Cx exhaust that goes out to house was completely blocked and exhaust was crushed and extremely long Advised cx to clean that out and get short hose Complete

"Checked the unit dead , customer self cleaned , then cooled off ,then the control fuse went bad - cx approved , tested operations unit now heats correct at this time

Found the unit had a loose connection at the gas coils. After reinserting the coil connector that restored the heat. I ran a vent test as well and recommended the customer have it cleaned out. Dryer isolated passed the tested. Heat cycling test passed. Job completed.

"Checked the Left front power burner was not igniting when cold , aligned up the power burner correct and and widened the upper left port , ops now work correct, power burner now ignite correct at this time"

"When I was closing the door I noted some of the LEDs were lit. I checked for fault codes and ran a service test. The unit had no faults and passed its service test without generating any new faults. Found the end of the power cord connected to an adapter that was loose when I disconnected the power. Checked for secure wire nuts. Both lines were secure and there is no evidence of overheating. Opened panel and removed the door latch. During inspection, when I was actuating the latch, something flew out of it. I could not find what that might have been. I lubricated the latch and reinstalled it. I checked all the harness connections and applied a dielectric compound to the connections for better conductivity. Reassembled unit and ran another service cycle. The unit completed the cycle without fault. Started a normal cycle to make sure the unit works in consumer mode. Aligned the door to the latch for better closing. The strike was forcing the door slightly left. Currently the unit is operating a s designed. Informed the customer the service charge is valid for 30 days and off the unit should act up they could recall service without another service charge. The unit seems to be in good condition. I focused on the latch and connections since this was the most likely issue other than a control failure . Both are checking ok currently."

"On arrival unit has no ice, found broken wires at lower hinge of fc door. Needs door. Advised Cx to seek assistance as repair is costly. Cx paid service fee."

"Installed the sump and motor assembly. Ran diagnostics, diagnostics completed with no errors present. Verified that No leaks are present. Unit is functioning as designed. Did not install the board and drain pump.

Repositioned drain line. Drain line longer hitting tub during spin cycle and making clicking sound.

"Replaced freezer door, checked ice maker functions, unit operating as designed."

"Heater is drawing .9 amps, water valves are .4 amps, unit in run cycle drawing .3 amps. Polarity and ground is all correct. Called tech line and theyre only willing to write a report but not will not condemn the unit. Received a service number 7735748056"

Customer stated that the unit is not washing the dishes. Found sump is not working. Quoted customer for replacement.

Upon arrival found unit with cover for the motor and belt fell into the ground cows in the noise when the unit was agitate. Readjust the cover and return the unit and now unit is working properly. Job complete.

Removed and replaced heater assembly. All OK.

Installed new drain pump

"Assembly oven bottom was replaced because old one was bended, also cap was replaced because of smaller size, no further issues, job completed."

Off balance load error. Removed and replaced slider. Tested operation. All ok!

Replaced faulty capacitor has zero microfarads. Tested after repair all ok.

Installed liner kit. All functions now working as designed.

"The rotor was replaced because when put on a drain and spin the rotor was not spinning or agitating, once replaced retested with drain and spin and this time saw rotor move correctly no further issues, job completed."

Found actuator bad replaced tested working properly

Removed and replaced main control and coin interface. I calibrated unit in diagnostic. Unable to test coin mech due to keys for washer not being at apts at this time.

Removed and replaced main control and coin interface. I calibrated unit in diagnostic. Unable to test coin mech due to keys for washer not being at apts at this time.

Replaced control board. Washer now working properly.

Unit not cooling. Tested unit and found evaporator fan not running. Removed and replaced fan motor. Tested unit. All tests good. ; used 1 WP2315549 (EVAP FAN MOTOR) from stock

Found idler bad replaced with dryer kit tested working properly ; used 1 4392065 (Kit) from stock

Removed old unit installed new unit tested new unit new unit operating as designed had a nice wide path for the refrigerator to get through. It was just move forward and out the door.

"JB out 3/7/22 customer states washing machine does not spin, clothing, dryer, efficiently and clothes are left wet at the end of the cycle which requires more time in the dryer. Upon arrival found test wash load just ending and verified small amount of laundry quite wet. Found customer had selected casuals cycle. Explain to customer casual cycle will not spin at a high rate of speed as towels, bulky items, heavy duty or whites cycles. Recommend customer select one of these cycles for a higher spin speed which will extract more water requiring less dry time in the dryer. Also advise use of HE detergent only and very, very small amounts typically that of 1 teaspoon maximum. No mechanical issue found. No repair made or needed. Advise customer of one time courtesy no charge on a no defect. Sound service call visit. No charge to customer. Job complete."

Installed new pump and unit now functions as designed Complete

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

Cycled unit and found bad slider. Installed new slider. Retested unit passed all tests job completed.; used 1 W10734521 (Slider) from stock

Installed all parts listed no leaks working properly

Replaced thermistor and main control.

Replaced parts and tested unit job complete

Replaced all refrigerator and freezer light modules ok now

Removed and replaced main harness and main control at the same time. Tested unit. All tests good to 350 on bake and broil working normally. All tests good.

Installed new parts. Operation tested as designed. No gas leaks at time of service.

Removed and replaced board cam cap and actuator. Ran test. Now working as designed. Job complete

Found defective blower wheel. Fixed blower wheel. Tested unit and is working properly. Found dam vent informed client

Installed new drive hub and capacitor. Recalibrated and unit is working per design. Job complete

F9E1 error code. Found unit had a kinked drain hose. Removed kink and tested. Unit is working properly. Customer approves function at this time.

"Unit was tested with service test gave no issues and there was no error codes although did see some installation issues with Cx drain hose there where not using original one and the one that was there was extremely long and on the floor this would be Cx issue why she having problems, Cx will have to correct issue and fix drain hose, no issues with unit, job completed."

JB out 3/7/23. IVerified top 6 LED modules in RC non functional. Also FC LED non functional. Installed replacement LED module (W11601310) in FC restoring all LED modules functions.Tested operation with customer. No charge. JOB COMPLETE

Installed new sump. All functions now working as designed.

Replaced bulb and main board due to lite keeps blowing out.Tested ok

Found dishwasher not washing found bad sump pump replaced retested check out ok complete no dents or dings cause by tech.

"On arrival unit not draining, quoted Cx to clear filter, Cx approved. Cleared filter from front seal and tested, unit functions as designed."

Inspected unit found cutoff blown. Replaced and found heat element only half heat. Replaced and unit passed all tests. Job completed

Installed part magnetron giving small vibration rethighten retested check out ok complete no dents or dings cause by tech.

Installed springs

Installed transmission tested working properly

Checked out and ran diagnostics test. Ran cycle and found shipping rod was still in and causing major noise. Unit is now working as designed. Unit now washes filled and is working like it should. No noise. Test passed and working. Job completed

"Found the unit, not cooling, verify problem compressor not running, replace compressor, service valve, capacitor and relay, make a vacuum, charge refrigerant 48g R600a check compressor condenser and evaporator fan motors unit work normal ; used 1 W11506635 ( Service valve) from stock"

Installed new suspension rods and tested unit working as designed

Installed new keypad and knobs retested unit all tests passed pass. Job completed.

Found the gearcase leaking. Also valve not closing on the hot side. And capacitor not allowing motor to start.

Not cooling fresh food compartment. Unit is making ice. No air flow in ffc. Removed fan cover. Fan not spinning. Removed and replaced evap fan motor. Installed fan blade. Now working properly. Cx to wait 24 hours for proper temps. Job complete.

Replaced broken door glass. Testing door and is working properly.

"Upon arrival found unit with error codes F8E5 and F10E2, causing failure on the water valve and the vent. Erase the codes, retest the unit and water valve has a test according with the tech sheet, and the vent was passing the test to. This unit is working properly. Job complete."

Defrosted freezer evap. Removed and replaced evap fan and harness. Installed. Now working as designed Job complete

Found actuator arm stuck in agitation cycle. Installed new agitator. Operation tested as designed. Did not make the noise at time of service.

"Replaced defective parts, tested unit and is working properly"

Replaced open heater. Unit tests OK in diagnostic.

Unit is not leveled and is causing the cabinet to be off. The doors are off and not leveled. Leveled the fridge and door is not swing open like it did. Customer is going to shim the rear right side and unit should be better. Checked out and fridge is working as designed. Job completed.

"The unit is not powering on at all. The customer reports before the unit stopped working they will see LF, or different F5 error codes. Removed the console, units main control board is receiving proper voltage, voltage to the console (U.I.) checked fine. Noticed one of the inlet valves solenoid was cracked with traces of water leaking. The console assembly, and inlet water valves assembly need to be replaced, and per customer reports, the lid latch assembly as well.

Cycled unit and found all components test normal. Instructed customer on the use of recede and proper cycle selection To improve dry times. Unit is working as designed. Job completed.

Belt had snapped off motor causing error code installed new belt from truck stock Complete

Customer had the bail arm in the off position moved bail arm to on position

Unit needed a fan because the fan on the unit was making a grinding noise replaced part and tested unit job complete

Upon arrival installed new parts and retested. Cx drain hose and Reservoir was very clogged with food and gunk. Cleared hoses and retested with new pump. All ops test normal at this time. Unit operating as designed. Advised cx if problem persist he will need a plumber to clear out drain system under sink. Job complete

"This is not a recall totally different issue, water got frozen causing water not dispense when pressing lever. The ice was defrosted which fixed issue no further problems,job completed."

Tested found system empty charged tested working to spec

Found range front left burner with a start delay removed burner left to right retested check out ok complete no dents or dings cause by tech.

Installed new wheels and unit functions as designed complete

Cx stated they heard screeching removed agitator and found multiple coins removed and unit functions as designed Complete

"Replaced all led, unit functions as designed."

Installed new drive hub. Unit passed all tests. Re calibrated and job complete. Unit had small smell of oil. Maybe need gearcase if recalled for issues.

Removed and replaced gas valve and console tested all works good at this time.

Customer stated that unit is making noise during wash cycle. Checked unit for error codes no codes. Found customer had off-balance loads which were causing noise. Customer to load clothes is balanced as they can to avoid off bounds loads. Fixed loose wash plate remove coins from between wash plate.

Found unit with low refrigerant. Tried to pull excessive cap tube to replace drier. Cap tube fell off in hand. Called tech line to document. Non-repairable per WPL tech line. SR#7735882002 - Garrett

Found unit missing the bottom venting grill. Installed and tested. Unit is now working properly.

"Found top vent cover out of place, replaced cover and tested unit working as designed"

Found the valve leaking. I replaced the valve and ran a diagnostic cycle. All functions tested properly after repair. Job completed.

Replaced cam and belt. Unit tested ok

Customer complaint unit light button gets stuck. Still works but cx doesnt like that the button goes in more than the others. Cosmetic issue. Looked up panel. No longer available. No parts available to repair unit. Refer to manufacturer. Unit works but light button gets stuck inside unless you press again. Working. Fan works. Sounds are normal.

"Found faulty roller, replaced rollers, function tested unit, unit operating as designed. Job complete."

Arrived and Cx said it made ice once. Inspected unit and found ic tray was hung up on a cube of ice. Removed cube from tray and unit passed all harvest and fill tests. Unit is now working per design. Job complete

"CX states old unit compressor stopped working, has been serviced 3 times and hasnt worked in a month. Found refrigerator to be dismantled in CX homeLaid down floor protection, removed unit removed enclosure and out of home without incident.Brought new unit in and installed back into enclosure. Hooked up waterline and took quick pix of connection showing no leakLeveled unit doors are level / unit is cooling as designed job complete.

Installed control and tested. Unit heating normally

Removed and replaced glass and trim. Installed. Now working as designed. Job complete

Replaced fill valve due to leaking dispenser.Tested ok

Cx could not removed filter. Removed and Cx instruct on pulling and replacing filter. Showed to reset hold for 3 seconds then clears filter reset alarm. Cx ice clumpped up. Cx had not used ice for a few months. Cx instruct on ice clumping due to cx not using ice. Ice clumps are normal if cx is not using the ice for long periods of time. Removed ice and cleared now dispensing properly. Cx instruct on use and care. All ops normal. Unit is working as designed.

"Replaced the main control board, checked units ops, all units ops check fine. The unit is now working as designed."

"Installed ignitor sand tested, u it functions as designed."

"Got to the house had to take Customers back door, we had to take off both doors to both refrigerators. We took out the old unit installed the new unit new unit functions as designed Job complete the old unit had a bad dryer on it Multiple repairs on it as well job completed"

Cycled unit and found bad slider installed new slider from TRUCK STOCK and retested unit passed all tests at time of service. Job completed.; used 1 W10734521 (Slider) from stock

Replaced support rods per tech line.Tested ok

"Found defective rollers and pulley and belt replacement of parts, tested unit and is working properly used 1 4392065 (Dryer kit) from stock"

After replacing the reservoir the unit is no longer leaking and the unit is working just fine. All tested ok. Job completed.

"Uninstalled microwave and tested blower, blower working as designed. Reinstalled and tried to secured vent. Vent was bound and bent due to spacing of hole. Cx aware of situation. Taped venting. Unit functioning as designed."

Corrected the water dispenser housing. Found vibration at the evaporator cover. The panel was pushed back and when I moved it forward the vibration stopped. Unit quieter now