Service History 296 - Appliance Repair Specialists

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Los Angeles, California 91356

Oscar

Job Details: 03/24/2025

"As all pre diagnosed parts and components were replaced, a successful functional testing was achieved."

We serviced a

MAYTAG WASHER

Model MVWB835DW5

Near Azusa, California 91702

Jaime

Job Details: 03/24/2025

"Installed a new suspension, clutch,& Transmission"

We serviced a

MAYTAG WASHER

Model MVW7230HW1

Near Bakersfield, California 93314

Aaron

Job Details: 03/24/2025

"Checked the unit the washer in spin was chattering , looked underneath missing rotor bolt , pulled rotor. Slider ok , used slider kit to replace missing part , installed bolt , tested operations ok now at this time"

We serviced a

MAYTAG WASHER

Model MVWB865GW0

Near Los Angeles, California 91326

Giovanni M

Job Details: 03/24/2025

Replaced the lid and hinges. Tested unit after to make sure it locks. Everything is working as designed at this time.

We serviced a

MAYTAG DRYER

Model MGD4500MW1

Near Delano, California 93215

Esteban

Job Details: 03/24/2025

"Motor, blower, rollers, pulley and belt were removed and replaced. Unit passed all test. Unit is working as intended."

We serviced a

MAYTAG WASHERHER

Model MVW6230HW3

Near Palmdale, California 93551

Samson

Job Details: 03/24/2025

"Found unit out of balance due to the rear leg being crooked, straightened it and balance unit. Unit sitting on drainage plastic which makes leveling difficult. Complete"

We serviced a

WHIRLPOOL RANGE

Model WFG525S0JZ1

Near Tehachapi, California 93561

Ian Y

Job Details: 03/24/2025

"Customer was complaining bake would only start intermittently. Remove and replaced units spark module/dsi board. Tested, unit started up in bake 5 times in a row. Job complete."

We serviced a

MAYTAG DRYER

Model MGDB835DW4

Near Bakersfield, California 93309

Felipe S

Job Details: 03/24/2025

Install the new blower and motor on the unit. Retest and now is working properly. Job complete

We serviced a

FRIGIDAIRE FREEZER

Model FPFU19F8WF7

Near Camarillo, California 93010

Isidro

Job Details: 03/24/2025

"Minor frost chunk accumulating on evaporator drip drain pan middle area, I adjusted the drip pans edges inwards to catch water better when defrosting, unit is now draining properly as designed at this time of service"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRFF3236RB00

Near Bakersfield, California 93312

Felipe S

Job Details: 03/24/2025

Upon arrival found unit with ice maker arm stuck in the ice bin when the drawer was on close position. This was causing the ice maker think the ice bin was full. Readjust the ice bin on the right position. Retest the unit and now ice maker starts production. Job complete

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW3

Near Lindsay, California 93247

J.E.

Job Details: 03/24/2025

"Cycled unit and found faulty actuator causing damage to belt and cam. Installed new actuator, cam and belt retested unit now working as designed job completed ; used 1 W11239857 (Belt), 1 W1148722 (Actuator), and 1 W10721967 (Cam) from stock"

We serviced a

WHIRLPOOL RANGE

Model WFG745H0FS0

Near Moreno Valley, California 92553

Kevin

Job Details: 03/24/2025

Unit not lighting in middle burner. I found loose wire on ignitor and ignitor was not sparking. I attached wire and tested. All tests good.

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ3

Near Castaic, California 91384

Felipe S

Job Details: 03/24/2025

"Upon arrival found unit with error code F8E2, this about the inlet valve electrical problem. Erase the code and run test cycle, pump is having a noise when is running, but no water is present at the spray arms, only in the bottom of the unit. This unit has a bad pump assembly. Replace the pump, retest the unit and now is working properly. Job complete"

We serviced a

MAYTAG WASHER

Model MVW7230HW1

Near Planada, California 95365

Manuel B

Job Details: 03/24/2025

Washer drain pump is working good on site. Customer said not draining All cycles pass.

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW3

Near Nipomo, California 93444

Leo

Job Details: 03/24/2025

"Ran diagnostics program, no error codes, looked under unit, belt has nice tension and taught, no signs of oil leakage, back panel is firmly secured to cabinet as shown in service pointer, CX described overloading unit and calibrated unit to maker specs and passed, ran a quick wash cycle to test unit and it ran properly, Job complete."

We serviced a

MAYTAG WASHER

Model MVW6500MBK0

Near Clovis, California 93619

Timothy

Job Details: 03/24/2025

"Checked for faults and found a 0-3 (overload), 7-1( tach missing/wrong sig NAl), 2-3(acu/ui mismatch). In the service cycle the tub did not disconnect for the agitation portion. Looked under unit and found the actuator and clutch were not attached. Removed both components, inspected and reinstalled them . Ran a service test and found the unit completed the cycle . Calibrated unit. Unit operating as designed."

We serviced a

WHIRLPOOL WASHER

Model WTW8127LW0

Near Tulare, California 93274

J.E.

Job Details: 03/24/2025

Cycled unit and found fratricidal dispenser out opposition made adjustments to fabric dispenser and retested unit no Longer leaking. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Santa Clarita, California 91355

Felipe S

Job Details: 03/24/2025

"Upon arrival found unit with error code F9E1, this about no drain. Check the unit and is no water and pump still running. Blow air to the hose, and check the pressure hose, alls seems to be good. This unit still having the problem. Replace the control board on the unit. Retest the unit and now is working properly. Job complete"

We serviced a

WHIRLPOOL WASHER

Model WTW5100HW3

Near Merced, California 95348

Cruz

Job Details: 03/24/2025

Fixed-used part from stock (w11395618 capacitor) found f7e1 capacitor failure- unit will not start a cycle due to a capacitor- removed bad one and then installed new (capacitor) capacitor test pass- auto test pass- no leaks- no errors- cx ok repair ; used 1 W11395618 (Capacitor) from stock

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Thousand Oaks, California 91360

Giovanni M

Job Details: 03/24/2025

"Unit was getting a F7E1 error code. I replaced the actuator and capacitor from truck stock to repair the unit. Ran a diagnostic cycle after and the unit is working as designed at this time. ; used 1 W11481722 ( Actuator), and 1 W11395618 (Capacitor) from stock"

We serviced a

WHIRLPOOL WASHER

Model WTW6157PB0

Near Lindsay, California 93247

J.E.

Job Details: 03/24/2025

Cycled unit and found unit not shifting properly causing of balance. Found bad connection to shifter. Secured shifter connection and retested unit now working as designed job completed

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Merced, California 95348

Cruz

Job Details: 03/24/2025

Fixed- used part from stock (w10913953 actuator) found f5e7 actuator failure- unit is not agitating due to bad actuator- removed bad one and then installed new (actuator) calibration test pass- auto test pass- no leaks- no error- cx ok repair ; used 1 W10913953 (Actuator) from stock

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW1

Near Los Angeles, California 91364

Giovanni M

Job Details: 03/24/2025

Unit is getting a F0E9 error code. Cleared the error code and ran a diagnostic test cycle and everything came back good. Found a problem with one of the springs. I uninstalled and then reinstalled properly. Everything is working as designed at this time.

We serviced a

MAYTAG DRYER

Model MGDC465HW0

Near Ontario, California 91764

Jaime

Job Details: 03/24/2025

Had a limit thermostat kit installed; used 1 W11050897 (Cut off kit) from stock

We serviced a

MAYTAG DRYER

Model MED7230HW2

Near Turlock, California 95380

Cruz

Job Details: 03/24/2025

"Fixed- used part from stock (4392067 dryer kit) found rollers to be kocking during all cycles- removed bad ones and then installed new (dryer repair kit) tested unit, no knocking sound, good air flow, heating as designed- cx ok repair ; used 1 4392067 (Dryer repair kit) from stock"

We serviced a

WHIRLPOOL DRYER

Model WGD4950HW2

Near Los Angeles, California 91367

Giovanni M

Job Details: 03/24/2025

CX said the unit wasnt drying properly. Upon diagnosis I found the duct to be kinked. I uninstalled unit and then reinstalled so the duct wasnt kinked.

We serviced a

WHIRLPOOL DRYER

Model WED6150PB0

Near Lindsay, California 93247

J.E.

Job Details: 03/24/2025

Cycled unit and found loose screws on door causing alignment issue on door catch. Tightened and secured door screws retested unit door now closing as designed. Job completed

We serviced a

WHIRLPOOL ELECTRIC DRYER

Model n/a

Near Merced, California 95340

Cruz

Job Details: 03/24/2025

"Fixed- cx states lights will flash and unit will not start- found loose wire at panel ui, reseated, then tested all lights are now working and unit is starting- cx ok repair"

We serviced a

MAYTAG DRYER

Model MGD6230HW0

Near Palmdale, California 93551

Samson

Job Details: 03/24/2025

"Cx complain about dryer making a rattling noise, found unit robbing against the round metal object behind unit(picture attached). Reposition unit and reinstalled vent. Unit test ok. Complete"

We serviced a

MAYTAG WASHER

Model MVW6200KW2

Near Los Angeles, California 91306

Sean W

Job Details: 03/22/2025

"Entered diagnostic mode and noted all error codes displayed as instructed by cx and whirlpool, making call a pseudo to send to techline on Monday Ui displaying F8E1,F9E1,and F3E2; schdld next appmnt for 3/24 MON !"

We serviced a

MAYTAG RANGE

Model MGS8800FZ0

Near Los Angeles, California 91307

Sean W

Job Details: 03/22/2025

"External problem cashing control issues,need to call techline.; schdld next appmnt for 3/24 MON !"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325FDAW04

Near Los Angeles, California 91304

Sean W

Job Details: 03/22/2025

"Led flickering, door switch loose and harness not making good contact,ordered new switch,led module and harness.; ordrng 1 WPW10515058 (Led module) and 1 WP2149705 (Switch) and 1 W10667067 (Harness)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KSSC42QTS02

Near Simi Valley, California 93065

Sean W

Job Details: 03/22/2025

"Controls getting power but,Control box blinking and Ui on freezer door is flickering and going blank when you turn u it on and off,compressor not energized but has correct resistance between common run and start,and system not cooling,control box and freezer door Ui.; ordrng 1 WPW10468940 (Control box) and 1 WPW10151236 (Freezer door Ui)"

We serviced a

MAYTAG LAUNDRY

Model MVW4505MW2

Near Simi Valley, California 93065

Sean W

Job Details: 03/22/2025

"Ui displaying F8E1,and F0E9 and noticed water filling slower than designed,ordered new water valve.; ordrng 1 W11513255 (Water inlet)"

We serviced a

AMANA DRYER

Model NGD4655EW4

Near Turlock, California 95380

Cruz

Job Details: 03/22/2025

Need work- found igniter to be open causing unit not to heat- will need to order part- ; ordrng 1 279311 (Igniter)

We serviced a

GENERAL ELECTRIC DRYER - ELECTRIC

Model GTD48GASW0WB

Near Atascadero, California 93422

Leo

Job Details: 03/22/2025

"Fuse control or timer having a bad connection may cause issue, ordering thermal control switches and timer Ordering : WE04X25199 SAFETY THERMOSTAT, WE04X25201 INLET THERMOSTAT, WE04X25195 OUTLET THERMOSTAT, WE04X26138 HIGH LIMIT THERMOSTAT, WE4X448 DETECTOR ASM FLAME DETECTOR, WE04X24550 TIMER.; ordrng 1 WE04X24550 (TIMER) and 1 WE04X25199 (SAFETY THERMOSTAT) and 1 WE04X25201 (INLET THERMOSTAT) and 1 WE04X25195 (OUTLET THERMOSTAT) and 1 WE04X26138 (HIGH LIMIT THERMOSTAT) and 1 WE4X448 (FLAME DETECTOR ASM)"

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model PYE22KYNKFS

Near Paso Robles, California 93446

Leo

Job Details: 03/22/2025

"Main board,Evaporator fan thermistor,Im door, 2- tubes RTV food grade Silicone2 job count ,Evap assembly kit,Ordering following parts:WR55X10025 SENSOR TEMP WR17X37708 Evaporator fan box assembly, WR78X26087 Icebox door assembly WR55X46808 MAIN CONTROL BOARD2- RTV102 Silicone adhesive tubes.; ordrng 1 WR78X26087 (ICEBOX DOOR ASM) and 1 WR17X37708 (Evaporator fanbox) and 1 WR55X46808 (MAIN CONTROL BOARD) and 2 RTV102 (Silicone adhesive)s and 1 WR55X10025 (SENSOR TEMP FF)"

We serviced a

WHIRLPOOL WASHER

Model WTW5105HW3

Near Perris, California 92570

Kevin

Job Details: 03/22/2025

Unit agitating when told to spin and spinning when told to agitate. I reset and calibrated in diagnostic and it worked in diagnostic. When in normal cycle it goes back to being backwards. Removed and replaced cam to see if it was getting stuck. Not getting stuck. Ordering actuator and main control. ; ordrng 1 W11621183 (Cntrl elec) and 1 W11481722 (Actuator)

We serviced a

MAYTAG WASHER

Model MVW6200KW0

Near Burbank, California 91506

Oscar

Job Details: 03/22/2025

"Visual and physical inspection leaded me to a randomly working UI panel. (Unable to access diagnostics).And when tried functions testing, there no power going to drain pump, and lid lock activation either.Recommending tagged parts plus some of previously ided parts.; ordrng 1 W11406492 (UI panel) and 1 W11419692 (Control unit) and 1 W11263349 (Drain pump) and 1 W11032875 (Lid lock)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ08

Near Glendale, California 91202

Oscar

Job Details: 03/22/2025

"Visual and physical inspection showed a randomly working UI, an ice maker that doesnt stop making ice, and a diffuser that is stuck in open. Replacing Ice maker, diffuser, UI, and broken bin recommended.; ordrng 1 W11359448 (Ice maker) and 1 W11456119 (UI panel) and 1 W11204060 (Diffuser) and 1 W10900538 (FF bin)"

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near Altadena, California 91001

Oscar

Job Details: 03/22/2025

"Visual and physical inspection leads to a gone into perpetual drain humming because the impeller is not moving, and to very erratically working UI panel. Tagged parts are recommended for replacing.; ordrng 1 W11646706 (UI panel) and 1 W11578827 (Controller) and 1 W10775446 (Drain pump)"

We serviced a

WHIRLPOOL DISHWASHER

Model PSEUDO

Near La Crescenta-Montrose, California 91020

Oscar

Job Details: 03/22/2025

"Because of the lack of answering the door, I called customer and she said that she had canceled for today, and that shell reschedule After.; O-emld tckt"

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Perris, California 92570

Kevin

Job Details: 03/22/2025

"Unit not powering on. I found voltage to main control but not powering on. Failed main control. The rotor bolt had fallen out before it stopped. Ordering rotor, slider and clutch in case of short. Door locked. Will get pic of mod on return. ; ordrng 1 W10754448 (clutch) and 1 W10734521 (slider) and 1 W11419171 (Cntrl elec) and 1 W11260238 (Rotor)"

We serviced a

GENERAL ELECTRIC WASHER-DRYER COM

Model GUD27GESNOWW

Near Malibu, California 90265

Paul

Job Details: 03/22/2025

Tech was assigned as a helper;

We serviced a

WHIRLPOOL DRYER

Model WGD560LHW3

Near Los Angeles, California 91326

Sean W

Job Details: 03/22/2025

"Replaced motor and irregular noise and vibration still present,need to call techline.; schdld next appmnt for 3/24 MON !"

We serviced a

WHIRLPOOL RANGE

Model WGG745S0FS02

Near Montclair, California 91763

Jaime

Job Details: 03/22/2025

Rear right burner does not ignite needs to be replaced; ordrng 1 W11230935 (Holder) and 1 W10643269 (Holder) and 1 W11685612 (Holder) and 1 W10643271 (Holder) and 1 W10643272 (Holder) and 1 WPW10406878 (Burner) and 1 WPW10406797 (Burner) and 10 WP3368921 (Screw)s

We serviced a

GENERAL ELECTRIC WASHER

Model HTW265ASW0WW

Near Coalinga, California 93210

Esteban

Job Details: 03/22/2025

Different issue. Unit is draining water properly. Called be tag no answer. No faults or alerts found on navy bean device. Unverifiable issue. Speed sensor and control board on order. Follow-up required. ; ordrng 1 WH03X32158 (Speed sensor) and 1 WH22X38438 (Control board)

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Bakersfield, California 93307

Randy

Job Details: 03/22/2025

Cx complaint unit lid is broken. Was sent a strike. Ordering lid. Cx needs latest and last app ; ordrng 1 W11470212 (Lid)

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Bakersfield, California 93304

Randy

Job Details: 03/22/2025

Unit is not starting proper cycle. Keeps reading drain pump. Found issue with pressure sensor on board. Needs new acu. When I did get unit to run. Unit sounds like its cam worn out. drain pump is louder than normal. Ordering all parts needed. ; ordrng 1 W11603810 (Acu) and 1 W11239857 (Belt) and 1 W10721967 (Cam) and 1 W10919003 (Drain pump) and 1 W11652038 (Acu)

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Coalinga, California 93210

Esteban

Job Details: 03/22/2025

All fuse and thermostats tested good. Console not responding. To any selections. Unit has 240v. Called tech line no answer. Unverifiable issue. Parts on order follow up required. ; ordrng 1 W11627521 (Encoder) and 1 W11561663 (Console)

We serviced a

MAYTAG WASHER

Model MVW4505MW2

Near Earlimart, California 93219

Esteban

Job Details: 03/22/2025

"F7 e7 error code actuator tested good. Unverifiable issue. All other components capacitor, drain pump tested good. Called tech line tech line closed. Follow up required. ; ordrng 1 W11740022 (Control board)"

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Delano, California 93215

Esteban

Job Details: 03/22/2025

Drain pump and slider checked good. Stator getting power but just humming. Unverifiable issue parts on order follow up required. ; ordrng 1 W11687817 (Board) and 1 W10915701 (Rotor) and 1 W10754448 (Clutch) and 1 W10915700 (Stator) and 1 W11568984 (Lower harness)

We serviced a

MAYTAG WASHER

Model MVW6230HW0

Near Delano, California 93215

Esteban

Job Details: 03/22/2025

"Suspension was removed and replaced unit Unit will require extra labor and parts to complete repair. Agitator has fused with Gearcase. Unit will require the agitator. Part on order. Follow up,required. ; ordrng 1 W11550891 (Agitator)"

We serviced a

SPEED QUEEN DRYER

Model ADG4BRGS117TW01

Near McFarland, California 93250

Esteban

Job Details: 03/22/2025

Timer jammed. Broken knob. Parts on order follow up required. ; ordrng 1 D517560 (Timer) and 1 806597 (Kmob)

We serviced a

AMANA WASHER

Model NTW4516FW4

Near Oxnard, California 93035

Isidro

Job Details: 03/22/2025

"F3e1, pressure fault, also f1e1 control fault. Technical Service P ointer #: W 11766193 R ev B, correcting issue by; ordrng 1 W11603811 (ACU control board)"

We serviced a

GENERAL ELECTRIC RANGE - ELECTRIC

Model JBS60RKCSS

Near Patterson, California 95363

Nick D

Job Details: 03/22/2025

"Left front burner not coming on, verified all other 3x burners working on high. Verified customer paper work and uploaded, dispatched verified.; ordrng 1 WB24T10022 (INF switch) and 1 WB30T10145 (Heat element small)"

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Patterson, California 95363

Nick D

Job Details: 03/22/2025

"UI tested, lid lock tested good, on auto serv test found spin cycles not activating on any speed, agitation did work during test.; ordrng 1 W10913953 (Actuator shift) and 1 W11428524 (Capacitor) and 1 W11239857 (Belt)"

We serviced a

GENERAL ELECTRIC DISHWASHER - BUI

Model GDT550PYR7FS

Near Bakersfield, California 93314

Randy

Job Details: 03/22/2025

Wont wash. Tested. Fills and then stops. Timer keeps running. Bad pump n wash motor. Drains. Ordering wash motor; ordrng 1 WD19X25700 (Wash pump motor) and 1 WD21X25468 (Pressure sensor)

We serviced a

SPEED QUEEN DRYER

Model ADGE9BGS115TW01

Near Bakersfield, California 93311

Randy

Job Details: 03/22/2025

Unit makes squealing noises during cycle. Intermittent noises. Removed and replaced idler. Same issue. ; ordrng 1 RB170002 (Kit roller) and 1 D511255P (Belt)

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Bakersfield, California 93311

Randy

Job Details: 03/22/2025

Harness broke. Unit wont drain. Clothes stuck inside w water. Opened removed clothes. Removed water w vacuum pump. Ordering harness. ; ordrng 1 W11643701 (Harness)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEHZ02

Near Oceano, California 93445

Leo

Job Details: 03/22/2025

"Cx stated having water damage work done a couple of days back, fridges water line included in repair, ran diagnosEvap fan motor test, failed, also , see service pointer relating to drain clogged up. See Quick pics, unit is not clean in area prone to clog up drain tube.See service pointers relating to drain clogged up. Not sure if Cx signed waiver.Technical Service Pointer #: W11397260A and Technical Service Pointer #: W10632338EUnit.Pseudo for Monday.; schdld next appmnt for 3/24 MON !"

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Covina, California 91724

Stephen

Job Details: 03/22/2025

"Ran diagnostics. Had f7e5,f7e1, f2e1, f5e2 error codes. Not spinning or agitating, drain backing up. 3 count job. Allow 2 hours. Drain must be cleared before service. ; ordrng 1 W11454734 (Gear case) and 1 W10721967 (Splutch) and 1 WPW10006384 (Belt) and 1 W10528947 (Hub) and 1 W11550891 (Agitator)"

We serviced a

KITCHENAID REFRIGERATOR

Model KRSF705HPS05

Near Pasadena, California 91104

Stephen

Job Details: 03/22/2025

Not a recall different issue. Found center crisper bin cracked. ; ordrng 1 WPW10531078 (Crisper bin-center)

We serviced a

WHIRLPOOL WASHER

Model WFW560CHW4

Near Pasadena, California 91101

Stephen

Job Details: 03/22/2025

Unit is stacked in closet. Customer washed rugs plugging up sump hose. Helper needed. 2 count job. Allow 1 1/2 hours. Pending authorization. ; O-emld tckt

We serviced a

WHIRLPOOL WASHER

Model WTW4955HW3

Near Baldwin Park, California 91706

Jaime

Job Details: 03/22/2025

Found washer doing nothing except the locks on the house nothing this is a harness; ordrng 1 W11665968 (Harness)

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KPS1

Near San Marino, California 91108

Stephen

Job Details: 03/22/2025

"Ran diagnostics. Had f7e1, fAe2 error codes. Wash motor not running. Needs pump & motor, vent/fan. 2 count job. Allow 1 1/2 hours. ; ordrng 1 W11416362 (Pump & motor) and 1 W11414073 (Vent) and 1 W11629912 (Control)"

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ3

Near Oxnard, California 93035

Kenneth

Job Details: 03/22/2025

Found unit unit not washing. Found tiny steel mesh all inside the unit. Stuck all in the wash arms and blocked up wash motor. Unit needs new sumo assembly. As well as new wash arms. ; ordrng 1 W11550888 (Washarm) and 1 W11545334 (Manifold)

We serviced a

GENERAL ELECTRIC DRYER

Model GFD55GSPR3RS

Near Oxnard, California 93035

Kenneth

Job Details: 03/22/2025

Found door switch not registering door open and closed properly. Unit needs new door switch. Will replace control on return visit. ; ordrng 1 WE04X34281 (Door switch)

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Patterson, California 95363

Nick D

Job Details: 03/22/2025

Customer not answering door after several attempts; O-emld tckt

We serviced a

KITCHENAID RANGE

Model KSGB900ESS8

Near Los Angeles, California 91326

Paul

Job Details: 03/22/2025

"Need to call techline, replaced parts and unit reached desired temp and then got error codes a few minutes after. ; schdld next appmnt for 3/25 TUE !"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT2045VW

Near Porterville, California 93257

J.E.

Job Details: 03/22/2025

Cycled unit and found locked compressor. Also found system low on refrigerant. Ordering new compressor and evaporator. ; ordrng 1 5303918884 (Compressor) and 1 5304522324 (Evaporator) and 1 5303305677 (Filter drier)

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Fresno, California 93710

Timothy

Job Details: 03/22/2025

8-1 water code. Found the harness to the hot valve is damaged by rodents. Provided an estimate for repair. I do not recommend repair until the rodent issue is resolved.OFFICE READ THE STICKY NOTES!; ordrng 1 W11513255 (Valve)

We serviced a

GE WASHER

Model PTW605BSR1WS

Near Fresno, California 93722

Timothy

Job Details: 03/22/2025

Customer states the unit is not washing correctly. She has shown me a video of the unit full of water with clothes just floating on top of the water with no wash action. The auger and Washplate were loose. Tried to tighten the bolt with a hand tool on the loose auger and the soft metal screw snapped ! Now the unit will need a new gearcase too and more labor. Called TAG16149634 for documentation and tech support. The gearcase is out of stock with no ETA for delivery.; ordrng 1 WH03X34137 (Platform) and 1 WH43X32857 (Auger base) and 1 WH43X33058 (Auger) and 1 WH02X33797 (Screwed)

We serviced a

MAYTAG REFRIGERATOR

Model MRT118FFFZ01

Near Temple City, California 91780

Jordin Rogers

Job Details: 03/22/2025

Unit has s\s issue again frost pattern on evaporator is not throughout and there is a big ice ball on evaporation receiving tube; O-emld tckt

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Atwater, California 95301

Cruz

Job Details: 03/22/2025

Need work- cx has a video- knocking/grinding during all cycles- seen this before will need to order parts for 7nit. ; ordrng 1 W11510461 (Wash plate) and 1 W11449841 (Gear case) and 1 W11260238 (Rotor) and 1 W10754448 (Clucth) and 1 W10734521 (Slider)

We serviced a

AMANA DISHWASHER

Model ADB1400AMS1

Near Porterville, California 93257

J.E.

Job Details: 03/22/2025

Cycled unit and found faulty motor ordering parts for repair ; ordrng 1 W11613566 (Control board) and 1 W11613570 (Motor/sump)

We serviced a

MAYTAG REFRIGERATOR

Model MFX2676FRZ00

Near Bakersfield, California 93313

Randy

Job Details: 03/22/2025

Defrosted unit. Cleared drain tube. Removed and replaced clip brackets door and pan. Tested now drains and sealing as designed.

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW

Near Porterville, California 93257

J.E.

Job Details: 03/22/2025

Installed new control board and retested unit now working as designed job completed

We serviced a

MAYTAG WASHER

Model MVWC465HW2

Near Moreno Valley, California 92557

Kevin

Job Details: 03/22/2025

"Removed and replaced gearcase, basket, hub, agitator and suspension. All tests good. I did see a leak at customers plumbing during test. Informed customer of leak in plumbing connection."

We serviced a

WHIRLPOOL DRYER

Model WGD8127LW3

Near Hesperia, California 92344

Cesar

Job Details: 03/22/2025

Replaced control all tested good at this time

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDHV07

Near Bakersfield, California 93304

Randy

Job Details: 03/22/2025

Removed and replaced motor seperator divider harness damper control ice maker impeller and spacer. Tested now working as designed.

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW0

Near Ontario, California 91762

Jaime

Job Details: 03/22/2025

Replaced control y ran calibration. Washer Ok

We serviced a

AMANA WASHER

Model NTW4600VQ1

Near Moorpark, California 93021

Paul

Job Details: 03/22/2025

Unit was leaking from drain pump. Replaced with new drain pump and issue has been corrected. Drain pump seal was broken.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHZ04

Near Turlock, California 95380

Nick D

Job Details: 03/22/2025

Water filter failure not inserted in correctly needs replacing also. Filter replaced water dispenser back on.Customer educated on replacing filter every 6 months or when water dispenser water pressure is low.

We serviced a

GENERAL ELECTRIC WASHER

Model PFW870SPV0RS

Near Victorville, California 92394

Cesar

Job Details: 03/22/2025

Customer instructed on install floor on home is flexing and combined with the flexing of the pedestal it is making the unit shake during spin cycle

We serviced a

WHIRLPOOL OVEN

Model WOES3030LS01

Near Victorville, California 92394

Cesar

Job Details: 03/22/2025

Replaced oven control all tested good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDBM00

Near Victorville, California 92395

Cesar

Job Details: 03/22/2025

Found ice maker cycles over and over never calling for water. Replaced ice maker all tested good

We serviced a

WHIRLPOOL M/W OTR

Model WMH31017HS06

Near Atwater, California 95301

Cruz

Job Details: 03/22/2025

"Cx states unit started sparking during cooking, now unit pops breaker when trying to use it, found capacitor, mag, transformer, diode, to be packed with grease, there a short causing unit to pop breakers, I replacing all heating components, door switches, Cnrtl elec, to fix unit."

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Phelan, California 92371

Cesar

Job Details: 03/22/2025

Leaking out of valve where solenoid meets valve body. Replaced valve all tested good

We serviced a

WHIRLPOOL DRYER

Model WGD4910XQ1

Near Moreno Valley, California 92555

Kevin

Job Details: 03/22/2025

"Unit not heating. I found open thermal fuse. Removed and replaced fuse. Tested unit, all tests good.; used 1 WP3392519 (THERMAL FUSE) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model ART318FFDW10

Near Livingston, California 95334

Cruz

Job Details: 03/22/2025

"Fixed- installed new part (gasket) applied adhesive around door channel, remove wrinkles, with heat gun- gasket is sealing to cabinet - cx ok repair"

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS3

Near Burbank, California 91505

Oscar

Job Details: 03/22/2025

Visual and physical inspection leaded me to complete motionless unit after cycle selection and start.Some a new pump assembly was installed and unit resumed normal operation.

We serviced a

GENERAL ELECTRIC DISHWASHER

Model GDT630PFM6DS

Near Moreno Valley, California 92553

Kevin

Job Details: 03/22/2025

Upper spray arm broke off. Removed and replaced upper spray arm and manifold. All tests good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ19

Near Perris, California 92570

Kevin

Job Details: 03/22/2025

Water dripping after getting water at dispenser. Installed regulator behind console to stop drip. All tests good.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS03

Near Oxnard, California 93030

Isidro

Job Details: 03/22/2025

"Installed new filter head unit is now dispensing water as designed at this time of service, cx approved repair"

We serviced a

GENERAL ELECTRIC WASHER

Model GTW325ASW0WW

Near Commerce, California 90022

Stephen

Job Details: 03/22/2025

"Replaced speed sensor, mode shifter, motor pulley, and belt. Cleaned transmission pulley. Cleared fault codes. Agitates in drain & spin. Replaced and programmed control. Fills, drains, rinses, locks/ unlocks properly at this time. Advised customer NOT to wash comforters, rugs, carpets, bathmats, pillows, drapes, curtains, shoes, dog beds, large blankets, bed covers, or any oversized loads. Instructed customer on unbalanced loads, to put roof over washer ( unit outside ). Complete."

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Oxnard, California 93030

Kenneth

Job Details: 03/22/2025

Found unit not spinnning. Found unit had a worn drive hub. Went to remove washplate and could not remove washplate. Ended up breaking off washplate to access the metal teeth and went to remove those and the entire drive shaft came out of gearcase. Removed gearcase. And replaced. Gearcase. Actuator. Belt and cam. Installed removed old hub and replaced. Replaced washplate. And put everything back together. Then replaced suspension due to excessive bounce. Tested unit. Unit is working properly. ; used 1 W11239857 ( Belt) from stock

We serviced a

KITCHENAID M/W OTR

Model KMHS120ESS11

Near Manteca, California 95336

Andrew

Job Details: 03/22/2025

Thumping or Rumbling Noises - sounds like broken plastic from door. Cx complaint. Ran diagnostics. Found dent in front door. Found found loose door hinge. Attached door to hinge. Checked out components. Okay. Operation as according to designed protocol .

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW3

Near Grover Beach, California 93433

Leo

Job Details: 03/22/2025

"Opened up unit to find broken drive belt, replaced with new one, closed up unit to test it and unit spins and heat as it should, Job complete."

We serviced a

MAYTAG WASHER

Model MVW5435PW0

Near Wasco, California 93280

Esteban

Job Details: 03/22/2025

Loose wire at drain pump. Connection was safely secured. Unit will unit is now draining properly. Unit is working as intended.