Found washer exexively loud wen spinning reposition back right foot retested check out ok complete no dents or dings cause by tech.

Replaced defective ice maker and fill tube heater. Cleared fault code.Tested ok

Inspected unit found heat element failed. Replaced with pre id part and unit is working per design. Job comple

"Optimum temp is 60-90 degrees. Minimum temp 55 degrees and maximum temperature 110 degrees. Today the temperature outside in the garage is 54 degrees. NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near an oven or radiator"

Replaced defective ice room fan and blade. Replaced defective right side door gasket.Tested ok

Replaced dispenser and door seal tested unit all tested good

Found pulley cover not installed. Found screw that hold on cover stripped out. Causing unit not to spin. Customer would need gearcase. Customer opted out of gearcase at this time. Says he doesnt want a new unit taken apart. Informed customer that as long as nothing goes under the washer. Then there wont be anything to worry about

"Same complaint as the last complaint , customer is complaining about the water drips from the dispenser , its not anything like constant drip customer doesnt like the design of the machine we have already called tech line CASE #85825346 and it was for the same thing then too , they also added when ice dumps theres a crash noise , this is normal as well ice cubes dropping makes noises , operating normal"

Customer concern unit not feeling properly also not dispensing enough detergent. Fully tested unit and found unit is working as designed. Instructed customer on proper loading and cycle selection. Job completed.

"F8E3 error code found I ran a full diagnostics on unit check drain hose, inlet hose and drain pump and found that the bellow was not secured correctly. Found leaking from bottom of Bellow; I just did the Bellow and no more water is leaking anymore. unit working as designed."

Tested found lid switch jammed adjusted tested working to spec

"A door must be removed. Then, reinstalled to have that panel replaced.

Found the return duct frozen over. Reason for not cooling properly. I removed all the ice from the return and evaporator. Bi metal checked ok. The heater also checked ok at 58 ohms. Unable to determine what caused it. Recommend the customer wait 24 hours for the temperature to get back to normal. Job completed.

"Igniter was replaced kept shutting off within couple seconds and dryer wasnt as hot at first, after replacing parts issue got fixed Cx also mentioned since the washer leaves water extremely wet dryer takes longer to heat which would make sense why also dryer is taking longer than usual to heat, Cx is aware. Dryer is fixed, job completed."

Replaced broken fan blade. Tested unit all functions are working properly. Job complete

Installed parts tested check out ok complete no dents or dings cause by tech.

Installed new adjusters on the top shelf and new wash motor. Reassembled and tested. No leaks after service. Everything is now operating as designed. Job complete.

Removed and replaced control. Calibrated and ran auto test. All ops checked good

"JB out 1/12/23. Customer states refrigerator will intermittently power down, shut off and food spoil. Customer states one finding unit powered down, power cord is unplugged, then plug back in unit reception calls again for a period of time, and then shut off again. Upon arrival found unit running and cooling properly. Ran all refrigeration, diagnostic tests, all tests past. Unable to verify mechanical malfunction today. No recommendation for repair yet. Advised customer most likely electronic control main board or user interface or power. Supply board is at fault however, unit is not displaying fault today so no accurate diagnosis can be made today.

Install the new repair kit on the unit. Retest the unit and no more noise complain. Job complete

"Checked the unit the 2 doors close correct the floor is slanted forward , and customer is over stuff in the refrigerator took pictures to proof so raise the front so the unit will self close better and it does now advise customer not to overload the refrigerator and freezer sections to where they protrude past the shelving other than that unit is working as designed at this time now"

Installed drian pump tested working to spec

Installed spluch tested working to spec

86049190 Robert. Installed new leds and tested unit. No response from leds. Contacted TECHLINE. Damaged thermal wire or non serviceable connector. Unit up for review. Frigidaire will contact customer for further steps

"Found unit infested with cockroaches, causing control board to have a thermal event and damaged control board and harness. Called tech line7735466490"

Found unit not draining. Found unit pump not running. Bad pump. Removed and replaced pump with truck stock. Now draining and spinning as designed. Cx complaint the dog blankets and dog related items dont dry. Cx instruct on not reccomed to wash those in here because can break apart and break pump again. Ran diagnostics passed no error codes. Cx okayed Unit now working as designed Job complete ; used 1 W11399437 (Pump) from stock

Open wire harness in ice maker. Installed ice maker. Unit tested ok

"All ok with the washer no error codes stored. Unit passed diagnostic cycle. Verified no issue with any wiring, control system, or component. Unit operating as designed"

Cycled unit and found broken red wire at UI pantry harness. Call tech line to document unit not repairable. Job completed.

JB out 1/12/23. Customer states Washington is waiting for sometime in this caused water damage behind washer on floor and wall. See quick photographs taken. verify because of water. Leak is manufactured joint of red water supply hose. This hose is not part of the washing machine is not provided by Maytag. This water supply hose was purchased separately and may or may not through a manufactures warranty. Refer customer to Lowes for warranty information. No repair made or needed to watch on machine. Advised customer of one time courtesy no charge on a notification service call for the appliance itself.No charge to customer. JOB COMPLETE

Installed part tested check out ok complete no dents or dings cause by tech.

Cx stated unit has trouble making ice or dispensing water. Checked unit found no issue test 56 e0. Adjusted controls and emptied ice bin asked cx to monitor for ice production and to report any problems.

Found right door with torn gasket causing erratic cooling. Removed and replaced gasket. Used heat gun to shape gasket. Now sealing. Now working properly Job complete

Removed and replaced agitator base. Tested unit. All tests good.

Replaced light panel and door gasket. Tested unit all functions are working properly.Job

Found unit has stuck button and control panel needs to be replaced. Reads stuck button. Unit is unresponsive to any type of control. 0x code. No communication to controls. Customer is going to think about what step they are going to take. Pay for it or call manufacturer. Will get back to us. Customer is calling manufacturer.

Installed new gasket and formed to cabinet. All functions are now working as designed.

Installed new thermistor and tested unit working as designed

"Unit had frosted over with ice build on freezer covering sensor. Defrosted all ice build up and noticed wire on wire harness was not touching with other connector. Placed back and issue will be fixed no further problems,job completed."

Tested unit customer has video from December tested no error codes working to spec at this time

Fixed- found freezer gasket had popped off causing condensation and ice buildup- I then popped gasket back into channel test door gasket is now sealing to cabinet. Cx ok repair

"The radiant sensor was replaced and tested the dryer right after and started heating right away, there was no further issue Cx was satisfied, job completed ."

Removed and replaced board tested all works good at this time.

Installed parts tested check out ok complete no dents or dings cause by tech.

"Checked the refrigerator found the unit not working lights tested the temp not maintaining in the fresh food section , the DC CIRCUIT is not working , the door switches not reacting when the door is open , disconnected the deli drawer harness from the back of the deli drawer pulled power customer reset the circuit tested operations the lights came back everything running correctly at this point no other issues found. OK as of right now allowed 48 hours for everything to come back to normal"

Found the blower wire connector not pushed in all the way. Had to open the metal contact in the connector in order for it to be pushed in all the way. Was able to insert all the way. Tested after repair all ok.

"On arrival loud screeching noise heard, found seized bearings. Quoted for repair cx approved. Installed repair kit. Tested, unit functions as designed.; used 1 4392067 (Repair kit) from stock"

"Replaced the control board assembly. Need to reschedule and send a sealed system technician. Failure is within the sealed system and inverter, compressor is not running, just hums ##S15330, part# W10903340 compressor with inverter Need to create another ticket for the sealed system issue SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM"

Upon arrival found unit with uneven temperature causing failure. Check temperatures on the compartments and freezer 0F and fresh is 38F. This unit is pack off fun and the air flow is no the right. Inform the customer how to set the food and now the air flow is good. Inform the customer for more tips go to the owners manual. Job complete

"Found slider sticking in the lower position causing unit not to agitate, replaced shifter all tested good"

Found moisture in the fridge. Needed the door adjusted. And gaskets reformed. Adjusted door and reformed gaskets. Tested unit. All ops checked good

"Cx stated it sounded like a whistling noise, tested ops with and with out a load, tightened stator unit checks ok"

Touch panel not responding had to reset unit to get panel to work. Connection at ui is loose fully seated connector all tested good

Installed all parts listed tested working to spec

Customer stated that the unit is not washing. Removed and replaced main control and lock tested all works good at this time.

Water was leaking from water connector. Replaced connector and tested unit job complete

Replaced control board and user interface. Unit tested ok

Install the new thermostat on the unit. Retest the unit and unit password all the tests at this time. Job complete

"Cycled unit and Broken support, wheels and bad idle pulley. Install dryer repair kit and re-tested unit all test pass. Job completed.; used 1 4392065 (Repair kit) from stock"

Rattling noise has stopped prior to arrival. Customer is concerned about microwave heating time. Ran output test and unit is preforming within specs.Tested ok

Replaced Gearcase. Tested unit all functions are working properly. Job complete

Unit not draining and wont unlock door. I found that the drain pump was clogged causing no drain. I cleaned out drain pump. All tests good.

Replaced components and tested unit. Unit now working as intended.

"Installed ignitor and spark module. Tested, unit functions as designed. Did not need burner caps or heads."

"The customer reports the unit is taking too long to dry. Checked units ops, the unit is working properly, the burner is cycling on and off as designed. Found excess lint at the exterior vent outlet. Advised the customer to use timed dry on smaller loads, to avoid the Ecodry feature. The unit is working as designed."

Customer stated that the refrigerator lights are on but nothings running found jazz board is not responding removed and replaced control tested all works good at this time.

Replaced part needed. Found module was burnt and replaced. Checked unit out and working correctly now. Preheat broil and bake are working now. Tested and checked out. Job completed

Ran vent test and unit failed. Cx has xtra long vent hose. Also vent need to be cleaned. Uni passed all test after disconnecting vent. Job complete

"Installed part tested check out ok complete no dents or dings cause by tech.; (created new UIS, deleted prior attachment to UisID 361515)"

Installed latch. Tested unit. Unit is working properly. Customer approves function at this time.

Replaced compressor all tested good

I found the air gap full of waste. I cleaned out air gap and unit ran properly.

"Replaced compressor, pressure tested 10 minutes.Pulled vacuum, charged 5.5 R134a.Operating as designed."

Customer stated that the unit is not finishing cycles. Found error code for long drain. Found failed pump. Removed and replaced pump tested all works good at this time.

JB out 1/12/23. Customer states unit(s) do not clean well and bottom drawer unit sometimes has water standing it. Inspected unit and found installer has not installed dual drain lines as outlined in the supplied installation instructions manual. The supplied DUAL drain hose joiner ( 2 into 1 drain adapter with check valves) has not been used. Only ONE drain line is used to connect the drain to the existing kitchen sink Air gap device. BOTH DRAIN LINES ARE TO BE SEPARATELY RUN TO THE DRAIN JOINER THEN CONNECTED TO A COMMERCIAL STYLE DUAL AIR GAP DEVICE. REFER CUSTOMER BACK TO HOME DEPOT INSTALLER TO return and CORRECTLY reinstall both drain lines using the factory supplied joiner into a DUAL AIR GAP DEVICE. Advised customer installation corrections are not made or covered by the manufacturers warranty and are the responsibility of the installer used. ADDITIONALLY water temperature being supplied to the dishwasher is far below that if the required 120f MINIMUM as outlined in the instructions. Recommend the purchase and use of a point of use hot water heater under the kitchen sink set to 125f to supply no less than 120f at the moment if start up. No parts used today. No charge to customer. Installer must return and correct installation.

"F0e5. Cleared error code. Calibrated machine, ran diagnostics, all units ops check fine. Drain pump is working properly, no burnt smell present."

"Units blower was making excessive noise when the fan was turned on. Inspected blower and found its plastic housing was rubbing the wheel. I was able to put the housing back into its intended position. There was a clip that wasnt seated properly. Afterwards, the sound was gone and everything is now operating as designed."

Cycled unit and found broken lid lock also found over suds error caused by customer not using HE detergent customer must use HE detergent on this model. Informed customer of findings. Installed new lid lock and retested unit. Job completed

"Removed and replaced ice door motor and ice door, cx will monitor and report any issues."

Replaced panel drawer is now closing properly. Tested unit all functions are working properly.Job complete

"Installed the new control board, and user interface. Dishwasher works ok"

Installed sump assem. And soap dispenser. Tested unit. Unit is working properly. Customer approves function at this time. No leaks found.

"Fixed- installed new parts (motor evap, condenser motor) no grinding or Whistling sound at this time- cx ok repair"

"Installed new motor. Still grinding, found this is coming from damaged hanger holding motor. This part is no longer available. WD01X10416. Documented under cx phone number."

needs a compressor- compressor is locked up- cx is going to purchase a newer model unit-

Same issue came back months later. Icemaker is over filling with water. Installed all new parts. Icemaker and valve. Cx will let us know if issue persists.

"Remove defective unit. Install new unit. Tested new unit, works as designed. Customer stated unit had a broken ice machine."

Installed new icemaker. Icemaker will take 24 to 48 hours to return to normal operation. Customer will let us know if the problem persists.

"Found fridge low on Freon. It has an undetectable leak. Nitrogen, UV Drier was installed. But, no luck locating the internal leak. SR 7735486617. Called tech support SR# 7735486617"

Installed new water valve and tested unit working as designed

"Replaced compressor & filter dryer, checked for leaks, recharged seal system, unit cooling at this time."

Found the unit operating at the moment but it seems the longer it stays on the louder the compressor gets. When the hot gas valve is activated the compressor makes a very loud noise. The condenser fan is running just fine and no error codes found. Unable to verify complaint but I believe it may be a sealed system issue. Customer will call back if anything. No changes prior 30.

"Replaced RR and RF switches. All surface burners, indicators are working properly at this time. Complete."

Found dryer connected to a restricted vent verified with whirlpool vent checker. Cleaned the interior of the dryer was full of line potential fire hazard. Unit ok after repair. Recommend customer contact a vent cleaning company in order to clear dryer vent.

Replaced HV and UI controls. Unit is cooling properly at this time. Instructed customer not to block edges of shelves. Complete.

Adjusted door on left side.Tested ok

Unit not cooling in both compartments. I found that the unit had leaked out R600. I leak checked and found it leaking from lock rings in back compartment. I removed lock rings and soldered sleeves. Removed and replaced drier. Charged system with 68g R600. All tests good. ; used 1 W11109499 ( Drier) from stock

Removed and replaced parts listed. Tested ops unit now checks ok

"Found broiler burner not connected to gas line, set burner to gas line and tested unit working as designed"

"Unit was dripping water from water valve (cold) into motor and back basket looks like motor is burnt and getting 25;f error code, Cx says he will try to get parts himself and fix. I charged 135 cod. Job completed"