Service History 118 - Appliance Repair Specialists

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Riverdale, CA 93656

Enrique

Job Details: 02/20/2025

Broken lid. Installed 2 hinges and lid. Washer operating as designed. No leaks.

We serviced a

WHIRLPOOL DRYER

Model WGD5300SQ0

Near Los Angeles, CA 91401

Tim B

Job Details: 02/20/2025

Found after market attachment n vent. pictures in SDMobile unit on repairable due to the extensive damage caused by customer.

We serviced a

MAYTAG WASHER

Model MVW6230HW3

Near Delano, CA 93215

Esteban S

Job Details: 02/20/2025

Valve and control. Board were removed and replaced. Unit passed all test. Unit is working as intended.

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Los Angeles, CA 91326

Paul M

Job Details: 02/20/2025

"Unit was not spinning properly, found unit to have a bad slider. After replacing slider unit still had issues and water was present in between Gearcase and tub. The harness looked compromised which is why I replaced it. The connection was wet and I thought it caused a short. Replaced harness and main board unit was still not spinning. Replaced clutch and stator. After replacing unit was still making a loud noise when spinning. Replaced gear case and tested unit out. It is now working properly. Leak looks to be. Owing from gear case area. Replaced gear case and did not see any damage to the tub. Unit was calibrated and ran diagnostics. Working properly."

We serviced a

WHIRLPOOL WASHER

Model WFW4720RW0

Near Barstow, CA 92311

Jonathan B.

Job Details: 02/20/2025

JB OUT 2/20/25Customer states that in Spin cycle the washing machine shakes and vibrates.Upon arrival tested unit in spin cycle. Verified unit drains and spins. Adjusted front Left leveling leg to prevent shaking.Tested again. Verified unit is operating as designed. No charge to customer.JOB COMPLETE

We serviced a

KITCHENAID COMPACTOR

Model KTTS505ESS2

Near Atascadero, CA 93422

Jack

Job Details: 02/20/2025

Replaced switch and unit is now working as designed. Tested again after pulling bin out and put back. Still working as designed. Job completed.

We serviced a

GENERAL ELECTRIC WASHER

Model GFW850SPN2RS

Near Oxnard, CA 93033

Ian Y

Job Details: 02/19/2025

Found lead to drain pump slightly backed out. Secured connection. Ran diagnostics with Smart HQ tool. Unit now draining properly.

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Santa Clarita, CA 91390

Felipe S

Job Details: 02/19/2025

"Upon arrival found unit with error code F2E1 and F3E1, this about stuck key and pressure system failure. Check the unit and found pressure system is no working properly, run a test cycle 51, and into the test step 5 dont pass, according with tech sheet needs new control board. Blow some air through the hose and no blockage or pinch. Replace the control board. Retest the unit and now is working properly. Job complete"

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW0

Near Los Banos, CA 93635

David C

Job Details: 02/19/2025

Found drain pump unplugged reconnected also found f0e2 error code informed CX on how much soap to use

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS05

Near Los Angeles, CA 91306

Sean W

Job Details: 02/19/2025

"Ui displaying E5 Icemaker error code and Icemaker doesnt fill when testing with Icemaker fill test,replaced Icemaker and dual water valve,Icemaker now harvesting and filling with water."

We serviced a

KITCHENAID REFRIGERATOR

Model KSSO36FTX04

Near Oak Park, CA 91377

Richard R

Job Details: 02/19/2025

"Upon arrival, inspected unit found water leaking into icemaker mold constantly inspected valve found bad solenoid on valve replaced valve unit is no longer dripping water unit was turned off and not to temperature. Advise customer to give unit at least 24 hours for it to make its first batch of ice due to the unit, not being cold enough for the units icemaker to go into harvest mode. I did advise the consumer that if after 24 hours the unit does not make any ice that is possible for an icemaker to go bad that we would send one out I would not charge for the labor to replace the icemaker. complete."

We serviced a

MAYTAG DRYER

Model MGD5640TQ0

Near Riverside, CA 92505

Robert U.

Job Details: 02/19/2025

Found the thermal fuse open and reason for not heating.Customer okayed the repair. I replaced the thermal fuse and heat is restored.

We serviced a

AMANA REFRIGERATOR

Model ARB9059CS

Near Los Angeles, CA 91316

Ron H

Job Details: 02/19/2025

Replaced ice maker tested ice maker ice maker worcking properly

We serviced a

MAYTAG WASHER

Model MVW6230HW2

Near Corcoran, CA 93212

Enrique

Job Details: 02/19/2025

"Washer was making grinding noise. Found: weak suspension, shifter fault and broken drive pulley assembly. Installed 3 parts, performed calibration. Washer operating as designed. No leaks.; used 1 W11396716 ( Suspension), and 1 W10913953 ( Actuator) from stock"

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS06

Near Bakersfield, CA 93308

Chase

Job Details: 02/19/2025

There is no abnormal frosting in FC. There is some frost from the cold temperature but this is normal. All operations are testing out normal. Adjusted temp up one degree. There is nothing wrong with this unit at all. All functions are working as designed.

We serviced a

FRIGIDAIRE DISHWASHER

Model FDPC4221AS

Near Bakersfield, CA 93307

Chase

Job Details: 02/19/2025

"Old spray arm tag broke and melted. Installed new spray arm, tested unit. All ops now working as designed."

We serviced a

GENERAL ELECTRIC DRYER - ELECTRIC

Model GTD48GASWWB

Near Palmdale, CA 93550

Jonathan B.

Job Details: 02/19/2025

"JB OUT 2/19/25DISPATCHED MODEL/SERIAL. GTD48GASWWB, AA518853CACTUAL MODEL/SERIAL. GTD4BGASW0WB, AA518853CCustomer states dryer does not shut off when any sensor cycle is in use. Dryer will only shut off when timed dry cycle is used. Tested dryer in time dry cycle verified timer did advance to off and unit did shut off. Tested dryer again in normal, sensor cycle with no clothing in the dryer verify timer or dial did advance towards off an eventually shut off. Unit is operating correctly. Instruct customer exhaust vent hood is partially restricted and will cause the dryer to take more time to dry. Recommend the customer remove the exhaust vent hood and replaced with a louvered style exhaust vent hood to remove the restriction. Also recommend customer use less clothing in the washing machine and dryer.Corrected loose wire connection to thermostat.OK, no parts used or needed. Unit is operating as designed. No charge to customer. Job complete."

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Castaic, CA 91384

Felipe S

Job Details: 02/19/2025

"Upon arrival found unit with error message about the door needs to be closed, and the door is closed, check the unit door and found the strike is broken causing the failure. Replace the strike on the door, retest the unit and now is working properly. Job complete"

We serviced a

MAYTAG REFRIGERATOR

Model MSS25C4MGZ06

Near Bakersfield, CA 93309

Jim

Job Details: 02/19/2025

Ice maker casing was tearing apart. Replaced ice maker.

We serviced a

MAYTAG WASHER

Model MVWP575GW1

Near Riverside, CA 92501

Robert U.

Job Details: 02/19/2025

Found the agitator warped and loose to the transmission. I replaced the agitator and replaced it and made sure the bot that holds it into place was tight because it did loosen up before I got here. After replacing both parts of the agitator I ran a diagnostic cycle and the unit is not agitating. The arm on the actuator is broken and reason for failure. I replaced the actuator and ran a recalibration cycle and all functions are now working properly. No error codes stored. Job completed.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW585BSV3WS

Near Santa Clarita, CA 91390

Felipe S

Job Details: 02/19/2025

"Upon arrival found unit with noise when is on agitation. Check the unit and found loose connector on the mode shifter causing the pulley dont go all the way up. Readjust the connector and retest the unit, now is working properly, unit as well is properly level. Job complete"

We serviced a

AMANA DRYER

Model NED4655EW1

Near Bakersfield, CA 93307

Chase

Job Details: 02/19/2025

"Vent is completely restricted. Showed cx the air return and here is barely any air at all coming out. Cx will get this issue taken care of for, vent cleaning service. All ops with machine are working as designed."

We serviced a

GENERAL ELECTRIC WASHER-DRYER COM

Model GUD24GSSM1WW

Near Castaic, CA 91384

Felipe S

Job Details: 02/19/2025

"Upon arrival found unit no heating up at all, check the unit and igniter get hot, but no flame. Check the unit and found the primary connector for the gas coils was loose causing no gas to the burner. Readjust this connector and retest, now unit is working properly. Job complete"

We serviced a

MAYTAG WASHER

Model MVW7230HC1

Near Ridgecrest, CA 93555

Brandon

Job Details: 02/19/2025

Units hot valve was not working upon arrival. Popped the console up and found a poorly connected wire harness at that valve. Retested after correcting issue. All valves working as designed.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FPFU19F8WF3

Near Bakersfield, CA 93313

Chase

Job Details: 02/19/2025

"Defrosted evap, cleared drain. Installed new components. All functions now working as designed"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ07

Near Los Angeles, CA 91326

ERICK H

Job Details: 02/19/2025

Replaced drier and compressor. Pressurized with 250psi of nitrogen. Unit held pressure. Vacuumed system for 20 minutes. Unit held vacuum. Charged with 54g of r600a. There is proper heat exchange. Advised Cx to give unit 24 hours to get unit down to operating temps. Job complete.

We serviced a

WHIRLPOOL DRYER

Model WGD5100HW1

Near Paso Robles, CA 93446

Jack

Job Details: 02/19/2025

Replacing part list. Motor. Replaced motor and put all back together. Unit is now getting hot and motor is spinning drum correctly. Made sure no more codes. Job completed

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Riverside, CA 92503

Robert U.

Job Details: 02/19/2025

Found the unit has a f7e9 error code and a f5e2. I ran diagnostic and the slider is scraping against the clutch so its causing a locked rotor error and the latch is not unlatching. I replaced the slider rotor and latch and ran a diagnostic test. All functions restored and working properly so the unit removed the error codes for me. All functions are working properly and job completed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Atwater, CA 95301

Manuel B

Job Details: 02/19/2025

Ice maker works innermidient. I still knew ice maker.run harvest and fill test cycle ok.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN3WW

Near McFarland, CA 93250

Esteban S

Job Details: 02/19/2025

Drain pump and mode shifter were removed and replaced. Unit passed all test. Unit is working as intended.

We serviced a

WHIRLPOOL WASHER

Model WTW6157PB0

Near Riverside, CA 92508

Robert U.

Job Details: 02/19/2025

Found the agitator barrel broke first. So the customer removed it and just used the wash plate. After some time the wash plate cracked in half. I replaced the wash plate and agitator. After that I ran a diagnostic cycle to check all other functions and all functions are working properly. Job completed and sending parts back.

We serviced a

MAYTAG DISHWASHER

Model MDB8959SKB3

Near Los Angeles, CA 91352

Oscar L

Job Details: 02/19/2025

"Because of unprecedented F1 E1 error code splashing on the screen, a new main controller was replaced.A quisk diagnostic and testing were conducted and all worked as designed. I need your signature."

We serviced a

MAYTAG WASHER

Model MVWB765FC3

Near Los Angeles, CA 91352

Oscar L

Job Details: 02/19/2025

"Because of a heavy shaking during spin cycle, a new suspension set plus a new rotor have been replaced. Factory calibration and all basic operation were successfully tested."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ03

Near Fillmore, CA 93015

Felipe S

Job Details: 02/19/2025

"Upon arrival found unit with no lights on the top section of the fresh food compartment and freezer. Check the unit and found a bad led on the freezer causing the failure. Replace the led on the freezer, retest now unit is working properly. Job complete"

We serviced a

MAYTAG DRYER

Model MGDC215EW2

Near Highland, CA 92346

Jonathan

Job Details: 02/19/2025

Tested found wire disconnect on thermostat reinstalled tested working properly

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Bakersfield, CA 93313

Chase

Job Details: 02/19/2025

Installed new dispenser. All ops now working as designed.

We serviced a

WHIRLPOOL WASHER

Model WFW5620HW0

Near Port Hueneme, CA 93041

Ian Y

Job Details: 02/19/2025

Removed and replaced units water valves. Tested in diagnostic automatic test mode. Unit passed no error codes. Job complete.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAKZ2

Near Tehachapi, CA 93561

Samson O

Job Details: 02/19/2025

"Replaced bad control board, unit test ok. Saw a black spot on the case of the ACU. Complete"

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN3WW

Near Perris, CA 92571

Kevin

Job Details: 02/19/2025

Customer had video of product making noise during agitation. It sounded like the belt was slipping. Removed and replaced belt and tested with load. All tests and sounds normal.

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Lemoore, CA 93245

Enrique

Job Details: 02/19/2025

"Installed wire harness, performed calibration. Washer operating as designed. No leaks."

We serviced a

GENERAL ELECTRIC WASHER

Model GTW485ASW0WB

Near Adelanto, CA 92301

Cesar

Job Details: 02/19/2025

Replaced belt

We serviced a

JENN-AIR MICROWAVE

Model JMW2430IL02

Near Lathrop, CA 95330

William

Job Details: 02/19/2025

"Replaced ui panel, cleared code, set up model #, ran micro wave water heating test, test, unit operating as designed"

We serviced a

WHIRLPOOL DRYER

Model WGD5050LW3

Near Highland, CA 92346

Jonathan

Job Details: 02/19/2025

Tested unit noise not present at time of service found Found loose wire to main board also has vent restriction

We serviced a

WHIRLPOOL WASHER

Model WTW7120HW0

Near Manteca, CA 95337

William

Job Details: 02/19/2025

"Replaced soap container draw, tested in diagnostic, ran self diagnostic cycle, unit operating as designed."

We serviced a

WHIRLPOOL WASHER

Model WTW5100HC3

Near Riverside, CA 92503

Robert U.

Job Details: 02/19/2025

Found after replacing both hoses the unit is no longer leaking. It is now holding water and able to continue with the cycle without leaks. All functions restored and working. Job completed.

We serviced a

WHIRLPOOL DRYER

Model WED7500GC0

Near Turlock, CA 95382

Cruz

Job Details: 02/19/2025

"Fixed- found error code f4e4 - found thermal to be open causing unit not to start- removed and replaced with new one (thermal fuse) tested, unit is now working as designed- good air flow- cx ok repair"

We serviced a

KITCHEN AID REFRIGERATOR

Model KRMF706ESS01

Near Adelanto, CA 92301

Cesar

Job Details: 02/19/2025

Replaced fan tested good

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Santa Maria, CA 93454

George

Job Details: 02/19/2025

Installed part tested check out ok complete.

We serviced a

WHIRLPOOL WASHER

Model MVWC465HW3

Near Bakersfield, CA 93306

James

Job Details: 02/19/2025

Noise from drive pulley and belt. Replaced with new belt and drive pulley. Tested and unit is now working as intended.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ03

Near Sanger, CA 93657

Timothy

Job Details: 02/19/2025

Installed switch and LED. Tested unit and found it operating as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ15

Near Oxnard, CA 93036

Isidro

Job Details: 02/19/2025

"Installed new compressor and service valve, pulled vacuum unit held, charged with 54 grams of R600, unit started pulling heat and should operate as designed with in 24 hours"

We serviced a

AMANA REFRIGERATOR

Model ASI2575GRS08

Near Fresno, CA 93727

Timothy

Job Details: 02/19/2025

Installed control. Element harness and defrost thermistor . Secured thermistor with a zip tie. Tested element to make sure it was connected correctly. Unit checks ok.

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Redlands, CA 92374

Jonathan

Job Details: 02/19/2025

Installed slider tested working properly

We serviced a

FRIGIDAIRE DISHWASHER

Model FDPH4316AS0A

Near Ridgecrest, CA 93555

Brandon

Job Details: 02/19/2025

Replaced cables. Door is now opening and closing normally.

We serviced a

WHIRLPOOL WASHER

Model MVWC565FW

Near Muscoy, CA 92407

Francisco

Job Details: 02/19/2025

"Checked unit found cam was stuck and broken actuator. Removed and replaced both parts, calibrated and tested ops unit now working properly.; used 1 W10721967 (Cam) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHB04

Near Clovis, CA 93612

Timothy

Job Details: 02/19/2025

"Installed chute, IM and ice door. Tested unit and it checks ok."

We serviced a

MAYTAG DISHWASHER

Model MDB9959SKZ1

Near Santa Clarita, CA 91350

Ian Y

Job Details: 02/19/2025

"Removed and replaced Ui board. Tested, unit going into cycles no longer displaying F6 E1 error."

We serviced a

WHIRLPOOL REFRGERATOR

Model KRFC704FPS06

Near Los Angeles, CA 91607

Ron H

Job Details: 02/19/2025

Replaced inverter board tested unit unit worcking properly

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ07

Near Wasco, CA 93280

Esteban S

Job Details: 02/19/2025

Compressor and tubbing were removed and replaced. Unit started to cool. Unit is working as intended.

We serviced a

GENERAL ELECTRIC RANGE - ELECTRIC

Model JBS360RT3SS

Near Bakersfield, CA 93311

Jim

Job Details: 02/19/2025

Replaced control board and other parts. Properly wired the oven at the board.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW585BSV2WS

Near Perris, CA 92571

Kevin

Job Details: 02/19/2025

Customer concerned with blankets going off balance. I tested unit with load of towels. All tests good. Instruct customer on off balance loads.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Los Angeles, CA 91344

Felipe S

Job Details: 02/19/2025

"Install dispenser assembly, solenoid and holders. Retest the unit and now is working properly. Job complete"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ3

Near Manteca, CA 95337

William

Job Details: 02/19/2025

"Replaced scratched outer SS door panel, tested ui panel functions, unit operating as designed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ16

Near Los Angeles, CA 91406

Oscar L

Job Details: 02/19/2025

"Because of cooling issues due to a locked compressor, an SSR was performed and the following parts and components were replaced, compressor, drier , service port. Customer was asked to allow at least 48 hours before packaging up groceries."

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Pomona, CA 91767

Jaime

Job Details: 02/19/2025

Installed new control board as well as the heater element

We serviced a

MAYTAG WASHER

Model MVW4505MW2

Near McFarland, CA 93250

Esteban S

Job Details: 02/19/2025

Valve was removed and Replaced. Unit passed all test. Unit is working as intended.

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ0

Near Lancaster, CA 93535

Samson O

Job Details: 02/19/2025

"Replaced bad sump, unit tested ok. Complete"

We serviced a

KITCHENAID DISHWASHER

Model KDPM604KPS1

Near Lancaster, CA 93536

Samson O

Job Details: 02/19/2025

"Found unit misalignment from the floor around the feet. Installed again and unit installed very well now, unit test ok. Complete"

We serviced a

MAYTAG DRYER

Model MED6630MBK0

Near Atwater, CA 95301

Cruz

Job Details: 02/19/2025

"Fixed- installed new parts (wheel, motor) tested unit, its heating, no errors- found cx household venting to be restricted, found wet lint, look at picture- cx will need to call a professional to clean out venting- ducting from dryer is clear from debris. Cx ok repair"

We serviced a

WHIRLPOOL WASHER

Model WTW6120HW0

Near Wasco, CA 93280

Esteban S

Job Details: 02/19/2025

"Suspension and cam were removed and replaced. Belt ,a king loud noise. Belt was removed and replaced. Unit passed all test unit is working as intended."

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Turlock, CA 95380

Cruz

Job Details: 02/19/2025

Fixed- installed new part (cntrl elec) calibration test pass- auto test pass- no leaks- no errors- unit now working as designed- cx ok repair

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDHV02

Near Bakersfield, CA 93308

Aaron

Job Details: 02/19/2025

"Replaced the ice maker unit cycled and filled ok , and replaced light module , ops ok now at this time"

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Fresno, CA 93727

Joe P

Job Details: 02/19/2025

Installed main board tested unit working to manufacture specifications everything past test. Job complete.

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Atascadero, CA 93422

Leo R

Job Details: 02/19/2025

"Replaced ACU and recalibrated and tested all components manually. Unit runs as designed, Job complete."

We serviced a

WHIRLPOOL M/W OTR

Model WMH31017HS06

Near Los Banos, CA 93635

David C

Job Details: 02/19/2025

Replaced transformer and cap as well as diode from to stick tested unit unit working as designed; used 1 W11222648 (Diode) from stock

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Apple Valley, CA 92307

Cesar

Job Details: 02/19/2025

Replaced control calibrated and tested all checked good

We serviced a

GENERAL ELECTRIC WASHER

Model GFW850SPN5RS

Near Bakersfield, CA 93312

Aaron

Job Details: 02/19/2025

Replaced the main board and motor tested operations ok now at this time

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model GSS25GYPJCFS

Near La Crescenta-Montrose, CA 91214

Oscar L

Job Details: 02/19/2025

"A new cover was installed and consumer will be the maximum testers, will reach out if needed."

We serviced a

GENERAL ELECTRIC REFRGERATOR

Model PVD28BYNBFS

Near Bakersfield, CA 93311

Randy

Job Details: 02/19/2025

Unit is now outside. No water connected. Removed and replaced valve. Found iced up on Evap on fresh food section. Defrosted. Tested. Cooling now working cx to wait 24 to 48 hours for ice and proper temps.

We serviced a

JENN-AIR MICROWAVE

Model JMW3430DS02

Near Moreno Valley, CA 92557

Kevin

Job Details: 02/19/2025

Removed and replaced console that whirlpool sent out to customer. Tested unit. All tests good.

We serviced a

GENERAL ELECTRIC FREEZER

Model FUF21QRRBWW

Near Phelan, CA 92371

Cesar

Job Details: 02/19/2025

Replaced compressor recharged unit all tested good

We serviced a

WHIRLPOOL OVEN

Model WOD51EC0HS20

Near Highland, CA 92346

Jonathan

Job Details: 02/19/2025

Found display not responding replaced tested working properly

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT1835VW6

Near Alhambra, CA 91803

Stephen

Job Details: 02/19/2025

"Returning defective main board. Light not working. Replaced main control board. Light is working properly, unit is cooling properly at this time. Complete."

We serviced a

WHIRLPOOL COMPACTOR

Model GC900QPPB7

Near Nipomo, CA 93444

George

Job Details: 02/19/2025

Installed part tested check out ok complete

We serviced a

GENERAL ELECTRIC RANGE - GAS

Model CGS750P4M5W2

Near Lancaster, CA 93536

Jonathan B.

Job Details: 02/19/2025

"JB OUT 2/19/25Replaced both hinge receivers, Liner (inner) door ASM, screws, fastener bracketsResReassembled door and reinstalled onto range.No Charge to customer JOB COMPLETE"

We serviced a

MAYTAG REFRIGERATOR

Model MSC21C6MFZ05

Near San Bernardino, CA 92407

Francisco

Job Details: 02/19/2025

Removed and replaced door. Unit now working properly.

We serviced a

MAYTAG DISHWASHER

Model MDB4949SDZ0

Near Los Angeles, CA 91324

Sean W

Job Details: 02/19/2025

"Cx concerned with edges of dishwasher door and feels that they are too sharp,calling techlin.; schdld next appmnt for 2/20 THU !"

We serviced a

WHIRLPOOL REFRGERATOR

Model wrx735sdbm02

Near Los Angeles, CA 91306

Sean W

Job Details: 02/19/2025

"Cx unavailable,took picture and notified office.; saved tckt"

We serviced a

MAYTAG WASHER

Model MVW7232HC

Near Visalia, CA 93277

J.E.

Job Details: 02/19/2025

Cycled unit and found leaking Gearcase causing damage to drive components. Ordering parts ; ordrng 1 W11449841 (Gearcase) and 1 W10915700 (Stator) and 1 W10915701 (Rotor)

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT1835VW

Near Visalia, CA 93291

J.E.

Job Details: 02/19/2025

Cycled unit and found faulty control board. Need new control boards ; ordrng 1 5304528823 (Control board)

We serviced a

JENN-AIR MICROWAVE

Model JMW2430DS01

Near Exeter, CA 93221

J.E.

Job Details: 02/19/2025

Cycled unit and found faulty microwave control board. Quoted customer 713 for full repair. Customer agreed. Ordering part. Collected service fee; ordrng 1 W10815465 (Microwave control board)

We serviced a

MAYTAG DRYER

Model MEDB835DW4

Near Springville, CA 93265

J.E.

Job Details: 02/19/2025

Cycled unit and found found broken blower wheel and stripped motor. Ordering parts for repair. ; ordrng 1 W11126010 (Motor) and 1 WP697772 (Blower wheel)

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW2

Near Visalia, CA 93291

Enrique

Job Details: 02/19/2025

Washer is not agitating due to stripped Gearcase and agitator. shifter fault. Need all parts to refurbish the washer. 2 JOOOB COUNT. Square trade will ship parts to customer.; ordrng 1 W11454741 (Gearcase) and 1 W10721967 (CAM) and 1 W10913953 (Actuator) and 1 WPW10006384 (Belt) and 1 WP389140 (Block) and 1 285565 (AGITATOR)

We serviced a

GE WASHER

Model GFW850SPN0RS

Near Madera, CA 93636

Joe P

Job Details: 02/19/2025

"Motor is internally shorted, inverter is also not working shorted. During inspection found rear counter balance, broken in pieces, struts are bad, causing unit not to balance gave customer estimate. Customer paid the 145 collected. $145.00 CC Auth# K99LY3. Informed customer they have 30 days to decide if they want to repair the unit or not. Job complete.; ordrng 4 WH03X29516 (Suspension)s and 1 WH03X29524 (Motor) and 1 WH03X29522 (Belt) and 1 WH02X29660 (Rear counter weight) and 1 WH22X35837 (Inverter)"

We serviced a

KITCHEN AID RANGE

Model KCGS956ESS05

Near Bakersfield, CA 93314

Jim

Job Details: 02/19/2025

Replaced harness and the continuous sparking stopped. Now the right from burner will not light; ordrng 1 W11690598 (Choke) and 1 W11173537 (Holder) and 1 W11678108 (Flame spreader) and 1 W10836474 (Burner)

We serviced a

KITCHENAID REFRIGERATOR

Model KRSC703HPS05

Near Lathrop, CA 95330

William

Job Details: 02/19/2025

"Found evap fan foam cracked,not fitting properly , ordered evap fan/foam assy & missing middle crisper shelf assy.; ordrng 1 WPW10440266 (Middle crisper bin shelf) and 1 W11608966 (Fan /styrofoam assy)"

We serviced a

MAYTAG WASHER

Model MVW7232HW2

Near Bakersfield, CA 93314

Jim

Job Details: 02/19/2025

F7E4 fault code. The motor and stator have been rubbing together and shaving; ordrng 1 W11449841 (Transmission) and 1 W10915701 (Rotor) and 1 W10915700 (Stator) and 1 W10754448 (Clutch) and 1 W10734521 (Slider) and 1 W10902814 (Agitator)

We serviced a

KITCHEN AID REFRIGERATOR

Model KRMF706ESS04

Near Bakersfield, CA 93311

Jim

Job Details: 02/19/2025

Freezer evaporator is not defrosting. All thermistors checks passed. The defrost heater will work when in diagnostic testing. There is a DC issue with the system because the 3 way valve keeps energizing. ; ordrng 1 WPW10675033 (Board) and 1 W11249952 (Fan motor) and 1 W11330971 (User interface)

We serviced a

MAYTAG DRYER

Model MGD7230HC1

Near Bakersfield, CA 93314

Chase

Job Details: 02/19/2025

"After installing new parts. There is still a tapping noise present. Coming from rear bulk head, deformation in bulk head. Will replace rear bulk; ordrng 1 W11162465 (Bulkhead)"

We serviced a

MAYTAG WASHERHER

Model MVW4505MW1

Near Bakersfield, CA 93313

Chase

Job Details: 02/19/2025

Broken drain pump wire. To short to repair. Will replace wiring harness. ; ordrng 1 W11643701 (Harness lower)