We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Victorville, CA 92395
Brian G
Job Details: 10/28/2024
Inspected unit as necessary. Diagnosed user interface failure. User interface ordered and main control.; ordrng 1 W11478526 (User interface) and 1 W11614514 (Control)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Los Angeles, CA 91356
Leon
Job Details: 10/28/2024
Unit 102Cx states that unit is not cooling After running diagnostic test find that compressor is not running Sealed system issue ; ordrng 1 W11484639 (Compressor) and 1 W11353156 (Drier)
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRFN2823AS3
Near Victorville, CA 92395
Brian G
Job Details: 10/28/2024
File# 87682232. Spoke with Techline. Technician removed rear fresh food air tower. Technician found gasket between fresh food damper and air tower. Stuck together with double sided tape. Technician removed sticky portion of gasket. Ran diagnostics. Damper is now opening and closing properly. All OK. Allow 24 hours to stabilize.; O-emld tckt
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ05
Near Colton, CA 92324
Francisco
Job Details: 10/28/2024
Please rs on Sunday am 8-00 8:30 am; ordrng 1 W11566475 (Harness)
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS02
Near Redlands, CA 92374
Francisco
Job Details: 10/28/2024
"He led unit found defrost issue in fc,/ after further testing found heater at 29-30 ohms and bi metal opened, providing estimate for repair. Cx approved RS Saturday ; ordrng 1 W11224591 (Fan with defrost thermostat)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFF507HBS
Near Victorville, CA 92395
Brian G
Job Details: 10/28/2024
FF Damper knocking. Ordering damper. Humming noise cant duplicate. Customer will record audio if returns.; ordrng 1 WPW10479155 (Damper)
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Yucaipa, CA 92399
Rod
Job Details: 10/28/2024
"*******ATTENTION ..Missing manufacture code when tech recvd job dispatch*********Control will not allow motor to operate no voltage to motor. Controls need replacing. Too many fault codes.; ordrng 1 W11414079 (Cotrol, ui) and 1 Control,machine"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Bakersfield, CA 93306
James
Job Details: 10/28/2024
Door dented. Ordering new. Door that was sent is dented. Pics in pvr; ordrng 1 W11681454 (Door dispenser side)
We serviced a
GENERAL ELECTRIC DRYER - ELECTRIC
Model GFD55GSSN3WW
Near Bakersfield, CA 93308
James
Job Details: 10/28/2024
Unit door not holding switch tight during operation causing unit to think door is open. Ordering new switch and door; ordrng 1 WE04X34281 (Door switch) and 1 WE10X29718 (Dryer door)
We serviced a
GENERAL ELECTRIC REFRGERATOR
Model CVE28DP2NBS1
Near Bakersfield, CA 93308
James
Job Details: 10/28/2024
Used Navybean to diagnose. Updated software to boards. FZ thermistor out of range. Ordering new. ; ordrng 1 WR55X29875 (Thermistor)
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Delano, CA 93215
James
Job Details: 10/28/2024
"Unit has motor overload error and acu error ordering new motor, slider, clutch and acu. ; ordrng 1 W11195971 (Stator/motor) and 1 W10754448 (Clutch)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF5355WHZ04
Near Santa Maria, CA 93455
George
Job Details: 10/28/2024
Found refrigerator ice maker not turning need ice maker.; ordrng 1 W10884390 (Icemaker)
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Bakersfield, CA 93309
Raymond
Job Details: 10/28/2024
No ice. E5 error. Fill tube frozen. Needs fill tube heater ice maker and permagum; ordrng 1 W11658802 (Ice maker) and 1 W11087201 (Fill tube heater) and 1 212643 (Permagum)
We serviced a
WHIRLPOOL WASHER
Model wtw5057lw0
Near Bakersfield, CA 93312
Raymond
Job Details: 10/28/2024
"Broken lower harness, also drain hose installed to a longer hose running outside with no air break. Cx will rectify drain hose. Needs harness.; ordrng 1 W11643701 (Harness)"
We serviced a
WHIRLPOOL REFRGERATOR
Model WRS325SDHW05
Near Bakersfield, CA 93312
Raymond
Job Details: 10/28/2024
Wrong ice maker sent. Unit has seized ice maker needs replaced. ; ordrng 1 W11284458 (Ice maker)
We serviced a
KITCHEN AID DOUBLE OVEN
Model KODE307ESS03
Near Bakersfield, CA 93308
Raymond
Job Details: 10/28/2024
"#4787 code $145.00 CK Auth# N999U3 unit not operating properly, takes too long to cool down and a weird noise. Found upper cooling fan only has high and is low rpm, lower inop. While testing fans u it popped f9e0. Circuit on board failed. Needs controls and cooling fans. Cx declined quote. Advised cx to contact manufacture for authorization. Collected 145 check. ; ordrng 2 W11245567 (Cooling fan)s and 1 W11179310 (Control) and 1 W10801665 (Control)"
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model GSE25GSHPCSS
Near Riverside, CA 92509
Robert U.
Job Details: 10/28/2024
Found the plastic auger in the ice container itself broke in various different places. Ordered new ice container. ; ordrng 1 WR29X43994 (ICE BUCKET & AUGER)
We serviced a
MAYTAG WASHER
Model MVWC565FW
Near San Bernardino, CA 92405
Francisco
Job Details: 10/28/2024
Cx rejected service today.; O-emld tckt
We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Santa Maria, CA 93454
George
Job Details: 10/28/2024
Found dryer not heating element and thermestat need this parts.; ordrng 1 WP3391914 (Thermestat) and 1 WP3387747 (Element)
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Santa Clarita, CA 91351
ERICK H
Job Details: 10/28/2024
F9e2 and f0e3 error codes present. Drain hose installed 7 into standpipe. Called techline to further diagnosis. Techline recommended installing drain hose 4 into standpipe. They also recommended separating basket from tub and check drain pump filter for obstructions. Found metal buckle in drain filter. Removed obstruction and retested. Unit draining better but still draining slow and not draining completely. Drain pump has failed. SR#7739824549; ordrng 1 W10876600 (Drain pump)
We serviced a
FRIGIDAIRE RANGE - ELECTRIC
Model GCFI3060BFA
Near Templeton, CA 93465
Jack
Job Details: 10/28/2024
Found that the one pointer tech line said part is discontinued 5304536905. No longer available. Part to help take off top. Craig with tech line. Pan assembly 5304528600. Interface board is 5304536436. Took unit completely apart to see board assembly pan is damaged and needs replacing. Plus need part 5304536905 reliable has part and Frigidaire has them in stock. 800-599-7569 can order that tool assembly kit. File for today 87680433. Customer is calling in to see were they are going on this repair. ; ordrng 1 5304536905 (Tool assembly) and 1 5304528600 (Pan assembly) and 1 5304536436 (Interface board)
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW1
Near Keyes, CA 95328
Timothy G
Job Details: 10/28/2024
Inspected unit and found harnes has shorted out at pump. Ordered another lower harness. Filling up Thursday 31st. Part may not be available. Please notify Cx if part is not. I can repair this call Saturday if part is available then.; ordrng 1 W11643701 (Wire harnes2)
We serviced a
KITCHENAID REFRIGERATOR
Model KBFN502ESS05
Near Simi Valley, CA 93065
Ian Y
Job Details: 10/28/2024
Customer advised that door wasnt fixed when last tech left. Customer attempted to take spring out of top right hinge and lost screw for it. Need new screw and bushing. Ordering new hinge assembly. ; ordrng 1 W10121046 (Hinge) and 1 2307857 (Hinge) and 2 W11370632 (Screw)s and 2 8281164 (Stainless screw)s and 1 W10752868 (Door stop) and 2 W10761279 (Screw)s
We serviced a
GENERAL ELECTRIC WASHER
Model GTW485ASW0WB
Near Ventura, CA 93003
Kenneth
Job Details: 10/28/2024
Customer indicating they are still having same issues. Plugged in GE device and found there is no faults. Or cycle history. Called techline who had me manually clear out of balance error that never showed up on GE device. And then informed me that the reason customer has fabric in the agitator at the end of the cycle. Is cause the unit isnt selected to fabric softener which only changes the rinse and not the actual spin so softener should still dispense out of the agitator during the spin. Confirmed I had programmed new board to the proper personality. Unit is working properly per techline. Techline informed me to have customer set the unit to rinse with softener and see if they are still experiencing issues at that time. File#14651395 - Charles; O-emld tckt
We serviced a
GENERAL ELECTRIC WASHER
Model PFQ97HSPV0DS
Near Ventura, CA 93003
Isidro
Job Details: 10/28/2024
"Torn fine filter and leaking cracked water drain pump, correcting issue by; ordrng 1 WH01X35685 (Lint filter assembly) and 1 WH11X29539 (Drain pump assembly)"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Simi Valley, CA 93063
Ian Y
Job Details: 10/28/2024
Ran machine in diagnostic and found that it was draining and wash motor was working properly. Control panel wasnt responding to touch until I put unit in diagnostic. Unit wasnt storing any error codes. Ordering new panel and control board. Most likely wont replace sump but bringing back just in case. ; ordrng 1 W11415066 (Control) and 1 W11340447 (UI)
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Simi Valley, CA 93063
Paul M
Job Details: 10/26/2024
Fixed broken bezel.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC302ESS00
Near Los Angeles, CA 90049
Tim B
Job Details: 10/26/2024
Replaced gasket and heat formed it to seal. Unit functions as normal.
We serviced a
GENERAL ELECTRIC WASH/DRY COMBO
Model PFQ97HSPV0DS
Near Oxnard, CA 93030
Kenneth
Job Details: 10/26/2024
Found unit not draining therefore not advancing through cycles or properly drying. Found lint built up in the drain lines. Informed customer to make sure they are constantly cleaning the lint screen to prevent lint build up and to constantly clean the drain filter out of any built up lint. Lint built up in both drain filter and hose from tub to drain pump. Customer approves functions. Ran a full test cycle and cleared drain failure error.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS04
Near Oakdale, CA 95361
Andrew H
Job Details: 10/26/2024
Cx complaint water switch not working properly. Upon arrival. Ran diagnostics. Tested components as faulty. Installed new switch. Tested new components out OKAY. Reset control panel. Operating as designed
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ0
Near Lancaster, CA 93536
Jonathan
Job Details: 10/26/2024
"Tested unit found unit missing mounting crew and found loose handle, tighten handle, installed new mounting screw tested unit and is working properly"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM08
Near Ventura, CA 93003
Kenneth
Job Details: 10/26/2024
No light in freezer. Found unit with a broken freezer door switch. Replaced and tested. Unit is working properly. Customer approves function at this time
We serviced a
WHIRLPOOL LAUNDRY
Model WFW75HEFW0
Near Waterford, CA 95386
Timothy G
Job Details: 10/26/2024
Replaced damaged leak8ng seal. Unit is now working per design. Job complete
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Manteca, CA 95337
William
Job Details: 10/26/2024
"F9E1, unit not draining, removed water & clothes stuck in unit, removed obstruction from outer tub drain port, ran self diagnostic cycle, unit operating as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Bakersfield, CA 93313
Raymond
Job Details: 10/26/2024
"Unit not locking, worn lock, replaced and tested, unit functions as designed."
We serviced a
KITCHEN AID MW OVEN COMBO
Model KOCE500ESS09
Near Modesto, CA 95355
Andrew H
Job Details: 10/26/2024
Cx complaint power surge. Display error codes 9-1. Upon arrival. Ran diagnostics. Found miss wire error code. Reset control panel. Checked components out okay. Operating as designed
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW0
Near Bakersfield, CA 93309
Raymond
Job Details: 10/26/2024
"Use and care, for billing, found locked rotor fault. Replaced slider and tested, unit functions as designed."
We serviced a
WHIRLPOOL M/W OTR
Model WML55011HS07
Near Hanford, CA 93230
Enrique
Job Details: 10/26/2024
"Customer concerns; microwave making noise, and not heating correctly. Found damper making noise (rubbing on sheet metal). I re-installed damper. Microwave passed heating test at time of service."
We serviced a
KITCHENAID DISHWASHER
Model KUDS30FXSS0
Near Modesto, CA 95355
Andrew H
Job Details: 10/26/2024
Cx does not like how the bush buttons press. Because touch sensitive. Says sometimes shes pushing buttons down. Cx complaint not turning on. Dishes not cleaning properly. Upon arrival. Ran diagnostics. Reset control panel. No error code. Checked out components okay. Operating as designed. Srs
We serviced a
WHIRLPOOL MICROWAVE
Model WOEC3030LS01
Near Bakersfield, CA 93312
Raymond
Job Details: 10/26/2024
"Cx states unit not operating, tested and found cx not pressing the center of the button properly. Trying to engage switches with her thumb and with arthritis its difficult for her to press the center of the button. Instructed on use and care. Unit functions as designed"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Lemoore, CA 93245
Enrique
Job Details: 10/26/2024
Dryer not heating. Installed new thermal fuse. Dryer operating as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ01
Near Simi Valley, CA 93065
Richard R
Job Details: 10/26/2024
"Upon arrival, inspected unit check temperatures temperatures were at 2° in the freezer compartment one product temperature ran a diagnostics on the icemaker icemaker did not complete cycle at one point during my inspection of the icemaker I found three cubes of ice stuck in bail arm removed ice from the bail arm tested the unit again. The unit ran through complete psycho, infield, mold with water. Also upon my arrival, I found that the switch for the icemaker on and off was set on the off position. Part of the reason why the unit was not making ice but But the ice cubes blocking the bell arm where the root cause of the problem unit is now working as intended job complete"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near West Hollywood, CA 90046
Tim B
Job Details: 10/26/2024
Found oven not heating at all. Igniter was out. Replaced igniter and tested. Unit functions as normal.
We serviced a
FRIGIDAIRE RANGE
Model GCRE3060AF
Near Modesto, CA 95358
Timothy G
Job Details: 10/26/2024
Inspected unit and found cooktop working. Oven door was locked. Tried to unlock with diagnostic test. Control is sending power but motor is not unlocking. Replaced failed motor and unit is now working perfectly design. Cx approved repairs. Job completed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Waterford, CA 95386
Timothy G
Job Details: 10/26/2024
Inspected unit and found bottom ice maker making a popping/clicking sound. Replaced Im and unit is now cycling per design. Job complete.
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Los Angeles, CA 91344
ERICK H
Job Details: 10/26/2024
Cx states washer noisy during spin cycle. Off balance. Suspension passed all tests. No damage to Gearcase. Unit was not leveled. Leveled unit. Tested and calibrated unit. Unit operating as designed. Job complete.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Oakdale, CA 95361
Andrew H
Job Details: 10/26/2024
Cx complaint. Not spinning. Upon arrival. Ran diagnostics. Found broken belt. Either pulley faulty. Motor drive assembly cracked. Installed new motor assembly. Belt and idler pulley. Tested new components out okay. Checked heat. Operating as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Ripon, CA 95366
Andrew H
Job Details: 10/26/2024
Cx complaint. Freezer over cooling. And frost from evaporation of ice. Refrigerator over cooling. Tech line. Suggests. Not enough products in the freezer. Upon arrival. Ran diagnostics. Found frozen food on the refrigerator area. Reset control panel. Checked components out.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ01
Near Burbank, CA 91505
Tim B
Job Details: 10/26/2024
"Replaced heater,thermistor,control,and wire harness. Tested each component through diagnostics and unit functions as normal."
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Thousand Oaks, CA 91320
Richard R
Job Details: 10/26/2024
"On arrival, inspected unit and found unit not wanting to start during my inspection unit gave an F 84 error code float switch found float switch harness not completely pushed him to float switch pushed it in until he clipped in and it clicked in perfectly retested unit unit passed all tests and is working as intended job completed"
We serviced a
MAYTAG WASHER
Model MHW6630HW0
Near Ventura, CA 93003
Isidro
Job Details: 10/26/2024
"I installed and secured new main ACU control board, ran diagnostics test and unit is now operating as designed at this time of service leak free."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323AS8
Near Atascadero, CA 93422
Jack
Job Details: 10/26/2024
Found fill tube was not also sealing properly. Removed and saw air leak. Put in new fill tube and also applied permagum sealer around tube also. New tube had a foam seal around it which the original one had foam rings. Saw Icemaker harvesting and then filled. Saw no leak coming from Icemaker with new tube. Job completed ; used 1 5305877995 (Permagum sealer) from stock
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Oxnard, CA 93035
Kenneth
Job Details: 10/26/2024
Installed all new LEDs. Tested. Unit is working properly. Three lights were foamed in and connectors were extremely hard to get released. Did manage to get them to release and replaced. Still documented on SD Quickpics. Unit is working properly. Customer approves function.
We serviced a
KITCHENAID STOVE
Model KEBC167MSS00
Near Thousand Oaks, CA 91362
Richard R
Job Details: 10/26/2024
Upon arrival inspected unit found inner glass completely shattered. Found a small crack on one of the other glasses on the inside of the panel replaced both pieces of glass tested unit unit is working as intended
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ05
Near Ceres, CA 95307
Timothy G
Job Details: 10/26/2024
Replaced evap motor and blade. Unit is now working per design. Job completed
We serviced a
WHIRLPOOL LAUNDRY
Model WTW5010LW0
Near Santa Clarita, CA 91351
Richard R
Job Details: 10/26/2024
"Upon arrival, inspected unit put unit in diagnostics unit would not shift from agitate to spin that easily during my inspection of actuator found a ground up cam. Also when it went into spin, it did not have a lot of power. Replaced actuator cam and capacitor re-tested unit unit passed all testing is working as intended. Advise customer always evenly load the unit and never overload the unit job complete"
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Parlier, CA 93648
Timothy
Job Details: 10/26/2024
Installed UI and harness. Tested unit and found it operating as designed.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near San Fernando, CA 91340
ERICK H
Job Details: 10/26/2024
Bezel and bleach dispenser broken. ; ordrng 1 W11662175 (Bleach dispenser) and 1 W11559688 (Bezel)
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GZS22IYNYHFS
Near Bakersfield, CA 93306
James
Job Details: 10/26/2024
Spoke to Cx via 3x. Ok to reschedule to have time for techline call. Office to reschedule. ; O-emld tckt
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Manteca, CA 95337
William
Job Details: 10/26/2024
"Replaced back panel, blower wheel; ordrng 1 W11641158 (Lent screen shute) and 1 WP8577230 (Blower housing)"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Modesto, CA 95357
Timothy G
Job Details: 10/26/2024
F6E3 f7e7 F1e2. Unit needs to have ui and control changed together. Also motor fault codes reappear while testing. Follow up scheduled for Tuesday anytime. Notify Cx with time as soon as possible.; ordrng 1 W11478525 (Ui) and 1 W11621180 (Corlm) and 1 W10754448 (Clutch) and 1 W10734521 (Slider) and 1 W11195971 (Mor)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ13
Near Lemoore, CA 93245
Enrique
Job Details: 10/26/2024
Ice maker not producing ice. Incoming voltage 120 vac. Faulty on/off switch.; ordrng 1 W11700250 (Ice maker)
We serviced a
GENERAL ELECTRIC DRYER - ELECTRIC
Model GTX22EASK0WW
Near Modesto, CA 95350
Timothy G
Job Details: 10/26/2024
Inspected unit and found wire burnt off element. Element needs to be replaced and need to return to repair. Schedule when available ; ordrng 1 WE11X21156 (Element andhoisi g) and 1 WE08X37097 (Wire harness)
We serviced a
MAYTAG M/W OTR
Model MMV6190FW
Near Los Angeles, CA 91311
Paul M
Job Details: 10/26/2024
Unit is not heating when on convention mode. Will need to replaced air guide magnetron and boards. ; ordrng 1 W11031990 (Ui board) and 1 W11381424 (Main board) and 1 W10536989 (Thermistor) and 1 W10533104 (Air guide) and 1 W10533104 (Air guide magnetron) and 1 W10458325 (Axtuator) and 1 W10568805 (Resistor)
We serviced a
GENERAL ELECTRIC WASHER
Model HTW265ASW0WW
Near Bakersfield, CA 93304
James
Job Details: 10/26/2024
"Rattling noise continues and does not reach speed correctly. after replacing gearcase, shifter, clutch and trans pulley. Agitator tight. Ordering new motor and trans pulley; ordrng 1 Wh03x32097 (Trans pulley) and 1 WH03X29559 (Motor) and 1 WH03X32218 (Motor pulley)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Riverbank, CA 95367
Andrew H
Job Details: 10/26/2024
Black fasteners missing. Cx complaint. Condensation is from air vents.; ordrng 1 W10503548 (Black fasteners)
We serviced a
HOTPOINT REFRIGERATOR
Model HPS18BTNFRWW
Near Santa Maria, CA 93458
Jack
Job Details: 10/26/2024
Found freezer freeing and refrigerator was at 40 degrees. Found the condenser fan not running and compressor not running. Found roaches behind the hole area by compressor. Starter was not looking good. Calling tech line on this unit. ; schdld next appmnt for 10/28 MON !
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Palmdale, CA 93552
Jonathan
Job Details: 10/26/2024
Tested unit found broken harness to drain pump; ordrng 1 W11643701 (Harness)
We serviced a
GENERAL ELECTRIC WASHER
Model GTW325ASW0WW
Near Quartz Hill, CA 93536
Jonathan
Job Details: 10/26/2024
Tested unit and found defective belt. Belt pic on order; ordrng 1 WH01X27538 (Belt)
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW3
Near Lancaster, CA 93534
Jonathan
Job Details: 10/26/2024
"Tested unit found effective roller pulley, and belt. Will need unit accessible for repair.; ordrng 1 4392067 (Dryer kit)"
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ1
Near Riverside, CA 92507
Robert U.
Job Details: 10/26/2024
Found the front right igniter cracked and sending the spark sideways instead of up to the burner cap. Ordering holder and burner head. ; ordrng 1 W11557816 (Orifice holder fr) and 1 W11435660 (Burner head)
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Pasadena, CA 91103
Stephen
Job Details: 10/26/2024
"Pump runs constantly. Ran diagnostics. Has f1e1, f8e1, f3e1 error codes. Found pump relay stuck. Needs control. Out of stock at vendor. ; ordrng 1 W11607637 (Control) and 1 W11038689 (Water inlet valve) and 1 WPW10006384 (Belt)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Riverside, CA 92503
Robert U.
Job Details: 10/26/2024
Found the unit has two error code stored at this time. One is a f4e3. Wash motor not running and indeed it is now but it is receiving power. Second the unit has a f7e1 error code. I ran diagnostic cycle and the heater is operating. Ordering a control for that. ; ordrng 1 W11613479 (Pump and motor) and 1 W11683652 (Control electric)
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Simi Valley, CA 93065
Paul M
Job Details: 10/26/2024
Will need to reschedule for Saturday. ; schdld next appmnt for 11/2 SAT !
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Manteca, CA 95337
Andrew H
Job Details: 10/26/2024
Cx complaint. Not heating. Upon arrival. Ran diagnostics. Power surge error code. Found wire harness damaged. Acu damaged. Acu. W11577490W11556656 wire harness.; ordrng 1 W11577490 (Acu) and 1 W11556656 (Wire harness)
We serviced a
MAYTAG WASHER
Model MVWC565FW
Near Oxnard, CA 93033
Kenneth
Job Details: 10/26/2024
Unit not agitating or spinning. Found suspension rods super bouncy causing off balance loads. Drive hub stripped. Not allowing basket to turn. Cam is worn out not allowing actuator to shift it to spin or agitate properly. Belt slipping on cam. ; ordrng 1 W10528947 (Hub) and 1 W11130362 (Suspension) and 1 W10721967 (Cam) and 1 W10913953 (Actuator) and 1 W11239857 (Belt)
We serviced a
SPEED QUEEN WASHER
Model AWN632SP116TW02
Near Oxnard, CA 93033
Kenneth
Job Details: 10/26/2024
Unit is spinning. But when cycle is done the tub is leaving over to the right. If I recenter tub and push it all the way back or forward. The tub will spring back centered. But does not spring back centered if pushed to the right. It will just stay there. Push to the left and basket springs back center. Ordering all 6 leveling springs. ; ordrng 6 37575 (Spring)s
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Palmdale, CA 93552
Jonathan
Job Details: 10/26/2024
Tested unit found effective slider and clutch also found error code F7E4; ordrng 1 W10734521 (Slider) and 1 W10754448 (Cluch)
We serviced a
MAYTAG DRYER
Model MGD7230HW3
Near Modesto, CA 95358
Timothy G
Job Details: 10/26/2024
No parts in bin for this job. Called Cx to notify that not parts were received. Need to get parts and return. Schedule as soon possible with extra time; O-emld tckt
We serviced a
KITCHEN AID RANGE
Model KSEG700ESS
Near Fresno, CA 93710
Timothy
Job Details: 10/26/2024
Customer states they used the oven once and it was so hot on the sides she was worried about the cabinets. Ran unit at 400f and checked with a thermal couple. Per W11544031 REV A the unit has to be running for an hour at this temp before measurements are to be taken. I will need to speak with tech support to go further with this call. ; schdld next appmnt for 10/29 TUE AM
We serviced a
MAYTAG WASHER
Model MVW6500MW0
Near Bakersfield, CA 93308
James
Job Details: 10/26/2024
F7e3 f7e4 unit not shifting to spin or agitate. Also not shutting of when power is pressed. Ordering new shifter and will install with acu on return visit. ; ordrng 1 W11481722 (Shifter)
We serviced a
GENERAL ELECTRIC WASHER
Model GTW335ASN2WW
Near Somis, CA 93066
Isidro
Job Details: 10/26/2024
"Broken belt, correcting issue by; ordrng 1 WH01X27538 (Belt)"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Bakersfield, CA 93308
Raymond
Job Details: 10/26/2024
"Unit being used at a multi living facility, per exclusions this is not covered need to document with manufacture ; schdld next appmnt for 10/26 SAT !"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS02
Near Bakersfield, CA 93307
Raymond
Job Details: 10/26/2024
Picked up data loggers; O-emld tckt
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Bakersfield, CA 93304
Raymond
Job Details: 10/26/2024
"Installed shifter, no agitation, wires have continuity but will not shift. Ordering harness, control and splutch; ordrng 1 W11643701 (Lower harness) and 1 W11626074 (Control) and 1 W10721967 (Splutch)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ17
Near Bakersfield, CA 93304
Raymond
Job Details: 10/26/2024
"Unit not dispensing ice, stripper impeller. Needs divider motor impeller and washer. ; ordrng 1 WPW10309864 (Divider) and 1 W11671282 (Motor) and 1 W11378860 (Spacer) and 1 WP63052-2 (Impeller)"
We serviced a
MAYTAG WASHER
Model MVW7232HC2
Near Delano, CA 93215
James
Job Details: 10/26/2024
"F0e7, clothes detected during clean washer cycle. Cx showed video of unit in high speed spin with clothes. During high speed spin basket wobbles. Ordering stator, rotor clutch and slider; ordrng 1 W10754448 (Clutch) and 1 W10734521 (Slider) and 1 W10915700 (Stator)"
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Bakersfield, CA 93305
James
Job Details: 10/26/2024
No error codes when arrived. Ran automatic test cycle. Unit off balance during spin. Loose suspension and noise from trans pulley. Ordering suspension and will install belt and pulley on return visit. ; ordrng 1 W11396716 (Suspension)
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Bakersfield, CA 93312
Raymond
Job Details: 10/26/2024
"Cx states clothes are not washing and will just stay wet. Aborting cycle. Found long fill, drain hose laying down on back side of unit draining outside. This is also leaking, flood hazard present. Advised cx to rectify drain hose, cx signed waiver. Unit will operate as designed when installed correctly. Need to document with manufacture. Scheduling for Tuesday. ; schdld next appmnt for 10/29 TUE !"
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD702MPS00
Near Bakersfield, CA 93308
Raymond
Job Details: 10/26/2024
"Ice maker has slow production. Ice maker is making ice. Pressure is in range. Replaced ice maker, locking tab broke during replacement. Needs bracket.; ordrng 1 W10749631 (Bracket)"
We serviced a
WHIRLPOOL REFRGERATOR
Model WRS315SDHZ18
Near Tracy, CA 95304
William
Job Details: 10/26/2024
"Found water over flowing at fill tub, ordered fill tub extension kit for unit. As per Technical Service Pointer #: W11750800 Rev A; ordrng 1 W11750811 (Fill tub extension kit)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ0
Near Tracy, CA 95304
William
Job Details: 10/26/2024
"F8E4, F9E2, Ran self diagnostic cycle, found no water leaks, advised cx to run 2 full cycles, returning today for reinspection. Unit may tub leak.cx ran 4 full cycle, found float area with water in it, ordered tub assy for unit.; ordrng 1 W11409866 (Tub assy) and 1 W11412291 (Drain pump)"
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model CWE23SP2MJS1
Near Pismo Beach, CA 93449
Jack
Job Details: 10/26/2024
Found drain pan full of water. Over flow. Even in drain tube. Don with tech line. Insurance number 888-456-7445. Striker and mullion on door. File number 14635981. Mullion striker WR01X31733. Mullion WR17X13240. ; ordrng 1 WR17X13240 (Mullion) and 1 WR01X31733 (Mullion striker)
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Riverside, CA 92508
Robert U.
Job Details: 10/26/2024
Found the unit has two issues. First the unit has a f9e1 but no water left in the unit. The pressure sensor on the control is bad and not recognizing the water has left the machine. Second the unit has a f1e2 drive motor over voltage. The motor is supposed to be steady at 8-10 ohms but it jumps all over the place as high as 11 and as low as 7. Ordering motor for that. ; ordrng 1 W11621180 (Control electric) and 1 W11700916 (Latch) and 1 W11457841 (Strike) and 1 W11195971 (Stator)
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Lancaster, CA 93535
Jonathan B.
Job Details: 10/25/2024
JB out 10/25/24.Customer states the washer shakes during spin cycle.Tested washer spin cycle verified cabinet shakes. Adjusted front left leveling leg to firmly sit against the flooring. Unit shaking is almost 0 now. Advise customer washing machine is sitting on a hollow floor and wheel. Recommend installing washer on a concrete floor surface to alleviate shaking. no use or needed. No charge to customer.JOB COMPLETE
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Ripon, CA 95366
Martin R
Job Details: 10/25/2024
Replaced compressor and condenser pulled vacuum it held recharged and ran unit there is good heat exchange all functions working per design Job complete
We serviced a
KITCHEN AID DISHWASHER
Model KDTE104ESS1
Near Bakersfield, CA 93311
Esteban S
Job Details: 10/25/2024
Quoted for motor sump assembly.
We serviced a
WHIRLPOOL WASHER
Model WTW5005KW0
Near Tulare, CA 93274
J.E.
Job Details: 10/25/2024
"Cycled unit and found bad shifter causing off balance and damaged to cam and latch. Ins new shifter new cam and new latch. Unit now working as designed job completed ; used 1 W11307244 (Latch), and 1 W10913953 (Actuator) from stock"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2623AB8
Near Porterville, CA 93257
J.E.
Job Details: 10/25/2024
Cycled unit and found fill tube out off position causing small amount of water to slide down wall of freezer eventually causing ice build up on evaporator fan cage. Repositioned and secured fill tube cleared ice buildup and retested icemaker no longer leaking. Job completed
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Santa Paula, CA 93060
Isidro
Job Details: 10/25/2024
"F0e2 oversuds also noisy cam pulley stripped, loose nut on the floor. I installed and secured a new drive pulley kit,I calibrated the machine and unit is now operating as designed , cx approved repair"