Near Taft, CA 93268
Dane
Job Details:
01/17/2020
REFRIGERATOR GENERAL ELECTRIC GFE29HGDABB
On arrival freshmen compartment was not cooling. Fresher compartment was not cooling because the fan was not turning. Unit needs new fan; saved tckt
Near Hanford, CA 93230
Enrique
Job Details:
01/17/2020
REFRIGERATOR FRIGIDAIRE FFHT2032TP1
Inspected Frigidaire refrigerator . Both compartments not cooling . Shorted start device . Installed new start device . All functions tested normal . No leaks .
Near Bakersfield, CA 93314
Jim
Job Details:
01/17/2020
WASHER WHIRLPOOL WFW6620HW0
Installed deflector and drawer. Unit tested ok
Near Shaver Lake, CA 93664
Jonathan
Job Details:
01/17/2020
BUILT- IN MICROW GE PEB7227SLSS
Found switch and lever bad replaced tested working to spec
Near Clovis, CA 93619
Jonathan
Job Details:
01/17/2020
WASHER ELECTROLUX EFLS627UIW0
Found bellow leaking tested working to spec no leaks
Near Los Angeles, CA 91304
Danny
Job Details:
01/17/2020
RESIDENTIAL REFR WHIRLPOOL WRS325FDAM02
"Unit is not cooling properly Found condenser full of lint and blocked Cleaned condenser and cleared drain tube Reinstall unit and power up and compressor kicked on and started to cool,Advised client shelves are not covered by extended warranty Advised client to call whirlpool customer service If client calls back she will need ; ordrng 1 WPW10276341 (shelf-glas) and 1 WPW10276348 (shelf-glas)"
Near Clovis, CA 93611
Jonathan
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL WRX735SDHZ01
Installed plastic piece tested working to spec
Near Fresno, CA 93720
Jonathan
Job Details:
01/17/2020
COOK TOP GE MODEL
No model no serial on unit unable to find parts needs right front burner need to collect for service call
Near Fillmore, CA 93015
Aaron
Job Details:
01/17/2020
DRYER WHIRLPOOL WED7500GW0
"Replaced the bulk heads , rear was missing 5 screws and caused the bulkhead to sag and be out of alignment , install crew had to put in a side vent , my thoughts is they might have thought they could access from the rear then didn’t get it back together correct and causing this whole problem , now the unit I put back together correct and heat ok at this time"
Near Bakersfield, CA 93304
Dane
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW4955HW1
Customer was under the impression that even though unit was out of warranty the manufacture was still going to pay for it. Told customer they need to call manufacture and get a concession
Near Fresno, CA 93720
Timothy
Job Details:
01/17/2020
STOVE WHIRLPOOL WEC310SPFS3
Unit is now in building 27 apt #143. Unit needs a new burner kit.; rqstng P&A on 1 W11371990 (BURNER KIT.)
Near Los Angeles, CA 91344
Raymond
Job Details:
01/17/2020
WASHER WHIRLPOOL MHW8200FW0
"Upon arrival cx states that unit is staining clothes. Contacted Kurt SR 7726729890. Unit does not produce stains but can transfer or retain stains. Cx pulled load they were washing on arrival and load was overloaded, washing improperly. Instructed cx on proper use and care. No issues found no codes. Collected 115 SC."
Near Bakersfield, CA 93307
Dane
Job Details:
01/17/2020
WASHER MAYTAG MVWB766FW
Removed and replaced clutch gear case and agitator and tested unit. Unit functions normal now
Near Los Angeles, CA 91316
Randy
Job Details:
01/17/2020
WASHER WHIRLPOOL GHW9100LW
Found not starting either board or needs latch scheduled for Tuesday ordering latch. ; ordrng 1 WP8182634 (latch)
Near El Monte, CA 91732
Stephen
Job Details:
01/17/2020
DRYER - GAS AMANA NGD4600YQ0
"Replaced motor, support rollers, idler, & belt. Tumbling and heating properly at this time. Instructed customer NOT to use extension cord, to call electrician. Complete."
Near Los Angeles, CA 91335
Randy
Job Details:
01/17/2020
DISHWASHER WHIRLPOOL WDF330PAHS3
Found not drying dishes. Cx complaint left over water. Unit clogged at stand pipe. Cleared drain. Now runs but wash motor won’t go through. Needs new wash motor. ; ordrng 1 W11025157 (pump&motor)
Near Phelan, CA 92371
Cesar
Job Details:
01/17/2020
WASH/DRY COMBO SPEEDQUEEN ATEE9AGP173TW01
Replaced pump tested unit all tested good
Near Castaic, CA 91384
Randy
Job Details:
01/17/2020
DISHWASHER WHIRLPOOL KDFE104DSS5
"4-3, 7-1 ,2-1.Found unit with multiple error codes. Unit has error with heater shutting off. Cc following instructions on running hot water before hand. Ran diagnostics Unit will fail per error codes. Will need the boards replacement.Ordering boards and thermostat ; ordrng 1 W11105848 (console) and 1 W11305293 (cntrl-elec) and 1 WPW10195091 (thermostat)"
Near Los Angeles, CA 91304
Danny
Job Details:
01/17/2020
OVEN WHIRLPOOL KODE300ESS01
Not heating properly Found faulty sensorsReplaced sensor and power unit up and test oven and unit is now reaching properly Advised client to pre heat oven 25-30 mins
Near Stevenson Ranch, CA 91381
Raymond
Job Details:
01/17/2020
DISHWASHER KITCHENAID KDTE204GPS0
Upon arrival cx states unit not drying or washing dishes. Found fault codes for motor but motor new. No notes showing unit was placed through service cycle for recalibration. Recalibrated unit. Will follow up with cx on Thursday.; saved tckt
Near Paso Robles, CA 93446
Tom
Job Details:
01/17/2020
DISHWASHER FRIGIDAIRE FGID2479SF
"Ran unit, found unit fills with water, water supply good, Recirculation pump good, drain good, heating good, spray good, found UI not responding consistently, not able to select cycles, unable to cancel cycles, responds like buttons are stuck, order Control Board, UI, and Door Lock Assembly.Control Board - (117499430)User Interface - (117512430)Door Lock - (111315040)NOTE - PART OUT OF STOCK, RESCHEDULE CUSTOMER ON PAET AND TIME AVAILABILITY; ordrng 1 111315040 (door lock) and 1 117499430 (CONTROL ASSEMBLY) and 1 117512430 (CONTROL PANEL)"
Near San Dimas, CA 91773
Andy
Job Details:
01/17/2020
WASHER WHIRLPOOL WFW8540FW1
"Found error, replaced pressure switch tested unit working properly ; used 1 WPW10448876 (ANALOG PRESSURE SWITCH) from stock"
Near Fresno, CA 93720
Timothy
Job Details:
01/17/2020
RANGE WHIRLPOOL WFE505W0HS1
Installed control. Tested unit. Unit checks ok.
Near Los Angeles, CA 90272
Isidore
Job Details:
01/17/2020
DOUBLE WALL OVEN KITCHENAID KEBC278KSS02
"Found no 240volts ac, L1 ok L2 open or shorted getting 3-80 volt ac at times(should be 240 Vac). Needs electrician to correct electrical. May need oven cavity thermostat WP9759242 68.79 also customer to call back if needed. Note control fuse bypassed by customer NLA"
Near Los Angeles, CA 91401
John
Job Details:
01/17/2020
OVEN KITCHENAID KEBU208SSS02
"The lower oven has no convection fan motors, the appliance manager is most likely the issue. The temperatures inside the upper oven possibly not recovering due to the main control or the thermistor or the bake element. Customer will look into buying a new oven"
Near Bakersfield, CA 93314
Andrew
Job Details:
01/17/2020
VENT HOOD WHIRLPOOL WVW75UC6DS2
Customer said that Unit was crooked and dripping oil down the back wall. Checked unit and installation of vent hood is incorrect. Unit is not level and slants to the left. It’s her vent hood will have to come down and be reinstalled and leveled properly informed customer that this is something that needs to be done by the insulation company in the manufacture of the home. This is a major installation issue not a minor one but unit is working properly
Near Lake Isabella, CA 93240
Jim
Job Details:
01/17/2020
WASHER GENERAL ELECTRIC HTWP1400F2WW
"Replaced tub, motor, trans tube and seal."
Near Shandon, CA 93461
Tom
Job Details:
01/17/2020
WASHER MAYTAG MVWC565FW1
"Entered diagnostics, found error code F8E1, customer states that drain is fine, not filling, diagnostic tests show water flow good, agitate good, drain good, spin good, water supply to hot valve closed, opened water supply to hot valve, both valves operational, check okay. No damage to unit or home from tech, job complete."
Near Bakersfield, CA 93301
Jim
Job Details:
01/17/2020
DRYER WHIRLPOOL NGD4655EW2
Installed drive assembly kit. Unit tested ok
Near Santa Margarita, CA 93453
Tom
Job Details:
01/17/2020
WASHER FRIGIDAIRE FFLE2022MW2
"Entered diagnostics, error code E53, low voltage to Control Board. Voltage check at Control Board shows 120VAC to board. In diagnostics all components activate. According to Frigidaire, continuity checks of Control Board and Lid Lock checked, continuity good, attempted to replace Lid Lock shows no change. Continuity check of all wire harness shows good continuity, no shorts to ground found. Any attempt to start unit in normal operation produces same result, even after Hard Reset of Control Board. Frigidaire recommends replacing Control Board, 3 Control Boards attempted, informing customer.Customer requesting refund, unit not operational, tech requesting refund for customer satisfaction, customer will contact HQ. Job closed."
Near Clovis, CA 93619
Jonathan
Job Details:
01/17/2020
REFRIGERATOR FRIGIDAIRE FFHT1832TP0
Unit is sitting on carpet no room to work customer will call when unit is moved; saved tckt
Near Agoura Hills, CA 91301
Joe
Job Details:
01/17/2020
DISHWASHER KITCHENAID KDTM354DSS5
Replaced boards unit is now functioning as designed. Job complete.
Near Arroyo Grande, CA 93420
George
Job Details:
01/17/2020
WASHER MAYTAG MVWC416FW
Installed parts tested check out ok complete. No dents or dings cause by tech.
Near Oxnard, CA 93030
Joe
Job Details:
01/17/2020
WASHER WHIRLPOOL WFW92HEFC0
Unit had a sock stuck in the drain pump which only took me a few seconds to lean machine back and pull out. Only charging service call.
Near Camarillo, CA 93010
Joe
Job Details:
01/17/2020
WASHER MAYTAG MVWB835DW4
Replaced control and ui unit is now functioning as designed. Job complete.
Near Clovis, CA 93611
Jonathan
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL WRX988SIBM03
Installed adapter tested working to spec
Near Santa Ynez, CA 93460
James
Job Details:
01/17/2020
WASHER WHIRLPOOL WFW8620HC1
Unit has error for water valve failure and long drain. Also found over suds error and off balance load. Ordering new water valve and drain pump. ; ordrng 1 W11316255 (valve) and 1 W11316256 (valve) and 1 W11316609 (pump-water)
Near Grover Beach, CA 93433
George
Job Details:
01/17/2020
FREEZER WHIRLPOOL WRS588FIHW
Found refrigerator door not lining up found low spot on back right side customer instruct need to get a handy man to chim refrigerator for better door lining complete. No dents or dings cause by tech.
Near Bakersfield, CA 93305
Patrick
Job Details:
01/17/2020
WASHER WHIRLPOOL GSQ9611KQ2
Customer to call after Christmas. No money to pay for job 189.61 is the quote ; saved tckt
Near Pismo Beach, CA 93449
George
Job Details:
01/17/2020
DISHWASHER KITCHENAID KDTE254ESS2
Installed part tested check out ok complete . No dents or dings cause by tech.
Near Bakersfield, CA 93305
Patrick
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW4816FW
Found the unit not filling properly. Ch3dked errors. Valve error. Hot solenoid doesn’t work properly ; ordrng 1 W11210459 (valve)
Near San Luis Obispo, CA 93405
George
Job Details:
01/17/2020
DISHWASHER KITCHENAID KUDS30IXSS4
Installed part tested check out ok complete. No dents or dings cause by tech.
Near Los Angeles, CA 91436
Isidore
Job Details:
01/17/2020
RANGE HOOD JENN-AIR JXW8736DS00
"Removed top vent cover panel, old control user interface and installed new control interface, reinstalled top panel. Test operation ok at this time"
Near Fresno, CA 93720
Timothy
Job Details:
01/17/2020
RANGE WHIRLPOOL WEC310S0FS3
Installed burner kit. Tested operation. Instructed tenant on usage and left the instruction pamphlet with them.
Near Los Angeles, CA 91436
Isidore
Job Details:
01/17/2020
DISHWASHER KITCHENAID KDTE254ESS2
"Removed old upper rack adjusters and installed new dishwasher upper rack adjusters, test operation ok at this time."
Near San Luis Obispo, CA 93401
George
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW7500GW2
Found control board not communicating need to replace lock control board and display ok to order.; ordrng 1 W10861642 (latch) and 1 W11130237 (COUNCIL) and 1 W11130238 (BOARD)
Near Hanford, CA 93230
Enrique
Job Details:
01/17/2020
WASHER WHIRLPOOL WFW92HEFW0
"Inspected whirlpool front load washer . Customer concerns , displaying f1e1 error code ( shorted ACU . Installed control and water level switch . Retested it . All functions tested normal . No leaks ."
Near Hanford, CA 93230
Enrique
Job Details:
01/17/2020
REFRIGERATOR FRIGIDAIRE LGHB2869TF
"Inspected Frigidaire refrigerator . Freezing the food in RC . Installed control board , air tower and sensor . All functions tested normal at time of service . No leaks ."
Near Santa Maria, CA 93454
James
Job Details:
01/17/2020
REFRIGERATOR FRIGIDAIRE FFHT2032TP
Found unit with icing in airways from freezer. Fan in freezer weak from possible ice damage. Also ordering new cover assembly as foam insulation to downward air path missing and plastic cracked. ; ordrng 1 242077705 (MOTOR) and 1 242294705 (COVER ASSEMBLY)
Near Oxnard, CA 93033
Hector Zuleta
Job Details:
01/17/2020
DRYER WHIRLPOOL MCG8000AWW
Customer is complaining of dryer not running. I checked the unit and broken belt and worn out Idler pulley. Allow (2) counts for this repair.; ordrng 1 WP31001535 (pulley- mo) and 1 WP31001710 (idler arm)
Near Bakersfield, CA 93306
Patrick
Job Details:
01/17/2020
OVEN WHIRLPOOL FGP305KW4
"Found the units oven not working. Ignitor high amp draw. Removed and replaced from stock. Tested unit. All ops checked good ; used 1 12400035 (IGNITER,OVEN) from stock"
Near Bakersfield, CA 93305
Patrick
Job Details:
01/17/2020
COOKTOP WHIRLPOOL KECC667BSS
Found a loose connection at the ui. Doesn’t always respond. Secured connection to ui tested unit. All ops checked good
Near Santa Clarita, CA 91354
Andrew
Job Details:
01/17/2020
REFRIGERATOR KITCHENAID KRFC704FPS03
"Called techline said that an 1/8th gap is normally and can be caused by gasket being thicker on one side. Tried putting rolled paper towel behind gasket to force gasket to expand, so doors would line up properly and once gasket reformed after a few weeks would remove rolled paper. Informed Cx that door gasket is compressed and I could replace gasket but that may not resolve issue. MM heated heated Gasket and tried to reform gasket. Informed Cx that over time gasket on feet door would compress and doors would be even. Cx stated he will call pacific sales and have unit replaced. Techline used previous file number."
Near Coarsegold, CA 93614
Kenneth
Job Details:
01/17/2020
WASHER GENERAL ELECTRIC GFW430SSM1WW
Found unit not Turning. Making a loud slapping noise. Found belt had slipped off pulley and wrapped around motor pulley so everytime unit tried to spin. Unit would slap belt on the inside of washer. Mangled belt. Ordering new belt. Rescheduled customer for tuesday 12-31-19; ordrng 1 WH08X10050 (Belt)
Near Nipomo, CA 93444
George
Job Details:
01/17/2020
WASHER MAYTAG MVWB865GW0
Installed part tested check out ok complete. No dents or dings cause by tech.
Near West Covina, CA 91791
Andy
Job Details:
01/17/2020
WASHER MAYTAG MVWC565FW2
"Unit making a noise, found missing screw on belt shield causing shield to hit belt making a rubber noise. installed screw and tested unit working properly, found no other noises unit working as designed"
Near Fresno, CA 93704
Irvin
Job Details:
01/17/2020
RANGE WHIRLPOOL WEE750H0HZ0
The oven control is not operation. Hourglass displayed only. Not responsive. ; ordrng 1 W10854344 (cntrl-elec) and 1 W10868153 (cntrl-elec)
Near Oxnard, CA 93036
Hector Zuleta
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW8500DC5
"Customer was complaining of broken Lid. I checked the unit and I found a damaged lid and hinges. Replaced Lid (W111023747), Hinge (W10861714), and Hinge (W11023747). Tested ok."
Near Fresno, CA 93701
Irvin
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL WRT111SFDM04
"The unit is cooling sporadically. The defrost timer will not terminate. Just keep going on and off. Replacing control. ; ordrng 1 4388931 (timer,defrost adapt) and 1 W11269204 (contrl-box)"
Near Bakersfield, CA 93312
Jim
Job Details:
01/17/2020
REFRIGERATOR FRIGIDAIRE LFHB2751TF6
The customers water shut off valve is bad and has a small leak. Show the customer the problem spoke to the daughter over the phone about the problem and she is calling a plumber.For payment; replaced water valve unit now working.
Near Fresno, CA 93704
Irvin
Job Details:
01/17/2020
WASHER WHIRLPOOL MHW3100DW0
F0/E1 - clothes in washer during clean cycle. 7726729180- TECHLINE. Check pump and lock. Cleared the air dome cleared the pump cleared the pressure hose. Powered unit. Ran calibration passed. All ops. Normal.
Near Thousand Oaks, CA 91320
Aaron
Job Details:
01/17/2020
REFRIGERATOR MAYTAG MFI2570FEZ06
The correct address is 570 Camino Agua DulceNeeds a 4 call count Checked the unit compressor was cold checked the relay 120 volts to in replaced relay tested the compressor is bad shorted out bad needs new compressor and main board; ordrng 1 W11043763 (cntrl-elec) and 1 W11209866 (COMPRESSOR )
Near Shafter, CA 93263
Andrew
Job Details:
01/17/2020
DISHWASHER KITCHEN AID KUDS30IVWH4
Customer stated unit was not starting and light was blinking. Plug-in unit try to enter diagnostics and Unit would not enter into diagnostics. Heavy duty light would flash rapidly and when you touch keypad a second light would come on and blinking rapidly. Remove door panel and disconnected auxiliary fan plugging it back in to see if that would work. He was still having same issue most likely it is a stat key on the keypad or Shorty keypad order and keypad for customer; ordrng 1 WPW10250017 (panel-cntl)
Near Oxnard, CA 93036
Joe
Job Details:
01/17/2020
WASHER AMANA NTW4516FW2
"Units transmission is leaking oil bad causing oil to get inside of all the parts underneath. Ordering parts.; ordrng 1 285565 (agitator assy,comp) and 1 W10721967 (drive pulley) and 1 W10890624 (motor-drve) and 1 W10913953 (actuator) and 1 W11162561 (CAPACITOR ) and 1 W11255272 (gearcase) and 1 WPW10006384 (drive belt)"
Near Oxnard, CA 93035
Joe
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL WRF757SDHZ00
Units lights won’t shine due to control not powering them. Ordering parts.; ordrng 1 W11224256 (cntrl-elec)
Near Los Angeles, CA 91401
John
Job Details:
01/17/2020
OVEN KITCHENAID KEBU208SSS02
"The lower oven has no convection fan motors, the appliance manager is most likely the issue. The temperatures inside the upper oven possibly not recovering due to the main control or the thermistor or the bake element. Customer will look into buying a new oven"
Near Bakersfield, CA 93314
Andrew
Job Details:
01/17/2020
VENT HOOD WHIRLPOOL WVW75UC6DS2
Customer said that Unit was crooked and dripping oil down the back wall. Checked unit and installation of vent hood is incorrect. Unit is not level and slants to the left. It’s her vent hood will have to come down and be reinstalled and leveled properly informed customer that this is something that needs to be done by the insulation company in the manufacture of the home. This is a major installation issue not a minor one but unit is working properly
Near Lake Isabella, CA 93240
Jim
Job Details:
01/17/2020
WASHER GENERAL ELECTRIC HTWP1400F2WW
"Replaced tub, motor, trans tube and seal."
Near Bakersfield, CA 93301
Jim
Job Details:
01/17/2020
DRYER WHIRLPOOL NGD4655EW2
Installed drive assembly kit. Unit tested ok
Near Oxnard, CA 93030
Joe
Job Details:
01/17/2020
WASHER WHIRLPOOL WFW92HEFC0
Unit had a sock stuck in the drain pump which only took me a few seconds to lean machine back and pull out. Only charging service call.
Near Tracy, CA 95304
William
Job Details:
01/17/2020
WASHER WHIRLPOOL WET4027HW0
"F7E6, found run cap mounting broke off harness wire open, repaired wire harness, ordered cap for unit.; ordrng 1 W11158830 (capacitor)"
Near Los Angeles, CA 91342
Raymond
Job Details:
01/17/2020
DRYER WHIRLPOOL WGD5600XW1
"Upon arrival unit had intermittent operation. Unit also does not have a spinning drum. Found seized rollers. Gas coils short cycling, and console and control with burn marks on the control. Needs console control, repair kit and coils.; rqstng P&A on 1 4392067 (dryer repair kit) and 1 WPW10269610 (console) and 1 WPW10317636 (cntrl-elec) and 1 WPW10328463 (coil-valve)"
Near San Bernardino, CA 92407
Rod
Job Details:
01/17/2020
ICEMAKER WHIRLPOOL WRX988SIBM01
Intermittent ice production Confirmed Ice door seals not sealing at ffd icemaker fascia ; ordrng 1 WPW10549589 (door-ice)
Near San Bernardino, CA 92405
Rod
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW5800BW0
Won’t agitate.....makes a lot of noise.Confirmed Noises gearcase............tubvoid at centerpost and leaked into gearcase oil and water slung over and saturated motor actuator belt and splutch assemblies requiring complete overhaul of machine. Breakage of some components will occur during overhaul process.; 1 W10324648 (tub-outer) and 1 W10528947 (drive hub kit) and 1 W10721967 (drive pulley) and 1 W10772621 (screw) and 1 W10832724 (drive motor) and 1 W11035747 (gearcase) and 1 WPW10006355 (actuator) and 1 WPW10006384 (drive belt) and 1 WPW10215115 (washplate)
Near Delano, CA 93215
Chase
Job Details:
01/17/2020
WASHER MAYTAG MHW6630HC0
"Upon installing new valves, broke plastic part of dispenser to hose. Ordering part.; ordrng 1 W11316600 (DISPENSER)"
Near Santa Clarita, CA 91390
Michael
Job Details:
01/17/2020
RANGE KITCHENAID KEBS208DSS11
Removed lower oven door and replaced two hinges WP4455526 and lower oven light bulbs WP4452164Oven lights now work as designed and oven door closes as designed. Cx now wants upper oven lights ordered and replacedNeed to order two light bulbs ; ordrng 2 WP4452164 (LIGHT BULB)s
Near Santa Clarita, CA 91351
Michael
Job Details:
01/17/2020
REFRIGERATOR KITCHENAID KRSC503ESS01
Cx states unit makes ice but does not dispense the iceRemoved auger motor and found no power to motor. Removed lower cover found no damage to harness no voltage to 3 wire plug under door. Removed unit and checked P3 gray and blue wire when dispenser pad is pressed control board pulsates out various voltages. Faulty control board.Ordering main control board W11172798 and UI W11340158Return 1-24-20 12-3 requested; ordrng 1 W11172798 (CONTROL BOARD) and 1 W11340158 (USER INTERFACE)
Near Atwater, CA 95301
Kenneth
Job Details:
01/17/2020
WASHER MAYTAG MVWB835DW3
Found unit leaking water from tub seal. Ordering new gearcase. Rescheduled customer for 1-20-20; ordrng 1 W10811956 (Gearcase)
Near Stevinson, CA 95374
Kenneth
Job Details:
01/17/2020
OVEN WHIRLPOOL WEG750H0HV0
Found unit with F8E0 cooling fan error. Display is displaying like 2 displays. Ordering console. New control board to be ordered. Rescheduled customer for monday 1-20-20; ordrng 1 W11205353 (Control) and 1 W11339754 (Console)
Near Livingston, CA 95334
Kenneth
Job Details:
01/17/2020
DRYER MAYTAG MGDB765FW0
"Found unit not chiming. Tried to adjust audio level. Will not adjust. Speaker bad. Ordering fascia. Poor venting. Informed customer to shorten there venting and make sure theres no blockage going outside the house. Rescheduled customer for monday 1-20-20; ordrng 1 W11089306 (Fascia)"
Near Hughson, CA 95326
Cruz
Job Details:
01/17/2020
WASHER WHIRLPOOL NTW4516FW2
"Fixed for FTC- cx claims unit will not turn on, ck voltage at cntrl and found 120v, I then installed new part (cntrl elec) calibrated for wash performance and ran a diagnostic test mode it completed filled, wash, drain, spin, locked & unlocked, no codes, no leaks, cx ok repair."
Near Turlock, CA 95380
Cruz
Job Details:
01/17/2020
DRYER MAYTAG MEDC215EW0
"Fixed- installed new part (timer) tested unit in a high heat cycle it heated fine, runs quiet, timer is advancing through cycles, unit is working as designed."
Near Bakersfield, CA 93312
Jim
Job Details:
01/17/2020
DRYER WHIRLPOOL KEHS01PMT2
Open high limit thermostat.; ordrng 1 279973 (cutoff-tml)
Near Denair, CA 95316
Cruz
Job Details:
01/17/2020
DISHWASHER WHIRLPOOL WDT970SAHV0
"Fixed- installed new part (adjuster) top rack is adjusting as designed, ran diagnostic test mode it completed filled, wash, drain, heated, no codes, no leaks, unit is working as designed, cx ok repair."
Near Winton, CA 95388
Cruz
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL WRT518SZFW00
"File # 7726884638 from wp trade team- cx claims unit is not cooling in both compartments, temp in FC in @ 42° found meats defrosted, found infestation, cx will call RAC for an exchange."
Near Monterey Park, CA 91754
Andy
Job Details:
01/17/2020
WASHER MAYTAG MHW6630HW0
Need dispenser ; ordrng 1 W11316600 (drawer)
Near Waterford, CA 95386
Cruz
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL WRX735SDHZ00
"Fixed- installed all new parts (plastic sq, panel, cntrl elec) I then inspected the following doors, cooling, temps, leveling, ice & water dispenser, lights, fans, are working as designed, cx ok repair."
Near Waterford, CA 95386
Cruz
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW5000DW2
"Fixed- installed new part (latch) calibrated for wash performance, ran diagnostic test mode it completed filled, wash, drain, spin, no codes, no leaks, unit is working as designed, cx ok repair. "
Near San Bernardino, CA 92410
Rod
Job Details:
01/17/2020
DRYER AMANA NGD4655EW1
No heatConfirmed Found thermal fuse shorted due to inferior connection at ignitor..........was not clipped in place and made intermittent contact.Corrected and as designed op returned.
Near San Bernardino, CA 92410
Rod
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW7300DW0
Dead machine. Lid locked unable to openOpened lid manually to access contents and m/s#Confirmed no diag led in control lid was locked. Inferior electrical can cause electronic malfuntions or complete failure of components.Andrew sr#7726921450. For documentation.
Near Los Angeles, CA 91331
Randy
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW8500DC3
Found washer not filling. Replaced with water valve Sent for pre I’d. After install ran test. Unit started to sound like valve was activated but didn’t fill. Made weird noises. Found unit cancelled and drained. Unit barely filled but lid did lock. Unit needs new control. ; ordrng 1 W11095627 (cntrl-elec) and 1 W11193817 (harns-wire)
Near Highland, CA 92346
Rod
Job Details:
01/17/2020
REFRIGERATOR WHIRLPOOL GR2SHKXKB02
Icemaker leakingConfirmed Found ice mold flaking and peeling and fill tube had been installed too close to edge of fill cupAs designed op returned after replacing icemaker fro truck stock; used 1 4317943 (ICEMAKER) from stock
Near Redlands, CA 92374
Rod
Job Details:
01/17/2020
WASHER AMANA NTW4516FW3
Washer shuts down and drainsHot water not entering Confirmed Found water supply turned off and water temp setting on other than cold/tap selection.Instructed consumer of proper temp settings...........not addressed in operators guide as to what to expect.
Near Fontana, CA 92337
Kevin
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW4715EW0
"While breaking off agitator, the basket broke. Unit needs basket. I installed agitator so customer can attempt to use. Ordering basket. Allow 2 hours. ; rqstng P&A on 1 W10554251 (spin basket)"
Near Tulare, CA 93274
Chase
Job Details:
01/17/2020
WASHER WHIRLPOOL WTW7300DW0
"F5E2, f5e3, F0e5, F2e1, multiple kid lock error codes, replaced lid lock. Calibrated. Tested unit, all ops now testing normal. Job complete."
Near Pinon Hills, CA 92372
Cesar
Job Details:
01/17/2020
MICROWAVE KITCHEN AID KMHC319ESS2
Replaced interlock for intermittent door issues found monitor switch wash not always making contact
Near Victorville, CA 92394
Cesar
Job Details:
01/17/2020
WASHER MAYTAG MVWC565FW1
Found codes for failed lid switch tested unit lid fails to lock lid switch does have power from control and all connections are good replaced failed lid switch all tested good ; used 1 W11307244 (LATCH) from stock
Near Santa Clarita, CA 91354
Michael
Job Details:
01/17/2020
MICROWAVE KITCHENAID KMHC319ESS5
Removed microwave from over range. Removed and replaced blower motor W10830695 and main control board W11413135Tested unit and fan now ops as designed. Reinstalled all parts and hung over range. Unit ops are as designed and Cx is happy job complete
Near Santa Clarita, CA 91350
Michael
Job Details:
01/17/2020
OVEN WHIRLPOOL WEG750H0HZ0
Removed and replaced stainless console W11339755Rebooted unit set date and time all cooking cycles now op as designed Cx is happy job complete
Near Santa Clarita, CA 91355
Michael
Job Details:
01/17/2020
DRYER MAYTAG MGDB765FW0
Cx states long dry times. Unit gets humid and muggy insideStarted timed dry and lint screen light is on. Went outside and found 0 airflow. Went inside garage and removed foil tape where flex tubing meets hard piping and found large mass of lint. Cleared obstruction and unit now flows and heats properly as designed. Job complete