Replaced U.I board tested unit and also calibrated unit rant component test unit passed all test went over with customer unit is now working as designed job complete

Only replaced ice maker assembly tested ice maker unit is now working as designed went over with customer job complete

Alex components and tested. Unit now heating as intended.

JB out 6/2/23. Upon arriving customer states the ice production is now operating properly but the water dispenser produces a loud deep humming noise when dispensing water.Removed toe panel grille and inspected water inlet valve solenoid l tightened valve mounting bracket. Tested again. No more loud noise. Reins toe panel grill. Tested operation again. Dispenser operation is now working as designed. No more loud noise. No charge to customer. JOB COMPLETE

Installed new water valve retested unit now working as designed at time of service job completed

Rplaced broken door strike. Tested after repair all ok.

Unit making loud noise during spin cycle. I found cam not engaging all the way. Removed and replaced cam assy All tests good ; used 1 W10721967 (DRIVE PULLEY) from stock

Cx states that unit is making loud noise during spinning Replaced repair kit Tested unit working properly as required

Upon arrival tested unit got the unit to 425 with no smells the burner cover was not in correctly I put it in the way it was supposed to be installed unit is working as intended advised customer that cuz its new that they might have some wired smells the first few uses of the unit burning off stuff from the factory but I did not detect any smells job complete

"Installed compressor, recharged wi5 60 grams of r600. Tested, unit functions as designed. Allow unit to regulate to temps."

Led new components and unit is working as intended.

Cx states unit will not agitate. Unit is outside and not connected. Cx said I could take it in and hook it up. Told her that I wouldnt be the one to take unit back in if further diagnose is needed. Unit will need to be hooked up and accessible if needed to return. Water valves were clearly clogged. Also remove a handful of change inside washplate. Those were the issues I could find without full access to machine. Machine will need to be fully hooked up if we are called back.

Performed inspection. Found dent at freezer door gasket location both right and left side cabinetry. Provided pictures to tech line. Deemed unit unrepairable. SR#7736546178. Transferring to Trade partners spoke w/customer service ref#7736530504 started process to replace unit

Unit had a burnt wire at heat element. Spliced a new wire and unit heats per design. Job complete.

Inspected unit as necessary. Spoke with Techline. Diagnosed DSI board failure. Removed and replaced. DSI board. Tested operation. All OK.

Upon arrival replaced UI and ACU ran unit through multiple diagnostic modes. No more fault codes unit is working as intended.

Customer stated that the unit makes noises between cycle. Checked unit for error codes no codes. Ran u it through diagnostics and found noise is spray arm spraying door. May be caused by calcium buildup. Customer to clean with vinegar. Tested all works good at this time.

Found unbalance detection lever rattling against the bin making noise re secured the lever to the lid and ran cycle. Unit passed all tests and noise is no longer present.

Cycled unit and found leaking gear case causing damage to other components. Unit will need new gear case slider and clutch assembly.

Customer stated that the dryer keeps pausing the cycle mid cycle. Removed and replaced console and door switch tested all works good at this time.

Replaced evaporator assembly fan is working correctly now and refrigerator is getting good air flow also heating element is working properly went over with customer customer is now satisfied job complete

"On arrival unit not draining, loose connection at drain pump. Secured and tested, unit functions as designed."

Replaced defective control board. Tested unit and is working properly.

Upon arrival replaced all LEDs in unit they are covered under #: S84638 all unit lights are working as intended

Installed new infinite switch and UI retested unit passed all tests at time of service job completed

"Installed and secured parts listed, unit should now operate properly as designed, I advised the customer to let the unit regulate itself overnight for proper temperature, customer approved repairs"

Replaced the ui control. The unit is now cooling per design. Job complete.

Installed part tested checking out ok paid thrue I wallet no dents or dings cause by tech.

Installed up board unit tested ok complete

Found no error codes stored. I removed and replaced all parts ordered and both pulleys are nice and tight and the agitator is as well. All tested ok in diagnostic and job completed.

Called Tech line 7736474397 test ran system. No error codes. check for leaks. Customer issue frost buildup on suction line. Visual check found food storage compartment food Blockage at cooling air vent openings. removed items. No frost buildup at this time or noise at this time. Customer will attempt to document pic/audio future issues Unit operating correctly.

"New construction not occupied yet. Maintenance stated that the unit was not cooling. I tested unit, all temps are normal. I secured all heater connections. All tests good."

"Different issue. Tested unit, unit is heating. And all ops are working properly. Informed client to clean vent for better efficiency. Customer education on use and care"

Replaced part, job good to go

Top ring loose suspension worn. Reset top ring and replaced the suspension

Found valve not opening replaced tested working properly

Installed parts tested check out ok complete no dents or dings cause by tech.

Installers didnt properly balance fridge. Balanced fridge. Fridge working properly.

"JB out 5/23/23. Customer states Dishwasher Wash is but does not dry dishes. Verified dishwasher tank/tub was replaced recently by ARS. Note model serial tag is not available as tub was just recently replaced. Recommend customer contact KitchenAid factory service and request a replacement. Model serial tag to be shipped to them to be affixed to the dishwasher. Ran dishwasher verified incoming supply water temperature at 78°F. Instruct customer installation instructions provided with dishwasher From KitchenAid require a minimum of 120°F. Hot water supply to the dishwasher by the house. Hot water supply heater. If water is not hot enough, it will not evaporate and therefore will not promote drying. Tested dishwasher verified water is not hot enough. Recommend customer purchase and install a point of use hot water heater located under the kitchen sink adjacent to the dishwasher set for 125°F so that when the dishwasher is used it will receive no less than Required 120° minimum the moment the start button is pressed. Also recommend use of liquid rinse aid in Dispenser. Unable to verify any mechanical issue. No charge to customer. Job complete."

New pump and drain pump. Unit now washing and draining per design. Job complete

"Replaced defective igniter, tested unit and is working properly"

Removed and replaced timer and knob. Tested unit. All tests good.

"Found a worn clutch assembly (CAM). Had it replaced washer okNOTE: washer is being over used, and very time its something different ; used 1 W10721967 (Cam) from stock"

Installed new ui and retested unit passed all tests at time of service job completed

Replaced parts needed. Found bent bracket and it was coming from door. Replaced and tested. Checked out. Customer is happy. No more horrible sound. Job completed.

Fill tube is way to far in to the unit. F8e1 f5e2 f0e1. Running a full diagnostics test and seeing what unit does. Unit fills washes spins and drains as designed now. John with tech line. Definitely fixed the issue with the drain tube so far in. Sr number 7736476643. Job completed.

New switch and element installed. Unit now working as intended. Cx to purchase new drip pans for unit.

Installed new actuator motor capacitor product tested OK complete

Replaced all parts. Tested unit and is working properly

"As per pre id, a new Jazz board has been replaced and programmed as per design."

"Upon arrival, replaced complete wire harness with thermistor and replaced dampener. Advise tenant to give 24 hours for the unit to regulate itself. Unit is turned on and blowing as intended cooling as intended as well. Job complete."

Found evaporator fan not running. Found 120v at the connector. Replaced the fan and ran cycle. Unit passed all tests and is operating as designed.; used 1 WP2315539 (Evap fan) from stock

Ran dishwasher for about 20 minutes without any leaks. No fault codes stored.

Found the original diffuser not clipped in all the way and the thermistor was in the wrong location. I removed all the ice and replaced all parts listed. The unit is now circulating air the way it should be. It will take 24 hours to get back to normal temps. Ice maker and chute is no longer leaking after replacing the valve and chute. Job completed.

"JB out 5/23/23. Customer states during spin cycle,unit is very loud and shakes/dances away from wall. Tested drain and spin (no clothes) upon arrival to demonstrate washer will spin smoothly. Asked customer to load a regular wash load. Verified correct fill, wash (agitation) drain and spin functions.Redistributed wash load off balance (on purpose) to demonstrate an off balance load. Customer agreed this is what has been the experience.Properly redistributed load an spin again. To verify in customers presence the wash is operating correctly. And sometimes even the most evenly balanced wash loads may migrate out of balance.No parts needed. Adjusted front right leveling leg.No charge to customer.JOB COMPLETE"

"Removed the to the freezer found the black wire backed out, pin on the heater assembly replace the heater assembly and evaporator thermistor. Tested operation. Unit is working as designed at this time."

Tested found valve making noise because the road construction

Replaced defective heater and fill valve. Cycled ice maker.Tested ok

Found complaint wont spin. Cx had a cycle cancel full of water w clothes. Tested unit working as designed. Checked outlet. Cx has electrical issues. Referred to electrician. Unit working as designed cx instruct on load and care

Found the cap tube restriction at the cap to three way valve for the fresh food evaporator. After cutting affected area out and soldering the new connection there is now a full frost pattern on the fresh food evap. All tested ok after repair. Job completed.

Found a dead washing machine replace control board washer OK

"Found water line kinked at top of door, replaced water line and tested unit working as designed"

Install the new detergent assembly

Unit completely dead. Cx does not want to go through with repair. Did not perform any work. Will give us a call if they want us to come back out to assess.

Cx explained unit had a small water leak. Filled with water and drained and found the internal drain hose was loose and slowly leaking. Reconnected and verified issue is fixed.

Replaced harness tested unit dryer is heating and tumbling job complete

Replaced IM Unit working properly as needed

Customer stated that unit is not draining. Found failed pump. Removed and replaced pump tested all works good at this time. Not a recall different issue.

Silicone both freezer and refrigerator door gaskets open. Replace the refrigerator light switch tested operations unit is working as designed now.

F0E9 off balance pause. Cx was washing a blanket. Advised Cx to use deep fill when washing bulky things. Unit passed all tests and is working per design. Job complete.

Unit would not stop spinning the had to turn it off Manually removed old unit installed new unit operating as designed job complete

Improper drain hose installation. Unit is suffering from lack of water. Advised to have correct drain pipe installed. Job complete. Not a recall. This is a different issue. Job complete

"Install the new part on the unit. Retest the unit and now unit is working properly, no leaks at this time. Job complete"

Replaced lid and ran cycle. Unit passed all tests and is operating as designed.

Tested icemaker normal tested compressor normal tested damper normal tested all components customer has recorded noise about half way up on right side of cabinet un able to reproduce noise called tech

Upon arrival replaced timer assembly start switch and door latch. Switch unit turned on as it as it was intended unit heat it up as it was intended as well during my tests unit is not working as intended job complete

"Found two issues, control was locked, educated cx on feature and also start button works intermittently. Cx chose not to repair start button at this time."

Inverter change out. Removed existing inverter. Installed new inverter. Test ran unit. Unit operating correctly.

Confirmed loose connection to hi limit thermostat. Re connected and tested. All functions now heating and working as Designed.

Cx concerned about detergent not being dispensed. Flushed out detergent dispenser re programmed control. All functions now working as designed. Instructed cx n certain cycles and to be running clean wash cycle.

Replaced ice maker tested good

Replaced suspension Tub no longer has sag and all functions are working per design job complete

Perform diagnostic check. Test ran unit. Found no error codes. Checked calibrations. Informed customer on loading unit. Unit operating correctly.

"Lights working as intended in microwave. Opened and closed door and found no irregularities in function, signs of failure or error codes in diagnosis. Shared findings with trade partner and noted that microwave is functioning properly.Sr # 7734017860"

Replaced main board Unit working properly as required

"Upon arrival replaced soap dispenser. Enter door vent motor vent main control board ran unit multiple times, so no leaking whatsoever job complete"

Replaced defective valve. Tested unit and is working properly no leaks at this time.

The claimed noise was coming this time from compressors compartment and I had to pull unit out and found a pigtail vibrating against the compressors compartment service panel. I have made proper adjustments to such and noise issue was solved.

Replaced suspension tested good

"Ran diagnostics. Not draining. Found drain pump jammed. Unjammed drain pump. Locks/ unlocks, fills,washes, drains, rinses,dispenses, and spins properly at this time. Instructed customer on unbalanced loads. Complete."

Replaced all selected parts Unit working properly as required

Fixed- error code f2e1 stuck key- cleared code- ran calibration and auto test they pass- no leaks- all buttons are working as designed- cx ok repair

"Fixed- installed new parts (clutch, slider, rotor, latch, agitator, gear case) calibration test pass- auto test pass- no leaks- no errors- cx ok repair-"

Replaced all selected parts Unit working properly as required

Installed inverter and compressor. Recharged system with 4.50 oZ of R134A and tested. Unit is working properly. Customer approves function. Compressor kicked on and starting runnning. Tested and found freezer getting to 40 degrees. Informed customer to let unit run till tomorrow to see if its cooled. If water placed in freezer is frozen. Ok to load with food.

Installed burner heads and caps. Tested unit. Unit is working properly. Customer informed me her grates were cracked. Instructed customer to call her warranty. They could possible send directly. If not. Please order grates before return out to call

"Installed defrost heater, harness, thermistor and co tell box. tested, unit functions as designed"

Dishwasher was installed with a one way water supply line and it was put on backwards keeping water from flowing into dishwasher. Flipped water line into correct direction. Dishwasher now filling and successfully completing all cycles. Dishwasher now working properly.

"Cycled unit and found door. Heart is not connected. Connecting door harness, and retested door Unit now working as designed. Job completed."

Adjusted water regulator. Water no longer dripping and fridge no longer making irregular sounds.fridge working properly.