Found no problem with unit. Dishwasher meets factory specs

"Found no error codes stored, unit agitating as it should. Cx stated f2 e2 is intermittent. Called tech line they asked to have unit running on dedicated first and if issue reoccurs, to replace main board.Sr#7735411904"

"JB out 3/13/23. Customer states unit shakes and walk and walk away from the wall during spin cycle. Also unit ,Make a high pitch noise while filling with water.Found unit away from wall upon arrival. Tested unit in TOWELS cycle with Towels loaded into wash tub. Verified loud noise during fill portion of cycle. Installed replacement Cold) water inlet valve W11316256. Retested. No more noise.Moved washer back against wall (3 finger spacing from wall) and adjusted leveling feel. Locked leveling feet in place. Tested. DRAIN and SPIN cycle."

Installed central electric and inlet valve. Performed calibration. Operation tested as designed. No leaks.

"Fixed- used part from SP (4392067 dryer repair) found unit to be making a loud squeaking noise during any cycles - removed front panel and drum and found belt, rollers, pulley to be worn out from normal wear - removed bad ones and then installed new ones- reassembled drum and front panel tested unit, no squeaky noise, heating as designed- cx ok repair. ; used 1 4392067 (Dryer repair kit) from stock"

Cycled and found unit with broken thermistor in faulty motor on icemaker. Customer approved estimate. Removed and replaced icemaker. Re-tested it and unit passed All tests at the time of service. Job complete Icemaker

"Condenser coil were cleaned, compressor is running very hot and its not cooling at all so this is definitely an SSR.At this point because the costly repair consumer has declined to repair and will move on to buy a new unit. This ticket should be close."

I found the leak is coming from dispenser water lines into the door main harness and dripping right at the elbow.Consumer was informed if the situation and also about the door assembly not being produced anymore.

Removed old unit installed new unit tested new unit new unit worcking as designed Customer said old unit stopped worcking

Installed new filter and unit is now dispensing per design. Job completed

Due to customers unavailability. I was not able to deliver services. Gabby is aware of it and we will reschedule it as soon as customer call us back. NOTE: while I was at my next call consumer reached out to me and told me she was home. Ive stopped and addressed issue at hand.

Replaced bad motor tested unit is spinning with no noise

Motor is making popping noise. Replaced motor tested unit is spinning with no noise job complete

"Removed defective unit. Installed new unit, tested new unit, works as designed. Customer said unit wasnt heating up."

Instructed customer on how the door operates explained door does not have an assisted close. Raised the front high in order to have door close better. Unit operating as designed

Jammed ice maker with ice. Had it replaced

Installed new drier and compressor. Recharged with 5.3oz r134a. Unit was cooling as I was leaving. Cx to wait 24hrs before restocking.

Installed new thermistor. Instruct customer to allow 24 hours.

"Removed and replaced parts listed, tested ops unit working as designed"

"Do handle was loose found LooseScrew holding skin retighten skin screws, and retighten handle. Unit is now working as design at this time of service."

"Fixed- installed all new parts (cntrl elec, valve, dispenser cup, fascia) calibration test pass, auto test pass as well, no errors, no leaks- c. Ok repair"

Replaced missing bail armJob complete

Unit was working correctly when tech arrived No more water leaksNo part needed

Installed new door. All ops now checking okay.

Replaced ice bin and unit is now dispensing per design. Job complete.

"F5e1, f8e3, f0e7, cleared error codes and re programmed main control. Unit is now functioning with no issues and working as designed."

"Two separate issues. First issue I traced a short two main control control needs to be replaced. Second issue is that unit is leaking from underneath. Parts needed are no longer available for this unit, unit is over 25 years old."

15.42. Installed the new inner glass. Door ok

"Fixed- cx has a extended warranty look at pictures- found rollers, belt, pulley are worn out causing a loud squeaking noise during ashy cycles- removed bad ones and then installed new part (dryer repair kit) tested no squeaky noise, heating as designed- good air flow- cx ok repair"

"Replaced components ordered. Installed DW, restored power. Ran test check for operation. Unit is filling washing and draining."

Installed new tub bring him retested unit all tests pass. Job completed.

Replaced housing. Water filter can now be removed.company that installed fridge dropped and bent fridge and bent frame upon installation. Cx is going to call moving company to address irreparable damages.

"Installed water housing and hoses Cx supplied, tested, unit functions as designed."

Replaced open bake igniter tested after repair all ok.

Installed new UI retested unit passed all tests

"Because of a not sealing anymore issue, a new FF section doors seal has been replaced."

"Installed and secured new UI control panel, programmed unit to correct model, tested unit, unit is now operating properly as designed at this time of service, customer approved repairs"

JB out 3/11/23. Installed replacement RH hinge. Reassembled unit and reinstalled into cabinet installation. Tested operation. No water leaks. No charge to customer.JOB COMPLETE

"Installed control, heater, screws and sump. Tested, unit functions as designed. Bill out additional labor for new sump installation."

Replaced open bake igniter tested after repair all ok.

Replaced listed parts in order to fix loud grinding noise issue. Tested after repair all ok

Customer stated that the unit shakes a lot in the spin cycle. Found unit is on base which is causing off-balance loads per tech line previously was told units need to be on the ground or on base matched with machine. Tested all works good at this time.

Found several broken wires chewed up by mice which I reworked replaced by the drain pump Dishwasher ok

Replaced vent and control all tested good

JB out 3/11/23. Advised customer one year warranty has expired 1/1/2022 as provided by the GE Service Dispatch. Customer states that General Electric had replaced the refrigerator on 3/10/2022 but has no documentation for the product replacement. G.E. Service dispatch lists the date of purchase as 1/1/2022. Customer states the refrigerator does not cool and makes a snap sound repeatedly every 3-5 minutes. Upon arrival found refrigerant section cooling normally but freezer section is room temperature..unit was unplugged and defrosted prior to about 11:39 am today. Customer states no cooling and a snapor other unusual sound and then stopped cooling. Customer is unable to provide proof of replacement date at this time. Customer showed an email from Haier dated 3/4/2022 stating a replacement refrigerator has been ordered for delivery . Photo or email is attached in quick pic form Customer is requesting a product replacement and does not want repair service. Recommend customer contact General Electric to make product replacement request. No repair made today. Collected no money from customer.

Removed and replaced suspension and belt. Tested unit. All tests good.

"Customer concerns. Microwave keypad not responding. Upon arrival, i found control locked. I pressed 3 seconds to unlock. Microwave works as designed."

Found no water pressure at the inlet valve the house water valve very hard to turn on. Recommend replacing valve. Verified inlet valve is energized when the unit is started. Unit ok.

"Performed the vent test first with the vent hose on, test flap stood in place. Removed the vent hose and installed the vent test kit again, turned the dryer on and the flap came off and was held up against the lint filter housing indicating that their is a blockage within the venting, no blockage present in the vent hose from the dryer to the wall. Customer will need to have the vent professionally cleaned to ensure proper airflow.

Complete- cod- frozen fill tube causing water not to fill ice maker mold- dispenser motor is locked up- cx define repair at this time- will call office if they want to continue with repair.

Installed new wire harness and capacitor. Operation tested as designed. No leaks.

Customer stated that the unit shakes and makes noise on every cycle. Checked unit for error codes. No codes. Found fill hoses and drain hoses may be making noise from vibration. Ran unit through diagnostics and found unit is working to specs. Customer to secure fill lines and drain hose to avoid noises. Customer wanted to test a load. Ran small load washed and spun out no issues.

"Technical Service Pointer #: W11632927 Rev A Action Required: MandatoryRelease Date: August 2022Potential Causes: Run Capacitor, harness connections, or motor issue. Also belt slipped off from pulley/motor. Re-placed the belt. Unit kept displaying f7e1. Installed new capacitor. Performed calibration, initiated quick wash cycle. Operation tested as designed. No leaks."

Fridge needs new evap harness. Harness has been discontinued.

"Visual inspection suggests that the freezers door was left opened for a long while creating the frost up issue.Consumer has to go to airport so, instructions on what to do and expect were provided. No parts nor repairs are needed at this moment."

Removed and replaced Fraser evap motor . Retested it and it passed all tests at the time of servixce job complete

"Removed and replaced parts listed, performed maintenance cleaning, asked cx to have duct replaced to a harness duct system. Unit working ok"

"Found long fill codes stored in memory, tested unit found cold water valve failed has power will not cycle replaced valve all tested good ; used 1 W11210459 (Valve) from stock"

Installed icebox gasket kit and tested unit. Unit is working properly. Defrosted all built up ice. Customer approves function at this time.

Fixed- found capacitor to be making a loud buzzing sound causing unit not to start- removed bad one and then installed new pre Id (capacitor) calibration test pass- auto test pass- no leaks- unit now working as designed- cx ok repair

Cycled unit and found loose drain pump filter causing leak. Secured filter to drain pump and re-tested unit all tests pass. Job completed

Customer stated that the left door is lower than the right door. Found left door is missing the closer installed closer tested all works good at this time.

"Unit display off on arrival, reset unit and unit started to cool. Advised Cx to monitor unit, potential control issue. Could not duplicate. No charge to Cx."

"Lid strike broke. Installed new strike.

Unit not spinning. I found that the actuator was not engaged with cam. Removed and replaced actuator. Tested unit. All tests good. ; used 1 W10913953 (Actuator) from stock

"Installed cover, unit functions as designed"

Installed thermistor. All components tested normal. Instruct customer to allow 24 hrs.

Found unit leaking water during drain cycle. Found water backing out of stand pipe. Informed customer to call a plumber out and have them snake the standpipe. Customer approves function.

Cycled unit and found latch not installed properly. Reinstall the secured latch. Re-tested unit all test pass. Job completed.

"Customer concerns. Washer leaks sometimes, and vibrates during spin cycle. Installed suspension assembly, ran quick wash cycle. Operation tested as designed. Found no leaks at time of service."

"Failed drain pump has power will not run, replaced pump all tested good"

Lubricated rails and unit now working as designed.

"Removed and replaced compressor. Pulled vacuum, recharged system, inspected for leaks and found none . Unit is now cooling in both sections with no errors. Job comp

Found unit with venting error. Instructed customer to get a sweep venting. Venting came back blocked.

"Replaced the board and drain pump, calibrated the control board and pump. Ran diagnostics, diagnostics completed with no errors present. Unit is functioning as designed"

"As per customers request, all (5) gas knobs have been replaced."

Installed new belt and cleaned water valve filters. Re-tested unit all test pass. Job completed.

"Installed quoted parts, tested, unit regulating to temps.

Customer stated that u it stopped cooling but is now cooling also customer stated that the auger motor is not working. Customer is going to wait and see if unit stops cooling. Collected service call.

Customer stated that the unit is not making ice. Found ice maker jammed. Removed and replaced ice maker tested all works good at this time.

Within 30 days. I had started a load before leaving and that load went off balance and scared customer. I verified proper operation. Was just off balance. All tests good.

Arrived at cx home and was told dishwasher is working fine now.

JB out 3/11/23. Installed replacement HOUSING ASSEMBLY W11172234 asordeed. Reassembled unit and tested operation in BEDDING cycle.verified proper operation and NO WATER LEAKS found.No charge to customer.JOB COMPLETE

"JB out 3/11/23. customer states when icemaker valve opens to fill icemaker with water. It makes a very loud buzzing noise. Unable to verify valve operation during todays service visit. Listen to customers recording, which seemed to sound normal at the time. Customer also states the left-hand door sits lower than the right hand door, and the handles are uneven. adjusted left hand foot break to properly level cabinet, which raises the lower door. Doors are now 11. Recommend customer remove tow panel grill every three months for the life of a product in order to vacuum and brush clean the condenser coils. This will help maintain high energy efficiency levels. Icemaker will produce ice faster and hotter. Weather and refrigerator will last longer. No parts used. No charge to customer. Job complete."

For the second time replaced the doors both Bellow.

Customer stated that the unit will not power on. Found outlet is bad. Tested on different outlet unit works to specs. Fixed spray arm tested all works good at this time.

91 not draining. Found drain clogged. Removed top and used hose to clear debris. Ran cycle. No more issues. Cx approved job complete.

"Removed and replaced drain hose and clamp, tested ops no leaks unit working as designed."

"JB spoke with customer by telephone March 11, 2023 at approximately 2:30 PM. Customer states another service company, Oak Valley appliance was out several days ago and installed a replacement. Computer control board and unit is not working properly. Contacted SG in dispatch and verified. Customer needs to request. Oak Valley appliance to return to complete the repair on the product as they just replace the control a few days ago. Informed customer to contact Oak Valley appliance did not go no charge the customer."

Found washer not agitating. Installed new capacitor ( truck stock ). Operation tested as designed. ; used 1 W11395618 ( Capacitor) from stock

Removed and replaced motor unit now working as designed

"Found that the ui panel failed, installed the new ui and verified that the dishwasher is functioning. Unit is functioning as designed."

"Replaced lid strike. Belt slipping. Replaced belt. Locks/ unlocks, fills,agitates, drains,rinses, and spins properly at this time. Complete.; used 1 WPW10006384 (Belt) from stock"

Installed new parts. Operation tested as designed.

"JB out 3/11/23. Customer states while running water in kitchen sink water drains into dishwasher. Upon arrival verified improper installation and no air gap device used. Recommend customer install an air gap device as outlined in the supplied installation guide. If air gap device is not possible due to the granite countertop, run the dishwasher, drain hose with a high loop to prevent water from draining back into the dishwasher from the garbage disposer also found bottom spray arm disconnected. Instructed customer how to remove and reinstall bottom spray, arm and lock in place and recommend it be removed and the filter washed out from time to time. No parts used. No charge to customer."

"Unit in warranty with RAC- found freezer ice maker had fallen off - reattached ice maker, tighten screws- ice maker is now secured and should not fall off again. Cx ok repair"

"Remove and replace a compressor. Pulled vacuum, recharged system, inspected for leaks, and found none. Unit is not cooling in both sections. Job complete. Please bill sealed system."

Replaced faulty chute seal. Verified proper fit. Unit ok after repair.

Customer stated that the unit is not spinning. Found error code for actuator. Removed and replaced actuator and cam kit in stock. Different issue than previous call.

A new lid assembly has been installed and customers satisfaction was achieved.