Service History 103 - Appliance Repair Specialists

We serviced a

WHIRLPOOL FREEZER

Model WRS325SDHZ00

Near Camarillo, CA 93010

Ian Y

Job Details: 10/29/2024

"Found unit in a no cooling situation. No frost pattern on evap. All fans running properly. Checked high and low side lines and both werent even slightly hot. Quoted customer between 800$-1000$ for compressor, Evap, labor and service fee. Customer said he would consider repair but would talk to fiancé and they were leaning more towards getting a new refrigerator."

We serviced a

WHIRLPOOL WASHER

Model WTW5105HW1

Near Bakersfield, CA 93312

Joe P

Job Details: 10/29/2024

"Code F1E1 drain pump. Checked drain pump, has 120v and good neutral. Pump has no resistance open. customer declined at this time."

We serviced a

MAYTAG WASHER

Model MVW6500MBK0

Near Bakersfield, CA 93308

Joe P

Job Details: 10/29/2024

"Installed new ACU board,ran diagnostic cycle test passed all test. Job complete."

We serviced a

MAYTAG LAUNDRY

Model MVWB765FW0

Near Port Hueneme, CA 93041

Ian Y

Job Details: 10/29/2024

"Found units clip holding pump to drain hose slipped halfway off allowing water to come out of bottom of hose. Had new clip in car. Secured hose and clipped it properly. Pulled on hose to make sure there wouldnt be repeat problem. Hose was secure. Tested, unit no longer leaking."

We serviced a

AMANA WASHER

Model NTW4516FW

Near Port Hueneme, CA 93041

Ian Y

Job Details: 10/29/2024

"Found that units valve connection to cold water solenoid had backed out. Reconnected solenoid. Tested, unit now filling. Customer also complaining about water level. Explained to customer that this washer was high-efficiency and only gave out a specific amount of water."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT910SSYM1

Near Thousand Oaks, CA 91362

Richard R

Job Details: 10/29/2024

On arrival inspected unit. Customer stated that unit will not drain. Put unit into diagnostics only error code that the unit gave me was an F6 East six which was water temperature water to cold advise customer to make sure he runs the hot water in his Fossett before starting a cycle to ensure hot water going to the unit inspected drain line there was a possible obstruction in the drain line. I retested unit and diagnostics unit passed all tests and diagnostics and its draining as intended. Ran diagnostic three times unit drained perfectly. It is possible that the garbage disposal was full of food at the time of At the time of the cycle and did not allow unit to drain advise customer for smell to buy a fresh pods and run a cleaning cycle on the unit and do this at least once a month at the moment all ups are normal advising customers they have any more issues to please call us back job complete

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Santa Paula, CA 93060

Isidro

Job Details: 10/29/2024

"Unresponsive UI control panel. Installed new UI panel, unit is now coming on and operating as designed at this time of service also"

We serviced a

JENN-AIR DISHWASHER

Model JDB8700AWS3

Near Nipomo, CA 93444

Jack

Job Details: 10/29/2024

Found the outlet seems to be ok but the garbage disposal wont work either. Outlet really lose inside. Tested with another outlet and popped it. Had to reset it. Found main board has a short in it. Giving customer a quote for repair. Main board W10866118. Customer is going to purchase a new dishwasher after quote. Job completed

We serviced a

GE OVEN

Model PKD7000SN5SS

Near Bakersfield, CA 93313

Raymond

Job Details: 10/29/2024

On arrival screen is stuck at setup. Power cycled unit and pulled error codes. None found. Went through setup again and unit completed setup. Tested unit and unit is operating as designed. Cx should follow up with manufacture or vendor for manuals or use and care guides.

We serviced a

MAYTAG DRYER

Model MED7230HW3

Near Lathrop, CA 95330

William

Job Details: 10/29/2024

"F2E1, Checked power to unit, checked air flow, reseated all connections to ui panel, checked HMI functions, unit operating as designed."

We serviced a

WHIRLPOOL WASHER

Model WTW5005KW0

Near Tulare, CA 93274

J.E.

Job Details: 10/29/2024

Cycled unit and found unit off balance. Installed new suspension and new hub retested unit now working as designed job completed

We serviced a

WHIRLPOOL LAUNDRY

Model WTW500CMW0

Near Bakersfield, CA 93313

Raymond

Job Details: 10/29/2024

"Unit off balance, found loose strut, secured and tested, unit functioning as designed. Also explained proper loading and cycle selections."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Oak Park, CA 91377

Richard R

Job Details: 10/29/2024

"Upon arrival inspected unit Well, running water from the dispenser I found the Filter housing Leaking a lot found bad O-ring on quick fitting in housing. Replaced housing re-tested unit unit is no longer leaking. I ran about a gallon and a half of water and found no leaks. All ups are normal now. Job complete."

We serviced a

FRIGIDAIRE OVEN

Model GCWM3067AFA

Near Perris, CA 92571

Kevin

Job Details: 10/29/2024

Unit giving error code F50 again and also gave F105 one time. I called tech line again ( file 87674184 ). They recommend replacing oven relay board. Customer declined at this time.

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW0

Near Lompoc, CA 93436

Kash S

Job Details: 10/29/2024

"Found unit sharing during spin, found dampers failing, replaced dampers, verified with cx unit is spinning without excessive shaking or vibration, advised cx on load size and types for optimal operation, cx has no further questions/concerns, unit is fully operational at this time"

We serviced a

MAYTAG DRYER - ELECTRIC

Model MGD4500MW1

Near Wasco, CA 93280

Esteban S

Job Details: 10/29/2024

Timer and knob were removed and replaced. Unit passed all test. Unit is working as intended.

We serviced a

JENN-AIR OVEN

Model JJW2427DS03

Near Los Angeles, CA 90077

Leon

Job Details: 10/29/2024

W11232102Total $1446.34Collected full amount Replaced console Unit working properly as needed

We serviced a

KITCHENAID OVEN

Model KOSE500EWH20

Near Bakersfield, CA 93312

Brandon

Job Details: 10/29/2024

Ventilation piece under the door fell apart. I was able to put it back together and reinstall it. Unit is now directing airflow as designed.

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KPS1

Near Simi Valley, CA 93065

Richard R

Job Details: 10/29/2024

"Upon arrival, inspected unit and found unit not getting any water at all but union diagnostics unit gave me an F8E2 error code, which was a inlet water valve electrical problem replacing the water valve re-tested unit unit passed all the test and is working as intended job complete"

We serviced a

KITCHEN AID RANGE

Model KSEG700ESS7

Near Fresno, CA 93710

Timothy

Job Details: 10/29/2024

Had the customer run the unit at 400f for 1 hour. Took a temperature with thermocouples taped to the side of the unit until the temperature stabilized. The highest reading was 124f the limit is 152f. The gaskets look good the flew is installed correctly and the heat blanket is installed correctly. Unit is operating within expected parameters per WPTS 7740213824

We serviced a

WHIRLPOOL REFRIGERATOR

Model WZF34X16DW08

Near Victorville, CA 92395

Cesar

Job Details: 10/29/2024

Found loose ground wire connection at cabinet from power cord. This caused GFI to trip cutting off power to unit. Secured ground wires making sure cabinet is properly grounded all tested good. Customer had food loss do to no cool

We serviced a

MAYTAG DRYER

Model MGD6200KW4

Near Los Angeles, CA 91326

Sean W

Job Details: 10/29/2024

"Broken tab on door handle caused it to fall off of door.replaced broken handle with new one,door can now be opened and dryer is working properly."

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC0

Near Ceres, CA 95307

Timothy G

Job Details: 10/29/2024

Inspected unit and found softener tray over flowing. Checked for clog. No clog. Valve is spraying hard causing water to run out of softener tray. Replaced valves and unit is now working perfectly per design. Recalibrated load size and job completed

We serviced a

JENN-AIR MICROWAVE

Model JMW3430DS02

Near Los Angeles, CA 91403

Leon

Job Details: 10/29/2024

W11236885Total s.c and labor $362.92Replaced console. Unit Working properly as required

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ08

Near Orcutt, CA 93455

George

Job Details: 10/29/2024

Found refrigerator not dispensing ice found rod for ice container off position reinsert unit functions tested 3 times complete return parts.

We serviced a

WHIRLPOOL OVEN

Model WFG525S0HZ

Near Los Angeles, CA 91040

Samson O

Job Details: 10/29/2024

Replaced bad hinges. Complete

We serviced a

MAYTAG DISHWASHER

Model MDB8959SKZ0

Near Tehachapi, CA 93561

Randy

Job Details: 10/29/2024

Unit would keep running f9e1. Would not fill. No water in float switch. Removed and replaced pump n motor. Tested. Now fills and washing. Now working as designed.

We serviced a

MAYTAG WASHER

Model MVWC565FW2

Near Moreno Valley, CA 92557

Kevin

Job Details: 10/29/2024

Unit not starting cycle. I found that the motor was just humming. I found leaking capacitor causing issue. Removed and replaced capacitor. Tested unit. All tests good.

We serviced a

KITCHENAID COMPACTOR

Model KTTS505ESS2

Near Bakersfield, CA 93311

Randy

Job Details: 10/29/2024

New install. Latch loose. Door not closing all the way. Removed and installed properly. Unit now working as designed

We serviced a

MAYTAG WASHER

Model MVW6200KW4

Near Los Angeles, CA 91306

Sean W

Job Details: 10/29/2024

"Replaced damaged pulley,and defective actuator.ran diagnostic cycle successfully without errror codes or interruption.washer now working properly."

We serviced a

AMANA REFRGERATOR

Model ASD2522WRS07

Near Palmdale, CA 93551

Samson O

Job Details: 10/29/2024

"Replaced bad condenser fan motor kit recommended by the tech support, unit test ok. Cx to allow for 24 hrs for maximum cooling. Complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ10

Near Palmdale, CA 93552

Jonathan

Job Details: 10/29/2024

Replace defective valve and tested unit and is working properly

We serviced a

KITCHENAID REFRGERATOR

Model KBRS20ETSS01

Near Los Angeles, CA 91326

Ian Y

Job Details: 10/29/2024

Removed and replaced units bulbs and water filter housing. Unit now illuminated and water filter lid closes.

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW3

Near McFarland, CA 93250

Esteban S

Job Details: 10/29/2024

Broken actuator. Actuator was removed and replaced. Unit passed all test. Unit is working as intended.

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Barstow, CA 92311

Jonathan B.

Job Details: 10/29/2024

JB OUT 10/29/24Customer states unit will fill with water but not wash.Tested in NORMAL cycle. Verified nor fill function. Unit wash motor does not run.Installed replacement Sump and Motor assembly W12613579.Reassembled unit and tested again in NORMAL cycle with customer.Unit is now washing properly.No charge to customer.JOB COMPLETE

We serviced a

ZLINE RANGE - ELECTRIC

Model SGR30

Near Burbank, CA 91505

Oscar L

Job Details: 10/29/2024

Visual and physical inspection was conducted and through the functional testing a yellow feather was observed on the R F burner. So I have adjusted the orifice gas and air moisture and consumer was happy with results. Silvia 00833135

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FRSS2323AS8

Near Lompoc, CA 93436

Kash S

Job Details: 10/29/2024

"Found unit making excessive noise while IM filling, found valve vibrating against rear panel, secured valve and panel, verified with cx that unit is operating at normal noise levels, advised cx to monitor for further issues, unit is fully operational at this time"

We serviced a

WHIRLPOOL DRYER

Model WED8127LW2

Near Lathrop, CA 95330

William

Job Details: 10/29/2024

"Replaced drive motor & blower wheel, ran dryer cycle, unit operating as designed."

We serviced a

GE CAFE DOUBLE RANGE

Model CGS750P4M3W2

Near Ventura, CA 93003

Isidro

Job Details: 10/29/2024

"Installed new lower over bake igniter, unit is now igniting and operating as designed, advised customer to run a burn off for 45 minutes at 400 degrees , cx approved repair"

We serviced a

ZLINE RANGE - ELECTRIC

Model SGR30

Near Los Angeles, CA 91352

Samson O

Job Details: 10/29/2024

"Found red tag by gas company, I checked the pallet and discovered that the inner is far from the pallet, reinstalled inner closer to the pallet and unit test ok. No more gas smell. Complete"

We serviced a

WHIRLPOOL COOKTOP

Model KCGS556ESS05

Near Los Angeles, CA 91304

Sean W

Job Details: 10/29/2024

Wire for front right burner to spark module not making good contact.reconnected wire to spark module.cooktop now working properly.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFTR1814TW

Near Rosamond, CA 93560

Jonathan

Job Details: 10/29/2024

"Installed new washers, tested unit and is working properly."

We serviced a

BOSCH DISHWASHER

Model dwhd770w

Near Bakersfield, CA 93311

Randy

Job Details: 10/29/2024

Removed and replaced cord. Tested now working as designed

We serviced a

MAYTAG WASHER

Model MVWB835DW3

Near Glendale, CA 91207

Oscar L

Job Details: 10/29/2024

"After completing the replacement of previously diagnosed parts and components, a functional test was successfully conducted."

We serviced a

KITCHENAID ICEMAKER

Model KUIX535HPA01

Near Santa Clarita, CA 91321

Felipe S

Job Details: 10/29/2024

Install the new grill cutter on the unit. Retest the unit and now is working properly. Job complete

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FRSS2323AW7

Near Bakersfield, CA 93308

James

Job Details: 10/29/2024

"Removed and replaced made, manifold and water lines. Unit now working as intended with no more leaks."

We serviced a

MAYTAG WASHER

Model MVW5430MW0

Near Dinuba, CA 93618

J.E.

Job Details: 10/29/2024

Cycled unit and found mice infested causing damage to control board. Main harness and lid lock harness took pics and notified square trade. Not covered. Job completed

We serviced a

JENN-AIR DOUBLE OVEN

Model JJW3830LM01

Near Los Angeles, CA 90049

Tim B

Job Details: 10/29/2024

Replaced broken glass door. Unit functions as normal.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT311FZDW01

Near Los Angeles, CA 91356

Alejandro

Job Details: 10/29/2024

"Found the unit not cooling, verify the problem,compressor not running, replace compressor,service valve,drier,relay and capacitor, charge nitrogen,not verify leaks, make a vacuum charge refrigerant 4.9 oz R134a check compressor condenser and evaporator fan motors unit start work properly"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM7

Near Los Angeles, CA 91326

Ian Y

Job Details: 10/29/2024

Replaced missing end caps on units top rack. Top rack no longer sliding all the way out. Job complete.

We serviced a

GENERAL ELECTRIC WASHER

Model GTW335ASN2WW

Near Victorville, CA 92392

Cesar

Job Details: 10/29/2024

Replaced failed parts all tested good

We serviced a

WHIRLPOOL RANGE

Model WFG505M0MS0

Near Apple Valley, CA 92307

Cesar

Job Details: 10/29/2024

Replaced sensor all tested good

We serviced a

KITCHEN AID MW OVEN COMBO

Model KOEC530PSS00

Near Simi Valley, CA 93065

Paul M

Job Details: 10/29/2024

"Unit had a bad light inside of microwave, replaced harness and light bulb. Harness was broken and looked like it caused a short. After repair unit is working properly."

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Bakersfield, CA 93314

Brandon

Job Details: 10/29/2024

"Installed new harness, capacitor, and actuator. Unit is now able to run cycles to completion."

We serviced a

KITCHEN AID REFRIGERATOR

Model KBSD608ESS01

Near Los Angeles, CA 91352

Samson O

Job Details: 10/29/2024

"7740217440- Matt, unit need only reset from te panel, called tech support and advise cx to use for a while as all checked good. Complete"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ07

Near Redlands, CA 92374

Francisco

Job Details: 10/29/2024

"Checked u it found torn gasket, removed and replaced gaskets unit now working properly. No damage by tech."

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS07

Near Thousand Oaks, CA 91360

Felipe S

Job Details: 10/29/2024

"Remove old compressor and drier. Install the new seal system components on the unit and harness. Pressurize the system with nitrogen at 240 psi, no leaks found at this time. Vacuum the unit and unit holds the vacuum. Recharge the system with 55 grams of refrigerant R600a. Retest the system and the pressure with the unit running are, -5.3 and 62.4. This unit starts to cooling down, inform the customer they need wait at least 24 hours, for proper cooling. Job complete"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT2045VW2

Near Bakersfield, CA 93304

Raymond

Job Details: 10/29/2024

"Tech meant to use filter dryer, drier installed last visit. Contacted cx to make sure unit still cooling unit operating as designed."

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Los Angeles, CA 91306

Samson O

Job Details: 10/29/2024

"Replaced bad control board and shifter, unit test ok. Complete"

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Santa Ynez, CA 93460

Kash S

Job Details: 10/29/2024

"Replaced rotor, stator, slider and, control board, verified with cx that unit is starting cycle and operating at normal noise levels during spin, cx has no further questions/concerns, unit is fully operational at this time"

We serviced a

JENN-AIR ICEMAKER

Model JF42NXFXDE00

Near Los Angeles, CA 90049

Tim B

Job Details: 10/29/2024

"Replaced led lights and unit functions as normal. Cx refused gaskets. Called crystal, Cx paid enough,job done."

We serviced a

MAYTAG REFRIGERATOR

Model MRFF4236RZ00

Near Modesto, CA 95350

Timothy G

Job Details: 10/28/2024

"Cx showed video, Inspected unit and found that the condenser fan had been touching housing. Found mount tweaked screw in wrong hole. Removed and replaced properly. Unit is no longer making noise."

We serviced a

MAYTAG WASHER

Model MVW6200KW3

Near Simi Valley, CA 93063

Ian Y

Job Details: 10/28/2024

"Found units pulley wasnt secured tight allowing belt to fall out of place. Secured pulley with new nut with Loctite and positioned belt properly. Tested, unit now functioning as designed. Ran customer through how to load unit properly to get it not to shake. Loaded up multiple towels for her and ran a drain and spin as a demonstration. Customer Happy with explanation."

We serviced a

MAYTAG WASHER

Model MVW7230HC

Near Ceres, CA 95307

Timothy G

Job Details: 10/28/2024

Ran tests on unit and unit was not responding. Screen lit partially. Unplugged unit to inspect plugs. Found ui plug was half way. Plugged in and unit is now powered on. Unit passed all diagnostic tests. Job complete

We serviced a

WHIRLPOOL WASHER

Model WTW4957PW

Near Fresno, CA 93726

Timothy

Job Details: 10/28/2024

Ran a service test and found the unit is leaking at the water valve. Reset water lines and ran a service cycle. Unit checks ok.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF757SDHZ04

Near Santa Clarita, CA 91390

ERICK H

Job Details: 10/28/2024

Cx states noise coming from refrigerator when opening door. Confirmed sound. Sound is damper opening and closing. Adjusted damper. Unit operating as designed. Job complete.

We serviced a

FRIGIDAIRE DISHWASHER

Model FDPC4221AS

Near Lake Hughes, CA 93532

Jonathan

Job Details: 10/28/2024

"Customer informed me installation of dishwasher damaged there pumping, and drain hose was not installed properly, did not touch plumbing of client home. also found broken handle of unit, replaced handle tested unit and is working properly ; used 1 5304535626 (Handle) from stock"

We serviced a

MAYTAG REFRIGERATOR

Model MRFF4236RZ00

Near Modesto, CA 95350

Timothy G

Job Details: 10/28/2024

Inspected unit and found studs coming loose. Removed all handles and tightened studs. All handles tightened. Job complete

We serviced a

WHIRLPOOL DRYER

Model WGD5010LW3

Near Oxnard, CA 93030

Ian Y

Job Details: 10/28/2024

"Found unit with broken belt and pulley. Replaced belt and pulley. Tested, unit now rotating properly."

We serviced a

WHIRLPOOL WASHER

Model WFW560CHW2

Near Loma Linda, CA 92354

Rod

Job Details: 10/28/2024

Wont fill will waterConfirmed.pressure hose kinkedfeed kink..designed operation was restored.

We serviced a

MAYTAG WASHER

Model MHW5500FW1

Near Santa Clarita, CA 91355

Richard R

Job Details: 10/28/2024

"Upon arrival, inspected unit during plug in the unit in the union went straight into drain and would not stop draining unplugged unit remove top checked pressure switch found suds in pressure hose cleared suds out plugged the unit back in Unit stopped draining and was ready to start a cycle. I put the unit into diagnostics unit gave me an F3 one which is a pressure switch code put unit into diagnostic tests passed all tests and was no longer giving the error code unit possibly had an over sudsing and suds got into pressure hose causing pressure switch to trip and make the unit go into a constant drain. Unit is working as intended. Advise customer if they have any more issues to please give us a call back job complete."

We serviced a

WHIRLPOOL DISHWASHER

Model KDTM354ESS3

Near Los Angeles, CA 91326

ERICK H

Job Details: 10/28/2024

Cx states dispenser not opening. Replaced dispenser. Tested unit. Unit operating as designed. Job complete.

We serviced a

AMANA REFRIGERATOR

Model ASI2575GRS08

Near Fresno, CA 93727

Timothy

Job Details: 10/28/2024

"Opened the evaporator cover and found the line voltage connection not made at the element connection(see pics). Remade connection ,checked for security and applied a dielectric compound for better continuity.2.5k grey 25k pink"

We serviced a

KITCHEN AID COOKTOP

Model KCGS950ESS05

Near Visalia, CA 93291

Enrique

Job Details: 10/28/2024

"Customer concerns; cooktop smells gas under the cabinet. Found leaking gas line (I took pics). No parts needed. I tightened the connection to gas regulator, bubble tested ok, no leaks."

We serviced a

WHIRLPOOL WASHER

Model WTW8127LW0

Near San Luis Obispo, CA 93405

Jack

Job Details: 10/28/2024

Garret with tech line. 7739862579. Calibration and tested pump and pump and detergent is now working as designed. The setting on detergent was to low were it was putting out very very little soap. Ran full wash and soap is now coming out. Unit is now working as designed. After taking to tech line. Main board could have had a lot to do with controlling of detergent. Now after test. Working perfectly. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Los Angeles, CA 91331

ERICK H

Job Details: 10/28/2024

Latch clicking over and over. Latch has broken wire. Replaced latch. Tested unit. Unit operating as designed. Job complete.

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS3

Near Ventura, CA 93003

Kenneth

Job Details: 10/28/2024

Found unit leaking. Found customer was accidentally using laundry detergent pods and not dishwasher pods. Gave customer 2 cascade soap samples and instructed customer to leave her dishes a little soiled to help break down the soap suds. Put a fair amount of ketchup inside dishwasher to help it break down its current over suds situation to get customer back to where they need to be to use unit without any issues. Unit is working properly.

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Modesto, CA 95358

Timothy G

Job Details: 10/28/2024

"Ran vent test and unit failed. Cx had new vent hose that I put n for her. Unit is now passing test. No heat, replaced failed high limit thermostat and shorted heat element. Cx is going to use medium low heat. Unit is heating per design. Job is completed"

We serviced a

GENERAL ELECTRIC SSM1WW

Model GUD27ESSM1WWGUD27ESS

Near Hesperia, CA 92344

Brian G

Job Details: 10/28/2024

Inspected unit as necessary. Diagnosed ground wire at pigtail shorted to L1 terminal. Technician secured ground wire as manufacturer requires. Tested operation. All OK.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ2

Near Santa Maria, CA 93454

George

Job Details: 10/28/2024

Found dishwasher leaving plastic container extra wet at end of wash found unit with no jet dri refill retest unit functioning as design no errors.

We serviced a

MAYTAG WASHER

Model MVW7230HW1

Near Highland, CA 92346

Francisco

Job Details: 10/28/2024

"Cx stated unit starts then shuts off and does not go through cycle. Found f7 e4 code. Bolt missing at rotor, also found slider metal band slipping off. Removed and replaced slider/calibrated/ tested ops unit working properly. No damage by tech Cx approved.; used 1 W10734521 (Slider) from stock"

We serviced a

MAYTAG DRYER

Model MGD6230HW3

Near Oxnard, CA 93033

Isidro

Job Details: 10/28/2024

"Installed new thermostat and burner kit with coils, also thermo cut off sensor, tested and unit is now operating and heating as designed at this time of service, cx approved repair and service"

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ3

Near Bakersfield, CA 93312

James

Job Details: 10/28/2024

"Unit has slight clog in drain, cleared clog and ran drain cycle. Unit now draining properly. Unit under 1st year according to entitlements."

We serviced a

KITCHEN AID RANGE

Model KFGD500ESS11

Near Fresno, CA 93727

Timothy

Job Details: 10/28/2024

Replaced ignitor and tested unit. Top oven heating as designed.

We serviced a

GENERAL ELECTRIC DISHWASHER

Model PDT755SYR5FS

Near Corcoran, CA 93212

Enrique

Job Details: 10/28/2024

Installed lower spray arm. Dishwasher operating as designed. No leaks.

We serviced a

KITCHENAID DISHWASHER

Model KDTE104KPS0

Near Yucaipa, CA 92399

Rod

Job Details: 10/28/2024

******RETURNED UNNECESSARY PARTS*****Drain hose at dishwasher outlet leaking at vacuum break connection removed and reinstalled drain hose with no leaks returning.

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Riverside, CA 92508

Robert U.

Job Details: 10/28/2024

Found the unit not powering on. The main control does not have the indicator light while 122 volts are present at the control. Need to start with the main control. I checked the drain pump and ok at 20-21 ohms. The trip and diagnostic fee is 145.00 labor is a l14 187.92 error code and the main control cost is 361.81 with a sales tax of 31.66 so total is 726.39. Customer declined estimate. Only charging trip and diagnostic fee. 145.00

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Yucaipa, CA 92399

Rod

Job Details: 10/28/2024

Noisy in ffd compartmentconfirmeddefective air damper/diffuser. .replaced with no other issues revealed at this service.

We serviced a

WHIRLPOOL FREEZER

Model KBSD608ESS00

Near Los Angeles, CA 91356

Leon

Job Details: 10/28/2024

Replaced all selected parts Unit working properly as required

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW4

Near Santa Maria, CA 93458

Jack

Job Details: 10/28/2024

Checking out dryer to see why it worked then stopped. Unit is heating and found coils were bad at burner. Replaced burner and sensor. Unit will run longer now when tested. Job completed

We serviced a

WHIRLPOOL WASHER

Model WTW7500GC2

Near Modesto, CA 95355

Martin R

Job Details: 10/28/2024

Replaced Gearcase slide and drain pump tested unit washer is filling agitating draining and spinning per design job complete

We serviced a

MAYTAG DRYER

Model MGDC465HW0

Near Fillmore, CA 93015

Isidro

Job Details: 10/28/2024

"I cut the old motor shaft and removed old motor and blower wheel with saw saw, I installed and secured new motor, blower wheel and belt,unit is now spinning and operating as designed at this time of service"

We serviced a

MAYTAG WASHER

Model MHW8630HW4

Near Redlands, CA 92373

Francisco

Job Details: 10/28/2024

"Checked unit found f0 e2, f5 e2, cleared p switch and removed and replaced parts listed, tested ops unit working properly.Sr#7740207099"

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Yucaipa, CA 92399

Rod

Job Details: 10/28/2024

"Returned, replaced defective parts.designed operation was restored1 W11393685 (Transmission) and 1 W107345212542InStock (Slider)"

We serviced a

KITCHENAID DISHWASHER

Model KDFM404KPS2

Near Riverside, CA 92508

Robert U.

Job Details: 10/28/2024

Found after replacing the valve and the tub gasket the unit is no longer leaking. Also I removed the error code stored and ran diagnostic. All functions are now operating properly and no longer leaking. Job completed.

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Riverside, CA 92507

Robert U.

Job Details: 10/28/2024

Found the new stater has the same ohms reading 9.8 from white to red and white to blue. I ran a diagnostic cycle after replacing motor and no error codes stored. All functions are restored. Job completed.

We serviced a

WHIRLPOOL GAS RANGE

Model WFG320M0MS0

Near Tulare, CA 93274

Enrique

Job Details: 10/28/2024

Installed burner head. Range operating as designed. No gas leak.

We serviced a

WHIRLPOOL ICE MACHINE

Model GI15NDXZB0

Near Riverside, CA 92506

Robert U.

Job Details: 10/28/2024

Found the cutting grid open. Reason for failure because it should be 5 ohms and it checked open. I checked the new one and was at 5.9 ohms. All functions restored. Job completed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ16

Near Arroyo Grande, CA 93420

George

Job Details: 10/28/2024

Installed divider and auger motor and impeller tested unit functioning as design complete.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF577KPS02

Near Victorville, CA 92392

Brian G

Job Details: 10/28/2024

"Sealed system issue. Technician diagnosed restriction in system, causing intermittent cooling. Technician evacuated system. Leaked checked system with nitrogen. No leaks found. Removed and replaced drier. Charged unit with 56G of R 600. All OK. Allow 24 hours to stabilize.; used 1 W11109499 (Drier) from stock"