We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Bakersfield, CA 93311
Aaron
Job Details:
12/02/2024
"Checked the unit this time cleared the control , unit started drain pump empty again , unit has a bad pressure switch and or stuck relay , ether way unit needs main board , est to replace the main board is $464.95 ; ordrng 1 W11608056 (Control asm)"
We serviced a
WHIRLPOOL OVEN
Model RBS305PDQ17
Near Moreno Valley, CA 92555
Kevin
Job Details:
12/02/2024
Unit giving F3E2 error for oven over temp. I tested temp sensor and found it way out of range. I removed and replaced sensor and tested. Unit now pre heated normal but then gave code later in bake. I tested relays on board and found that the bake relay is welded on board and thats what damaged sensor. Submitted for approval. ; rqstng P&A on 1 WP8302994 (cntrl-elec)
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC2
Near Moreno Valley, CA 92553
Kevin
Job Details:
12/02/2024
"Unit is not drying and making noise. I found that the blower wheel is stripped on motor shaft and motor, housing and blower wheel will need to be replaced together since its stripped. Ordering parts. ; rqstng P&A on 1 W11549461 (Motor) and 1 WP697772 (blower wheel) and 1 W11596046 (Seal) and 1 W10888146 (housing)"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Bakersfield, CA 93306
Brandon
Job Details:
12/02/2024
Units harness is severed at the drain pump. Lid is not locking either. ; ordrng 1 W11513248 (Lid latch) and 1 W11643701 (Lower harness)
We serviced a
KITCHENAID ICEMAKER
Model KUID508HPS01
Near Thousand Oaks, CA 91320
Ian Y
Job Details:
12/02/2024
Found unit full of water with display not turning on. plugged power from pump into wall fixture and machine insanely turned on. Unit has bad pump will be replacing. ; ordrng 1 1901A (Pump)
We serviced a
KITCHENAID KITCHEN
Model KDTM604KPS3
Near Agoura Hills, CA 91301
Ian Y
Job Details:
12/02/2024
Found dish rack assembly defective not allowing customer to adjust rack. Ordering rack and adjuster parts. ; ordrng 1 W11268090 (Left rack assembly) and 1 W11268086 (Right rack assembly) and 2 W11180605 (Clip adjuster arm)s
We serviced a
KITCHEN AID BUILT IN REFRIGE
Model KBSD702MPS00
Near La Cañada Flintridge, CA 91011
Ron H
Job Details:
12/02/2024
Tech was assigned as a helper;
We serviced a
JENN-AIR MW OVEN COMBO
Model JMW3430IL03
Near Malibu, CA 90265
Giovanni M
Job Details:
12/02/2024
SR#7740444251Customer is complaining that the unit will power off during night time. I called Tech Line because you didnt seem to be working just as designed. Tech Line believes that the user interface is the cause for all these problems. I let the customer know that the user interface is covered for five years . Ordering user interface for customer now.; ordrng 1 W11449431 (UI)
We serviced a
KITCHENAID DISHWASHER
Model KUDE60FXWH4
Near Malibu, CA 90265
Giovanni M
Job Details:
12/02/2024
CX was complaining that the units door wouldnt stay up. Upon diagnosis I found the spring to be faulty. Safty isnt coming this repair SR#7740394292; schdld next appmnt for 12/11 WED !
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Monrovia, CA 91016
Andy
Job Details:
12/02/2024
"Wrong part came out, needs harness with heater; ordrng 1 W11650662 (Heater)"
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Salida, CA 95368
Martin R
Job Details:
12/02/2024
Found suspension is bad causing tub to sit at angle allowing water to miss fill cup; ordrng 1 W11400156 (Damper)
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GFE28GYNKFS
Near Patterson, CA 95363
Manuel B
Job Details:
12/02/2024
Fridge not cooling.and water dispenser not getting any water nor making ice.reroute for part.call tech support file#14464650; ordrng 1 WR57X27527 (Duel water valve) and 2 WR86X37550 (Dye dryer)s and 1 W11506635 (Service valve)
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Patterson, CA 95363
Manuel B
Job Details:
12/02/2024
"Washer leaking from gear case.install Gear case,clutch,rotor,harness wire,slider. Nut spunner sis up broken from gear case.neec new nut spunner.reroute for part.; ordrng 1 W11551646 (Nut spunner)"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Delhi, CA 95315
Cruz
Job Details:
12/02/2024
Need work- found motor pulley to be broken/wobbly- found belt to be shredded- ordering parts for unit. ; ordrng 1 W11026785 (Motor) and 1 W11239857 (Belt)
We serviced a
WHIRLPOOL WASHER
Model CET9000GQ2
Near Merced, CA 95340
Cruz
Job Details:
12/02/2024
Need work- Aiden from whirlpool commercial laundry tech-support said to replace Cnrtl elec- coins are not registering- order part for unit. ; ordrng 1 W11282948 (Tech box assembly) and 1 W11282947 (Altas board)
We serviced a
KITCHENAID RANGE
Model KSGG700ESS2
Near Salida, CA 95368
Martin R
Job Details:
12/02/2024
Found ui and burner heads are bad ordering new ; ordrng 1 W11105615 (Ui) and 1 W11443577 (Burner kit) and 1 W11443594 (Burner kit)
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Ceres, CA 95307
Martin R
Job Details:
12/02/2024
Found Gearcase is leaking oil ordering new Gearcase ; ordrng 1 W11449841 (Gearcase)
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Oakdale, CA 95361
Martin R
Job Details:
12/02/2024
"Replaced Gearcase, lid lock and slide tested unit washer is filling agitating draining and spinning but is now not registering the bulk compartment need to replace bulk sensor component and main control ; ordrng 1 W11413407 (Drawer) and 1 W11419051 (Main control)"
We serviced a
UNKNOWN OVEN
Model AGR5835QDB
Near Bakersfield, CA 93307
Esteban S
Job Details:
12/02/2024
Unit requires control board. Control board not supplying power to igniter. Control board has been discontinued. Part no longer available. Job completed. ; saved tckt
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW0
Near El Monte, CA 91732
Andy
Job Details:
12/02/2024
"Unit makes noise on spin cycle found motor shield, damaged, causing noise also suspension rods week unit needs suspension rods and motor shield; ordrng 1 W11217817 (Suspension rods) and 1 WPW10550173 (Motor shield)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW
Near Los Angeles, CA 91406
Oscar L
Job Details:
12/02/2024
"Due to the way the gasket is crimped withe liner and insulation, I am recommending a full FF section door replacement.; ordrng 1 W11023679 (FF section full door)"
We serviced a
WHIRLPOOL WASHER
Model WFW75HEFW0
Near Los Angeles, CA 91352
Oscar L
Job Details:
12/02/2024
"As the pre diagnosed components wer replaced, the units controls came to be normally operational but, unit did not succeed after. And even when there are no errors anymore, unit keeps on advancing till the 17 minutes mark and enter some sort of standby mode. Called whirlpool to document and spoke with Kurt, whom after my explanation and a few more check points, recommended replacing the control unit. 7740401421; ordrng 1 W11201274 (Control unit)"
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Porterville, CA 93257
J.E.
Job Details:
12/02/2024
Cycled unit and found bad latch ordering part. ; ordrng 1 W11670519 (Latch)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ1
Near Los Angeles, CA 91311
Sean W
Job Details:
12/02/2024
"Ui displaying F9E2,F8E4 and F2E1, ran diagnostic cycle successfully but could hear motor and drain pump struggling to function,orderd new motor sump assembly and drain pump.; ordrng 1 W11460945 (Motor)"
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Bakersfield, CA 93313
Aaron
Job Details:
12/02/2024
"Needs 2 call count Check3d the unit , customer has a video showing it squealing, needs new gear case , hub nut , slider and agitator , ordered parts , needs 2 call count ; ordrng 1 W11449841 (Gear case) and 1 W11551646 (Hub nut) and 1 W11550891 (Agitator)"
We serviced a
WHIRLPOOL WASHER
Model WTW5500XW3
Near Los Angeles, CA 91311
Sean W
Job Details:
12/02/2024
Added gearcase and outer tub to invoice.; ordrng 1 W10324648 (Outer tub) and 1 W11454372 (Gearcase)
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Apple Valley, CA 92308
Cesar
Job Details:
12/02/2024
F5 E3 found broken harness to lock ; ordrng 1 W11449075 (Harness) and 1 W11682224 (Harness)
We serviced a
WHIRLPOOL DRYER
Model WGD5605MW0
Near Castaic, CA 91384
Felipe S
Job Details:
12/02/2024
"Upon arrival found unit with error code F6E1, this about UI miss communication. Check the unit and ui sometimes respond, after 5 minutes working, the ui stops to respond and show ERR on the screen. This unit will need new Ui and harness. Pop on pictures ; ordrng 1 W11583883 (UI) and 1 W11459337 (Harness)"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1835VWC
Near Castaic, CA 91384
Felipe S
Job Details:
12/02/2024
"Upon arrival found unit no working properly. Check the unit and found the control board is the one is bad, this because the unit dont work on any temperature settings except on the max cooling. This control board is the one is causing the failure. Will need new control board. ; ordrng 1 5304522330 (Control)"
We serviced a
MAYTAG WASHER
Model MVW7232HC0
Near Nipomo, CA 93444
Jack
Job Details:
12/02/2024
Customer stated striker is broken. Will not wash or go into any cycle. F0e3 f0e7 ran a calibration cycle ran dlmh cycle. Unit is now working as designed. Tested unit is a cycle and passed. Replaced striker with new. Job completed
We serviced a
WHIRLPOOL WASHER
Model WED7120HW2
Near Merced, CA 95348
Cruz
Job Details:
12/02/2024
"Fixed- found left door hinge to be slightly bent, causing grinding noise when opening/closing door, I then adjusted left hinge, tested no grinding noise- door is opening/closing as designed- cx ok repair"
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Oxnard, CA 93035
Isidro
Job Details:
12/02/2024
"F0e2 suds soap, f5e2 lock failure, loose door lock pin wire harness, I reinstalled and secured door latch wire harness, erased errors ran diagnostics unit is now spinning, locking and operating as designed at this time of service"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Santa Clarita, CA 91387
Felipe S
Job Details:
12/02/2024
"Upon arrival found unit with too much clothing, customer stated the unit is no getting the clothes ready for dryer. Inform the customer a big blanket plus some clothing is way too much for this unit, check the unit and found error code F0E3, this about the overload. Erase the codes and check the unit and found unit uneven, causing failure. Readjust the unit. Retest and now is working properly. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Bakersfield, CA 93309
Randy
Job Details:
12/02/2024
Unit keeps draining wont spin. Cx towels wet would not properly drain. Started drain and spin. Only light up three lights then done. . Lifted unit found leaking from the capacitorRemoved and replaced capacitor. Tested. Now working as designed ; used 1 W11395618 (Capacitor) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ01
Near Los Angeles, CA 91367
Ian Y
Job Details:
12/02/2024
"Found units drain line frozen. Defrosted, found the heater was not installed in the clips forcing the drain line to defrost. Installed the heater correctly and tested unit. Unit now functions as intended by manufacturer"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Lancaster, CA 93535
Samson O
Job Details:
12/02/2024
"Found unit stuck in spin mode, calibrate unit and test unit ok. No error or fault code. Cx should not wash heavy blankets because problem started with cx washing blankets. Unit test ok. Complete"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Thousand Oaks, CA 91362
Ian Y
Job Details:
12/02/2024
"Found bolt securing rotor motor backed out. Used new bolt I had on truck with loctite and secured motor properly. Tested, unit now performing as designed."
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Baldwin Park, CA 91706
Andy
Job Details:
12/02/2024
"Leaks, found door seal o; left side not installed correctly reinstalled and tested unit working properly no leaks"
We serviced a
WHIRLPOOL OVEN
Model WFG320M0MS0
Near Apple Valley, CA 92308
Cesar
Job Details:
12/02/2024
Found failed Ignitor ohm open all tested good ; used 1 W11176454 (Ignitor) from stock
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW1
Near Oxnard, CA 93033
Isidro
Job Details:
12/02/2024
"Unresponsive when pushing start, bad thermal fuse. I installed new thermal fuse and secured all wire harnesses, unit is now starting and heating as designed at this time of service ; used 1 WP3392519 (Thermal fuse) from stock"
We serviced a
MAYTAG DRYER
Model MGD4500MW1
Near Ventura, CA 93003
Kenneth
Job Details:
12/02/2024
Found unit not heating. Found thermal cutoff burned out. Replaced and tested. Unit is working properly. Informed customer to get house venting cleaned to keep from having further issues. ; used 1 W11050897 ( Cutoff) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW1
Near Livingston, CA 95334
Cruz
Job Details:
12/02/2024
Fixed- found error code f9e1 drain pump failure- removed bad one and then installed new one (drain pump) provided by the warranty company- calibration test pass- auto test pass- no leaks- no errors- cx ok repair
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Apple Valley, CA 92308
Cesar
Job Details:
12/02/2024
Found loose connection at junction box causing unit to loose power tighten connections all tested good
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Santa Paula, CA 93060
Isidro
Job Details:
12/02/2024
"Ran diagnostics test, found a stripped hub not spinning, Installed new hub kit from stock parts, calibrated unit and its now spinning and operating as designed, cx approved repair and service ; used 1 W10528947 (Hub kit) from stock"
We serviced a
WHIRLPOOL WASHER
Model WTW7500GC2
Near Oxnard, CA 93035
Isidro
Job Details:
12/02/2024
"Ran diagnostics found errors f5e3, f3e2, f0e4, f0e3, door latch assembly was stuck closed. I repaired door latch and reinstalled and secured wire harness erased errors tested unit and its apparently operating as designed at this time of service., I was unable to call tech line due to time"
We serviced a
WHIRLPOOL WASHER
Model WFW9500TW01
Near Los Angeles, CA 91311
Sean W
Job Details:
12/02/2024
"Ui displaying F61 error code indicating ui and our control board communication issue,due to repair costing more than washer,Cx is going to replace unit, collected service fee via card through iWallet."
We serviced a
MAYTAG DRYER
Model MGD5630HC3
Near Los Angeles, CA 91304
Sean W
Job Details:
12/02/2024
"Dryer not heating due to shattered igniter,replaced igniter,flame now igniting and dryer working properly.; used 1 279311 (Igniter) from stock"
We serviced a
MAYTAG WASHER
Model MVWB765FC1
Near Fresno, CA 93706
Timothy
Job Details:
12/02/2024
Unit had a loose auger . Found the bolt had backed out. Reset and tested . Unit checks ok.
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW2
Near Los Angeles, CA 91307
Sean W
Job Details:
12/02/2024
"Replaced worn rollers and pulley,dryer no longer making irregular noise and is working properly."
We serviced a
MAYTAG WASHER
Model MVW6500MW0
Near Port Hueneme, CA 93041
Isidro
Job Details:
12/02/2024
"When starting any cycle unit would go straight to done, bad capacitor, I installed new capacitor from stock unit is now advancing and spinning properly as designed at this time of service ; used 1 W11395618 (Capacitor) from stock"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Oxnard, CA 93033
Isidro
Job Details:
12/02/2024
"F9e1 long drain , found a broken wire harness to the drain pump. I installed new lower wire harness, unit is now draining and operating as designed, cx approved repair and service"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRSC703HPS00
Near West Covina, CA 91791
Andy
Job Details:
12/02/2024
"Leaks , replaced connecter and tested unit working properly"
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC3
Near Hesperia, CA 92345
Cesar
Job Details:
12/02/2024
On sensor cycle unit Ill run without heat no codes found in system per customer if they unplug the unit and plug it back in resetting it it will start to heat. Replaced control
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Perris, CA 92570
Kevin
Job Details:
12/02/2024
Unit making noise during spin. Found noise from underneath. Removed and replaced slider. All tests good.
We serviced a
MAYTAG WASHER
Model MVW6500MW0
Near Oxnard, CA 93030
Isidro
Job Details:
12/02/2024
"Customer states unit was trying to drain even when no water was in it. I power reset the control board by disconnecting, reconnected and ran diagnostics test no errors unit is now operating and draining as designed"
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW
Near Santa Maria, CA 93458
George
Job Details:
11/27/2024
Found washer not draining found torn harness replaced retest ok complete
We serviced a
WHIRLPOOL ELECTRIC RANGE
Model WFE301LVS0
Near Thousand Oaks, CA 91360
Richard R
Job Details:
11/27/2024
"On arrival in Inspected unit. Customer stated that when the oven was igniting order on that the unit would get very hot. I did explain to her that the glass can get up to a couple hundred degrees in it to keep your hands away from it and do not touch it, and that the unit vents from the top of the blowing out hot air, which is normal, but the unit did not seem to be heating correctly during my inspection I found a loose connection to the bake element, was able to repair it and clamp it down and re-tested unit unit is not heating as intended. All ops are normal job complete."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS2
Near Calabasas, CA 91302
Giovanni M
Job Details:
11/27/2024
CX was complaining that the unit wouldnt work. Found unit leaking from. The brass fitting on the water valve. Let CX know they need to replace that. I put purmer gum on it in the mean time for them.
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Lebec, CA 93243
Felipe S
Job Details:
11/27/2024
"Upon arrival found unit with error code F8E1, this about long fill. Check the unit and waters valves are working properly. Check the unit for the customer complaint about shaking too much, and found the front right shocks absorber a little bent causing the failure. Replace all 4 of those shocks absorbers, retest the unit and now is working properly. Job complete"
We serviced a
MAYTAG WASHER
Model MVWC465HW2
Near Santa Maria, CA 93458
George
Job Details:
11/27/2024
Found washer not turning replaced actuator tested check out ok complete.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Manteca, CA 95337
William
Job Details:
11/27/2024
"Replaced lower wire harness,ran self diagnostic cycle, unit operating as designed."
We serviced a
MAYTAG DRYER
Model MGDB835DW4
Near Fresno, CA 93722
Timothy
Job Details:
11/27/2024
Installed thermostat fix and TCO tested working properly
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Fillmore, CA 93015
Ian Y
Job Details:
11/27/2024
"Removed and replaced units valve assembly. Tested, unit now filling up with water properly."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Patterson, CA 95363
Manuel B
Job Details:
11/27/2024
"Dishwasher not working wires to pressure switch not connected,reconnect pressure switch wires.test diagnostic cycle all pass ok."
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Firebaugh, CA 93622
David C
Job Details:
11/27/2024
Replaced lower wire harness tested u it unit working as designed
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Los Banos, CA 93635
David C
Job Details:
11/27/2024
Found loose connection to control re connected tested unit unit working as designed
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Bakersfield, CA 93306
James
Job Details:
11/27/2024
Uninstalled unit and replaced broken hinge. Spring clip had failed. Door now working as intended.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Tracy, CA 95376
William
Job Details:
11/27/2024
"Replaced lower wire harness, ran self diagnostic cycle, unit operating as designed."
We serviced a
KITCHENAID MICROWAVE
Model KEMS379BBL01
Near Bakersfield, CA 93304
Randy
Job Details:
11/27/2024
Cx signed waiver to move appliance. Removed and replaced inverter board and magnetron. Unit now working as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Malibu, CA 90265
Giovanni M
Job Details:
11/27/2024
"I replaced the reservoir, valve and cap. Unit is working as designed at this time."
We serviced a
WHIRLPOOL WALL OVEN
Model WOS51EC0HS02
Near Bakersfield, CA 93314
Aaron
Job Details:
11/27/2024
"Checked the unit oven controls not recognize some of the touch controls , replaced the console tested ops ok now at this time"
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model PVD28BYNCFS
Near Ridgecrest, CA 93555
Brandon
Job Details:
11/27/2024
A part of the units harness was charred and not making good contact with the power board. Cx had the part of the harness that I needed. I used it to complete the repair. Unit is now fully operational.
We serviced a
WHIRLPOOL UNV
Model MVW4505MW
Near Baldwin Park, CA 91706
Andy
Job Details:
11/27/2024
"Lid not staying locked, replaced switch and tested unit working fine"
We serviced a
WHIRLPOOL FREEZER
Model WRF767SDHZ04
Near Colton, CA 92324
Francisco
Job Details:
11/27/2024
"Removed and replaced parts listed , vacuumed and re charge up to specs. No leaks nor damage by tech Cx approved before departure. Asked him to allow 24 hrs for normal temps and ops."
We serviced a
WHIRLPOOL REFRGERATOR
Model WRS321SDHZ11
Near Los Angeles, CA 91606
Tim B
Job Details:
11/27/2024
Metal bracket holding compressor fan was rattling. Fixed bracket and unit not rattling.
We serviced a
WHIRLPOOL DRYER
Model WED5605MC0
Near Fresno, CA 93722
Joe P
Job Details:
11/27/2024
"Installed control board, tested unit working to manufacture specifications. Heating and not shutting off. Job complete"
We serviced a
WHIRLPOOL DRYER
Model WGD7500GW0
Near Westlake Village, CA 91362
Richard R
Job Details:
11/27/2024
"Phone Rible inspected unit and found unit with worn out idler, pulley, bearing and one wheel bearing was out replaced all four wheels idol or pulley wheel and about re-tested unit unit no longer making a squealing noise job complete"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Calimesa, CA 92320
Rod
Job Details:
11/27/2024
Wont operate product.Control would not continue to supply voltage Intermittent contact with motor. Replaced defective controldesigned operation appears to have been restored.
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Merced, CA 95348
Cruz
Job Details:
11/27/2024
Fixed- installed new part (lower harness) calibration test pass- auto test pass- no leaks- no errors- cx ok repair
We serviced a
KITCHEN AID DISHWASHER
Model KDTM604KPS0
Near Riverside, CA 92508
Robert U.
Job Details:
11/27/2024
After replacing all parts ordered the unit is now able to go through a diagnostic cycle without shutting down prematurely. All functions restored and working properly. No error codes stored and all tested ok. Job com
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB08
Near Bakersfield, CA 93312
Aaron
Job Details:
11/27/2024
"Replaced the ice maker , tested unit filled up with water , ops ok now at this time allow 3 days to fill ice bin up without use"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Winton, CA 95388
Cruz
Job Details:
11/27/2024
"Fixed- installed new parts (ice maker, sealer) ice maker test pass- no leaks- cx ok repair"
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Hesperia, CA 92345
Brian G
Job Details:
11/27/2024
Removed and replaced main control. Ran diagnostics. All OK
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323AW9
Near Wasco, CA 93280
Esteban S
Job Details:
11/27/2024
Valve was removed and replaced. G
We serviced a
GENERAL ELECTRIC WASHER
Model GTW585BSV2WD
Near Palmdale, CA 93552
Jonathan B.
Job Details:
11/27/2024
JB out 11/27/24.Our arrival time was tub filled with water and clothing. Unit was found to be unplugged from electrical power supply. Plugged unit into power outlet and unit immediately went to emergency pump out of the drain. Drain pump is not operating. Manually drained full tub of water out. Removed and replaced green pump assembly with new pump part number WHQ3X28418. reassembled heated and tested operation in normal wash cycle.Verified correct water fill and agitation operation. canceled wash cycle.Selected a drain and spin cycle. Observed water properly drain from wash tub and unit did engage in spin function as designed. No charge to customer John.
We serviced a
MAYTAG DISHWASHER
Model MDTS4224PZ0
Near Loma Linda, CA 92354
Rod
Job Details:
11/27/2024
"Returned, replaced defective pump/motor assembly .as designed operation returned with no leaks"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near San Miguel, CA 93451
Leo R
Job Details:
11/27/2024
"Replace motor, capacitor, harness, splotch and actuator, tested unit, recalibrated it and it is now working properly,Job complete."
We serviced a
MAYTAG WASHER
Model MVW6200KW1
Near Los Banos, CA 93635
David C
Job Details:
11/27/2024
Replaced wire harness tested unit working as designed
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Moreno Valley, CA 92557
Kevin
Job Details:
11/27/2024
Removed and replaced actuator and belt and unit is now working as designed. All tests good.
We serviced a
KITCHENAID OVEN
Model KSGG700ESS7
Near Riverside, CA 92506
Robert U.
Job Details:
11/27/2024
After replacing the main control and the regulator the unit was still not lighting the bake or broil. I then checked the wires and found a pinched wire. I repaired the wire and that took care of the issue. Both bake and broil are now functioning. All tested ok. Job completed.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ2
Near Tracy, CA 95376
William
Job Details:
11/27/2024
"Replaced wash pump/motor, ran self diagnostic cycle, unit operating as designed"
We serviced a
MAYTAG DRYER
Model MGDE500VW2
Near Frazier Park, CA 93225
Felipe S
Job Details:
11/27/2024
"Install the new repair kit, blower, motor and seal on the unit. Retest the unit and now is working properly. Job complete"
We serviced a
WHIRLPOOL RANGE
Model WFE975H0HZ5
Near Los Banos, CA 93635
David C
Job Details:
11/27/2024
Replaced wire harness tested unit working as designed
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Arvin, CA 93203
Aaron
Job Details:
11/27/2024
"Checked the unit , replaced the ui board tested ops ok now at this time"
We serviced a
MAYTAG WASHER
Model MVW5430MW2
Near Ridgecrest, CA 93555
Brandon
Job Details:
11/27/2024
Installed new lid latch and tested. Unit is now operating normally again.
We serviced a
WHIRLPOOL ICE MACHINE
Model KUIX535HPA01
Near Altadena, CA 91001
Oscar L
Job Details:
11/27/2024
A new grid cutter was installed and consumer was informed and asked to allow at least 24 hours for normal operation to resume.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFG2353AF3
Near El Monte, CA 91732
Andy
Job Details:
11/27/2024
"No display on boards, replaced boards and tested unit working properly"
We serviced a
KITCHEN AID DISHWASHER
Model KDTM404KPS0
Near Riverside, CA 92506
Robert U.
Job Details:
11/27/2024
After replacing all parts listed the unit is now able to spray water around correctly and I checked for leaks. No leaks found and the unit was able to run an entire diagnostic cycle without any issues. All functions restored and job completed.
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US6B
Near West Hollywood, CA 90046
Tim B
Job Details:
11/27/2024
Replaced water inlet valve and tested. Unit functions as normal. Water line installed by landlord was correct but water doesnt turn off all the way. Was able to work around it but just wanted to notate.
We serviced a
WHIRLPOOL DRYER
Model WGD5010LW3
Near Moreno Valley, CA 92557
Kevin
Job Details:
11/27/2024
Unit not heating. Found open thermal fuse. Removed and replaced thermal fuse. Instructed customer to call to have venting cleaned since fuse was open.