Service History 207 - Appliance Repair Specialists

We serviced a

WHIRLPOOL REFRIFGERATOR

Model WRS315SNHB00

Near Thousand Oaks, CA 91360

Giovanni M

Job Details: 02/04/2025

CX has a leak in the SS. Ordering the compressor and SS parts now ; ordrng 1 W10309988 (Compressor) and 1 Bubblespry and 2 WPW10143759 (Dryer)s and 3 W10913906 (Coupler)s

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model GDE25EYKHRFS

Near Malibu, CA 90265

Giovanni M

Job Details: 02/04/2025

Refrigerator door poppes open when the freezer door is closed. Called tech line and they want to replace the bottom hing and catchSR#15689358 ; ordrng 1 WR02X24877 (Closer) and 1 WR13X29171 (Hinge) and 1 WR02X24905 (Pin)

We serviced a

GENERAL ELECTRIC WASHER

Model GFW550SSN5WW

Near Bakersfield, CA 93314

Chase

Job Details: 02/04/2025

After installing new parts same issue. Upon button latch being pressed down lock continues to buzz. Called ge tech line. Confirmed stuck triac on main control. Ordering part needed.SR#15690168; ordrng 1 WH22X37837 (Main control)

We serviced a

WHIRLPOOL M/W OTR

Model WMMF7330RZ00

Near Lancaster, CA 93536

Samson

Job Details: 02/04/2025

Reordering defective door assembly.; ordrng 1 W11731160 (Door assembly)

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Fresno, CA 93727

Joe P

Job Details: 02/04/2025

"Ran diagnostic test, drain stays on all time . Control is stuck in drain mode, checked pressure hose good. Ordering control board. Will return. ; ordrng 1 W11603810 (Control)"

We serviced a

GE DRYER

Model GFD85ESPN1RS

Near Bakersfield, CA 93307

James

Job Details: 02/04/2025

"Unit pops breaker right after start is pressed. Ordering main control, motor, wire harness and lock. Requesting extra call time for harness checks and techline call. Customer aware that unit must be made accessible for repair. ; ordrng 1 WE22X34599 (Main control) and 1 WH03X32157 (Motor) and 1 WE16X33977 (Blower) and 1 WE08X32439 (Main harness)"

We serviced a

GENERAL ELECTRIC DRYER

Model GFD45GSSM1WW

Near Arvin, CA 93203

James

Job Details: 02/04/2025

Aloes new shaft and idler arm. Inspected top bearing and found slide areas cracked and broken could not install new slides to damaged top bearing. Ordering new top bearing assembly. ; ordrng 1 WE03X25094 (Top bearing assembly)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FGHC2331PFCA

Near Bakersfield, CA 93312

Chase

Job Details: 02/04/2025

"Confirme 120v to icemaker but will not harvest, ice in mold. Will order new icemaker and schedule for Friday per cx request. ; ordrng 1 5304468880 (Icemaker)"

We serviced a

WHIRLPOOL WASHER

Model WTW8127LW2

Near Bakersfield, CA 93311

Randy

Job Details: 02/04/2025

"Removed and replaced suspension. Tested was okay until got fast. Issue in the Gearcase and rotor. Wobbley knocking noise. Ordering Gearcase rotor and washplate. Requesting autho. 4 call count ***; rqstng P&A on 1 W11449841 (Gearcase) and 1 W11260238 (Rotor) and 1 W11195971 (Stator) and 1 W11510461 (Washplate), ordrng 1 W10752187 (Screw) and 1 W10734521 (Slide)"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF577KPS02

Near Bakersfield, CA 93309

Randy

Job Details: 02/04/2025

"Unit wont make ice. Tested valve test and failed to fill ice maker mold nRemoved and replaced valve and still wont fill. Dispenser working. Tested ice maker and squealing. Small ice cubes on front of fascia Found e5 error code on ice maker fan weak. . Ordering all parts needed. ; rqstng P&A on 1 W11482384 (Housing) and 1 W11658802 (Ice maker) and 1 W10864519 (Adapter), ordrng 1 W11741469 (Heater) and 1 W11087201 (Fill tube heater)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KRMF706ESS04

Near Bakersfield, CA 93314

Aaron

Job Details: 02/04/2025

"Checked the unit the freezer section is no longer defrosting and has a 4 inch thick block in the freezer evaporator , needs to be defrosted and orders main board failed to read and going to defrost and user interface board for programming and the evaporator fan motor that has all the defrost thermostat and sensors on it in the freezer, ordered parts ; ordrng 1 WPW10675033 (cntrl-elec) and 1 W11330971 (U I board)"

We serviced a

FRIGIDAIRE RANGE - GAS

Model FFGF3054TSJ

Near Bakersfield, CA 93314

Chase

Job Details: 02/04/2025

"Cx claims she sent in the escrow papers. Will submit for auth just incase. Also said they bought extended warranty. If escrow papers werent sent Cx will need to go through extended warranty company to have them send us over correct work order, Cx complaint that oven is not getting up to temp. Also blowing breaker when oven is not even in use. Faulty control, burnt triac. will order and replace part needed. Submitting for auth. ; ordrng 1 5304533248 (Control)"

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Paso Robles, CA 93446

Leo

Job Details: 02/04/2025

"Error codes present on arrival, F6E3 communication errors between ACU HMI-UI control panel, need replacement.F0E3 overloaded, Cx advised on how much and loading procedure. Order following parts: W11478526 ASSEMBLY, PANEL-UI and W11624943 ACU ASSEMBLY; ordrng 1 W11478526 (ASSEMBLY, PANEL-UI)"

We serviced a

WHIRLPOOL REFRIGERATOR

Model KRSF705HPS04

Near Bakersfield, CA 93308

James

Job Details: 02/04/2025

Boyd with techline sr 7740886132Unit has frozen reseviour again. Contacted techline. Was given part number for gasket. Was told to order 3 of them and use them to stop airflow from entering reseviour section. ; ordrng 3 W10684392 (Gasket)s

We serviced a

AMANA WASHER

Model NTW4516FW3

Near Bakersfield, CA 93301

James

Job Details: 02/04/2025

"Cold water valve stuck closed. Grinding noise from belt and cam. Ordering new valve, belt and cam. ; ordrng 1 W11239857 (Belt) and 1 W10721967 (Cam) and 1 W11210463 (Valve)"

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near Bakersfield, CA 93307

James

Job Details: 02/04/2025

Unit locked with water inside. Unit has lid lock failure. Opened lid for Cx. Ordering new lid lock.; ordrng 1 W11670519 (Lock)

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KPS1

Near Santa Clarita, CA 91354

Felipe S

Job Details: 02/04/2025

"Upon arrival found unit with error code F9E1 and FAE2, this about no draining and vent wax motor. Call tech line and report this issue, after inspection they recommend to do check for the water inlet valve assembly. They recommend to check for good water pressure, and is good, check for wires pinch or damage by the inlet water valve assembly, this wires are good and they have continuity. The recommendation at this point is replace the water valve and the inlet water valve. SR: 7740884437 Garry ; ordrng 1 W11535094 (Water inlet valve assembly) and 1 W11434044 (Water valve)"

We serviced a

GENERAL ELECTRIC RANGE - GAS

Model GGS500SV1SS

Near Oxnard, CA 93035

Isidro

Job Details: 02/04/2025

"Found the unit not powering on, power supply checked good, correcting issue by; ordrng 1 WB27X48608 (Control flashed) and 1 WB07X47348 (Overlay)"

We serviced a

WHIRLPOOL M/W OTR

Model WMH31017HS3

Near Los Angeles, CA 91311

Paul

Job Details: 02/04/2025

Need to order main board and come with blanket to cover stove.; ordrng 1 W11441128 (Motor fan) and 1 W10832024 (Thermostat meg) and 1 W10163422 (Thermistor) and 1 W10850446 (Capacitor) and 1 W10836753 (Transformer) and 1 W11175576 (Main board) and 1 W10754299 (Magnetron)

We serviced a

WHIRLPOOL RANGE

Model WFG320M0MW0

Near Moorpark, CA 93021

Ian Y

Job Details: 02/04/2025

Ordered LP conversion kit. Will install on return visit. ; ordrng 1 W11557997 (LP conversion kit)

We serviced a

GENERAL ELECTRIC RANGE - ELECTRIC

Model JVM3160DF8WW

Near Santa Paula, CA 93060

Isidro

Job Details: 02/04/2025

"Broken door latch, cx had pop on hand, correcting issue by; ordrng 1 WB56X44649 (White door assembly)"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS07

Near Ripon, CA 95366

Martin

Job Details: 02/04/2025

Dropped data loggers off in unit ; O-emld tckt

We serviced a

MAYTAG REFRIGERATOR

Model MSS25C4MGZ09

Near Modesto, CA 95355

Martin

Job Details: 02/04/2025

#7740884011Replaced bad cover Called tech line they recommended adding silicone to door seal ordering silicone ; ordrng 1 W10841140 (Silicone)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FGRU19F6QFD

Near Bakersfield, CA 93314

Erick

Job Details: 02/04/2025

"Installed new parts on unit . Pulled vacuum, recharged system, inspected for leaks and found none . Unit is now cooking at the time of service. Unit passed all tests at the time of service. Unable to collect the remaining , will collect next day ; schdld next appmnt for 2/5 WED !"

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Hanford, CA 93230

Enrique

Job Details: 02/04/2025

Customer concerns: dry not heating. Need main harness (burnt red wire and terminal block) customer will buy power cord. CUSTOMER AVAILABLE WEDNESDAYS AND THURSDAYS.; snapped 4 QuickPics

We serviced a

WHIRLPOOL M/W OTR

Model WMH32519HZ07

Near Oakdale, CA 95361

Martin

Job Details: 02/04/2025

#7740881899Found right rear hook had burnt mark called tech line they said that its because Cx is not removing rack when not being used that is causing the sparks recommended replacing hook and covering mark with universal silver ; ordrng 1 8212473 (Universal silver) and 1 W10840795 (Hook)

We serviced a

GENERAL ELECTRIC RANGE

Model JGBS66REK6SS

Near Le Grand, CA 95333

Cruz

Job Details: 02/04/2025

"Now right front, right rear burners are not adjusting to a low flame- will need to replace them- ordering parts for unit. ; ordrng 2 WB21X20260 (Valve)s"

We serviced a

WHIRLPOOL WASHER

Model WFW95HEDW0

Near Pasadena, CA 91105

Oscar

Job Details: 02/04/2025

"NOTE,As this will be the second time customer doe not respond to our calls and and not being available for service, next time and as per Erick, we will assess a $145.00 service fee. ; O-emld tckt"

We serviced a

WHIRLPOOL DRYER

Model WGD5620HW0

Near Los Angeles, CA 91042

Oscar

Job Details: 02/04/2025

"A general check up was performed and besides UI panel not properly responding, unit is working as designed. Replaced UI panel recommended.; ordrng 1 W11378949 (UI panel) and 1 W11223753 (Badge)"

We serviced a

JENN-AIR OVEN

Model JJW2830LL01

Near San Luis Obispo, CA 93401

Leo

Job Details: 02/04/2025

Part damaged.; ordrng 1 W11602612 (Door Panel)

We serviced a

MAYTAG WASHER

Model MVW7230HC1

Near Arroyo Grande, CA 93420

George

Job Details: 02/04/2025

F0e3. F7e8. File#7740310294. Found washer staying stuck on sensing called manufacture ran thrue diagnostic advising to replace this parts as recommendation .; ordrng 1 W11195971 (Stator) and 1 W11260238 (Rotor) and 1 W10734521 (Slider) and 1 W10754448 (Clutch)

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN9WW

Near Grover Beach, CA 93433

George

Job Details: 02/04/2025

#15688908. Case. Found washer lid lock unlocking and locking put smart h q lid lock error active failure called manufacture check unit wen lock only reading 4.3 need 100 need to order lid lock to complete service.; ordrng 1 WH08X37937 (Lidlock)

We serviced a

SPEED QUEEN WASHER

Model AWN632SP116TW02

Near Oxnard, CA 93030

Kenneth

Job Details: 02/03/2025

Drain pump did not come with a new idler like I had expected it to. Ordering idler pulley. Rescheduled customer for Monday 2-10-25; ordrng 1 959P3 (Idler)

We serviced a

WHIRLPOOL WASH/DRY COMBO

Model WFC8090GX0

Near Calabasas, CA 91302

Richard

Job Details: 02/03/2025

Upon arrival found unit leaking from detergent assembly looked up these parts. The detergent assembly complete is no longer available and neither is the inlet valve. Advised customer of this. The unit is not repairable due to detergent dispenser assembly no longer available advised customer he will receive a phone call from whirlpool third-party in a few days to see how they want to go about this unit is no longer repairable job complete; ordrng 1 WPLW11256731 (NLA)

We serviced a

MAYTAG DISHWASHER

Model MDB8959SKZ2

Near Los Angeles, CA 91307

Ian Y

Job Details: 02/03/2025

"Found unit having issues draining. Customer says its inconsistent and will work sometimes. Ordering control, pump and motor assembly. Will call Techline while installing. ; ordrng 1 W11524458 (Control) and 1 W11197948 (Motor and sump assembly)"

We serviced a

FRIGIDAIRE FREEZER

Model FFFH17F4QW0

Near Bakersfield, CA 93304

Chase

Job Details: 02/03/2025

Air creeping in from gasket causing frosting up. Will replace gasket. ; ordrng 1 5304505529 (Gasket)

We serviced a

MAYTAG WASHER

Model MVW7230HC1

Near Bakersfield, CA 93307

Chase

Job Details: 02/03/2025

"F7e3, f0e3Having difficulties agitating. All other functions are running. Will need to replace stator and rotor. ; ordrng 1 W11195971 (Stator) and 1 W11260238 (Rotor)"

We serviced a

ELECTROLUX ELECTRIC RANGE

Model ECCI3668AS

Near Atascadero, CA 93422

Jack

Job Details: 02/03/2025

Possibly the board on right. Needs to been in state to test. New part number 1401153922619 original board is 5304527612. Needs 240 for display to work. There is no neutral for this unit. File number 87913407. Russ with tech line. Customer needs to call in if unit is in the state of no power. Possibly breaker or the board needed thats being ordered. Wont be available unit Thursday this week. 2/6/25. From tech line. It seems to a new number. ; ordrng 1 1401153922619 (Generator assembly board)

We serviced a

FRIGIDAIRE WASHER

Model FLCG7522AW3

Near San Luis Obispo, CA 93401

Jack

Job Details: 02/03/2025

Customer wasnt available. Called office. Talked to tech line and ordering the valve assembly 5304524455. Leaking out of the coil area. ; ordrng 1 5304524455 (Valve assembly)

We serviced a

MAYTAG WASHER

Model MVWB765FC

Near Santa Maria, CA 93458

George

Job Details: 02/03/2025

F7e9 error found washer intermently squeak bouncing around on a spin need this parts.; ordrng 1 W11611438 (Control)

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ0

Near Victorville, CA 92392

Brian

Job Details: 02/03/2025

F1-E2 error. Control issues. Ordering control and user interface ; ordrng 1 W11613564 (User Interface) and 1 W11637583 (Control)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ11

Near Stevenson Ranch, CA 91381

Ian Y

Job Details: 02/03/2025

Found units ice maker making ice intermediary. Will be changing out ice maker and main valve. ; ordrng 1 W11446816 (Main valve)

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS2

Near Hughson, CA 95326

Timothy G

Job Details: 02/03/2025

Inspected unit and unit seemed to be leaking at the diverter valve location. Need to follow up with new sum assembly. Follow up scheduled for Thursday. Notify Cx with time slot.; ordrng 1 W11416362 (Sump)

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0O

Near Atwater, CA 95301

Timothy G

Job Details: 02/03/2025

"Inspected unit and ran tests. Pulley is squealing and not shifting properly its loud when motor runs to engage. Need to follow up with parts. Its ok to send Cruz to repair if needed. Cx needs to be notified of return vist to make sure someone is home. Requested following Monday, that is my scheduled off day. That is why it would be fine to send any tech, see note. ; ordrng 1 W10721967 (Sprutch) and 1 W11239857 (Belt) and 1 W11481722 (Actuator)"

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Tulare, CA 93274

Enrique

Job Details: 02/03/2025

"Washer was not draining. Pump broken blue wire. Installed lower harness, performed calibration. Washer operating as designed. No leaks.; used 1 W11643701 ( Harness) from stock"

We serviced a

KITCHENAID OVEN

Model KODE500ESS21

Near Los Angeles, CA 91343

ERICK H

Job Details: 02/03/2025

"Cx states both upper and lower ovens take a long time to cook food, especially when using both ovens simultaneously. Cx states this has been an issue since day 1. Preheated both ovens to 350 degrees Fahrenheit. Both upper and lower ovens preheated to 350 in 14 minutes. Once preheated, upper oven cycling between 335 and 356 degrees Fahrenheit. Average temp 345 degrees Fahrenheit. After preheated, lower ovencycling between 325 and 367 for an average temp of 346. Unit is operating as designed with factory calibration. Per Cx request, I adjusted both ovens +10 degrees Fahrenheit. Unit operating as designed. Job complete."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS01

Near Modesto, CA 95350

Timothy G

Job Details: 02/03/2025

Inspected unit and found that the start relay was not locked in and must have fallen out. Put start relay back and unit started cooling. Job completed

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ11

Near Oxnard, CA 93035

Ian Y

Job Details: 02/03/2025

"Found units water filter cover came off not allowing filter to stay mounted properly. Realigned and secured filter cover. Tested, unit now filtering water properly."

We serviced a

WHIRLPOOL OVEN

Model WFG525S0JZ6

Near Pismo Beach, CA 93449

George

Job Details: 02/03/2025

Found oven getting 340 on 350 test unit contain temp custoto preheat oven give it a few extra preheat minutes for better response complete.

We serviced a

WHIRLPOOL REFRIGERATOR

Model ED5FHAXSQ01

Near Agoura Hills, CA 91301

Richard

Job Details: 02/03/2025

"Upon arrival, inspected unit found unit not dispensing. Any ice at all during my inspection removed motor cover found auger motor completely seized filled with ice cleared ice retested unit unit would still not spin auger gave customer an estimate for the auger motor and shaft. Customer is deciding not to go ahead with the repairs."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ08

Near San Luis Obispo, CA 93401

Jack

Job Details: 02/03/2025

Customer is having problems with manifold. The filter was also bad. The original one the hook to release wouldnt come out unless using a pliers. Ran 80 oz of water through new filter. Plus checked out sprang on release Replaced housing and new filter comes out no problem. Customer see hour it comes out now and how the housing is supposed to help push out the filter. Job completed

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS1

Near Los Angeles, CA 91311

Ian Y

Job Details: 02/03/2025

Found drip tray lead disconnected. Re secured. Tested unit now working as designed.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW485SW0WB

Near Apple Valley, CA 92307

Brian

Job Details: 02/03/2025

Inspected unit as necessary. Diagnosed suspension worn. Removed and replaced all four suspension rods. Leveled unit to specifications. All OK.

We serviced a

WHIRLPOOL OVEN

Model model

Near Beverly Hills, CA 90210

Tim B

Job Details: 02/03/2025

No visible model or serial numbers on unit. So unable to diagnose or call techline for further assistance.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS0

Near Bakersfield, CA 93311

Chase

Job Details: 02/03/2025

"Confirmed there is a clog in plumbing. Water pouring from air gap and disposal, cx will get plumber out to correct issue. Everything with dishwasher is checking out great."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Los Banos, CA 93635

David

Job Details: 02/03/2025

Found faulty icemaker replaced icemaker unit working as designed

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Pismo Beach, CA 93449

George

Job Details: 02/03/2025

Installed parts tested unit checking out ok customer paid remeinder with I wallet complete.

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Oxnard, CA 93033

Isidro

Job Details: 02/03/2025

"I found a broken lid took picture, I replaced lid unit is now as designed averaging, cx approved repair and service"

We serviced a

WHIRLPOOL OVEN

Model WFG320M0MS0

Near Victorville, CA 92392

Brian

Job Details: 02/03/2025

Diagnosed door gasket torn. Removed and replaced door gasket. Reassembled and tested operation. All OK

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Los Banos, CA 93635

David

Job Details: 02/03/2025

Found bad suspension rods replaced suspension rods tested unit unit working as designed

We serviced a

WHIRLPOOL WASHER

Model WFW85HEFC1

Near San Fernando, CA 91340

ERICK H

Job Details: 02/03/2025

"Cx states door remain locked after failure. Unit seems to have canceled cycle shortly after starting and begun emergency drain. Removed lid and manually unlocked door. Clothes was dry. No visible water in tub. Let emergency drain cycle complete. After unit went into standby I checked error codes. F3e1(water level system error), f0e1(load detected during cleaning washer cycle), and f8e3(overflow condition) error codes present. Cleared codes. Performed diagnostic cycle. Unit completed cycle with no functional failures. No error codes came back. I did notice drain pump running slow during testing. Removed rear panel to gain access to drain pump and coin catch. Coin catch has lint that was preventing washer from draining properly and cause Cx complaint. Removed obstruction. Retested. Unit now draining properly. Job complete."

We serviced a

JENN-AIR DISHWASHER

Model JDTSS246GL0

Near Los Angeles, CA 90049

Tim B

Job Details: 02/03/2025

Replaced broken adjuster tested unit unit functions as normal

We serviced a

MAYTAG DRYER

Model MGD5630HC4

Near Victorville, CA 92392

Brian

Job Details: 02/03/2025

Inspected unit as necessary. Diagnose igniter failure. Removed and replaced igniter. Tested operation. All OK.; used 1 279311 (Igniter) from stock

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near Ripon, CA 95366

Timothy G

Job Details: 02/03/2025

Ran tests and unit had a failed capacitor. Replaced and tested unit. Job complete

We serviced a

THERMADOR OVEN

Model POD302W/02

Near Bakersfield, CA 93309

Jim

Job Details: 02/03/2025

Temperature too low. Replaced boards. Unit tested ok

We serviced a

WHIRLPOOL DRYER

Model WED4850HW0

Near Manteca, CA 95337

William

Job Details: 02/03/2025

"Unit noisy at blower wheel, Replaced obstruction on blower wheel housing, ran dryer cycle, unit operating as designed."

We serviced a

KITCHENAID DISHWASHER

Model KDFE104HPS1

Near Bakersfield, CA 93308

James

Job Details: 02/03/2025

"Started cycle, drain working as intended.water valve working. No heat. Replaced heater and control. Unit now working as intended."

We serviced a

FRIGIDAIRE RESIDENTIAL REFR

Model FRSS26L3AF7

Near Paso Robles, CA 93446

Jack

Job Details: 02/03/2025

Checked out and found the fill tube was bad. The seal was bad cause leaking down back wall on to evaporator fan. Also the screw was looking bad seeing it was starting to rust. Cleaned up and checked and ran fill test. No more leak out of fill tube. Job completed customer.

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Manteca, CA 95337

William

Job Details: 02/03/2025

"F4E3, checked voltage to pump, Replaced wash pump/motor, ran self diagnostic cycle, unit operating as designed"

We serviced a

WHIRLPOOL WASHER

Model MVWC565FW1

Near Claremont, CA 91711

Jaime

Job Details: 02/03/2025

Basically rebuilt washing machine. Had to work the back panel on upper panels.

We serviced a

KITCHENAID OVEN

Model KODE507ESS03

Near Riverside, CA 92509

Robert U.

Job Details: 02/03/2025

Found the upper sensor not reading correctly and reason for heating issues. The lower oven is heating just fine. I replaced the open sensor and ran a bake cycle n all functions restored to the upper oven. All functions back to working order. Job completed.

We serviced a

SPEED QUEEN DRYER

Model ADEE9RGS175TW01

Near Bakersfield, CA 93311

Jim

Job Details: 02/03/2025

Installed new heater and both drum supports. Unit tested OK

We serviced a

WHIRLPOOL DRYER - ELECTRIC

Model WED5010LW1

Near Orcutt, CA 93455

George

Job Details: 02/03/2025

"Found dryer not drying correctly found coil connector not inserted came off reposition secure it retested unit getting hot complete.; (created new UIS, deleted prior attachment to UisID 468510)"

We serviced a

KITCHENAID DISHWASHER

Model KDFM404KPS1

Near Riverside, CA 92503

Robert U.

Job Details: 02/03/2025

Found the door not closing properly and door kind of falls when opening. I found the right side hinge out of place. The spring came off. I reinstalled the hinge spring and that resolved the issue with the door closing. All other functions tested properly. Job completed.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ1

Near Victorville, CA 92395

Brian

Job Details: 02/03/2025

Inspected unit unit as necessary. Diagnosed wash motor failure. Removed and replaced sump and pump assembly. Tested operation. All

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Arvin, CA 93203

James

Job Details: 02/03/2025

Installed new harness and tested unit. Unit now working as intended.

We serviced a

KITCHENAID DISHWASHER

Model KDTM405PPS1

Near Lathrop, CA 95330

William

Job Details: 02/03/2025

"Replaced wash pump/motor assy, ran self diagnostic cycle, checked for water leaks, unit operating as designed"

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW4

Near Bakersfield, CA 93312

Jim

Job Details: 02/03/2025

Replaced coil kit. Unit tested ok

We serviced a

AMANA DRYER

Model NGD4655EW0

Near Simi Valley, CA 93063

Ian Y

Job Details: 02/03/2025

"Removed and replaced pulley rollers and belt. Tested, unit now going into cycles."

We serviced a

WHIRLPOOL WASHER

Model MVW6230HW0

Near Fresno, CA 93704

Timothy

Job Details: 02/03/2025

Installed capacitor belt and cam assembly. Ran a service test and found the unit operating as designed.

We serviced a

KITCHENAID FREEZER

Model KSRK25FVMS00

Near Thousand Oaks, CA 91320

Richard

Job Details: 02/03/2025

"Upon arrival, inspected unit found unit not dispensing ice at all Inspected auger motor found auger motor was seized, found bad and coupling as well. Replaced all three retested unit unit is now dispensing ice as intended is also making ice as intended. All operations are normal job complete"

We serviced a

MAYTAG WASHER

Model MHW5630HW3

Near Bakersfield, CA 93306

James

Job Details: 02/03/2025

Replaced bellows and clamp. Tested unit. Unit working as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHM05

Near Atwater, CA 95301

Cruz

Job Details: 02/03/2025

"Fixed- found ice maker motor to be stripped and inlet valve to be defective- removed bad ones and then installed new (ice maker, inlet valve) ice maker test pass- water filled mold- allow 12-24 hrs for ice production- cx ok repair"

We serviced a

WHIRLPOOL WASHER

Model MVWB765FC3

Near San Dimas, CA 91773

Jaime

Job Details: 02/03/2025

Installed the new suspension assembly. Washing machine OK

We serviced a

FRIGIDAIRE DISHWASHER

Model GDPH4515AF1B

Near Bakersfield, CA 93313

Chase

Job Details: 02/03/2025

"Installed new ui, console, and dispenser. All ops now working as designed."

We serviced a

WHIRLPOOL DRYER

Model WGD9400SW

Near Beverly Hills, CA 90210

Tim B

Job Details: 02/03/2025

Found drum seal torn replaced drum seal with adhesive also advised customer to keep door open while adhesive cures

We serviced a

MAYTAG WASHER

Model MVW4505MW2

Near Highland, CA 92346

Rod

Job Details: 02/03/2025

Leaks water from under productConfirmed leak at water inlet removed and reinstalled as manufactured.was not installed in machine properly.

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW4

Near Redlands, CA 92373

Rod

Job Details: 02/03/2025

Core returnedOperates with heat only o drum actionconfirmedreplaced broken belt and retrieved as designed operation was restored with no gaze leakscore sent it back to office.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SNHM08

Near Ceres, CA 95307

Timothy G

Job Details: 02/03/2025

Inspected unit and unit was cooling. Removed panel in freezer and found the evaporator motor just bouncing. Used my finger and fan started spinning. When stopped fan will not start.Replaced motor and fan is working. Also advised Cx about packing so tightly with bagged product in freezer. Adjusted temperature. Cx says ice cream has never gotten very hard its always soft. Explained how air restriction can cause warmer spot. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Simi Valley, CA 93065

Richard

Job Details: 02/03/2025

Upon arrival removed and replaced main control board with bad transponder also replaced damaged lower wire harness tested unit. Unit passed all test and is not working as intended job complete.

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW1

Near Los Banos, CA 93635

David

Job Details: 02/03/2025

Found bad actuator and cam replaced actuator and cam unit working as designed

We serviced a

WHIRLPOOL DRYER

Model WGD7120HW1

Near Bakersfield, CA 93311

Chase

Job Details: 02/03/2025

Installed new duct and steam valve. All ops now working as designed.

We serviced a

WHIRLPOOL [

Model WTW7120HW1

Near Los Angeles, CA 91307

ERICK H

Job Details: 02/03/2025

Strike has broken since previous visit. Used strike from truck stock to replace broken strike. Replace gear case. Tested and calibrated unit. Unit operating as designed. Job complete.; used 1 W11457841 (Strike) from stock

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ08

Near Highland, CA 92346

Rod

Job Details: 02/03/2025

"Returned, replaced defective ffd door seal .designed operation was restored"

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW0

Near Modesto, CA 95355

Cruz

Job Details: 02/03/2025

"Fixed- installed new parts (ACU, drawer, 4 shocks, panel) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Turlock, CA 95380

Cruz

Job Details: 02/03/2025

"Fixed- installed all new parts (gear case, slider, stator, clutch, 6 screws, rotor, suspension, cntrl elec, lower harness) calibration test pass- auto test pass- no leaks- no errors- cx ok repair"

We serviced a

WHIRLPOOL DRYER

Model MLG26PDBWW1

Near Los Angeles, CA 91342

ERICK H

Job Details: 02/03/2025

Replaced repair kit. Tested unit. Unit operating as designed. Job complete.

We serviced a

KITCHENAID OVEN

Model KODE500ESS21

Near Ventura, CA 93003

Isidro

Job Details: 02/03/2025

"Installed new blower wheels and ACU control , tested unit to 350 degrees unit is now heating and operating as designed at this time of service"

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Los Angeles, CA 90049

Tim B

Job Details: 02/03/2025

Replaced the control board and HMI harness ran through diagnostics and tested unit functioning as normal

We serviced a

KITCHENAID DISHWASHER

Model KDFM404KPS3

Near Mentone, CA 92359

Rod

Job Details: 02/03/2025

"Returned, replaced Switch . Designed operation was restored with no leaks."