.
WASHER MAYTAG MVWC565FW1 Cx says the washer will not drain. Unplugged on arrival. Plugged in the pump not moving water. Removed all water installed new pump. Calibration failed the gearcase is abs wash plate worn hub not spinning and shifter not shifting. Replacing components. Gearcase shifter cam hub wash plate. ; used 1 W10876600 (PUMP-WATER) from stock
Darren A.
RESIDENTIAL REFR WHIRLPOOL WRS325FDAM04 Replaced lights and door seal. Checks out good.
Irvin F.
WASHER WHIRLPOOL WTW5000DW0 "This unit is severely in disrepair. The wash plate hub rusted to the gearcase shaft. The tub is full of debri, standing water in tub WILL NOT DRAIN FROM THE TUB WITH HOSE REMOVED. (repairing outside) The unit will needs excessive parts and labor to repair. Once able to test the unit could have other issues. SHOULD NOT REPAIR THIS UNITPUT UP FOR REVIEW. SHOULD BUY OUT CONTRACT. ; ordrng 1 W10528947 (drive hub kit) and 1 W10721967 (drive pulley) and 1 W10752719 (basket) and 1 W10913953 (actuator) and 1 W11035751 (gearcase)"
Irvin F.
M/W OTR WHIRLPOOL WMH31017HW2 The table is cracked the actuator is grinding. Replacing the glass and turner. ; ordrng 1 W11252182 (ring-turn) and 1 W11367904 (TABLE)
Darren A.
WASHER MAYTAG MVWX655DW1 "Found unit stuck in sensing mode, unplugged and cleared codes, recalibrated washer and cycle tested, checks out good."
Darren A.
REFRIGERATOR MAYTAG MRT711SMFZ00 "Reinstalled ice maker bail arm, ice maker cycled okay, checks out good."
Danny G.
REFRIGERATOR WHIRLPOOL WRF560SEHZ00 Water is leaking Found faulty water valve Replaced and install new water valve Reinstall unit and found no water leaks Turn water supply on and test dispenser and no water leaking Unit is working properly
Danny G.
DRYER MAYTAG MGDB835DW4 Duct had melted with plastic and discoloring clothesReplaced duct air Reinstall dryer Unit is heating and cycling properly
Danny G.
REFRIGERATOR WHIRLPOOL KRFF707ESS01 Unit is not cooling properly Per techline supportUsed adhesive to seal the frameUsed steam gun to defrost evap Replaced and install new sensor and air tower and cover evap Program unit to defrost every 8hrs Reinstall unit Advised client to allow 24hrs for unit to reach proper temp
Dane K.
DISHWASHER MAYTAG MDB4949SHZ0 Upon arrival the unit was not washing the dishes properly. Found the water valve not opening properly. Removed and replaced water valve and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR WHIRLPOOL WRF555SDHV01 Upon arrival the unit was not making ice. Found the icemaker was getting 120 but would not cycle with John. Removed and replaced ice maker and tested unit. Unit functions normal now
Dane K.
REFRIGERATOR KITCHEN AID KFCS22EVMS8 Upon arrival the unit was leaking. Found unit leaking from the freezer due to a frozen drain tube. Removed old grommet and drain assembly and replaced with new drain tube. Defrosted frozen drain pan and tube. Unit functions normal now; used 1 W10619951 (TUBE DRAIN) from stock
Ethan S.
RANGE WHIRLPOOL WFG525S0HS1 Customer stated that the unit burner head was not functioning tested burner had found it not to be operating as designed needing to re-order burner head; ordrng 1 WPW10515454 (burnr-head) and 1 WPW10515455 (burnr-head)
Dane K.
REFRIGERATOR WHIRLPOOL WRX735SDHZ02 Upon arrival the unit was not making ice. Found icemaker would not cycle and jumped. Removed and replaced ice maker and tested unit. Unit functions normal now
Dane K.
DRYER WHIRLPOOL DRYER NOT READABLE Upon arrival the unit would not start it would only buzz.Found a rag in the blower wheel seizing up the motor. Removed rag and tested unit. Unit functions normal now
Dane K.
WASHER WHIRLPOOL ATW4675YQ1 Removed and replaced actuator and tested unit. Unit functions normal now
Cruz B.
DRYER WHIRLPOOL WED4815EW1 "Fixed for FTC- unit not turning on, cK voltage at terminal block found 240 AC, removed back cover and tested thermal fuse and found it to be bad, use thermal fuse from SP, unit is working as designed and is heating fine as well, cx ok repair. ; used 1 WP3392519 (THERMAL FUSE) from stock"
Cruz B.
REFRIGERATOR WHIRLPOOL GI5SVAXVL00 "COD unit OOW- found unit not cooling in both sections, pulled unit out and removed unit cover, tested start relay and found it to be good, tested compressor windings and found resistance to be high, compressor is clicking off like it’s trying to start. Informed cx that compressor need to be replaced, cx then said they will purchase a newer one. Cx paid for service call ($115.00) with card. Send cx a receipt via mail."
Erick S.
WASHER MAYTAG MVWB855DC "Cycled unt and found unit with stripped wash plate causing it to make noise,metal shavings coming off causing black in clothes. Unt will need new wasplate; ordrng 1 W10902814 (washplate)"
Cruz B.
REFRIGERATOR WHIRLPOOL MFI2067AES "Fixed - installed all new parts (ice maker, valve), water filled mold, found no over flow, cooling and temps are working as designed, cx ok repair."
Erick S.
DISHWASHER KITCHENAID KUDS03CTBL2 Cycled unit and found unit with bad door dispenser and broke spring causing door to slam. Unit will need new spring and drispsner replaced; ordrng 1 WP8270020 (door spring) and 1 WPW10199696 (dispenser)
Chris M.
OVEN JENN-AIR JJW2430DS03 Customers issue was receiving error code when using Meet probe.I entered oven into diagnostics cleared error code.After troubleshooting in talking with customer found the issue was with meat probe itself. I Put oven in a preheat to 350°. Calibrated temperature. All functions tested good with the use of the probe in also and just regular bake mode. Job complete
Chris M.
DISHWASHER WHIRLPOOL WDF330PAHS2 Customers issue is that the plastic stoppers on the top rail we’re coming off. Resecured him back on to railing. All functions tested good. Job complete
Chris M.
RANGE WHIRLPOOL WFG525S0HS1 Customers issues left front burner was not working. Found igniter to be bad. Replaced burner had tested for proper function on all burners everything is functioning as designed. Job complete
Enrique R.
FREEZER WHIRLPOOL WRX988SIBM01 "Installed freezer door , central electric , module . Also need RC door gaskets . Customer forgot to mention on my first visit .; ordrng 2 W10846057 (gasket-fip)s"