We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near San Miguel, CA 93451
Leo R
Job Details:
11/20/2024
"Enter diagnostics protocol, F7E1, F7E7, error codes found, check motor windings for Ohmage,Matt with tech line shifter, cap, motor and lower.Order following parts: W11026785 Motor, W11481722 Actuator, W11395618 Capacitor and W11643701 Wire Harness.SR # 7740368629.< ; ordrng 1 W11026785 (Motor.) and 1 W11481722 (Actuator) and 1 W11395618 (Capacitor) and 1 W10721967 (Splotch) and 1 W11643701 (Wire Harness)"
We serviced a
CROSLEY DRYER - ELECTRIC
Model YTD74E2SN1WS
Near Bradley, CA 93426
Leo R
Job Details:
11/20/2024
"Replace control board, heater element wire repair kit! Tyler with tech line, to test moisture sensor, Put unit back together and got a door open Fault code, order switch, it could be damaged,Ordering: WE04X28977 Door switch.File # 14897786.; ordrng 1 WE04X28977 (Door switch)"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Delano, CA 93215
Ron H
Job Details:
11/20/2024
Found drain pump not responding unit full over water unit had F9E1 code long fill pressure switch code and drain pump code odering drain pump harness and control; ordrng 1 W11399437 (Drain pump) and 1 W11643701 (Harness) and 1 W11626074 (Control)
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Turlock, CA 95382
Manuel B
Job Details:
11/20/2024
Washer wire harness broken again.call techline Sr#7740370471 instruct to order additional clip service pointer#w11284522; ordrng 1 W11643701 (Harness lower) and 1 W11284522 (Clip)
We serviced a
GENERAL ELECTRIC WASH/DRY COMBO
Model PFQ97HSPV0DS
Near Chowchilla, CA 93610
David C
Job Details:
11/20/2024
Found faulty heat pump ordering heat pump assembly ; ordrng 1 WE03X36780 (Heat pump) and 1 WE04X29950 (Inlet temp sensor) and 1 WE05X29927 (Temp sensor gasket) and 1 WE16X35694 (Blower fan)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Chowchilla, CA 93610
David C
Job Details:
11/20/2024
Found wire clipped off and cut ordering wire harness; ordrng 1 W11697178 (Wire harness)
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Los Banos, CA 93635
David C
Job Details:
11/20/2024
Found bearing spun out ordering gear case; ordrng 1 W11454741 (Gear case)
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Moreno Valley, CA 92557
Kevin
Job Details:
11/20/2024
"Unit not starting cycle. I found cam was stuck and caused actuator not to move. I removed and replaced cam but now the control thinks spin is agitation and agitation is spin. I recalibrated main control multiple times but programming is backwards. Ordering main control, belt and actuator. ; ordrng 1 W11481722 (Actuator) and 1 W11239857 (belt) and 1 W11556728 (Cntrl elec), used 1 W10721967 (DRIVE PULLEY) from stock"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Moreno Valley, CA 92555
Kevin
Job Details:
11/20/2024
New construction. Range console was scratched when customer performed walkthrough. Ordering new console. Unit under 30 days. ; ordrng 1 W11620706 (Console)
We serviced a
KITCHENAID M/W OTR
Model KMHC319LSS00
Near Bakersfield, CA 93306
Ron H
Job Details:
11/20/2024
Tech was assigned as a helper;
We serviced a
KITCHENAID ICEMAKER
Model KUID308HPS01
Near Glendale, CA 91206
Oscar L
Job Details:
11/20/2024
"Visual and physical inspection leaded me to a unit that its making ice but, its not cutting it due to a damaged cutter.Replacing such recommended.; ordrng 1 W10919199 (Ice cutter)"
We serviced a
MAYTAG DISHWASHER
Model MDTS4224PZ0
Near Loma Linda, CA 92354
Rod
Job Details:
11/20/2024
No action from the wash systemConfirmed.wash motor defectiveordering same; schdld next appmnt for 11/27 WED !
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Yucaipa, CA 92399
Rod
Job Details:
11/20/2024
Reschedule for next day. Contacting techline by phn no visit; schdld next appmnt for 11/21 THU !
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Yucaipa, CA 92399
Rod
Job Details:
11/20/2024
Not pumping water out and flashing lightsConsumer wants to have local vendor handle due to wait time. Does not want to wait for parts. W11643701wire harness. Declined further repair attempt; schdld next appmnt for 12/27 FRI !
We serviced a
MAYTAG WASHER
Model MVW5430MW2
Near Ridgecrest, CA 93555
Brandon
Job Details:
11/20/2024
Lid latch is broken. Ordering replacement.; ordrng 1 W11670519 (Lid latch)
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FG4H2272UF
Near Ridgecrest, CA 93555
Brandon
Job Details:
11/20/2024
Units freezer section is at 8°. Unit is showing high temperature alarm on the panel. Ice production has stayed consistent. Fresh food section is also running normal. Ordering new control and fan motor for repair.; ordrng 1 5304531885 (Control) and 1 5304523067 (Fan assembly)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHV02
Near Bakersfield, CA 93304
Raymond
Job Details:
11/20/2024
"E5 present, unit was never power cycled. Test 45 fills and test 57 harvests. Scheduling a call for Friday to see if unit started producing ice. ; schdld next appmnt for 11/22 FRI AM"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHB01
Near Merced, CA 95341
Cruz
Job Details:
11/20/2024
Need work- cx is experiencing intermittent freezing in ff compartment- ff compartment thermistor is reading out of range- ordering parts for 7nit. ; ordrng 1 W11293378 (Cntrl elec) and 1 W11724692 (Thermistor)
We serviced a
MAYTAG WASHER
Model MVW5035MW2
Near Bakersfield, CA 93307
James
Job Details:
11/20/2024
"Installed new harness, pump and control. Plugged unit in and drain began pump out. Pump out ran for 8 min and 35 second before topping and giving drain error. Press power and drain starts again with door locked. Will contact techline tomorrow and ordering new board; O-emld tckt"
We serviced a
KITCHENAID ICEMAKER
Model KUID508HPS01
Near Merced, CA 95340
Manuel B
Job Details:
11/20/2024
"Install circulating pump,Need main pump assembly.reroute for part.; ordrng 1 W11539855 (Pump assembly)"
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW0
Near Castaic, CA 91384
Felipe S
Job Details:
11/20/2024
"Upon arrival customer show me a video, when the unit turns on and start the cycle but after 10 seconds, the unit shuts off. Check the unit for error codes and found F5E4 and F0E1, this codes about door no open between cycles and clothes during cleaning washer. Call tech line to report this issue. After inspection found the wires harness form the stator to the ACU, has some kind of interference or malfunction, check stator winding and are good. This unit according with tech line will need new ACU and stator. SR: 7740365664 Nathan ; ordrng 1 W11354541 (Stator)"
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC3
Near Los Angeles, CA 91311
Sean W
Job Details:
11/20/2024
"Upon arrival found that door glass is shattered and not sealing properly,ordered new door glass.; ordrng 1 W11434304 (Glass door) and 1 W11676508 (Window seal) and 1 W11596131 (Seal)"
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ2
Near Bakersfield, CA 93311
Aaron
Job Details:
11/20/2024
Needs 2 call count Checked the unit touch control no longer works you cannot select temperature or bake or broil settings. As a result you cannot start the unit as well. Needs new console board assembly to repair the unit correctly.; rqstng P&A on 1 W11339755 (Console control asm)
We serviced a
WHIRLPOOL LAUNDRY
Model wtw4816fw3
Near Yucaipa, CA 92399
Rod
Job Details:
11/20/2024
"Severe off balance condition..worn out suspension and bad connector on machine control. Belt shredded.ordering controls d suspension assembly kit; ordrng 1 W11603810 (Control, mach) and 1 W10780045 (Suspension)"
We serviced a
KITCHENAID OVEN
Model KODE500ESS21
Near Redlands, CA 92374
Rod
Job Details:
11/20/2024
"*******VONNIE: Autho pending oven pull necessary to access parts replacementDisplays code F8 E0When both ovens display code Needs fans and appliance managers; ordrng 1 W11448962 (Control, copernicus) and 1 W11598200 (Control, Copernicus power supply) and 2 W11598119 (Blower, cooling fan)s"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Redlands, CA 92374
Rod
Job Details:
11/20/2024
Leaks water onto floor on lft sideConfirmed fill hoses not securely fastened to faucets nor product inlet valve.. secured in place. Found leaking softener dispenser as well. ; ordrng 1 W11569112 (Assembly disp/sw)
We serviced a
MAYTAG WASHER
Model WFW5605MW1
Near Los Angeles, CA 91342
ERICK H
Job Details:
11/20/2024
F6e3 error code present. Ui lost communication with acu. No other error codes present. ; ordrng 1 W11680389 (ACU) and 1 W11591400 (Console)
We serviced a
MAYAG WASHER
Model MAT20PDAWW1
Near Los Angeles, CA 91342
ERICK H
Job Details:
11/20/2024
"Cx states loud noise during spin cycle. Spun basket by hand. Grinding noise coming from damaged Gearcase. Cam and belt were damaged by Gearcase. ; rqstng P&A on 1 W11159068 (Gearcase) and 1 W10721967 (Cam), ordrng 1 W11213879 (Belt)"
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model PSE25KYHHHFS
Near Bakersfield, CA 93314
Esteban S
Job Details:
11/20/2024
"14710362 file number. Called tech line recommended shaving tube 1/8 did that. Let customer know to hold their cup 10 seconds after dispenser to catch water dripping. Cusp,er not happy with that they want follow up on this matter. ; saved tckt"
We serviced a
KITCHENAID RANGE
Model KSDG950ESS1
Near Bakersfield, CA 93309
Esteban S
Job Details:
11/20/2024
Ben sensor was removed and replaced. 7740369937. Additional will be needed for the unit. Recommended replaced. Control board and control panel. ; ordrng 1 W10915031 (Control panel) and 1 W11105615 (Display board)
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323AW9
Near Wasco, CA 93280
Esteban S
Job Details:
11/20/2024
Recommended 87739785 file number recommended sealing sealing where fill tube inserts to fridge. ; ordrng 1 5304525994 (Water valve)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW1
Near Shafter, CA 93263
Esteban S
Job Details:
11/20/2024
Motor getting power but not responding. Element tested good. Dispenser intermittently failing. Parts on order follow up required. ; ordrng 1 W11613479 (Motor sump assembly) and 1 W11705151 (Dispenser)
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW1
Near Riverside, CA 92504
Robert U.
Job Details:
11/20/2024
Found the unit full of water on arrival. The drain pump is not operating. Found the blue wire going to the drain pump broken right were it goes to the main harness. Ordering wire harness and will come back with the main control just in case. ; ordrng 1 W11643701 (Harness wire)
We serviced a
KITCHENAID OVEN
Model KSGG700ESS7
Near Riverside, CA 92506
Robert U.
Job Details:
11/20/2024
Found the spark module not sending power to the bake or broiler igniter for use of the oven. Ordered spark module to resolve. Also will come back with the man control but will not install until trying the spark module. ; ordrng 1 W10860916 (Spark module)
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Simi Valley, CA 93063
Richard R
Job Details:
11/20/2024
"Upon arrival inspected unit customer stated that unit will only since I put unit into diagnostic Scott an F7 E4 error code, which is basket cannot reengage put unit in diagnostic cycle unit did not want to shift and made a lot of noise trying to shift. I tried to remove stater not state or nut is seized onto stater and motor. Also tried to remove wash plate to see if there was anything lodged in there. Wash plate is seized onto transmission shaft. Both motor and wash plate will need to be cut off in order to make this repair ordering a stater, a rotor slider assembly a clutch a thrust washer, a gear case assembly, a spanner nut and a wash plate job. I need a two job count and a pre-authorization.; ordrng 1 W10915700 (Stater) and 1 W10915701 (Rotor) and 1 W10734521 (Slider assembly) and 1 W10754448 (Clutch) and 1 W11553312 (Thrust washer) and 1 W11449841 (Gear case) and 1 W11551646 (Spanner nut) and 1 W10902814 (Wash plate)"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Modesto, CA 95351
Andrew H
Job Details:
11/20/2024
Cx complaint. Not finishes cycling. Not draining water. Upon arrival. Ran diagnostics. Found broken lid. Lid mechanism faulty. Error code un balance load. Suspension rods faulty. Strike does not stayed seated in lid. Lid assembly cracked. W11396716 suspension rods. Lid latch mechanism faulty.W11413336 lid fault. ; ordrng 1 W11396716 (Suspension rods) and 1 W11413336 (Lid assembly)
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model GFE26JYMFS
Near Lancaster, CA 93535
Samson O
Job Details:
11/20/2024
"Found manifold head messed up due to cx trying to figure out out to change filter, causing the leak error code.; ordrng 1 WR14X34688 (Manifold) and 1 XWFE (Filter)"
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Los Angeles, CA 91606
Tim B
Job Details:
11/20/2024
Unit stayed I sensing and never going into wash cycle. Replaced capacitor and tested through diagnostics and unit functions as normal.; used 1 W11395618 (Capacitor) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Modesto, CA 95350
Cruz
Job Details:
11/20/2024
"Unit need a main cntrl, pump is continuously running- f7e1 long drain"
We serviced a
FRIGIDAIRE RANGE
Model FCFG3062AS
Near Tehachapi, CA 93561
Samson O
Job Details:
11/20/2024
"I adjusted the igniter closer to the pallet because its was far of causing gas buildup, oven works and reaches temperature between the recommended time frame, cx complain about the right front burner flame that its too high, unit flame its ok picture attached, lowest flame or warm flame cant be achieve on that particular burner, because its the biggest BTU, cx has options of other smaller burner with smaller BTU for that purpose. Unit test ok. Complete"
We serviced a
WHIRPOOL DRYER
Model WGD5000DW3
Near Camarillo, CA 93010
Isidro
Job Details:
11/20/2024
"Broken belt, Installed new dryer repair kit, unit is now operating as designed."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Azusa, CA 91702
Jaime
Job Details:
11/20/2024
Installed a new latch assembly washing machine OK
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Arroyo Grande, CA 93420
Jack
Job Details:
11/20/2024
Unit is leaking on the left side of unit from possibly the valve area. Checked out valve and took top off. Found hoses not tighten and followed the water through out unit. Came from valves were hose came from. Tested and unit is working as designed. Found f2e1 and no other codes. Job completed
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Santa Clarita, CA 91354
Felipe S
Job Details:
11/20/2024
"Upon arrival found unit with detergent on the bottom of the unit, no getting dissolved. Check the unit and found error code F7E1, this about single speed wash motor failure. Erase the codes and run the unit on diagnostic cycle, after diagnostic unit still have the same error code. Replace the pump assembly on the unit. Retest the uni, and now is working properly. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Ventura, CA 93003
Ian Y
Job Details:
11/20/2024
"Found units hot water valve backed out. Secured and tested, unit no longer throwing lo flo code."
We serviced a
WHIRLPOOL WASHER
Model wfw5605mw1
Near Oxnard, CA 93030
Isidro
Job Details:
11/20/2024
"Customer states unit was leaking water, ran diagnostics test found no leaks visible anywhere I opened the back panel , found water in drip Pan from leak look like dry suds on closer inspection found to what it looks like suds or foaming coming from back venting tube, too much soap or detergent being used"
We serviced a
MAYTAG LAUNDRY
Model MVW4505MW2
Near Santa Paula, CA 93060
Ian Y
Job Details:
11/20/2024
"Found pulley slipped loose knocking belt ajar. Secured pulley with new nut with loctide and realigned belt. Tested, unit now performing as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW0
Near Bakersfield, CA 93306
Raymond
Job Details:
11/20/2024
"Noise heard during spin, noise coming from Gearcase shaft causing worn splutch and belt. Cx declined at this time, will contact manufacture for assistance."
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Port Hueneme, CA 93041
Isidro
Job Details:
11/20/2024
Bad faulty capacitor unit is going straight to done when cycle is started. I installed new capacitor and unit is now agitating and spinning as designed
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Porterville, CA 93257
J.E.
Job Details:
11/20/2024
Cycled unit and found shorted control and capacitor installed new control and new capacitor retested unit working as designed job completed
We serviced a
WHIRLPOOL DRYER
Model WGD5010LW3
Near Los Angeles, CA 91331
ERICK H
Job Details:
11/20/2024
Cx states dryer not heating up after repairs done last week. Igniter wasnt glowing. Disassembled dryer. Igniter was unplugged. Reconnected igniter. Tested unit. Unit operating as designed. Job complete.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS01
Near Bakersfield, CA 93311
Aaron
Job Details:
11/20/2024
"Checked the unit temperature in the freezer 0°F , tested ice maker jammed , cleared the ice , tested harvest , passed ok unit filled up with water ok , reset the controls checked the air flow across ice bin operating ok now at this time , allow 48 hrs to start making ice and 3 days to fill ice bin"
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Los Angeles, CA 91331
ERICK H
Job Details:
11/20/2024
Cx states washer not powering on. Confirmed issue. Control failed. Replaced control. Tested and calibrated unit. Unit operating as designed. Job complete.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW0
Near El Monte, CA 91732
Andy
Job Details:
11/20/2024
"Not going in to spin and makes noise, found actuator,belt,pulley bad, replaced actuator,pulley and belt tested unit working properly"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Tehachapi, CA 93561
Samson O
Job Details:
11/20/2024
"Found cx using non he soap causing lot of foaming and leaks by the door side. Installation was tilted forward too that cause water to be in the switch tray, reinstalled unit and adjusted the legs and calibrate unit. Cx need to Change detergent though. Complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Lancaster, CA 93535
Jonathan
Job Details:
11/20/2024
"Tested unit found defective valve, replaced defective valve tested unit and is working properly, customer educated on use and care of unit; used 1 W11641117 (Valve) from stock"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ0
Near Palmdale, CA 93551
Jonathan B.
Job Details:
11/20/2024
"JB out 11/20/24.Customer states water in dishwasher is not hot.Upon arrival dishwasher was running a wash load.Opened dishwasher and verified water was slightly warm.Canceled current Wash cycle. Tested in NORMAL wash cycle and verified water being supplied to the dishwasher is far below the required 120f minimum as outlined in the factory supplied Installation guide (page #8). Water entering the wash tub is approximately 65-75f. House water heater is too far from dishwasher and HOT water pipe in concrete slab (November-February) is very cold and cools the water quickly resulting in cool water being supplied to dishwasher.Ran Diagnostics and extracted only one stored error code F7E1 indicating water is too cold. Cleared stored error code. Ran Service diagnostics and verified with customer present that the heating element does heat as designed but cannot heat the incoming water (74f) to the minimum of 120f. During heating element test, the heater melted ice cube quickly.Recommend the installation and use of a Point of Use Hot water heater mounted under the kitchen sink, supplying Hot water to only the Dishwasher itself set to a minimum of 125f. Reset onboard Computer Control..Also advise this model dishwasher has a stainless steel inner door panel but a Plastic wash tub. The plastic wash tub does NOT hold the heat and therefore will not dry ceramic, metal and glass items unless water temperature is no less than 120f and will not provide good drying results on Plastic items being washed as they do not hold the heat well.No charge to customer. JOB COMPLETE"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Laton, CA 93242
Enrique
Job Details:
11/20/2024
"Washer was not operating. Drain pump broken wire harness (black/white wire). Installed lower harness, performed calibration. Washer operating as designed. No leak. ; used 1 W11643701 ( Harms-wire) from stock"
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Palmdale, CA 93550
Jonathan B.
Job Details:
11/20/2024
"JB OUT 11/20/24Customer states washing machine makes loud banging sounds spin cycle. Upon arrival, tested washer and spin cycle verified door hinge loose. Tightened all mounting screws for door hinge and retested operation. Unit now, spins smoothly and quietly. Advise customer front load washers prefer, and are designed to hold larger loads and will spin more smoothly with larger loads as opposed to small wash loads. Additionally advised customer against use of HE turbo detergent and any detergent pods as they are too highly concentrated For this low, high-efficiency washing machine. No parts needed no charge to repair job complete."
We serviced a
WHIRLPOOL WASEHR
Model WTW8127LW1
Near Oxnard, CA 93033
Isidro
Job Details:
11/20/2024
"Broken strike, installed new latch assembly and strike, unit is now working as designed, cx approved repair and ser"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Bakersfield, CA 93312
Aaron
Job Details:
11/20/2024
"Checked the unit , washer doesnt recognize lid shut , checked the strike , busted , replaced the strike tested ops ok now at this time"
We serviced a
MAYTAG DRYER
Model MGD6230HW3
Near Simi Valley, CA 93065
Richard R
Job Details:
11/20/2024
Upon arrival inspection of unit found cycle selector knob seized and not working replaced control panel with new knob tested unit is now working as intended job completed
We serviced a
MAYTAG WASHER
Model MVWB855DC3
Near Lancaster, CA 93536
Samson O
Job Details:
11/20/2024
"F2E1; F0E3, found control board throwing overload error while the load is very small, inspected the slider and in between the basket and tub for friction, nothing. Unit need control board and shocks, cx declined estimate for repair, getting new unit. Complete"
We serviced a
WHIRLPOOL DISHWASHER
Model DU1055XTSS3
Near Los Angeles, CA 91344
ERICK H
Job Details:
11/20/2024
Cx states dishwasher not turning on. Found loose connection from power cord inside junction box. Tightened up all connections. Tested unit. Unit operating as designed. Job complete.
We serviced a
WHIRLPOOL WASHER
Model Mvwb765fw3
Near Moreno Valley, CA 92557
Kevin
Job Details:
11/20/2024
unit not draining and making scrape when basket is turning. I found that the slider is scrapping on clutch and drain pump has voltage but not draining. Unit will need slider and pump assy. Customer declined repair
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS05
Near Oxnard, CA 93035
Isidro
Job Details:
11/20/2024
"Water supply checked good from wall, I found a bad water valve. I installed new water valve unit is now dispensing water as designed, cx approved repair and service water valve, no leaks visible anywhere"
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Arroyo Grande, CA 93420
Jack
Job Details:
11/20/2024
"Unit was slipping wheelie in a med spin. Replaced parts cam, actuator and belt. Tested again and unit can spin out no problem. Tested and calibrated unit. Job completed ; used 1 W11239857 (Belt), and 1 W10721967 (Cam) from stock"
We serviced a
KITCHEN AID DISHWASHER
Model KUDC10FXSS3
Near Bakersfield, CA 93309
Aaron
Job Details:
11/20/2024
"Checked the unit upper rack was off the track , could have caused the unit to leak , repaired the upper rack and track assembly so it works correctly tested operations unit unit is working as designed now no leaks found at this time."
We serviced a
JENN-AIR DOUBLE OVEN
Model JJW2730DS01
Near Agoura Hills, CA 91301
Giovanni M
Job Details:
11/20/2024
"Needs 2x labor for the uninstall and then reinstalled of a stacked unit .I was getting a F2E1 error code. I uninstalled unit replaced the consul, then reinstalled unit properly. Tested unit after for function. Everything is working as designed at this time"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Tracy, CA 95304
William
Job Details:
11/20/2024
"Replaced hose connectors at bottom of door, Tested water valve operations, instructed cx on normal water valve functions. Unit operating as designed"
We serviced a
MAYTAG DRYER
Model MGDX700XL1
Near Moreno Valley, CA 92553
Kevin
Job Details:
11/20/2024
"Unit making loud noise during operation. Tested unit and found idler pulley making a loud noise and rollers are worn. Removed and replaced rollers, idler pulley and belt. Tested unit. All tests good."
We serviced a
WHIRLPOOL WASHER
Model WTW5005KW0
Near San Fernando, CA 91340
ERICK H
Job Details:
11/20/2024
Cx states washer shakes aggressively during spin cycle. Suspension has failed. Cx declined repairs. Job complete.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Fresno, CA 93706
Joe P
Job Details:
11/20/2024
"Codes F7E3, F6E3, F3E3.. cleared codes.Slider has fallen down. Ran diagnostic cycle all passed. Informed customer that stand pipe is plugged, informed customer he will to call a plumber."
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near Simi Valley, CA 93063
Paul M
Job Details:
11/20/2024
"Suspension were weak, replaced with new suspension rods. Calibrated unit and is now working properly."
We serviced a
FRIGIDAIRE RANGE - GAS
Model FCFG3083ASA
Near Bakersfield, CA 93314
Esteban S
Job Details:
11/20/2024
Clogged center burner. Burner was cleaned and cleared from food debris. All burners are working. Unit is working as intended.
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Sanger, CA 93657
Timothy
Job Details:
11/20/2024
Checked for faults and found 7-4(basket reengagement fault) found the unit has a damaged slider and rotor because of missing fastener. Called Square trade and told them the parts needed to repair thisW10734521 sliderW11260238 rotorW10752189 fastener
We serviced a
MAYTAG DRYER
Model MED7230HW2
Near Sanger, CA 93657
Timothy
Job Details:
11/20/2024
Element is open. Replaced element and tested. Returning unused parts.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Ridgecrest, CA 93555
Brandon
Job Details:
11/20/2024
Found lint blockage in blower wheel housing preventing airflow. Cleared and tested. Unit is heating normally.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Clovis, CA 93612
Joe P
Job Details:
11/20/2024
"Installed latch, ran diagnostic cycle test all passed. Job complete."
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Los Angeles, CA 91364
Giovanni M
Job Details:
11/20/2024
Replaced the sump and motor. Tested unit for function and leaks after. Everything is working as designed at this time .
We serviced a
MAYTAG REFRIGERATOR
Model MRFF5033PZ01
Near Los Angeles, CA 91403
Tim B
Job Details:
11/20/2024
Found line in back rubbing on fan. Adjusted out of the way. Also added screw to door hinge that was missing.
We serviced a
MAYTAG WASHER
Model MVWC465HW2
Near Modesto, CA 95356
Andrew H
Job Details:
11/20/2024
Cx complaint. Not finished cycle. Upon arrival. Mirand diagnostics. Found error codes for Long fill error code. 8-1. And Long drain cycle. Installed pumps for drain and valves for long filling. Tested components out okay. Operating as designed
We serviced a
KITCHENAID WALL OVEN
Model KOSE500ESS20
Near Wasco, CA 93280
Esteban S
Job Details:
11/20/2024
Oven control lost communication after power outage. Error codes were deleted. Unit passed all test. Unit is working as intended.
We serviced a
JENN AIR RANGE
Model jdrp748hl01
Near Ventura, CA 93003
Isidro
Job Details:
11/20/2024
"Installed and secured new rights side over blower cooling fan, mice issue bit the grommet on fan. I Tested the unit on bake to 350 degrees. Unit is now operating as designed at this time of service"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Bakersfield, CA 93306
Raymond
Job Details:
11/20/2024
Replaced compressor and evaporator. Recharged with 56 grams of r600. No leaks found u it regulating to temps.
We serviced a
GENERAL ELECTRIC WASHER
Model GTW720BSN0WS
Near Bakersfield, CA 93307
Randy
Job Details:
11/20/2024
Removed and replaced drain pump. Tested. Now working as designed.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFF507HPS00
Near Paso Robles, CA 93446
Jack
Job Details:
11/20/2024
Replaced led lights and checked out. Now unit is lighting as designed and checked out all other functions on unit. All checked out and passed. Job completed
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Los Angeles, CA 91326
Ian Y
Job Details:
11/20/2024
"Removed and replaced units ACU and latch. Tested, unit now going into cycles. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Los Banos, CA 93635
David C
Job Details:
11/20/2024
Found bolt from drive pulley loose and caused drive pulley to crack replaced drive pulley unit working as designed
We serviced a
MAYTAG WASHER
Model MVW4505MW
Near Visalia, CA 93291
J.E.
Job Details:
11/20/2024
Cycled unit and found belt slipped off causing damage to cam. Installed new cam and new belt retested unit now working as designed job completed
We serviced a
WHIRLPOOL WASHER
Model MVWB835DW4
Near Burbank, CA 91505
Oscar L
Job Details:
11/20/2024
"After hinge and new lid were replaced, proper functional testing of lid was successfully achieved."
We serviced a
ROPER DRYER
Model RGD4516FW
Near Santa Maria, CA 93455
George
Job Details:
11/20/2024
Found timer not turning replaced timer tested unit time running ok complete.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Los Banos, CA 93635
David C
Job Details:
11/20/2024
Found high limit cut off bad replaced high limit cutoff tested unit unit working as designed
We serviced a
GE MICROWAVE
Model JVM7195DF1CC
Near Bakersfield, CA 93313
Randy
Job Details:
11/20/2024
Unit door wont latch. Broken latch key on door. Needs a new door WB56X20639$208..
We serviced a
WHIRLPOOL REFRGERATOR
Model WRX735SDHZ07
Near San Miguel, CA 93451
Leo R
Job Details:
11/20/2024
"On arrival, Cx stated right door gasket is ripping, opened diagnostics program to check damper , test # 3, it passed 01- damper opens, 02- damper closes, No need to replace damper at this time.Cx advised to lower FC temperature from 37* to 39*,2 degrees Fahrenheit and monitor cooling in crisper drawer and cold spots, will check with tech line tomorrow on issue and get back to Cx.Additional parts included in attention notes."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHW04
Near Los Angeles, CA 91304
Sean W
Job Details:
11/20/2024
"Thermistor wire partially torn,replaced thermistor,fridge now cooling properly.; used 1 W11724692 (Thermistor) from stock"
We serviced a
KITCHEN AID REFRIGERATOR
Model KRFC302ESS00
Near Riverside, CA 92504
Robert U.
Job Details:
11/20/2024
Found the right side door gasket torn and not sealing. I replaced the refrigerator door gasket and heat treated for better sealing. I found the issue with the water dispenser and ice maker is the filter clogged. When I put my by pass plug the water dispenser and ice maker work. Recommend getting a genuine whirlpool filter. All functions of the door checked ok after repair. Job completed. Recommend leaving right door closed for the next hour or two.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Bell Canyon, CA 91307
Sean W
Job Details:
11/20/2024
"Motor is dead,replaced motor and sump assembly and successfully ran diagonal cycle without inturuptions or any error codes displayed,dishwasher now working properly."
We serviced a
WHIRLPOOL OVEN
Model WFG505M0MS0
Near Riverside, CA 92504
Robert U.
Job Details:
11/20/2024
Found the unit had a f2e1 error code stored shorted or stuck keypad. I removed and replaced the main control that has the user interface inter graded into it and ran a bale cycle. All tested ok after replacing defective touchpad control. Job completed.
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ01
Near Oxnard, CA 93030
Isidro
Job Details:
11/20/2024
"Installed new compressor, dye drier, service valve, heat exchanger tube and evaporator, pulled vacuum for 10 minutes unit held. Then charged with 5.5 onces of R134, unit started pulling heat and cooling as designed at this time of service"