"IM, MAIN BOARD, UI, VALVE could be factoring in issue,call tech line unit possibly had a brownout, UI acting glitchy, not able to engage diagnostics program, it blinks and does not to commands. 5304535682 Main control board, 5304529572 UI display board, 243297608 Icemaker and 5304536607 Water valve.; ordrng 1 5304535682 (Main control board.) and 1 5304529572 (UI display board.) and 1 243297608 (Icemaker) and 1 5304536607 (Valve.)"

"Needs 2 man Customer is not home , office called no answer , I am ordering parts the unit will need to repair the unit when I come back to properly repair the unit; ordrng 1 WB10X35573 (Latch asm) and 1 WB49X45009 (Magnitron) and 1 WB27X35382 (Diode) and 1 WB18X35517 (Thermostat)"

"Needs 2nd man and 3 call count help to tilt the washer, dryer combination and replace gear case and belt and pulley The dryer potion is working ok , dryer vent needs to be cleared , washer needs belt and pulley asm when washing unit screeches , tight quarters will need a second person to move unit in a tilted position to replace the belt and pulley asm screeching when unit is agitating will get the gear case as well ; ordrng 1 W11454741 (Gear case) and 1 W11239857 (Belt) and 1 W10721967 (drive pulley)"

Unit wont start. Internal light not working. Button responds but wont start. Bad interlocks switches. Ordering switches and holders. ; rqstng P&A on 4 W10211972 (Switch)s and 2 W11214928 (Interlock)s and 2 W11715912 (Spring)s and 2 WPW10120235 (Rod push)s and 1 WPW10128850 (Arm)

Leak water bottom door.spray arms broken.reroute for parts.; ordrng 1 WPW10498900 (Wash arm) and 1 WPW10491331 (Spray arm bottom)

not operating properly. Cx complaint. Upon arrival. Ran diagnostics. Found error code. 4*43. Washer Found W11612326. Shorted not spinning. And sump assembly . Found shorted Vent fan assembly W11648151. Fan motor W11558695. Ordered parts more worked needed ; ordrng 1 W11558695 (Vent fan) and 1 W11648151 (Vent assembly) and 1 W11612326 (Motor pump) and 1 W11613479 (Sump assembly)

"Technical Service Pointer #: W 11766193 Rev BAction Required: M andatoryRelease Date: March , 2025 Unit doing a long safety drain, ordering parts :Control Board W11603810 and WPW10285518 SWITCH, ROTARY ENCODER (5 POSITION)', SWITCH-CYC; ordrng 1 W11603810 (Control board) and 1 WPW10285518 (SWITCH, ROTARY ENCODER (5 POSITION)', SWITCH-CYC)"

Cycled unit and found refrigerator leak at evaporator. Unit will need new compressor and new evaporator. Ordering parts for repair. 5yr sealed warranty per entitlement. Collected service fee; ordrng 1 W11557425 (Compressor) and 1 W11550396 (Evaporator) and 1 W11109499 (Drier)

Please order control board; ordrng 1 W11603810 (Control board)

Cycled unit and found f2e2 check connection to Ui all connection look good unit has faulty Ui. Ordering part. ; ordrng 1 W11478526 (UI)

Cycled unit and found pressure system error drain pump continue to run non stop. Faulty control board. Ordering control board ; ordrng 1 W11603810 (Control board)

Unit not heating causing timer not to advance in auto cycle. I found that the flame sensor is not seeing the heat from the ignitor to light. Failed flame sensor. ; ordrng 1 WP338906 (sensor) and 1 WPW10328463 (coil-valve)

"Control box is shorted out and not working again,and fresh food gasket is falling off, need to call techline to see why new control box would short again for a third time.; schdld next appmnt for 4/7 MON !"

Found unit not cooling properly. Found frosted over evap. Fan not running. Ordering new style defrost heater and air tower. ; ordrng 1 5304523833 (Heater) and 1 5303918891 (Air tower)

"Cx stated unit has same issue as last time. Confirmed broken suspension right left holder removed and replaced it. Also found damage balance ring and door latch from unbalanced condition. Cx stated he is loading evenly and similar fabrics. Cx is upset and asked if I can recommend a new one. Informed Cx we are a repair company and cannot make those calls. Calibrated and tested ops/ unit working in the mean time but I will have to order balance ring due to damage attached picture to sd file. Unable to document with factory it is closed today. Will also call them on Monday; ordrng 1 W11043544 (Tub ring), used 1 W11307244 (Latch) from stock"

Water leak from tub ring.reroute for part.; ordrng 1 MVWC465HW3 (Tub ring)

"Blower not running. Found power ( 120v )to blower motor on all speeds, motor harness has continuity. Had external blower in attic. Needs blower assembly. EST for blower part only. 751.69. Needs HVAC technician or installer to replace blower( not accessible due to HVAC ducts in the way. Customer refused to pay. Send bill to customer. WPW10294026 blower is needed. SEND BILL TO CUSTOMER for 145.00 !; saved tckt"

"Warped door. Top bearing worn out, belt worn out, noisy blower and motor. Broken latch and strike. Parts on order follow up required. ; ordrng 1 WE17X24535 (Motor and blower) and 1 WE03X25314 (Top bearing) and 1 WE03X29897 (Belt) and 1 WE01X25316 (Latch) and 1 WE01M10007 (Strike)"

Cx complaint. Door feels heavy. Upon arrival. Ran diagnostics. Found hinge loose. Found pad on a hinge loose. Unable to reattach pad and hinge. Order parts more work needed.; ordrng 2 WP8268961 (Pad)s

Not heating. Cx complaint. Upon arrival. Ran diagnostics. Found magnetron magnet noises. Ordered parts needed more work. W10832024 thermostat. 11.11 amps ; ordrng 1 W11495561 (Magnetron) and 1 W10832024 (Thermostat)

Noisy Cx complaint. Upon arrival. Ran diagnostics. Found noisy Gearcase bearing. Found leaking seals. Needs more work. W11551646 corrosion Spanner nut. W11449840 gearbox. W11550891 agitator corrosion stuck on. Please allow extra time for repair. ; ordrng 1 W11550891 (Agitators) and 1 W11449840 (Gearbox) and 1 W11551646 (Spanner)

"Need work- found fabric softener dispenser not dispensing- dispenser drawer not dispenser, found a short in wiring and cntrl elec- ordering parts for unit. Requires authorization.; ordrng 1 W11569112 (Dispenser) and 1 W11621180 (Cntrl elec)"

"Need work- agitator is broken, cx found pieces inside wash basket, look at pictures- water is splashing out of tub ring onto floor- will use tub ring on next visit- ordering part for unit. ; ordrng 1 W11614636 (Agitator)"

Found noise coming from the pipe exhaust and blower housing. Allow time for repair ; ordrng 1 WPW10211911 (Housing blower) and 1 WPW10342188 (Pipe exhaust) and 1 WPW10344699 (Collar) and 1 WP697772 (Blower) and 1 W11364931 (Motor)

"Unit not igniting in bake cycle, bake electrode, wire harness, spark module control and valve solenoid all checked good, I suspected bad main power house control board, customer declined repairs at this time of service. $145.00 CK Auth# R4AFFW; ordrng 1 W11205353 (Main control power house)"

Different issue. Unverifiable intermittent noise. Ordering actuator and drain pump. Techline closed. Parts on order follow up required. ; ordrng 1 W11396717 (Drain pump) and 1 W10913953 (Actuator) and 1 W11395618 (Capacitor) and 1 W11543997 (Control board)

Found dispenser leaking out front it is shooting water towards the outer front part of dispenser. Also found f9 e1 code will clear out filter before replacing pump. Cx stated he would unstuck unit with his son and requested follow up on Saturday April 19 2025; ordrng 1 W11319789 (Pump)

Please send technical assistance. Cx complaintp. Stove burner is not working. Display 5304522786 not powering up. Upon arrival. Ran diagnostics. Found display button not sensing. Found left side burners not powering up. 5304516862.; ordrng 1 5304522786 (Control) and 2 5304521812 (Induction)s and 1 5304519431 (Induction left) and 1 5304516862 (Panel board)

"Ui not responsive, and control board locking and unlocking door, ordered new Ui and board.repair exceeds covered amount and repair needs authorization.; ordrng 1 W11322903 (Acu) and 1 W11316252 (Upper harness) and 1 W11319991 (Ui)"

"Stop missing from upper right rack,ordered new stop.; ordrng 1 WPW10082861 (Stop)"

"The dual gas valve was successfully installed and tested. Due to receiving the wrong part even when the right part number was requested, The temperature sensor was not replaced. So please reorder the right part this time. Also, the error code F9 E0 was immediately splashed on the screen, for which I had followed Service matters instructions to the T.Unplug range or disconnect power.Check wires and connectors between main control (P6) andpower cord.Check that the L1-L2-N wiring (pigtail) from the power outletis correctly connected to the range terminal block.Replace all parts and panels before operating.Plug in range or reconnect power.Start a self-clean cycle and observe for 1 minute to ensurethat operation is normal. Enter the diagnostic mode to viewthe Faults screen. Press START TIME or DELAY START toclear each Fault code(s).Also, I was unable to clear the code because I was no able to make a selection after the code is on the display. My plan of attack is as follows, order the right temperature sensor and schedule a return visit, then Ill contact whirlpool support for further instruction. ; O-emld tckt"

"Reinstalled missing foot..Rattling noise is gone, Cx stated his ice cream was runny, making noise in back machine section,Compressor readings:1.05 and 1.07 respectively, Compressor temp, pseudo for Monday text Miguel ; cstmr sgnd Dsclmr"

Found unit with a faulted compressor. Compressor is locked up and not turning on. Compressor is covered under a 5 year warranty. But labor is not. Customer would like to order a new light and gasket. Quoted customer $1089.32 Customer would like to think about repair and weigh different options. Collected $145 via CC on iWallet (Autho# ECR94F) Will collect $944.32 on return visit if customer wishes to make repair. ; ordrng 1 W10830055 (Gasket) and 1 W11527432 (Module) and 1 W11547313 (Compressor)

"Temps at65f , no frost, found bad wire harness to both compressor and condenser fan, toggling on harness stops and starts both, when running getting 120vac, need new harness.; ordrng 1 5304519649 (Wire harness power)"

"Unit was found emitting compressor malfunction noises, gurgling Yoder capillary line due to leak in evaporator location, loud high pitched rattling low or restricted refrigerant fluid, sealed system tech JJ assigned to second opinion/conduct necessary repairs to unit.Ordering following parts :W11578004 ASSEMBLY, EVAPORATOR, W11504450 4/1.8 NR MS 00 (CAPILLARY TUBE TO EVAPORATOR), W11506619 8 NK MS 00 (CHARGING TUBE TO COMPRESSOR), W11580057 COMPRESSOR, W11578570 CONNECTOR (7 MM TO 4.5 MM, BRASS) (HIGH SIDE TO CONDENSER); ordrng 1 W11578004 (EVAPORATOR) and 1 W11504450 (CAPILLARY TUBE TO EVAPORATOR) and 1 W11506619 (8 NK MS 00 (CHARGING TUBE TO COMPRESSOR)) and 1 W11580057 (COMPRESSOR KIT) and 1 W11578570 (CONNECTOR (7 MM TO 4.5 MM, BRASS) (HIGH SIDE TO CONDENSER))"

"Visitor center is closed, no access to base, need to reschedule; schdld next appmnt for 4/8 TUE !"

Unit is having ongoing issue need to reschedule for tech line availability ; schdld next appmnt for 4/7 MON !

Failed to bring right display board. I need the black one; ordrng 1 W11594228 (Display board)

Something is off with the new gear case. After replacing the parts the Spanner nut wont fit. Need to call techline but ordering all parts for unit now. ; ordrng 1 W10811960 (Basket) and 1 W11219115 (Tub) and 1 W11393685 (Gear case) and 1 W10734521 (Slider) and 1 W10915700 (Rotor) and 1 W11032711 (Washer)

Installed lid latch still having locking issues found broke lower wire harness ; ordrng 1 W11643701 (Harness)

Unit is making a screeching sound. After replacing the slider the unit still was doing the same thing. ; ordrng 1 W11449841 (Gear case) and 1 W11260238 (Rotor) and 1 W11195971 (Stater) and 1 W10754448 (Cluch) and 1 W10902814 (Wash plate)

"Washer not completing drain and spin cycle pause half way,drain pump and actuator works inner mitten.reroute for parts ; ordrng 1 W10919003 (Pump drain) and 1 W11481722 (Actuator) and 1 W11428524 (Capacitor)"

"F1E1/F2E1 codes, found burnt terminal and burnt wire on ACU and main harness, need to order parts to fix problem, previously heating element and idle pulley replaced.; ordrng 1 W11618917 (Control board ACU) and 1 W11700548 (Main harness)"

"HMI,encoders, wire harness replaced. HMI now responds to test mode but now F7-E1 code shows, wrong signal from UI J1-J4 nor receiving 120vac,tried erasing fault code, tried recalibration , both did nothing to advanced wash.Test 1 after power testing recommends replacing UI control board, this is a new board just recently installed.Attention note: REQUESTING SENIOR TECHNICIAN to assist on 7th return visit, not helper requesting a new ACU.; ordrng 1 W11626074 (CONTROL)"

Knob loose. Cx complaint. Upon arrival. Found loose knob. W11174696. Ordered ; ordrng 1 W11174696 (Knob)

"Removed and replaced parts listed, tested ops unit working properly. No damage by tech. Core for 34977127 not obtained because Part does not actually have a core."

"Removed and replaced all parts listed, tested ops unit working and no damage by technician"

Drain pump and control board were removed and replaced. Unit is draining properly now. Unit is working as designed.

"Replaced gear case, slider, agitator screw, noticed door damaged, did not cause lid lock problem,ran drain, spin cycle customer verified visually.; used 1 W10734521 (Slider) from stock"

Replaced defective spark module and electrode. Unit test ok. Complete

Replaced parts all tested good at this time

Removed and replaced sump and motor. Tested ops no leaks and no damages

"Ran diagnostics. Had f0e1, f3e1, f0e2. Cleared error codes. Found pressure tube kinked. Unkinked pressure tube. Load tested rinse & spin. Locks/ unlocks, fills, washes, drains, rinses, dispenses, and spins properly at this time. Instructed customer on unbalanced loads, spin speed settings. Unit is working properly as designed. Complete."

"Checked the unit the fresh food drain was clear , replaced the water reservoir, water, valve and filter, housing assemblies unable to test cause unit was pulled out of its normal spot by the customer customer is going to install back"

Replaced damper tested good at this. Did find ice build up around damper housing indicating air leaks

"As going through the process of elimination, only needed parts were replaced. And unit was successfully tested."

"Installed new agitator and its now agitating as designed, cx approved repair at this time of service"

"Replaced bad harness. Replaced main control board, calibrated unit and ran diagnostics. F7E4 error did not re appear. Unit is now working properly."

"As a new timer was installed, a functionality testing was successfully completed."

Control board and speed sensor were removed and replaced. Unit passed all test. Unit is working as designed.

"Replaced bad door switch, unit test ok. Complete"

"Fixed- installed all new parts (gear case, slider, clutch, wash plate, ) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"

"4W4VFC - 2214218 - collect 370.29 iwallet- cx paid for parts and labor- compressor was covered under 5 warranty plan- installed new part (compressor, damper, cntrl elec, thermistor) tested pressure system with nitrogen, no leaks, - pulled deep vacuum- charged unit with 53 grams of r600a - unit has begun cooling- cx o repair"

Frozen ice maker fill tube. Defrosted fill tube and tested line heater all checked good

Removed and replaced heater and adpt control. Unit now working properly. No damage by tech.

"Replaced previous new timer block& main knob, knob no logger wobbling, tested all 3x cycles made sure it buzzed and turned off motor."

Drain pump was removed and replaced. Unit passed all test. Unit is working as intended.

Replaced beT and valve all tested good

"Replaced main control board and drain pump, part received did not have filter trap included, programmed new control board to units personality #4, filled some water, washed and drained, it passed all tests,Unit runs as designed,Job complete."

"Fixed- installed new part (gasket) removed wrinkles with heat gun, freezer gasket is now sealing to cabinet- cx ok repair"

"Replaced main board, calibrated unit and ran unit on a normal wash cycle. Unit is now working properly."

Ice build up in FC. I found d that the door was not closing due to ice. I defrosted ice build up and tightened rails and tested gaskets. All tests good.

Installed a new user interface. Dishwasher Ok

Installed all parts unit is testing fine

Cycled unit and found broken agitator. Installed new wash plate and retested unit now working as designed job completed

"Installed new wash motor kit and sump, unit is now washing as designed leak free, cx approved repair and service"

"Replaced HMI, and harness, unit test ok. Complete"

"Cx complaint. OVEN, OVEN DOESN'T BAKE OR BROIL-DOESN'T BROIL. Upon arrival. Ran diagnostics. Found relay fault. Installed relay board. Tested components out Okay. Operation as according to designed protocols"

"Checked the unit not shifting from wash to spin , replaced the clutch pulley assembly belt and shifter tested operations. Unit is working as designed now at this time."

Unit wont start. Keeps making clicking noise and wont start. Tested found bad latch. Removed and replaced latch. Tested. Now working as designed

"Glass was hanging, it became detached. Replaced with new glass door. Unit is missing logo but customer is ok with that. Job complete"

Unit not starting cycle and just hums. I found that the capacitor had failed causing motor to just hum. Removed and replaced capacitor. All tests good.

"Installed new timer and advanced it, unit is now cooling properly as designed, cx approved repair and service"

Installed the new lid assembly As well I was a switch assembly. Washing machine OK

"Replaced harness and reset unit, fans and compressor running properly, advised Cx to wait several hours to start loading food in it, nice cold air in both sections,Job complete."

Installed suspension rods unit is draining fine do not need pump. Unit tests fine

Unit is not stopping. Tested unit wont go past time set. Bad timer. Removed and replaced timer. Tested now working as designed

Cycled unit and found faulty suspension. Installed new suspension and retested unit now working as designed job completed.

Icemaker and water valve was not needed. Removed and defrosted ice in fill tube. Unit is working properly.

Installed new board unit is testing fine calibrated unit

Cycled unit and found faulty lid lock installed new lid lock and retested unit now working as designed job completed

"Install a new compressor on the unit. Pressurize the system and no leaks found at this time. Vacuum the unit and unit holds vacuum. Recharge the system with 64 g of refrigerant R600a. Retest the unit and now it starts cooling down. Inform the customer they need to wait at least 24 hours for proper cooling, and 26 for ice production. Job complete."

Cycled unit and found broken harness at pump connector. Installed new harness and retested unit now working as designed job completed

"I found the unit working as designed, unable to contact tech support at this time of service"

Dishwasher front left leg not balance. Door not closed good.Adjusted front leg door locked good.

"Checked the unit touch control would not go into diagnostics , checked power to the main board tested at the ui connection no dc voltages , replaced the main board tested at, tested the ui board still not reacting to touch controls, but now lights up and is able to work and function with the LED in the back of the board but still not reacting to touch control replaced the user interface tested operations unit now works as designed at this time"

Found unit going from sensing to done then Starts draining. Found unit with loose capacitor leaking. Removed and replaced capacitor. Tested. Now working as designed

"I found the evaporator fan motor not running, I installed new evaporator fan motor and fan, unit is now circulating air and operating as designed, cx approved repair and service"

"Had lid switch assembly And the horse tube assembly too replaced washer ok; used 1 W10810403 (Lid), and 1 W10802689 (Hose tube) from stock"

New issue unit cooling fine but ice maker has e5 code for bad thermistor. Temp in fc is 2 degrees f. Removed and replaced ice maker asked Cx to monitor ops